install software failures on cRIO 9067

Similar Questions

• cRIO 9067 to hired 7fh USB RS232

  Hello

  I have a cRIO 9067 and would like to interface with an instrument that has a converter USB-RS232 from SiLabs.  I can't comminicate with this instrument easily on a Windows PC.  I am able to see the device in MAX when its the cRIO connection.  IT appears under "Devices and Interfaces" as "USB0::0x1FB9:0 x 0100: 121A00A:RAW ' with model number and description of the device.

  I followed the description at this link, but I don't get a ttyUSB # devices.

  https://decibel.NI.com/content/docs/doc-34827

  Is it possible to get this working on the cRIO as a serial port?

  Thank you.

  After some research, talk with people, NOR google and to talk with people to lakeshore.com (provider of the device) this is what I have reconstitute on how to make this work:

  • Under Linux, usb devices are listed automatically, and by default, will appear as a USB RAW device
  
  
  • Once the USB device has been identified, it can then subsequently be linked to a driver
  
  
  • Linux determines if and when to link each device USB-based device Vendor ID (VID) and the model identifier (MID). It is usually 3-4 digit hex string.
  
  
  • In the case of the Lakeshore 121 power source, VID = MID 1FB9 = 100.       I could see in MAX for the Raw Device USB.
  
  
  • There are two levels of USB-serial device drivers. The first pilot: usbserial.ko is a generic driver that handles all USB-serial devices. This should be loaded for any USB-serial converter.
  
  
  • The second driver is specific to the chipset for the USB-serial device.       For the cRIO, there are three options which are pre-installed (DFT, 7fh and a few others)
  
  
  • The drivers can be found at /lib/modules/3.2.35-rt52-2.0.0f0/kernel/drivers/usb/serial/ (where the kernel version directory may vary)
  
  
  • Lakeshore 121 uses the TR labs CP210x chipset, so we chose this one.
  
  
  • Records of the device first of all need to be loaded by Linux. Linux can automatically do this by adding files of length zero in the module.autoload.d directory. To do this run the following:
  
  
  • CD /etc/modules.autoload.d
  
  
  • Touch usbserial
  
  
  • Touch cp210x
  
  
  • restart cRIO
  
  
  • run dmseg. grep usbserial to confirm that usbserial driver is responsible
  
  
  • run the dmesg | grep cp201x to confirm that the driver for cp210x is loaded
  
  
  • The next step is to associate the cp210x of our device USB device driver. Don't forget that linux associate unit to a pilot from the VID and moy. anyone installed linux cRIO base, I'm sure, knew nothing of the VID 121 Lakeshore and MID.
  
  
  • Lakeshore recommended to read the source code for cp210x, adding the VID and MID to the list of recognized devices, recompile the cp210x.ko file and install it on the cRIO. It would work, but it is beyond my current Linux capacity.
  
  
  • Linux offers the possibility to dynamically add MID, VID, so that a device can be recognized on the fly
  
  
  • When the driver CP210x is loaded, a struchture of the entire directory is created. There is a file because the directory structure called new_id where you can dynamically added VID, mid
  
  
  • Create a startup script to run the following command. Be aware of the problems of termination of cr/lf line between operating systems. It is generally easier to create the script on the cRIO with the VI editor to avoid any problems.
  
  
  • echo 1FB9 100 > / sys/bus/usb-serial/drivers/cp210x/new_id
  
  
  • Startup script Info: https://decibel.ni.com/content/docs/DOC-38960
  
  
  • Now, restart (or running the script), you will get a device/dev/ttyUSB [0-9]
  
  
  • Unfortunately, the creation of default of the unit ttyUSB [0-9] does not permission to write, so we have need create a UDEV rule to automatically grant writing
  
  
  • Add the following lines of code udef.conf in the folder/etc/udev

  #typical devices

  ttyUSB [0-9] * root: ATS 666

  • Create a file named 99 - ttyUSB.rules in the /etc/udev/rules.d folder
  
  
  • Add this line of code in this file:

  KERNEL == "ttyUSB [0-9]" * ", OWNER ="admin", MODE ="0666""

  • Restart the cRIO. This should be it! It worked for me.

• I m using ipad mini I got the app store update message about garageband 2.1.1 and I hv software download full GarageBand via itunes, but cannot be installed software bcz itunes sync error

  I m using ipad mini I got the app store update message about garageband 2.1.1 and I hv software download full GarageBand via itunes, but cannot be installed software bcz itunes sync error

  Try to reset the App Store:

  Close the App Store completely from the window of the selector app by double clicking the Home button and slide up the App Store preview pane until it disappears from the display. Then sign out of the iTunes Store (in the settings).

  Then perform a forced reboot. Hold down the Home and Sleep/Wake buttons simultaneously for about 15-20 seconds, until the Apple logo appears.

  Then reconnect to the iTunes Store.

  Also try by going to settings > general > Restrictions > and make sure that iTunes Store, Apps install, delete the Apps and In - App purchases are all under the section allow. Try to install again.

