Cisco SX20 and device 10 "touchscreen

Similar Questions

• Cannot launch the call to Polycom V700 to Cisco SX20/EX90

  Hello

  I am configuring a Cisco SX20 and a Polycom V700. I can call to Polycom Cisco, but can't call Polycom to Cisco. It proved a mistake, "your call could not be connected because the call was was routed through a network of intermediary that is not service the remote site." Please contact your network administrator. "But I have that in place inside the LAN, and there is no firewall on the inside.

  I've tried with EX90 as well, but it's the same thing.

  Can someone please advise me what I missed?

  Concerning

  Robi

  Hi Robi,

  I'm kinda a waste, then as to why it does not work... If you have enabled IP H.323 gatekeeper OFF, call preference value IP H.323, numbering method with H.323 Auto in 1st preference and all other disabled protocols - it should just really work when you dial an ip address...

  I guess the next thing to look at would be the version of the firmware on the polycom - is recent (or maybe an older buggy)?

  In addition, you could try a factory reset on the device (just to make sure there is not another stuck somewhere setting) and to reconfigure settings you need.

  Wayne

  --

  Remember the frequency responses and mark your question as answered as appropriate.

• Injector POE 10 SX20 and tactile

  Hi all

  Tap 10 includes POE as Touch 8 injector?

  If this isn't the case, when we use 10 touch with the SX20 and there is no switch POE, CTS-POE-NIJ is necessary, I guess.

  But we can control CTS-POE-NIJ separately on CCW, so if you forget to order CTS-POE-NIJ with SX20, what can we do?

  10 Touch works with standard POE injector like that?

  http://www.TP-link.com/LK/products/details/?model=TL-POE150S

  Kind regards

  Kotaro

  None of the documents I've seen says that the PoE injector comes with the Touch 10.  Because they were originally designed for the MX series include the port 10/100 PoE to connect to and the SX10 compatibility and SX20 has been a recent addition of compatibility (in TC7.2 +), I guess that if you ordered one, it would not come with the PoE injector.

  The only documentation of note that I found (the SX80 administrator guide) says that there need to be a Midspan PoE injector, or to power it with a PoE switch.  So, any 802.3af injector that works with Touch 8 should also work fine for 10 touch.  (And Yes, a quick glance at the specifications, the device of binding TP that you linked seems to be a device that would work).

  You can probably order the good injector PoE of CIsco on CCW, you just find the correct part number high range - similar to the additional licenses for endpoints - these can be a little hard to find if you don't know the right of departure (and, no, I don't know where to find the PoE injector but maybe someone else can help).

  Otherwise, you can wait a few months and you will be able to pair it directly via the USB port (the TC7.3 release notes: "A Cisco adapter USB-to-Ethernet brand will be available in March 2015").

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• xhistory Cisco SX20 codec calllog

  Hi all

  Can someone help me? I have a Cisco SX20 with the version of the TC7.2.1 software, I´d as know, if a limitation extracting SX20 call logs using the command line:

  xhistory calllog appeal

  I extracted the last 30 days, always, once the month.

  TKS,

  Caesar

  You may have been able to see some newspapers, but this is not a complete list of all calls (at least that you didn't really use the unit much at all).

  With TC7.2.1, you can retrieve the call history via the web interface in a more readable format (Diagnostics, historical calls) - but to have a glance at it, it shows only the last 100 calls (which, for the unit, I looked it is a matter of days, not the "last 30 days" you are after).

  You really need TMS to capture and save the CDRs to be able to report for any significant period of time.  You can download TMS and run as a demo version to report up to 3 devices without any permit.

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• 0 x 80070035 and 0X80004005 error codes when you try to connect to other computers and devices on the same network - unable to connect to the shared devices.

  I have a network consisting of Windows 7 laptop computers, an XP laptop and a Wireless Linksys (Cisco) WRT610 N + N with storage attached to it via its USB port.  Your PC Windows 7 has, since I can see and access to other computers and devices on storage.  Since Windows 7 PC B I can not connect (via the file manager) to A PC or NAS storage network.  Get such as 0 x 80070035 and 0X80004005 error codes when you try to connect to the IP address on the device name.  When I ping the devices of PC B I have no trouble to achieve.

