Installation network HARD disk does not work

Similar Questions

• Tecra 8000: monitor and the HARD disk does not work - does not start

  I have a laptop Toshiba Tecra 8000 given to me the year last by my uncle. I live in England, but it is and bought the PC in Italy. I do not know if this causes complications, but I thought it may be useful.

  Since I got it it occasionally did not display any image of all system startup, so if I have given some time and restarted it would start working again. Happening of bagan more frequently and now I can't make it work. I have conections and found that everything was in place. Then he doesn't seem to be turning on, however when I replaced the front LED cable seems to be turning on and although I couldn't hear much the CPU was luminous heat. I opened the drive and it gave once more, succeeded him and he still wouldn't start. I had purchased and replaced the screws on the heatsink around this area but I did not handle it with many other things.

  So now, I have a monitor that does not work and a gard drive that won't start... Any ideas?

  Thank you!

  Hello

  Could be either the card mother, CPU or ram. The processor when it goes bad or is not locked in place (have had this before, install the CPU but forgot to turn the lock, so he cannot move) the computer will act as its startup, don't give any error and stay on a black screen. Verify that the processor is locked in place. Then remove the ram and try a stick of RAM that runs on another computer. If you try the RAM and the processor do not always start, then chances are your motherboard is dead and must be replaced. Hope this helps and that solve you the problem.

• How to disable the file hiding (changing options for hard disk does not work)

  Hi all

  I hope someone can help me with the following problem:

  -J' need to open a file of 16 GB of content in third party software (Stata) who reads completely in memory.

  -Due to Windows caching file, necessary to get the procedure done about 32 GB cache files and Stata access physical memory.

  -As I have only 24 GB of physical RAM file is read later part of virtual memory, which leads to serious performance problems.

  I unchecked the box 'Enable write on the device cache' to my hard drive. That did not help. Is there a way to disable the Cache during PLAYBACK of files?

  Thank you very much in advance for any help!

  Tobi

  The write cache and virtual memory are different. Virtual memory is an extension of the physical memory residing on the HARD disk where Windows is installed. Normally, the virtual memory is about twice the size of the current physical memory. Write cache is an exclusive setting for external hard drives only and has no effect in internal hard drives.

  In your case, please note that full 24GO of RAM will not be allocated to the program. At least 1 GB will be reserved for windows, so the rest of the programs are moved to virtual memory, which means that the HARD drive. It is not recommended to disable virtual memory because it can cause stability problems. In addition, the files are not copied directly in memory, even if they are big. Instead, the parts of the file are available and this area, including the incremental values and material, are stored in the memory. So if all of a sudden, you access an area of the file which is very far away from the previous location, it takes time as the new area, as well as differentials and material value of a few bytes is also copied to the memory. The box of files previously displayed is erased from the memory.

  For performance improvements, you can go for the SSD, RAM with higher clock speed (must be compatible with the motherboard) as processor as well as the upgrade. However, please note that the process of accessing a file even as mentioned previously, but the speed will increase because of the higher bandwidth and the clock frequency.

• Windows 7 upgrade failed - disk HARD recovery does not work

  I just received my Windows 7 upgrade disc, followed the procedure and he managed to upgrade Vista 64 bit for Windows 7 32 bit! Some drivers also seem to, were charged more than once.

  I tried to do a system restore from the recovery of HARD drive partition - and it won't!

  Can someone, please?

  Hello

  Drive HARD recovery does not work because Win 7 ran the Boot Manager and maybe the HDD partition has been affected.

  I guess you want to roll back to Vista preinstalled Toshiba.
  I think in your case, only the recovery disc will help you.

  Welcome them

• my hard drive does not work, I can not download my antivirous

  my hard drive does not work, I can not download my antivirous

  Here are a few articles with possible solutions and its fix for the hard drive problems.  Maybe at least will help any problems you encounter.  I could have provided more targeted recommendations if you had provided more information about what the problem is exactly, when he started, the manufacturer, make and model of drive, how the player does not work - is that it recognized by the system, it appears in Windows Explorerr, the door opens when you press the button...  If the following text does not, provide this and more information about the problem and your configuration maybe we can provide additional assistance.

  Compliments and thanks to the spirit of another thread:

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.microsoft.com/gp/cd_dvd_drive_problems - A Mr Fixit

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  I hope this helps.

  Good luck!

  Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Toshiba canvio 1 TB portable hard drive does not work with windows 8

  The drinking Toshiba Canvio 1 TB hard drive is compatible with Windows 8?

  Hi Michael,

  Welcome to Microsoft Community and we are happy to help you on this question.

  According to the description of the query, the Toshiba Canvio 1 TB portable hard drive does not work on the computer.

  I ask you to answer some question in the context of this question:

  Do you have an error message when you try to access the hard disk on the computer? If Yes, what is the exact error message you get?

  I would like to inform you that the Toshiba Canvio portable hard drive is compatible with Windows 8.

