Input analog don't read do not correctly in normal mode

Similar Questions

• HP 2000-2B09WM DVD drive don't read do not; a Windows 8

  HP 2000-2B09WM DVD drive don't read do not. I have Windows 8 OS. Have you tried the MS CD/DVD it Fix troubleshooter and I am given the following: media in the CD/DVD drive is not readable (hp DVD A DS8A8SH SATA CdRom Device)... Not fixed.

  So, how can it be resolved? Thank you.

  Hello @jsilvester2006 ,

  Welcome to the HP Forums!

  I understand that your CD/DVD drive on your laptop does not work.

  Can you please answer the following questions:

  You have recently installed software or Windows updates?

  When did you start in this topic?

  Have you tried several DVD?

  Make sure you have the latest version of the installed CyberLink PowerDVD software. Without this software, the DVD drive cannot read DVD or Blu - ray discs. You can download this software here: the CyberLink PowerDVD software.

  You can also try to do a restore system before the issue started if it a question recently of news. You can access the restoration through the HP Recovery Manager by tapping the F11 key, while the portable lights.

  I would like to know if it works for you.

• Smart card reader does not correctly connect once the virtual machine is restored from sleep using the vmrum controls

  Smart card reader does not correctly connect once the virtual machine is restored from sleep using the vmrum controls

  Scenario is,

  1. smart card reader is connected to the VM with card inserted in

  2 initiate a prompt suspension of the VM toolbar

  3. now to resume the virtual machine by using vmrun command into the host machine

  WS t vmrun start xxx.vmx

  Now, the recovery of VM but the smart card reader that was previously connected does not work properly in VM that is to say, sometimes after CV chip card reader driver is uninstalling and a few other times, chip connected to the drive is not available on a virtual computer

  My requirement is after power, smart card reader can stay connected to the virtual computer with the already installed driver and the smart card.

  Kindly help with this problem.

  Host operating system: Victoire 2012 R2

  The VM OS: win 10 x 64

  Thank you!!

  Dear all,

  I had a work around for this problem. By adding "usb.autoConnect.device0 ="0xVID:0xPID"" this statement to the VMX file, solves this problem, that is, whenever the VM is wake-up by clicking on the link CV or using vmrun commands, it connects the unit in question automatically and it is charging correctly with his driver. Obtaining smart card detected after sleep\hibernate with no problems.

  VID & PID is respective ID of the device that can be seen in the properties of the Device Manager "Device Instance path".

  For more information about this, visit VMware KB: automatic connection of USB devices to the virtual machine power on

  ~ Surendra

• Windows XP Professional does not work in normal mode. I can't find my Windows CD to repair it but. What are my options?

  Windows xp pro does not work in normal mode.  I can make it work in safe mode.  I can't find my XP cd.  I don't have the serial code and key.  How can I load xp and try to fix the problem.

  Thank you
  Mike

  original title: need windows xp pro

  Hello

  Since it works fine in safe mode, I suggest you to try to perform the audit and the boot if it helps:
  http://support.Microsoft.com/kb/310353

  NOTE: When you are finished troubleshooting, make sure that you reset the computer in start mode normal such as suggested in step 7 of the above article.

  It will be useful.

• After you have installed SP3 (on XP with SP2), the PC does not restart in normal mode, only in safe mode

  After you install SP3, PC does not restart in normal mode, only in safe mode, without giving a clear indication of what is the problem or how to fix it - other than say to check settings in the Panel (not very useful).

  PC is a Compaq Presario desktop with AMD processor, model #: SR1720AN product #: EL540AA-ABG

  I reinstalled the operating system recovery disks, which reformats HD and installed XP with SP2.

  I then installed the SP3 from a flashdrive (361 MB files). Everything went without hiccups, but final restarts, he won't get to normal mode, safe mode only.

  I did it twice.

  Any ideas? Thank you.