  I turned off all firewalls, added the LMHOST file entries and a myriad of other tests and still cannot connect to PC B devices.  I can surf the net fine and do everything else - simply cannot connect to other devices even if these other devices can connect to me.

  I was in there for 22 years and has worked as an engineer on major networks and the network I stem - anyone got any idead. I checked all the basics such as Netbios, file sharing etc etc.

  It took a reinstall (upgrade) to get actually it works again.

• Cisco VCS and integration Lync2013

  Hello!

  Could you tell me please, when CISCO officially support Lync2013 - free new software for VCS - C and documentation on integration?

  The main interest is the possibility of transferring video between CISCO/MCU and Lync endpoints on the H.264 Protocol, who hails from Lync2013.

  Right now, I've got VCS - C and RTM Lync2013 X7.2. During the video call without AMGW appeal established as audio only.

  When using with Lync2010, it worked on Protocol H.263 and CIF resolution.

  Evgeniy salvation,

  We are currently investigating the possibilities to achieve interoperability between Lync 2013, VCS and video devices on the side of the VCS standards-based, it is a work in progress and at this stage, it is to early to provide any factual information on when interop will be available.

  In contrast to Lync 2010, Lync 2013 does not support H.263 for video and it so that will remove the OCS/Lync integration. I do however think that you should be able to make a two-way video between Lync 2013 and VCS-joined endpoints if you use an AMGW tried that yet?

  Thank you

  Andreas

• Cisco ISE and Meraki RADIUS

  I am very new to Cisco ISE and Meraki.  I try to get the Radius configuration for wireless authentication.  When I do a test of the Meraki to ISE, it passes.

  When I try to connect from my laptop, I look at the logs of the Radius and it passes; However, it does not connect me to good policy.  I keep hitting the default policy.  I have my Meraki police above the default policy in the strategy defined in article.  I have attached what looks like my strategy game.

  Devices does not really matter. Here is what I see when I create a device group (where you add the access point to this group), and then create the condition:

  networkdevicegroups.PNG

  

  And here is where I create the condition of strategy game and you should be able to select the Meraki access points:

  devicecondition.PNG

  

  This will give you the condition similar to what I posted above. This is perhaps why you aren't hit that is not matching the condition for this game.

• What ports must be used between SX20 and Intouch?

  Hello.

  I'm a junior engineer of telepresence,

  I face to make matching SX20 and Intouch. They have the same subnet mask and even G/w.

  with this configuration, I had things qurious.

  Question,

  1. in the event that they must have the same mask subnet and the same G/W? If so, why?

  2. which ports to use when pair SX20 and Intouch?

  3. how to pass the NAT H.323 mode

  (I know what WE / OFF mode and also how it works, but I did not understand the Auto mode, there is no document on this subject)

  This is just my thinking I hope I'm wrong.

  I'm afriad that Auto mode automatically calculrate the audit of public or non-public of logical IP subnet internal,

  After that, decide Tochange source ip or keep when H.323 call.

  If that, what users have public IP addresses and use them as private with the exception of a few ip for security, IPs

  and they use for NAT 1:1 or PAT to use internet. So how do they check it's private or public.

  Sorry for the reading of inconvient it, it isn't my mother tongue. and I wish the goodness of the expert.

  1. in the event that they must have the same mask subnet and the same G/W? If so, why?

  No, inTouch able to pair with the codec of subnet different until properly configured gateway IP address.

  2. which ports to use when pair SX20 and Intouch?

  SSH

  3. how to pass the NAT H.323 mode

  Please see the https://supportforums.cisco.com/message/3794585#3794585 which had the same discussion.

• SX20 and link ISDN with TC6

  Hi guys,.

  I recently upgraded a SX20 and link ISDN to the new TC6 and after the upgrade, I can't make ISDN call.

  I can see and manage the ISDN link from the SX20 configuration web page, but the status of the ISDN connection is: error, SIP not saved.

