OJ 8500 A910 Pro - iPhone does not see the printer on the network?

Similar Questions

• After moving my desktop of my computer does not see the network

  cable tested good, replaced by the new network card it works, actually clicked on the computers in the workgroup to see last week and it worked now missing again... can get online another fine two computers agree, but can not see me

  Hello

  If your router not booking IP use.

  Otherwise, configure the computers with static IP addresses.

  http://www.howtogeek.com/HOWTO/19249/how-to-assign-a-static-IP-address-in-XP-Vista-or-Windows-7/

  Then go to sharing and permissions.

  Maybe this can help.

  Make sure that the software firewall on each computer allows free local traffic. If you use 3rd party Firewall on, Vista/XP Firewall Native should be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq.html#trusted

  Please note that some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  Windows XP file sharing - http://support.microsoft.com/default.aspx?scid=kb;en-us;304040
  Sharing printer XP - http://www.microsoft.com/windowsxp/using/networking/expert/honeycutt_july2.mspx

  Setting Windows native firewall for sharing XP -http://support.microsoft.com/kb/875357

  In Win XP pro you can visually see the setting of authorization/security and configure them according to your preferences.

  http://www.Microsoft.com/windowsxp/using/security/learnmore/AccessControl.mspx#securityTab

  When you have finished the configuration of the system, it is recommended to restart everything the router and all computers involved.

• My Windows Vista computer does not see the network or printers that are connected to a computer using Windows XP

  before that norton was installed, it worked, but since Norton was installed AND DELETED, Vista will not see XP or its printers.

  I have checked the firewall and they took two computers, but still no luck.

  Hello

  Did you change your computer?

  This problem occurs if the (LLTD) link layer topology discovery Responder component is not installed on the Windows XP computer.

  Network card in Windows Vista makes network diagrams of connections between network devices that can be used to troubleshoot connectivity issues. Network map uses a discovery protocol called Link-Layer Topology LLTD (Discovery) that queries other devices on the network to determine how the network is organized.

  Windows Vista includes the software components that implement the LLTD protocol. For other devices on the network to display on the map, they must activate a discovery protocol that can meet the demands of mapping from the Windows Vista-based computer.

  I suggest you to install the update on windows XP.

  http://www.Microsoft.com/download/en/details.aspx?amp;amp;amp;displaylang=en&ID=5577

  This reference so

  http://TechNet.Microsoft.com/en-us/library/bb727037.aspx

• While trying to install XP Pro on T60 he does not see the hard drive, but the fact of the laptop.

  Have a lenovo t60 disk opportunity was wiped out when trying to install XP Pro, I get message windows does not see the hard drive, but he sees the laptop.

  If its SATA you need SATA drivers to install. Since the XP CD doesn't have the SATA drivers on it

  Unless you disable the AHCI in the BIOS. Or their wake.

  Or get the SATA drivers. Check out them on diskette, press F6 during installation and then add them.

• LR does not see the iPhone 6, but used for

  Running on Macbook/Yosemite LR4. Allows you to import photos via iPhone wire 6. Now LR does not see the phone. Recently upgraded to OS Mavericks - is this the cause of the problem?

  OK-went back to the beginning, the disconnect, restart, etc., and now it works.

  Regardless of the question

• system does not see the hard drives as P6000 Windows 7 Pro 64-bit

  PC is a little more than a year. About 2 months after installation disk c crashed. Replaced HP drive.

  Customer said that she had problems starting and kept restarting. He ran chkdsk and hooked up to 36%

  Now the system does not see the drive, but he sees no RAM, etc.

  Anyone know what causes this?

  Can what information I give to help troubleshooting?

  Thank you!

  Hello:

  Try resetting the CMOS.

  If this does not work, I would say that the drive controller in the motherboard is dead.

  Clearing CMOS

• Version 38.0.1 does not see the passwords stored in previous versions

  Version 38.0.1 does not see the previously saved passwords, and urged it to re - enter and save the password. After revert you to the version saved 31.7.0 pass back too. We have more than hundreds of copies of the program and all cached passwords, users do not even know what their password. This failure is a serious problem.

  Problem solved. Probably the file has been corrupted signons3.txt. I deleted the file, and the new passwords are kept. After this version of the software update and new version I've seen passwords, create a logins.json file and now everything is fine. On all other computers in the company such a problem does not arise.

• my iphone 5 s has been disabled. I'm trying to restore my iphone with itunes and itunes asks me to put the password for my iphone. but my iphone does not display the unlock screen. What should I do now?

  my iphone 5 s has been disabled. I'm trying to restore my iphone with itunes and itunes asks me to put the password for my iphone. but my iphone does not display the unlock screen. What should I do now?

