Insight journal workers failing to reach

Similar Questions

• AP fails to reach the controller

  I have a controller 4402 and I try to add a 1200 AP series as the first point of access.

  The controller has 5.2.178 a version of the code and the AP has just been converted from autonomous to lwapp.

  I checked the date and time of the two units, and they are in a few minutes apart.

  Here's what the AP shows when it is start and fails to reach.

  * 16:48:04.012 Apr 13: % 3-CAPWAP-ERRORLOG: go join a capwap controller
  * 16:48:04.000 Apr 13: % CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.3 peer_port: 5246
  * 16:48:04.001 Apr 13: % CAPWAP-5-CHANGED: CAPWAP changed State to
  * 16:48:05.715 Apr 13: % DTLS-5-WARNING: FATAL receipt: alert unknown certificate to 192.168.1.3
  * 16:48:05.715 Apr 13: % 3-CAPWAP-ERRORLOG: incorrect certificate alert received from the peer.
  * 16:48:05.715 Apr 13: % DTLS-5-PEER_DISCONNECT: Peer 192.168.1.3 has closed the connection.
  * 16:48:05.716 Apr 13: % DTLS-5-SEND_ALERT: send WARNING: close notify alert at 192.168.1.3:5246
  * 16:48:05.717 Apr 13: % 3-CAPWAP-ERRORLOG: event white 38 & combination State 3.

  Seth

  Have you used the Cisco Aironet for LWAPP conversion tool.

  in the affirmative.

  Check the installation of the upgrade tool directory and see if it has created a (.csv) file that contains the CSD for the AP. Then manually add in the WLC under Security, then AP policies link.

• NetApp Insight Journal content packs

  Guys,

  I installed the insight journal, and my virtual centres taking data and install vcops. I installed the content to netapp pack, but it doesn't seem to be bringing in my controllers of netapp data. Y at - there a step I'm missing or additional configuration?

  Thank you

  Ryan

  The content of NetApp pack requires ONTAP cluster. If you don't see any data being filled, then I assume that you are running the legacy version. If you want that NetApp to build a content for legacy mode pack then leave a comment on the content of NetApp pack to the Exchange Solution.

• Conversion to the Insight Journal

  A few questions on the conversion of the journal storage to record an overview

  -Is it possible to install Log Insight and start sending newspapers host ESXi insight in the newspaper, but also keep the copy on the local host at the same time?  In other words write each log entry to the local host and Log Insight?

  -What are the caviats to make the change?  I want to ensure that the transition is smooth so that no newspaper is lost, if there is a hitch in the installation program.  Is there a risk here?

  -If you only write newspapers for ESXi hosts to the server log insight, what happens when the log insight server goes down?  Are the default logs rerouted to the local host so that you don't miss info journal by a failure that affects the server logs insight?

  ESX/ESXi supports local and remote syslog. Information on how to configure each are available here: http://kb.vmware.com/kb/2003322. The recommendation is always to set up local syslog and remotely for you sure have a copy of the data. There is no caveat of using syslog remote except a known bug that remote syslog can stop working on some version of ESXi (5.0 and 5.0U1 on each version 5.0 and 5.1 on TCP and UDP). By default, local syslog is always configured, however if the workspace is not configured correctly on the ESXi set host might be lost on reboot. Take a look at the article, it should describe what you need.

• [TimesTen] TT0778: Journal entry failed because the file system is full

  Hello
  
  I use TimesTen_11, in the cache process, I got an error "[TimesTen] TT0778: Journal writing has failed because the file system is full.
  
  Event: during the loading of 6 million records from table Oracle TimesTen to group cache.
  
  Error log:
  
  Command > cache support TT_GROUP_MASTER_DATA group commit all 1024 rows;
  5056: cache fails: error_type = < TimesTen error >, error_code = < 778 >,.
  ERROR_MESSAGE: [TimesTen] TT0778: Journal writing has failed because the file system is full
  The command failed.
  
  The details of my configurations are
  
  DSN
  [ttcache1]
  Driver = * / libtten.so
  Data store = * / ttcache1/ttcache1
  LogDir = * / ttcache1/newspapers
  PermSize = 4047
  TempSize = 3000
  PLSQL = 1
  DatabaseCharacterSet = WE8ISO8859P1
  OracleNetServiceName = TTCACHE
  LogAutoTruncate = 1
  LogBufMB = 164
  LogFileSize = 164
  LogFlushMethod = 0
  LogPurge = 1
  
  
  Environment:
  
  OS - HP - UX
  Size of RAM: 32 GB
  
  Can someone guide me to solve this problem.
  
  Thank you InAdvance.
  Valerie.

  You have configured your control point and logs on the same filesystem / disk:

  Data store = * / ttcache1/ttcache1
  LogDir = * / ttcache1/newspapers

  It's a bad idea in any case (see previous posts of Chris Jenkins), but the error is simply to say that you have run out of disk space on the drive containing the transaction logs. A k /ttcache1 FD must confirm. I guess that your transaction logs is not purged, perhaps a way to bookmark in newspapers is the cause of their outfit. If you are able to connect to the data with ttIsql store, run the command 'ttlogholds of appeal' to see a list of existing bookmarks.