  I use H323 network and I don't use SIP between SX20 and ISDN link and with the old version, I could receive and make calls. Now when I try to dial the ISDN using the new interface TC6 endpoint indicates that it does not find the ISDN link.

  Thank you for your help,

  Adrian

  Hi Adrien, Valentine's day.  Theres something happens with outgoing enabled on the link and the Codec for this, and we have two CDETS opened on them.  There are always SIP service is enabled on the Codec with link and link itself.  Codec uses IPV6 local links for the link itself.  Even if the sip xstatus on the codec has its inactive etc, the codec message still SIP REGISTER to the device registration link.  Link runs a FWD SIP process that handles the request.  Sorta like a mini SIP registrar if you want.  Codec will send the message to REGISTER using link-local IPV6 address.  Example of message is less than 200 Ok.

  77582.64 SipPacket PacketDump: Proto: SIP, name: REGISTER sip: [0000::000:0000:0000:cd39]: 15070 SIP/2.0, Direction: outgoing, RemoteAddress: [0000::000:0000:0000:cd39]: 15070, GroupEntity: b27d07c1f5f298c492db68040b320ca6, time: 77582634 content:!

  77582.64 SipPacket REGISTER sip: [0000::000:0000:0000:cd39]: 15070 SIP/2.0

  77582.64 SipPacket Via: SIP/2.0/TLS [fe80::250:60ff:fe83:c52a]: 5061 branch; = z9hG4bK45a7681a50ebbdc5b98e2f91bff6b438.1; rport

  77582.64 SipPacket Call-ID: b27d07c1f5f298c492db68040b320ca6

  77582.64 SipPacket CSeq: 47083 REGISTRY

  77582.64 SipPacket Contact:

  «': 5061; transport = tls >; + sip.instance =»

  77582.64 SipPacket of:; tag = 116a994ac2281c72

  77582.64 SipPacket to:

  77582.64 SipPacket Max-Forwards: 70

  Road to SipPacket 77582.64:

  77582.64 SipPacket allow: INVITE, ACK, CANCEL, BYE, update, INFO, OPTIONS, CONSULT, INFORM

  77582.64 SipPacket User-Agent: TANDBERG/518 (TC6.0.0.876266)

  77582.64 SipPacket expires: 3600

  77582.64 SipPacket authorization: Digest-nonce = "d9605a7da8be22af8c0e7f52b3de4a5f5125fcd3", domain = "MARCIE", qop is auth, username = "djkvvknn", uri is "sip: [0000::000:0000:0000:cd39]"

  ", response ="3b27b753cb9bcf38cc2431b767bce643", algorithm is MD5, nc = 00000002, cnonce ="84addca2a68f6c5f9b657a94653a4bae"

  77582.64 SipPacket supported: replaces, timer, 100rel, gruu, way, way out

  77582.64 SipPacket Content-Length: 0

  77582.64 SipPacket

  77582.64 SipPacket >!

  -----------------------------------------------------------------------------------------------

  77582.65 SipPacket SIP/2.0 200 OK

  77582.65 SipPacket Via: SIP/2.0/TLS [fe80::250:60ff:fe83:c52a]: 5061 branch; = z9hG4bK45a7681a50ebbdc5b98e2f91bff6b438.1; rport = 41246; receipts = 0000::000:0000:0000:c52a

  77582.65 SipPacket Call-ID: b27d07c1f5f298c492db68040b320ca6

  77582.65 SipPacket CSeq: 47083 REGISTRY

  77582.65 SipPacket of:; tag = 116a994ac2281c72

  77582.65 SipPacket to:; tag = e84d13204776ebc2

  77582.65 SipPacket server: fwd

  77582.65 SipPacket Contact:; (+ sip.instance =""

  77582.65 SipPacket Content-Length: 0

  77582.65 SipPacket

  77582.65 SipPacket >!

  -------------------------------------------------

  I removed my own addresses, so you get the picture here.

  It is the same for the link.  Link will send REGISTRY as well to himself.