  Here are the specifications of your desktop Compaq Presario SR1720AN. According to the specification, this model comes with a processor AMD and Windows XP Home Edition SP2 installed at the factory. According to your description, it seems that the HP recovery discs may have been poorly photographed for an AMD-based computer. Please see this Microsoft article and this HP document about your problem.

  To solve your problem, please reinstall Windows XP SP2 by booting from your HP recovery disks. After Windows XP SP2 is complete restored and that your computer is operational, download the "Windows XP SP3 with AMD CPU upgrade utility." Run this utility, and then restart your computer. Then download the "Windows XP Service Pack 3 Package of Network Installation" for it professionals. You can also try to use the SP3 Installer on your USB. Install the update to Windows XP SP3 and then restart when you are prompted to.

  This solve your problem?

  Please send BRAVO

• DVD RW drive (e :)) don't read do not all disks)

  I have a Dell Studio Windows Vista. The DVD RW drive (e :)) does not.) Regardless of the type of disc that I put in, my DVD player does not recognize. When I go to 'My Computer' to open the disc manually, a message appears telling me to insert a disc, even if it is already inside. In addition, when this message appears, it ejects the disc I have here. I did everything. My computer is up to date. I went to the only Device Manager update my CD/DVD drive and it is already up to date. I don't know what to do from here.

  Hello

  Check with Dell Support, their drivers and documentation online and ask in their forums known issues.

  Dell support
  http://support.Dell.com/

  Dell support drivers - product manual & warranty Info (left side) - and much more
  http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

  Dell forums
  http://en.community.Dell.com/forums/
  =========

  You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
  Playback of CD and DVD). So it is not unusual for parts from 1 or 2 to not work so that others do
  correctly. Since it accepts no disc do not forget to remove ALL the power and control the
  cable connections - remove and replace (at both ends where possible).

  Burning at low speed, or by using the master could help. A CD/DVD cleaner might help.

  Brand of the CD or DVD drive can also be the problem. Low quality (cheap brands) are always problematic.

  CD/DVDs have a tolerance + - and your can read/write on the edge outside these discs
  tolerances. They may be delivered, but it is generally more economical to replace the disk.

  Several good info here:
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
  http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

  ===========================================

  This troubleshooting could not help if there is alignment and/or wear issues however it
  a shot.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• The reader of CD/DVD reading CD and DVD incerted incerted, no clue don't read do not?

  CD/DVD read/write driver reads CDs but is unable to read the DVDs. suggest, if there is no solution for the problem.

  Hello

  You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
  Playback of CD and DVD). So it is not unusual for parts from 1 or 2 to not work so that others do
  correctly.

  Several good info here:
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
  http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

  ===========================================

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Topics restores do not correctly in design mode

  When you use em sizes or in CSS, the titles are not correctly make in Design view (HR 2015).

  This allows to reproduce very easily: create a blank project, edit default.css and make the following settings:

  H1, h2, h3 {p}

  do-family: Arial;

  do-size: 100%;

  }

  Now the headings 1, 2, 3, and paragraphs should all displayed in the browser's default font size (usually 16px).

  In the overview of the topic (and in all modern browsers), this is exactly the case:

  

  However, looking at the same subject in Design view, all titles are displayed in different sizes, and each of them are too big:

  

  It seems that design mode is ignores education % of the size of the police and set uses inherited sizes instead.

  With 1em instead of 100%, the behavior is exactly the same.

  Therefore, I'm unable to use % or em sizes in my HR project because headers are displayed in sizes ridiculously blasts upward. (In the example above, they are not, but normally you would use something like 180%, 150%, 120% for securities).

  It is very unpleasant, as using % or em is state-of-the-art for the delicate design. Can you please fix this or provide a work around? Using px sizes is not a workaround solution ;-)

  This a very annoying bug that's been around for years. Please log a bug with Adobe report: https://bugbase.adobe.com/

  As a solution, I use 2 CSS files. A point that I use to work in RoboHelp. And the other I have manually add to my output to crush the fixed size of CSS. No easy solution, I'm afraid.