  Hello

  Follow the instructions here:

  If you have forgotten the password for your iPhone, iPad or iPod touch, or your device is disabled - Apple supports

• Connected to but the Airport utility does not see the time capsules

  Hi, I have several time capsules.

  I can connect to the web, but the airport utility does not see the time capsules.  I tried to restart the time capsules, router, computer, but I still don't see any of the devices on the network.

  What now?

  Have you tried the airport utility in the iOS version... Download on the App or iTunes store and load... Works better than the Mac version.

  Other than what Mac running what OS do you use?

  This modem you have and how is the installation of TC on the network.

• Windows 8 does not see the hard drive on the Satellite A200

  Windows 8 does not see the hard drive on the A200.
  How to install it?

  S strange Windows 8 should already contain the HARD drive controller driver to recognize the HARD drive during installation.
  The HARD drive is visible in the BIOS?

  Do you use the original disc from Microsoft of Windows 8?

• Portege A600-138 with Vista 32 bit does not see the computers in the Group Win XP network

  Hello

  My Toshiba Portege A600-138 with Vista Business 32 does not see the computers in the workgroup.
  In our office, the computers are all equipped with Windows XP.

  When I connect my laptop to the Local network, I don't see any neighboring computers in Network Explorer.
  I spent 1 hour and 40 minutes to talk to a specialist Service of Support from Microsoft, and the only way to have access to local machines, we found it had to enter the IP of the computer directly into the computer browser path field.

  I hope you understand what I mean.

  The man said that he had no this problem with non - OEM Windows Vista versions.
  He meant that the problem was with the oem versions of Vista preinstalled on laptops only.
  He said that probably the sellers - in my particular case Toshiba - supplied their notebooks with VIsta oem images that were somehow corrupt.

  Does anyone have an idea of the cause of this problem?

  > The man said that he had no this problem with non - OEM Windows Vista versions.
  > It meant that the problem was with the oem versions of Vista preinstalled on laptops only.

  That's nonsense for me
  The Vista OS preinstalled Toshiba which is same BONE as full Vista disc from Microsoft.
  There is only one difference; Toshiba laptops are preinstalled with Toshiba and pilots tools and drivers and tools are part of the Toshiba recovery image that contains Vista, driver and tools

  Check this box:
  http://www.Computerworld.com/s/article/9019179/Teach_XP_and_Vista_to_play_nice_on_networks?taxono myId = 16 & pageNumber = 1

  You will find information that a problem has to do with the new Windows Vista network map.
  Windows Vista uses a new Protocol (Link Layer Topology Discovery).
  LLTD is integrated with Windows Vista, this is why they appear correctly in the network map.
  But the problem is that LLTD is not integrated with Windows XP, which is why they do not appear correctly.

  But you can fix the problem by downloading and installing the layer topology discovery responder.
  Install it and your PC Windows XP will appear on the network map.

• I just installed an SSD on my imac 24 inch 2007 but at the start of the computer does not see the drive. How to use the terminal to look for? Thank you

  I just installed an SSD on my imac 24 inch 2007 but at the start of the computer does not see the drive. How to use the terminal to look for? Thank you

  Can she be seen by disk utility (and which version of Mac OS X is)

• Hello! I restored my iPhone 5 because IOS 9.2 does not work well, and now the IPhone does not recognize the SIM CARD ☹️ please someone help me! What can I do?

  Hello!! Recently, I have restored my iPhone 5 because IOS 9.2 does not work well. But now my iPhone does not recognize the SIM CARD.

  I Don' t know what to do, help me please

  You get an error message?

  What did he say?

• MAX does not see the devices and interfaces

  Hello

  Just got a laptop computer to support the lab and installed Labview. For reasons that I don't have understands THAT MAX does not see the com and USB ports in the laptop. The IT Department gacve my rights to admin ID. Any ideas what's happening?

  Kind regards

  Kaspar

  Dennis, as usual, is correct.  Please check if you have installed NI-VISA.  There is an article in the knowledge base on the way in which com ports are not in MAX unless NI-VISA is installed.  The link to this article is below.

  http://digital.NI.com/public.nsf/allkb/1FAB687036A2D85B862571490072307A?OpenDocument

• Mac does not see my printer "J611a"?

  Hello

  I have connected my printer to my router (it shows the name of the correct router if I run a config report), but does not see the printer on my Mac (when it is wireless).  Everything works fine if I connect to my Mac with a USB port.

  Any advice would be greatly appreciated.

  Thank you.  Stuart.

  Hi SRJC

  I understand that you cannot set up the printer on the wireless network.

  For me looks that you connect the USB cable from the printer to the router. Generally this method will not work.

  You need to configure the wireless through the printing software and add the printer on Mac.

  Given that the printer works via the USB on the Mac already then you can follow these steps:

  1. Click OK in the Menu bar above and then click Applications .