• Is it possible to connect my Mac mini to my Mac Pro laptop using the memory on my mac mini for installing software Ableton as I don't have 3 GB available on my Mac Pro.

  Is it possible to connect my Mac mini to my Mac Pro laptop using the memory on my mac mini for installing software Ableton as I don't have 3 GB available on my Mac Pro.

  I want to download Ableton software, but it requires 3 GB of free memory that I have available on my MacPro laptop not because most of it is used for my library of music because I'm a DJ.

  I'm not sure how I can do it or not at all.

  Thank you very much.

  1. a Mac Pro is not a laptop. Its a big desktop computer.  You probably have a MacBook Pro, which is a laptop.

  2. No, you cannot share the memory (live RAM) or storage (disk space, which is not memory) like that between computers.

  However, it is very very bad practice to have so little storage space available for your computer.   If you have less than 3 GB, you should seriously consider an external drive. and unload some files on the outside. Its best not to leave your hard drive to go below 10 GB of free space because it can seriously affect your computer's performance.

• How can I install software on a disc for an iMac 17 "2006

  I have a 17 "iMac Core duo 2.0 end of 2006 model A1208 (EMC2114)

  The hard drive does not so I replaced it with a Seagate 320 GB Firmware RP13

  I also upgraded the RAM to 4 GB DDR 2 665 years.

  In the diagnosis of the disk utility window, I checked all the components, optical drive, ram etc, all looks fine.

  Whenever I try to install OSX 10.5 software all that he says; Mac OS x cannot install software on this computer

  Then I go into disk utility formatted the disk, I tried Fat32 and journaled Mac

  In both cases, all I get is the option of disk utility.

  I tried to install 10.3 or 10.4 but with both of them, he never read the DVD

  I went on this loop has dozed times, I also tried the option key or command in fact all of the options that I could online, none of them gave me different results.

  I don't have the diskettes of origin provided with the computer as it was given to me.

  Thanks in advance

  If you use gray installation disks from another computer, it will not work. You shoukd probably get a detail of disk in Snow Leopard http://www.apple.com/shop/product/MC573Z/A/mac-os-x-106-snow-leopard

  You can use disk utility to partition as 1 partition using the GUID partition scheme and format as Mac OS Extended journaled. Then install OS X and update using software update.

• error when trying ot read more large block memory on cRIO 9067 LVRT 2014

  I get error "-2147220623" when you run the following code on a cRIO 9067. It works on the cRIO 9074

  

  
  

• Support for LabVIEW 2014 and CanOPEN cRIO-9067

  Hello

  We have NEITHER 9881 CANOpen communication module and cRIO-9067.

  According to the NI 9881 product description page the module should work with cRIO-9067. However, does not support the latest NOR-Industrial Communications for CANopen 1.0.3 2014 LabVIEW and NI RIO 14.0. This means that we cannot use cRIO-9067, can we? If so, when the next version of the pilot will be available? It will work with the cRIO-9030?

  Thank you in advance,

  Nikita.

  Hi Nikita,

  I wanted to let you know that support for the cRIO-9067 is available: http://www.ni.com/download/ni-industrial-communications-for-canopen-14.5/5234/en/

  Thank you!

• Same code compiled for the cRIO-9074, but reports no diagram component calendar violation for cRIO-9067

  Hi, just got my new cRIO-9067. I have converted my project over the cRIO-9067 since the cRIO 9074. Same layout module, same engine, same scan code custom fpga, (hybrid mode).  I have no problem of compilation for the 9074, which is a lower performance FPGA architecting the 9067 FPGA.

  The final timetable for windows compilation shows that the timing is respected for all clocks - 40, 80 and 120 MHz (I use a clock derived for some code sctl). During the end of compilation, during the phase of gen bitfile, I get the dreaded time violation. Investigation of the breach indicates that it is not the custom code, it is not schema components. One of them seems to be linked to the card series OR 9870 I in the chassis.

  Why? Is there anything I can try with the compiler directives for this problem? You would think that it would be easier to compile for the highest performance FPGAS...

  OK, don't ask me how I thought this output - to run I changed nothing else than this: feed the I/O node a reference FPGA of e/s instead of configure the node via the menu "link to. It makes no sense, but the compilation succeeded when I did this.

  I know it is because I created a very simple test VI in my project and made sure it does not compile without it.

• How to restrict users to install software on XP pro

  I want to know how to prevent users from installing software on our PC. I watched security policies, but it was not completely clear how to proceed. Where can I find the good ploicy of change?

  can install only Administrator/s.

  configure accounts log no administrator for them

  password protect the admin log - on.

• Cannot install software — get the error code 1618

  I install software error code 1618 already running when I try to install software.  There is not any other system running.  However, when I look at taskmgr, I see 2 instances of msiexec running.  I was advised to cancel their but they restart immediately.  Any ideas?  Thank you.