• Web in Muse not displaying fonts do not correctly in design mode

  Curious problem - in mode Design of Muse, Web fonts are not correctly displayed. However, in preview mode, they will display correctly. Is this a bug, any ideas?

  Thanks in advance,

  Mickael the Bomin

  Please try following the steps as in the thread below: -.

  Source without Pro does not display "Design".

• Why I can't get online in safe mode with networking? Does not start in normal mode.

  I can't get my computer starts in normal mode.  It starts only in safe mode.  I can choose the mode safe mode with networking so I can get online, but that's all... just safe mode.  Can I do to solve this problem?  I don't have a lot of money and a new computer is not an option at the present time.  Any help out there?  I have also no sound.  I tried to reinstall my windows xp, but it won't let me.  I have XP Pro and SP3.

  Hello splunk2011,

  Please contact the Microsoft Answers forum with this problem!

  After reading your post, my understanding of the issue is that you are unable to start in Normal Mode and as such, cannot be online within Mode safe mode with networking.

  Because we can start in Mode safe mode with networking, this tells us that a driver or a program from loading at startup may cause the problem.  To solve this, I would try a clean boot.

  More details about this is located at the following link:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  Let us know if this helps solve your problem.

  Best regards

  Matthew_Ha

• Does not open in normal mode

  Firefox will crash whenever I try to open it. Then, it opens in safe mode. I have reset and restarted the computer and it still crashes. I sent more than 127 reports of incidents in December only. I tried to reinstall, but it stops and says that he cannot continue to install. None of my programs that use that the internet will open, I get a "stopped working" or Launcher has stopped working message. (PCMatic, Quicken, Malewarebytes, Superfast PC) and many other programs that I downloaded and uninstalled after that they will not load. Nothing seems to fix the problem

  Short do a clean install of windows and start over I don't know what to try next.
  Betty

  I stopped the hardware acceleration and firefox open in normal mode. My programs still have the problem of launch. (Quicken and PCMatic) when I open them when they try to open I get a launcher has stopped working. I get the same problem with IE as well.
  I'm running the scans suggested right now to search for malware.

• my computer does that in safe mode, it does not start in normal mode, my Security Center opens not or my updates of the widow.

  Hello

  my computer has stopped working on normal mode. I have to use my computer on safe mode.

  My Security Center lights.

  Windows dates won't turn on.

  I think having a consistency of disk.

  Can someone help me?

  Hello

  1. what exactly happens when you try to start in normal mode?

  2. do you receive any error messages?

  3. don't you make changes to the computer until the problem occurred?

   

  Method 1: Perform a system restore

  To get the procedure perform system restore, open the site mentioned below

  http://windows.microsoft.com/en-US/windows-vista/What-is-System-Restore.

  Method 2: Perform a clean boot in safe mode

  For the procedure to place the computer in a clean boot, open the site mentioned below

  http://support.microsoft.com/kb/929135.

  Note: To set the computer back to start normally, use the step 7 in the same link.

   

• Windows Vista does not work in normal mode

  I use Windows Vista. I tried to start my computer in normal mode. It starts fine, but once my desktop, I can't do anything. If I click on something, there is no answer. If I press Ctrl + Alt + Delete, there is no answer. Now I use my computer on safe mode and that is fine, but I am not able to understand what the problem is.

  Hi Ashwathi,

  1. don't you make changes before the show?