• workers failed when applying the fix SOUL 4428060 on AIX

  Hi friends,
  
  I run adpatch to apply the 4428060 SOUL, but I met errror:
  
  ATTENTION: All workers have failed or are pending:
  
  Impossible: folder pebgperf.sql worker 1
  
  ATTENTION: Fix the worker failed above the Manager to continue.
  
  
  
  How can I find the details of the log where this worker error is written?
  
  
  Thank you very much

  Remove the public synonym create it manually, and then deliver adctrl as shown above.

• whenever I try to send an e-mail via the internet explore the message fails to reach and I get a message saying that outlook windows had stopped working what is the solution for this problem of screen?

  whenever I send a mail via Internet explore, the message fails to pass and I get a saying of window, that microsoft Outlook has stopped working and the system tries to the solution but in vain, no resolution, I need your support online

  Hello

  -Did you change on your computer due to which the question has begun?
  -What operating system is installed on your computer?
  -What version of Outlook and Internet Explorer are you using?

  Suggestions for a question on the help forums

• Engine step doesn't fail before reaching its physical limits for the sinusoidal movement

  Hello

  My ultimate goal is to skip a XY (via 2 linear actuators) in a circular motion (radius of 0.47 ") at a frequency of 1 Hz. I run the example VI 'Demo circle' which received my copy of LabView, version 9.0.

  The problem I encounter is that given the physical limitations of the engine and the drive motor, the task should technically be feasible (see calculation *). However, even when the engines are completely discharged (no not attached to anything whatsoever), they start missing steps away from my final goal. I'm only able to reach a radius of 0.2 "(vitesse de pointe de 1.25" / seconde). "

  My question; Is the system set up incorrectly or is my final goal unrealistic, given performance reductions inevitable due to software/hardware?

  I apologize for the naivety of this question, but if there is any information that you may provide which might shed some light on this problem, I would be very happy.

  Possible theories:

  Torque is decreased more at high speeds because of microstep

  A closed loop system would improve performance at high speed

  The VI 'Demo circle' is not the best method to create a circle

  The acceleration is the limiting factor, not speed

  * RADIUS = 0.47 "

  Maximum speed = (RADIUS * 2 * pi) * cos(2 * pi)

  Maximum speed = 2.9 "/ second"

  System:

  LabView v9.0

  PCI-7340

  open loop configuration

  MID-7604

  1 4 a per axis

  10 micro steps

  Linear actuator (form is attached)

  NEMA 17 ordered by motor (sold by ultra-motion).

  Maximum speed of 3.3 inches per second

  1. 2A voltage coil

  1.8º step angle

  Kind regards

  Nick

  Nick-

  I really wonder the max speed in the datasheet.  0,0833 "/ to 3.3" rev / s = about 40RPS (2400 RPM), which is extremely fast for a motor, especially at 24VDC.  Know exactly what engine is on the cylinder and go to www.applied-motion.com and you should be able to find curves of torque for that or a similar engine with various readers.  You will see that couple to 24VDC curves are not good.  In addition, ask Ultramotion if their speed/strength curve is theoretical, or tests have been conducted.

• Insight journal for vCenter

  Given that a single Standard of vCenter license allows bodies 25 - OSI, vCenter Standard for Horizon is also offers this same right?

  Yes. This applies to any package or bundle containing vCenter Server Standard, Enterprise or Enterprise Plus. You should see log Insight 3.3.1 download available in https://my.vmware.com/web/vmware/info?slug=desktop_end_user_computing/vmware_horizon_with_view/6_0

• Default Destination Hostname of Agent Insight Insight of 3.3 Journal log

  Open a default Destination Hostname session prepares the officer of the 3.3 Insight Insight journal to "lol.eng.vmware.com" for me. 3.0 it used to LOGINSIGHT as a default value. Is - is this expected? I find annoying because I now have to write a script to set the configuration defaults to...

  Note: doesn't happen until AFTER that deployment began or joined.

  Yes today ' today - support for logging to self-determination is planned for a future release.

• Configuration of log Insight 3.3.2

  I have deploy the Insight of the FVO journal template and begin after VM. In the VM console, I see below

  I can't connect to this URL - WEB server not started.

  Why the Insight journal unit reported as VMware vCenter Server Appliance?

  

  Thank you

  Ales

  Right, so I think that I thought about it.

  The first start-up, it configures LogInsight and takes you to the login screen. If you Alt - F2 for the operating screen, it shows VCSA.

  If you do anything EITHER at this stage, it seems to stop the process, and the installation seems to be stuffed.

  Should that happen, it's just leave it sitting there on the login screen for some time, after which it then displays portfolio Insight journal screen.

  There is still some configuration in the background, until it reaches this point.

  So I hope this helps someone in the future that is facing this problem

  M.