  Hi Horselover,

  Thanks for posting in the Microsoft community! You have reached the right forum for your question.

  You did changes to the computer before the show?

  Method 1
  I suggest you to restart the computer, and then perform the clean boot and install the programs and see if that helps.

  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353
  Note: Make sure that you reset the computer back to normal once the diagnosis is complete.

  Method 2
  I suggest you try the steps from the following link:

  Problems installing and uninstalling programs on Windows computers
  http://support.Microsoft.com/kb/2438651#reso3

  Hope this information is helpful and let us know if you need more assistance. We will be happy to help.

• can ' t install software say Symantec LC firewall base overall.

  I can ' t install software say Symantec LC firewall base overall. "

  Hello

  · What is you receive the exact error message?

  You may need to contact Norton to check the firewall settings. You can check: http://community.norton.com/norton/?category.id=nis

• Try to use/install software camera Canon on WinXP Pro

  I have windows XP Professional on my computer and today installed software camera Canon IXUS117HS on it, unfortunately, whenever I connect the camera via the USB port it will fail to recognize the 'Canon Utilities CameraWindow DC' software to upload photos to the ZoomBrowser EX software sister so I can change it, print, e-mail, etc. It produces a message error, says that he has to close and to tell microsoft about this problem.   I spent over an hour with supported Canon, who refused to ring me back (0844 number) and when I rang back after having tried various USB ports, various uninstals and restalls and download a patch for a 115HS camera having unsuccessfully - said it was my fault for registry and windows and called Microsoft.  Can anyone suggest what wrong here please?  I have no trouble seeing the photos in windows imaging and the format of my photos and the SoomBrowser them picks up automatically but the Camera Window DC software just doesn't work.  Summer of back to the store and got another set of software disks but still the same.    Can someone help me, ripping my hair out to had dealing with this every day now.

  DodiRW

  Dear Marilyn

  I'm not completely computer literate and so on to reading your response, I called a friend who is a guru and he said that you had gone to a lot of trouble and gave very good advice, but also, it considered that - to my skill level - you could go down a very dark road - while he was in agreement with me that I must forget just the Canon software , which is rubbish because he should have had these 'libraries' in the software to set my computer as I downloaded it and just use Microsoft software to process photos on the camera, he believes.

  I will thank you to go to so much trouble to find a solution for me - it is much appreciated.

  DodiRW

• I did not use my PC for a while and have forgotten my user name and password. It is now necessary for me to install software on this PC, but need to log-in to do this

  Original title: Log-in question

  I did not use my PC for a while and have forgotten my user name and password.  It is now necessary for me to install software on this PC, but need to log-in to do this.  How can I better log-int?

  The software is now located on my desktop but cannot be put to use; apparently because it is not installed in a suitable place in my computer.  Using the Guest login does not work since the installation of this software is not allowed in the comments section.  Your ideas will be appreciated.

  Hello

  What account are you connected to? Administrator or guest account?

  See the following article: Microsoft's strategy concerning lost or forgotten passwords

• Install software (games, etc.) doesn't show is not in the Add/Remove Programs Control Panel. Vista Home Basic, 32-bit.

  Vista Home Basic, 32-bit. Install software (games, etc.) does not not in Control Panel Add/Remove programs or CCleaner RevoUninstaller. They use all to. I don't know what has changed. Nothing new has been installed. How can I remove the software I want to uninstall? Thanks for your help.

  Hi il898,

  This can also occur if the installation files are broken or missing for the program which may be reason for the program does not appear in uninstall a program from the list.

  I suggest that you run the program to install the program again and check if you get an option to uninstall the program and try to uninstall the program.
  If it still does not uninstall the program, and then try to reinstall the program and uninstall afterwards.

  I hope this helps!

  Halima S - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• The pc seems to have gone to a previous set point during the boot, but now she can not install software and doesn't seem to have Norton AV more

  My daughter's office got fried during the last storm, even though she had a surge protector.  Obviously the power company line was bad.  The pc seems to have gone to a previous set point during the boot, but now she can not install software and doesn't seem to have Norton AV more.  When she tries to run a system restore it gets "extended attributes are incompatible."..: thank you for your help.  Debbie

  Hello

  I would suggest trying the following methods and check if it helps.

  Method 1:

  Run the scan tool (SFC) System File Checker and check if it helps.

  This problem may occur if a system file is missing or damaged.

  You can refer to the method-the System File Checker tool in the following article:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7: http://support.Microsoft.com/kb/929833

  Method 2:

  Try to clean boot, and then check to see if this helps you.

  How to solve the problem by running the clean boot in Windows 7:
  http://support.Microsoft.com/kb/929135

  Note: Once you have completed troubleshooting, perform the steps in the step 7: to reset the computer as usual.

  Method 3:

  Try the steps in the following Microsoft article and check if it helps.

  Problems installing and uninstalling programs on Windows computers:

  http://support.Microsoft.com/kb/2438651

  Hope the helps of information. Please post back and we do know.