  Even if your using H320 as outgoing Protocol call, messaging between the codec and the liaison unit is still SIP as the outgoing call is still SIP of the codec for the link even if you chose H320.

  You can see all happening all by running: Journal ctx sippacket debug 9 and connect the output to see the messaging back and forth between devices.  This is why the Service SIP on the codec cannot be disabled.

  The outgoing enabled on both devices and it records not as what Adrian has met is odd. So the question has been filed and is under investigation.

  CSCue57128 - SIP in a strange state connecting to link ISDN (Codec)

  CSCue73049 - outbound SIP on ISDN link activation causes lose her registration (link)

  These are new, so the visibility may not be there yet.

  If you see a problem with the link is not not able to register, check to see if outgoing SIP are enabled on the link.  If so, turn it off and start.

  Do the same on the codec as well.  Disable outgoing SIP and restart the computer.  There may be some cases, you do not see this, as the investigation continues with the bug above two ID's

  I hope this helps.

  VR

  Patrick

• Codec for the CISCO SX20 problem

  Hi all

  I have a system SX20 and its codec seems to never start,

  The power LED button flashes slowly,

  The Ethernet connection does not work,

  There is neither video nor audio, signal

  It seems to be in standby mode, but ir never wakes up,

  I can't access the web interface,

  I also tried to reset by using the power button,

  Thanks in advance,

  You can try to connect to the SX20 with connection in series (see this thread for some options - 8 Post by Tanja Bader) and see if you are able to see all messages on the console.

  Otherwise, it looks like you need to RMA the device.

  Wayne
  --
  Please remember the tor frequency responses and mark your question as answered as appropriate.

• What is the difference between Cisco NAC and ACS?

  I am currently part of a new construction project and my Cisco account manager and sales engineer recommend Cisco NAC for our new MDF. I'm confused because I don't clearly know the difference between a Cisco ACS and the NAC. What is the difference?

  Thank you

  Chris

  Chris,

  The two are completely different, maybe the sales rep could present you with more information and application. Each offers a variety of services tailored to the specific needs. I think that we need to read more in depth on the proceeds of the NAC. NAC seems an excellent solution for authentication authorization but other regulatory compliance.

  When you see ask your representative to sales for more information/demo.

  ACS is more widely use as a central point to access control to network devices routers, an example is for acs accounting management and the authority to order on all devices on the network using acs as RADIUS server. Considering that the NAC is over a central point of safety inspection on earlier systems of access to your network by via LAN or outside, an example of these respected regulatory defined could be inspections could be virus definition checks before getting lan access thus preventing access to the LAN if the system does not have regulatory compliance defined in NAC access is denied. Another example could be the unknown local host connections etc... So, it seems that NAC is a much broader product that provides endpoint security internal, not only the authentication authorization as acs... ACS has been there for a long time, NAC is rather new product.

  NAC

  http://www.Cisco.com/en/us/NetSol/ns466/networking_solutions_package.html

  http://www.Cisco.com/en/us/solutions/collateral/ns340/ns394/ns171/ns466/ns617/net_qanda0900aecd800fdd6f_ns466_Networking_Solutions_Q_and_A.html

  ACS

  http://www.Cisco.com/en/us/products/sw/secursw/ps5338/index.html

  Rgds

  Jorge

• Portege 7020 error message: PXE - E01 PCI vendor and device ID do not match

  Hi all

  I get this error message (ID PXE - E01 PCI vendor and device do not match) when starting, when I use my portege 7020CT on a cd-docking station. The error message occurs only when I boot with the power adapter.
  I know what means the error message, and I tried to change the boot priority and the BIOS update. None of that helped him. I can't say when the error occurred since I used a LAN card wireless for a long time.
  The ethernet LAN for now, so im card dosnt work using an ethernet pccard.

  Toshiba has released a "patch" for this problem but only with the station of transhipment on the DVD, I also tried, but it didn't work either.