• Replace the certificate SSL of Insight Log with a CA signed cert

  I'm trying to generate a cert for Insight Log using the method described in this blog post (below) using an automated batch file

  http://www.derekseaman.com/2012/09/VMware-vCenter-51-installation-part-2.html

  The chain.pem file resulting includes my cert and chain cert CA.  When I try to add to the Insight Journal, it is said that the cert is invalid.  Is that you guys can provide suggestions on how to change this piece of lot code to use Log Insight?  The meat of the lot is listed below (I just left aside all the variables that are defined in advance)

  CD /d %Cert_Path%\loginsight

  % OpenSSL_BIN % genrsa 2048 > rui.key

  % OpenSSL_BIN % req-out rui.csr - rui.key - new config key - loginsight.cfg

  Certreq-submit - q - f config "% nom_autorite_de_certification %" attrib-"CertificateTemplate: % Cert_Template % ' rui.csr rui.crt

  % OpenSSL_BIN % pkcs12-export - in rui.crt - inkey rui.key - certfile % CA_Cert_Chain % - name rui-out rui.pem

  copy/b rui.crt + % CA_Cert_Chain % chain.pem

  You must have a file that contains the key and the string, otherwise you will get an error. This command:

  % OpenSSL_BIN % pkcs12-export - in rui.crt - inkey rui.key - certfile % CA_Cert_Chain % - name rui-out rui.pem

  Creates a file, but rui.pem is incorrect. It is actually creating a rui.pfx (see at the bottom of this link: The Most Common orders OpenSSL). I think the problem is that you have the - flag of knots at the end of the command (see what is the purpose - nodes in the openssl argument? - Stack Overflow). A visual way to check is to open the .pem and ensure one contains a section – BEGIN RSA PRIVATE KEY. The chain.pem does not work and the rui.pem is binary, because these two will fail. I hope this helps!

• I want to re - send a message exactly as it was originally (it failed to achieve its goal). I can do this in Thunderbird?

  I send messages that require a response to send to the entire list of CC. If the message fails to reach the recipient target (unknown cause and nothing to do with Mozilla TB) I always have a copy and can of course she Fwd. But then the ease of reply to all does not work for my correspondent receives the sent copy. In MS Outlook, it is possible to re - send a message to exactly the same conditions as the original. Why not in Thunderbird? Or am I missing something?

  How about Message. Change as new? Or do a right click, then Change As New.

• How to install Vista SP1 after that 947366 troubleshooting has failed?

  I have Vista Home Premium 32-bit. I want to install SP1 (and, eventually, SP2 before the April deadline, deadline of 2010). I tried the "Windows Update" - it did not work. I downloaded the installation manual - it did not work. I tried searching for an answer in the forum "Install Vista, upgrade and Acivate", and Mick Murphy (Microsoft Partner) referred me to this forum, the forum "Windows Update". This is probably the right forum to deal with SP1 installation problems vis a vis Vista. Could someone please offer some advice on what would be my next step in the installation of Vista SP1 32-bit? To be more precise on the substantive contribution: I met this http://go.microsoft.com/fwlink/?LinkId=101139link, which redirects to this link http://support.microsoft.com/kb/947366and this link 947366 is where I went through resolution 1 to 4 of the resolution in a vain attempt to get SP1 installed on my computer. In other words, I've tried every resolution 1, 2, 3 and 4 and each result is a pop-up window evoking me the 101139 link. ATER each resolution has failed, I reached the bottom of 4 resolution follows her where:

  Note If the problem is not resolved, this content cannot help you. So, you might want to visit the Microsoft Web site at the following address:

  http://support.Microsoft.com/contactus
   
  which of course makes back off the screen of troubleshooting altogether. I tried to call Microsoft and their lines are busy all the time. I hope that someone else has experienced this similar problem. I did much research on Google, nothing helps. I hope someone in "Microsoft answers" can provide a response to my "question of Microsoft." Again, my question is: what should I do to get SP1 is installed if resolution 1 to 4 of the resolution at this link http://support.microsoft.com/kb/947366 failed? The above is the most accurate description of the problem that I can provide, including the specific error codes and I have already taken measures. Please please please help!
   
  Thank you!

  Paulbyl,
  I suggest that you first run the disk error check and make sure your player is no problem.  Then, run the System File Checker to check for problems with the system files.  If he can find and correct and rerun the System Update tool .  At this point, you must perform a clean boot , and then try to start the installation of stand alone for SP1.

  If SFC finds issues it cannot fix you will need to perform an inplace of Vista upgrade.  Follow the steps described in this article.

  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• PS4000 firmware update failed

  The event ID: 30.4.1 table firmware version V6.0.11 for 7.0.1 update failed. Reason: Another copy of the update is already running. .

  I'm moving to 6.0.11 to 7.0.1, so I can add my new ps6100 to the group.  FTP seems to happen when I do the mistletoe group management.  But when it gets to step 2 from upgrade fails before reaching 1%

  My other set ps4000 up-to-date without problem.

  Any thoughts?

  Gift of greetings,

  This problem has been resolved.   It was a problem with the controller, the controller had been for more than 500 + days.  This support has me initiate a reboot on the controller, once it was full, I ran the upgrade to 7.0.1 of the other controller without problem.  Then I switch to 7.1.5 to match new hardware, I install and when new material is attached to the group I will switch to the current 7.1.X

  Thanks for the help