installation does not see the printer when I plug

Similar Questions

• Install HP does not see the printer in network, Windows DOES. Help!

  Hello

  I am trying to add my HP Officejet k8600dn to Windows 7 (32 bit) so I can scan, but the HP Installer (add device) can not see the printer. The unit is set up by cable to a switch on my network via an ethernet cable. If I go into the menu "Add a printer" Windows, I can install the printer very well. But I have to be able to scan and I don't know what to do.

  Tips on getting functional analysis if the HP software is unable to see my printer? Subnet mask and gateway on the printer are the same for the computer and the printer. I typed the correct IP address in the "Add a device" menu of HP, but he sees not just it. ARRGG!

  Thanks for any help!

  Hello

  I think that there is some confusion because the Officejet k8600dn is only a printer, it is not a multifunction device and does not provide the capability of scanning.

  You can find the specifications below:

  http://support.HP.com/us-en/document/c01287217

  If you have any different model printer, please specify the exact model.

  Kind regards

  Shlomi

• Windows does not recognize my printer when I plug the USB

  I recently had my computer repaired of malware/virus/faulty software issues, and now the printer that had formerly been installed is no longer recognized. It is not in the Panel and plug/unplug the USB does nothing. I don't know where my printer CD is, as I was not the person who originally installed this unit (I'm the kind of office it's guy, with very little knowledge, as you can see).

  Any help with this problem would be greatly appreciated. Thank you.

  Most often when a device does not work, it is because the driver is damaged. Re-install a new copy should help

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly? SignedIn = 1

  http://captaindbg.com/how-to-update-drivers-on-Windows-7/   (also works on Windows 8)

• The computer does not see the printer (4200 Officetjet) after downloading the driver full features

  Officetjet 4215xi, Windows 7-64.

  Try to use the original HP CD-ROM driver was unsuccessfil, message telling him did not meet the requirements.  Then, I chose to install the driver directly from Windows 7.

  After installing that shows to be successful (the impressions of the printer), I wanted to get the center of HP solutions on the computer and I downsloaded the driver, choose Officetjet 4210 (4215 wasn't a choice available).

  It seems that the installation has been done, there is an icon on the desktop but when clincking it says that the printer is not connected.

  I unplug the USB cable, restart the computer and replugged the USB at the back of the printer.  No results.

  How can I work around this problem.  Thanks in advance.

  Hello

  The HP Officejet 4615xy is no longer included with the full functionality of feature for Windows 7.

  Any driver you may have used is not intended for your printer and not detect...

  You can find the information for your printer below:

  http://support.HP.com/us-en/document/c01796879

  I'm afraid that plenty of advanced features as the HP solution Center is not available for the operating system...

  Shlomi

• Photosmart 5510 MacBook Pro with OS 10.9 does not see the printer on the network

  Continues to give the error message that the printer is offline... in the process of installing it says successful implemented, but impossible to find the printer on the network... I has not changed anything, unless there was an automatic update done some part/sometimes recently... it was working fine.  The self-test on the printer wireless past everything!  iMac and iPad see & print!

  Please help me!

  Oh, Yes, it appears in the list of devices printer twice: once HP 5510 series when connected by USB, and once as 77 has 267 with everything what unknown IP connection but State... is one that says offline and cannot be found on the network.

  I tried all the steps listed in the proposals of the forum without success.

  Hi msdok,

  I understand that the printer is appearing offline even if you can print from the iPad and iMac. I see your message that you have already done some troubleshooting, but I'm not sure what you tried. I recommend using the steps below if you don't have it already.

  Reset the printing system

  1. Click on the Apple icon ( ), then click on System Preferences.

• OJ 8500 A910 Pro - iPhone does not see the printer on the network?

  I have my HP OfficeJet Pro 8500 A910 connected to my wireless network.  The printer found the network and now has an IP address.  My iPhone is also connected to the wireless network.  I can see both devices on the router.

  When I walked into photos and try to print a photo, he says to choose a printer.  When I click on choose, I get "No Printers Found.

  Any thoughts?

  Hey k9rescue!

  Sorry to hear that you are having a problem with AirPrint. What iOS version are you running? And what iPhone model do you have?

  Additionally, if you are unsure that your device supports AirPrint, try to turn your bluetooth off and see if the printer appears.

  Let me know if it helps!

• Samsung S5 does not see the printer wireless

  I just bought this printer last night, I put in place using a laptop that sits on the wireless network and the laptop connects to the printer very well via wifi.  I downloaded the app HP AIO Remote for android phone went through the setup and when it gets to the point of looking for and finding the printer says that no printers are.  I tried to restart the phone, uninstall and reinstall the application, I tried HP ePrint app and still no luck.  The notebook computer always connects to the printer and my office to connect via USB.  I use the good app?  Is there something that I am missing?  Help, please!

  67SS wrote:

  ....   The notebook computer always connects to the printer and my office to connect via USB.  ....

  Hello

  No, your printer must be on a wireless network WITH the Samsung, otherwise your Samsung can't see. You can use a direct impression, but you need to your printer supports this feature.

  The easiest way: connect your printer to your network home woreless and all devices in your House can share the printer. Moreover, what is your printer?

  Concerning

• OfficeJet 6500 printer a wireless set up correctly, but my laptop does not see the printer.

  E710 OfficeJet 6500 a Plus

  Laptop Dell Windows 7 64 bit version

  The printer is set to work wireless.