  You can check the link to verify this compatibility with Windows Compatibility Center:

  http://www.microsoft.com/en-us/windows/compatibility/win8/CompatCenter/ProductViewerWithDefaultFilters?TempOsid=win8&Locale=en-us&TextSearch=Toshiba%2Bcanvio%2Bportable%2Bhard%2Bdrive%2B&Type=Both&CurrentPage=0&TotalPages=1&ShowCriteria=0&SortCriteria=Relevance&Compatibility=Unknown&LastRequested=14

  Please answer us with the required information on this issue in order to help you.

  Let us know if you have other Windows related issues.

• For 1000-zx satellite recovery disk does not work

  XP Recovery disk does not work. The 3 options are unresponsive. Is there an easy solution. All other functions of cell phones seem ok. It is a reliable machine for more than 3 years, but now must use the recovery disc. Brilliant ideas greatly appreciated.

  Hello

  Well, I put t know why you recovery CD doesn t work. Have you checked the CD some scratches? Have you tried to clean this CD?
  However if it of impossible to use the recovery CD, you can contact the ASP and buy a new one. It doesn t expensive.
  In addition, you can install an original Windows operating system and then all the Toshiba necessary drivers on the Toshiba site.

  Good bye

• Installation of Windows service does not work after Windows Explorer 9 uninstalling and reinstall Explorer 8

  Installation of Windows service does not work after Explorer 9 uninstallation and reinstallation of 8.  I followed several suggestions on this forum, but still no luck.  I ran the SFC system twice, who told me he had corrupted files.  "Some have been repaired and some might not be."  I then went in the event viewer after a start to the top and he stated that the 'Adobe APM service' is not found.  Also the "hpqddsvc' and the 'gupdate' is not found.  He tries to install something every time I start, but he abandoned.  I checked whether the system is on and disabled.  It's on.  There are a lot of small problems, but my main concern is the Adobe program.  I tried uninstalling and reinstalling Adobe, but still get an error message that the Windows Installer Service could not be accessed. Other suggestions?

  Hello

  I suggest you follow the link and check.

  How to troubleshoot issues that may occur when you install, uninstall, or upgrade one program on a Windows computer

  http://support.Microsoft.com/kb/2438651

• Peer Networking Grouping Service does not work; How can I make it work?

  I use Windows 7 and trying to set up a home network I am unable. After you run the troubleshooter, the only problem is that the Peer Networking Grouping Service does not work. Messages to indicate there is no other problems other than Peer name resolution Protocol (PNRPsvc) Service or the Peer Neetworking Identity Manager (p2pimsvc) Service is not running.

  How can I solve this problem?

  Hello

  First delete the file idstore.sst from the following location: C:\Windows\ServiceProfiles\LocalService\AppData\Roaming\PeerNetworking\idstore.sst and once you remove, restart the service Peer Networking grouping.

  Follow the steps to restart the service:

  a. click Start, type Services.msc in the search box and press enter.

  (b) in the Services window, search for Peer Networking Grouping.

  c. make a right click the service: peer networking grouping and click restart.

  Also, see the following Microsoft articles:

  Establishment of a network domestic:
  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-home-network

  Why can't I create a homegroup? :
  http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-create-a-HomeGroup

  Hope the information is useful.

• Toshiba 1 TB external HARD drive does not work

  I have a 1 to external drive what cards via usb cable, Ive put a lot of multimedia files on it and have been using it without problems don't have nothing put on for a little while, went to look for some files off it and comes up with usb not recognized, put it in another computer and the light comes done hard disk a rattling for a few seconds then hummes just as if it turns While the light stays on and is not all pulse, on the computer, it emits a sound to say ive plugged the on the bottom, it says safely remove hardware.

  Ive tried on two computers when in my computer it does not record.

  PS im not the tool sharper in the hangar when it come to tech stuff.

  The same problem. I bought edition 2015 last fall. It has a power supply problem (electrical problems). I thought it's because of my laptop. He made her crazy, but SMART was ok. Yesterday, it makes noises again and now it does not work. I saw light blue and only a little sound of pcb as start start. I saw that head of player on the Board.
  It's really a defection from the factory.

• Satellite L350-170 - recovery disk does not work

  Hello

  I have a L350-170 running Windows Vista home, I recently buy a Toshiba restore CD and now that it's happened, it does not work.

  I put in the CD and boot from the CD drive, I can hear work and the display shows "Windows loading files" and a bar appears at the bottom of the screen, after that, the screen turns white and all I'm left with is a pointer of the mouse and a black screen.

  Thank you
  Jackie

  Hello

  Have you tested if the laptop would start using another bootable Linux Live CD, WinPE or Win XP disc?
  Please check that would help determine if the problem is related to the computer laptop or recovery disk.

  Please also check if the HARD drive is ok. For this test, you can use a test called Drive Fitness Test free HARD drive tool. Google for it.