  What seems strange is why the problem only occurs when the power supply is turned on?
  When the message appears, the screen is locked and I can not pass.

  hope someone can help me.
  / Dreadeye

  Hello

  Well, you're right. This message is displayed if it of not possible to boot from LAN.
  In this case, it s advisable to change the boot priority.
  But it seems that you have already tried to change this option. It s very strange questions because it s occurs only if the power supply is turned on.
  I n t really have no idea, but I found this site:

  http://support.Intel.com/support/network/adapter/1000/sb/CS-010508.htm

  Try installing the latest Boot Agent. I put t know if it helps but you can try it.

  Good luck

  Good bye

• I dropped my iPhone 4S and now the touchscreen does not work. Is there a way I can fix it without having to buy another or should I buy another?

  I dropped my iPhone 4S and now the touchscreen does not work. Is there a way I can fix it without having to buy another or should I buy another? (my screen is cracked)

  From what I see, Apple does not screen repair for any older than the iPhone iPhone 5. I don't see off-warranty, replacement cost for 4 on their page of repair, but I'm figuring you would spend at least $200 to get a new.

  Would be better to see if your cell phone operator has the options of upgrade for you.

  ~ Lyssa

• Lack of cRIO 9154 in the add targets and devices dialog box

  Hello again all you lovers forum useful!

  I have an existing LabVIEW project which includes a Hypervisor PXI real-time target.  One of the devices that target is a chassis cRIO 9114.  I now need to add a cRIO chassis additional 9154 so according to a conditional disable signal, I can modify my code to talk to the old chassis or the new chassis, which keeps my modular code across different hardware.

  However, I write my code update on my regular computer which is not hooked to the target, so when I right click on the target of the hypervisor in my project and select new-> "targets and devices...". ", I can not select the" existing target or device "to be detected automatically.  Instead, I click on the 'new target or device' to add just anyway, and I expand the CompactRIO there, and... no 9154.  I have a bunch of other cRIO features (see screenshot), including the 9114, but no 9154.

  I guessed that maybe my LabVIEW installation (2012 SP1) know not this chassis when it was released last year, so I tried to install the latest drivers from device with discs on developer LabVIEW 2013 that I just got, but he hung up during installation (the first time at 0% the second time at 27%, listed as "Validating install" for long, long before I was abandoned and cancelled).  I restarted my computer, but no change to this problem.

  Does anyone have any ideas as to why I can't choose a newer chassis to insert in my project without that it is actually attached to my computer?  And I was too quick to renounce installation of the driver, not that I don't know if that would have solved the problem anyway?  : PEI

  Thanks for your help, as always,.

  -Joe

  

  Hello Joe,

  The 9154 NOR is a RIO MXI-Express chassis that's why it should appear under the section of chassis MXIe-RIO.

  

  For installation if you are concerned that it has not installed correctly, you can try run a repair on the NOR-RIO software and look at MAX to see if you have RIO 12.1 or 13.0.

• The Epson Workforce 600 is connected via a usb cable, the other is a wireless network. I reinstalled the software of the printer (Epson) and it shows in printers and devices, but it does not list

  I have two printers installed on my laptop, only appears.  The Epson Workforce 600 is connected via a usb cable, the other is a wireless network.  I reinstalled the software of the printer (Epson) and it shows in printers and devices, but it is not the list when I go to print something.  When I select "Find a printer", it gives me a list of computer icons.

  Hello

  Check with Epson support, their documentatiion online and drivers. As it's Epson OEM
  responsible for the proper functioning of the printer and their drivers provided.

  Good luck, you need to update or reinstall the latest driver.

  Epson - Support us.
  http://www.Epson.com/cgi-bin/store/support/SupportIndex.jsp?BV_UseBVCookie=Yes

  Epson - support from Europe
  http://www.Epson.co.UK/support

  =============================================

  The main issue is probably the drivers, but these can help:

  Add or remove a printer
  http://Windows.Microsoft.com/en-us/Windows-Vista/add-or-remove-a-printer

  Solve printer problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  Open the printer Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Find the manufacturer's Web site
  http://Windows.Microsoft.com/en-us/Windows-Vista/find-a-printer-manufacturers-website

  Find and install printer drivers in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/find-and-install-printer-drivers

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">