  Looks like some programs non-Microsoft is causing this issue. To discover the program that causes this problem, follow these steps:

  Start your computer in safe mode and turn on the computer to start the boot as follows:
  a. open the article: http://support.microsoft.com/kb/929135
  b. Article, follow "step 1: perform a clean boot" the implementation of these measures will disable all programs not Microsoft currently running on the computer.
  c. check to see if the problem persists.
  d. If the problem does not persist in the boot, it means that some programs non-Microsoft is the source of the problem.
  e. to find the program that is causing the problem, try "step 2: enable half the services" to "step 6: resolve the problem.
  f. Once you find the culprit, check if there is any updates to update or fixes to the program. If you find, install them and check the difference or reinstall the latest program.
  g. Article, follow "step 7: reset the computer to start as usual.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• computer does not start in normal mode

  HP Pavilion dv9000, 32-bit, Windows Vista Home Premium, service pack 2

  The computer was working normally. I connected a HDMI cable to use a larger external monitor (hp w2207h). I did several times without problem. I plugged in the cable, then turned on the external monitor. The screen of the laptop goes immediately black that I turned on the external monitor (not like a normal screen transfer). The external screen has no image. The f4 button did nothing. I turned off the external monitor. All disconnected. I couldn't get a picture on the laptop. Finally, I pushed the power button until the computer turns off. I restarted the computer with no attachments. Power goes to the screen on a black screen. The 'hp invent' logo appears then. Then Microsoft name with the long box with green lines running from left to right. So far, so good, everything seems normal. Then, after a minute or two lines green running, the computer stops and the screen goes black, just at the time must appear the opening of session and password screen. The hard drive light also stops flickering, and all what happens is the fan works and there is a black screen. The computer froze. I let the computer frozen for an hour. Nothing happened. I am able to restart computer in SafeMode (f8), but the screen is filled with columns of red dashes. The computer will not update in safe mode. In addition, a new message is displayed. While running in safe mode, instead of my normal screensaver appearing, a message appears that says "the screen saver can't run because it requires a more recent or compatible with Direct3D video card." I don't know even what is Direct3D. I am grateful for the suggestions or pointers to internal diagnostic programs or free online diagnostic tools links. I also never set up system restore.

  Hi HK-Sheko,

  Looks like your video drivers must be updated for Vista.  You can go to the HP Web site:

  http://h10025.www1.HP.com/ewfrf/wc/softwareList?LC=en&DLC=en&cc=us&OS=228&product=1842189

  Or go to the Web site of the manufacturer of your video card for the latest Vista drivers.

  I hope this helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Windows Exployer will not respond in 'Normal Mode', in 'Safe Mode' or in 'clean boot '. "Fix it" even does not work. How can I fix this problem?

  Windows Explorer does not work in 'normal', in "Safe Mode" Mode or in "clean boot".  Same 'Fix it' does not.  How can I fix this problem?  I have Win 7, 64 bit.  Thank you.

  Hello

  1. do you receive any error messages?
  2 has there been any changes made on the computer before the show?

  Method 1:
  If this solves the problem, you can run check and the (SFC) System File Checker tool. SFC scan would be a system file corrupt on the computer search and replace.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7
  http://support.Microsoft.com/kb/929833

  Method 2:
  If the problem persists, you can create a new user account and check if the problem still persists.

  Create a user account
  http://Windows.Microsoft.com/en-us/Windows7/create-a-user-account

  If the problem is resolved in the new user account, you may have corrupted profile.

  Here is the link for troubleshooting a corrupted profile, you can follow the steps mentioned in the link.

  Difficulty of a corrupted user profile
  http://Windows.Microsoft.com/en-us/Windows7/fix-a-corrupted-user-profile

  Method 3:

  If the problem persists you can scan your computer anti-virus using the Microsoft Safety Scanner.

  Microsoft safety scanner will help us to get rid of software viruses, spyware and other malicious software.

  The Microsoft Security Scanner is a downloadable security tool for free which allows analysis at the application and helps remove viruses, spyware and other malware. It works with your current antivirus software.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.

  Warning: If you run the antivirus program that is infected by the virus scan will get deleted. Therefore, reinstall the program. Also, if files and folders are affected by the virus, while they might even get deleted.
   
  I hope this information helps!