  However, it could also be a defective recovery disc and in this case, you should get in touch with the guys where you ordered this drive may be you need a replacement.

• External USB 3.0 HARD drive does not work on USB 3.0 port

  Hello guys,.

  I have a problem with my external HARD drive and the problem is that it is USB 3.0 feature does not work in my computer.

  The curious thing is that it works very well in the SATA port or a normal USB 2.0 port.

  Y at - it a failure with the HARD drive or is there something wrong with my motherboard (M5A99 fx pro r2.0)?

  Thanks in advance.

  From my point of view of the few is not HARD drive problem because the HARD drive operates in a USB 2.0 port.

  I m wondering if you tried to update the USB 3.0 driver.
  Have you tried this HARD disk in another computer / USB 3.0 ports?
  I think that its worth a check.

  Also, I read on some problems of USB 3.0 controller from different manufacturers.
  Sometimes, it might be possible that some problems of compatibility between different devices may arise.

• I'm trying to recover my Windows Vista, but one of my #2 recovery disk does not work... What can I do?

  I copied 2 cd on my hard drive disk recovery & disk #2 does not work. I tried to get through the system recovery to restore the computer to its original factory shipped State. It calls into original form and content reinstalles. Then it restarts to finish and said: ERROR LOADING C:\PROGRAM FILES\WINDOWS MEDIA PLAYER\wmssetup.dll THE SPECIFIC MODULE COULD NOT BE FOUND!

  THEN IT CONTINUES TO THE NEXT WINDOW WHICH SE BED:
  INSTALL WINDOWS
  WINDOWS COULD NOT PARSE OR PROCESS UNATTEND ANSWER FILE FOR [SPECIALIZE]. THE SPECIFIED IN THE ELEMENT OF THE RESPONSE [MICROSOFT-WINDOWS-DEPLOYMENT] FILE.

  AFTER THIS WINDOW IT SAYS PRESS OK BUT MY LAPTOP DOES ME NOT LEAVE THE REST OF THE ARROW IN THE MIDDLE OF THE WINDOW & WON'T LET ME CLICK ON IT! WHAT CAN I DO TO GET THROUGH THIS PROCESS!
  YOUR HELP WOULD BE GREATLY APPECIATED! THXS
                                                    

  Contact the computer manfacturer, who provided the original discs.

• Network adapter driver does not work with the recovery discs provided by hp

  Hello

  My wireless light does not illuminate. The network adapter driver does not install from the recovery of the driver CD.

  Here is the hardware ID. Please provide a link to the drivers:

  PCI\VEN_10EC & DEV_8176 & SUBSYS_1629103C & REV_01

  PCI\VEN_10EC & DEV_8176 & SUBSYS_1629103C

  PCI\VEN_10EC & DEV_8176 & CC_028000

  PCI\VEN_10EC & DEV_8176 & CC_0280

  Thank you

  You are the very welcome.

  It does not sound like a heat problem.

  I don't know a lot about the repair of hardware issues beyond replacement memory and hard drives.

  I could try to clean the area of fan/radiator with a can of compressed air and see if that clears any dust that may accumulate.

  To do this, disconnect the laptop from the AC adapter and remove the battery.

  Insert a rod through the air fan to keep the blades turning when you spray air.

  Spray through the air intake fan and watch to see the dust out of the exhaust.

  Repeat once or twice and blow air from the other direction of the drain line to the fan.

  The other driver, you need is the driver of protection Protectsmart hard.

  See if it works.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-116584-1&cc=us&DLC=en&LC=en&OS=4063&product=5278311&sw_lang=

• External hard drive does not work properly

  Hi all

  It is a slightly different external HARD drive problem.  I had my faithful media ATMT bin since my first laptop with XP (2003) and I bought it in 2005.  It's a little wobbly as the fan vibrates a lot, but this isn't a problem.  What is the problem, is that I have a windows machine 7 who thinks that drive a need to put in shape, but my previous laptop which has vista on it was absolutely no problem to read the files IN ALL and you can open one of them without a hitch.  I tried to run CHKDSK I:\I (it is labeled as the I drive :) and 7 claims that it is in the format RAW.  I had a look at CHKDSK on my old machine and it is in FAT32, I since changed it to NTFS, but seems to have no effect.  I also tried the hunting of the drivers for the external hard drive, but I come only through links to Amazon as these things are always available.

  I really need to access this drive on my current computer as the older one needs a considerable cooling method to make it work therefore the latest machine.  What I also don't understand, it's that it was working absolutely fine on this machine too until quite recently.  He worked on it that I need, but have not been accessed for a while and so solutions in this regard would be greatly appreciated.

  Thank you very much for your time.

  RM

  Your drive has reached its copy by date and it works on time taken (if he is stil)

  If this does not work on another PC then it's probably dead.

  You can try the utility disk SeaTools from Seagate to check and see if it can detect and report on the drive