  I have the printer set in place.  I could print my wireless test report and have determined "That I have successfully setup my printer wireless."  But when I try to configure the printer on my computer and it asks IP... I give the IP address and it did not recognize the "Can't find printer" looks like I have witnessed this process again and again today.

  I disabled my firewall by following the instructions.

  I used the tool for "troubleshooting your connection to a network printer" stage 5 "

  Then he told me to go to the HP support forum.

  Help, please.

  Thank you

  DB64

  I had charged down the bad print driver.  My printer is a more... years had loaded the wrong printer driver.

• PC does not recognize the ipod when I plug in the USB cord.

  I have an ipod touch, and it will replace my old ipod.  When I plug the USB cord, nothing is recognized by the computer.  It is also not recognize my old ipod when I plug it now.  I have other devices that use a USB cord, and they work as they should.

  Apple told me to check with Security Essentials to see if they are blocking a pilot... I am quite at a loss.  It's the ipod or it is safety, or is it the computer?

  I tried everything on separate computers, and they don't always work.

  Any help is appreciated!

  It is not MSE-you get a warning if it were.  Try another cable or try on another PC.  It sounds like the cable might be the problem if all of a sudden or iPod works.

• ESXi on HP BL460C to EVA SAN, Installer does not see the disk non - ESX(I) Although not

  We have a BL460C with qlogic (QMH2462), talk to an EVA 4400 SAN with LUNS = 1 presented for a boot disk and LUN = 2 for the data store.

  San switch is Silkier, if all the paths are visible.  We have installed ESX 3.5.0 u3 on this blade to the same LUN.  The goal is to support an environment entirely multichannel without interaction of zoning, so far all porous bones have been configured to work fine until we tried ESXi

  When we try to install ESXi 3.5.0 u3 for the same logical unit number, the installer décompacte, starts, appears to find the discs and stops with an error "device cannot find support to write... on the image for.

  Is there a driver/known compatibility issue with the ESXi installation program that prevents installation in a multi-channel environment?

  I don't think that ESXi supports booting from SAN.  This is perhaps where the fuse box is.

  You must use the local storage, or possibly a 1 GB (or more) USB stick to boot from.

  Jase McCarty

  http://www.jasemccarty.com

  Co-author of VMware ESX Essentials in the virtual data center

  (ISBN:1420070274) Auerbach

  _{Please consider awarding points if this post was helpful or appropriate}

• Mac does not see my printer "J611a"?

  Hello

  I have connected my printer to my router (it shows the name of the correct router if I run a config report), but does not see the printer on my Mac (when it is wireless).  Everything works fine if I connect to my Mac with a USB port.

  Any advice would be greatly appreciated.

  Thank you.  Stuart.

  Hi SRJC

  I understand that you cannot set up the printer on the wireless network.

  For me looks that you connect the USB cable from the printer to the router. Generally this method will not work.

  You need to configure the wireless through the printing software and add the printer on Mac.

  Given that the printer works via the USB on the Mac already then you can follow these steps:

  1. Click OK in the Menu bar above and then click Applications .

• Put HP1012 in place. The installation process does not recognize the printer.

  I've made sure the device is on and the usb cable is connected.  Printer worked fine until I needed to reinstall the windows xp operating system.  Now reinstall the printer set up the software does not recognize the printer.  Before reinstalling the operating system, the printer worked great even if it is quite old.  I use the original CD game in the installation process.

  Problem solved.  I plugged the printer into different usb port cable and the computer immediately recognized the printer.  Previously, I had ports different usb, but not the one where he worked.  I have 7 usb ports on this computer, and it seems that one does not work.

• I am trying to install Windows 7, but he does not see the disk partitions and the installation goes to the screen "select the driver to install."

  Device drivers for a Win 7 install on Ubuntu system

  Hello

  I bought a Toshiba Portege M400-S5032 tablet PC reburbished that came with Ubuntu installed.  I am trying to install Windows 7, but he does not see the disk partitions and the installation goes to the screen 'Select the driver to install' with no option. Because it is not find Windows device drivers, I went to the Toshiba site to see if I could download a full game, but I can not...  So, how do you get drivers for Windows can install (or y at - it another way to work around it)?

  Thank you!

  The bios on fail safe defaults options are?

  It will probably take the raid driver

• While trying to install XP Pro on T60 he does not see the hard drive, but the fact of the laptop.

  Have a lenovo t60 disk opportunity was wiped out when trying to install XP Pro, I get message windows does not see the hard drive, but he sees the laptop.

  If its SATA you need SATA drivers to install. Since the XP CD doesn't have the SATA drivers on it

  Unless you disable the AHCI in the BIOS. Or their wake.

  Or get the SATA drivers. Check out them on diskette, press F6 during installation and then add them.

• HP Envy 27: Printer does not finish the print job

  Computer is HP Envy 27. Have a for printer HP Officejet Pro 8600 wireless connection. Have old ACER desktop also wireless to the same printer. Print jobs larger than 3 pages, the old ACER works very well, but envy does not. The printer stops after only 3 or 4 or 5 printed pages. Sometimes I hear a small beep in the printer when the printer stops printing. Also the desire does not eliminate the queue when the print job is finished. Entered in the configuration advanced on the computer for printing options and checked to see if that option (not playoff jobs in queue) has been verified. It was not the case. So I don't know why it is keeping the job in the queue. When we first got the urge last year, he had the printing problem, although she probably had the problem of the queue.

  Hello autumnperson1,

  Please download and run the HP print and Scan Doctor www.hp.com/go/tools