Installation on the device problem

Similar Questions

• Plustek OpticBook 3600 will not install error that an error occurred during the installation of the device. The required section was not found in the INF

  Original title: Plustek OpticBook 3600 is not installed

  Found new hardware wizard runs, but after scanning stops the disc from the manufacturer with the message ' year error occurred during the installation of the device.»  The required section was not found in the INF"

  PC system is homebuild which, in theory, exceed the minimum requirements of the system of manufacturers.  Operating system is Windows XP Pro with Service Pack 3.  The scanner is connected to the USB 2.0 card that is not separately powered, but installed in the PCI slot.  I suspect that the problem lies in the PC rather than the scanner. but do not know what the problem is.  Any help would be appreciated!

  Hello
  You can try the troubleshooting provided in the link below steps to fix the problem.

  You receive a "unable to install this hardware" or "an error has occurred during installation" error message when you try to install a PCI device

  http://support.Microsoft.com/kb/841567

  Note:

  To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows

  http://support.Microsoft.com/kb/322756

  See also:

  Error message: cannot install hardware. An error occurred during the Installation of the device

  http://support.Microsoft.com/kb/810882

• Cannot install this hardware. An error occurred during the installation of the device

  Can someone please HELP ME - I get the following error message: cannot install this hardware. An error occurred during the installation of the device. They system cannot find the specified file.

  I am not able to connect any hardware. It started all of a sudden. I can't connect my mouse so it before I'm not able to use my computer.  He did the same thing when I put in a USB key, there was the same error message.

  If something is damaged? How can I resolve this - pleaseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee.

  Looks like you may have a virus or other malware. Get your updated antivirus program and start safe mode.  Note that some viruses can hide from your normal antivirus program, so you really need to scan mode without failure.  To enter in Safe Mode when you turn on first, press F8 on every seconds until you get the menu, and then select Safe Mode.  Then run a complete system scan.
  Microsoft has suggestions and offerings to
  http://Windows.Microsoft.com/en-us/Windows7/how-do-I-remove-a-computer-virus
  Moderator Forum Keith has a few suggestions along this line to
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-performance/Windows-Explorer-has-stopped-working/6ab02526-5071-4DCC-895F-d90202bad8b3
  If that suits him fine. If this is not the case, use system restore to go back to an earlier date at the beginning of the problem.  To run system restore, click Start-> programs-> Accessories-> System Tools-> system restore.  Click on the box that says show more restore points.
  You can check the corrupted system files.  Open an administrator command prompt and run SFC if the above does not help. Click START, and then type sfc in the search box, right-click to SFC. EXE, then click on run as administrator. Then from the command prompt, type sfc/scannow.
  Finally if all else fails, you can look at the rather cryptic system event log.  To make, click Start-> Control Panel-> administration-> event viewer tools.  Once in Event Viewer system log-click and scroll entries looking for these "error" with indicator see if you can find guidance on where the problem may be.
   
  I hope this helps.  Good luck.

• Material up to date Assistant, MTP device an error occurred during the installation of the device

  I have a problem installing the driver for my mp3 player. I get this message after I try and install "" there was a problem installing this device: MTP device, is an error occurred during the installation of the device the specified service does not exist as an installed service. "" Even if I uninstall and re install the driver, I still get the same message. What could be the cause of this error message?

  My operating system is Windows XP home

  Original title: update Hardwre Assistant

  Hi D.L.B1,

  • What is the brand and the model number of the MP3 player?
  • Other USB devices are connected to the computer works well?

  You try to manually add the MP3 player to the computer and check if it can help solve you the problem and if the MP3 player is detected.

  You can access the link below and follow the steps in the article to manually add the material to the computer.  When adding the verification of the material if it appears two devices one by one for device MTP and other USB Mass Storage Device. If it shows both, select the USB mass storage device from the list and try to install it and check if that helps.

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/app_start_hardware_wizard.mspx?mfr=true

  If the problem persists and you cannot install the MP3 player, you can contact the manufacturer of MP3 and check if you need to make changes to install it and if they have the latest drivers to install.

  I hope this helps. Let us know the results.

  Thank you and best regards,

   

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Driver VGA Dual-Mode Camera installs but the device does not appear in the list of devices to Windows Photo Gallery

  Driver VGA Dual-Mode Camera installs but the device does not appear in the list of devices to Windows Photo Gallery

  Hello

  I will need to know the brand and model of the device in order to help you solve it.

  You see the device listed in the Control Panel, hardware and sound, scanners and cameras?
  Brent
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• There was a problem installing this card material Ralink Turbo wireless LAN, that an error occurred during the installation of the device. The system cannot find the specified file.

  Opus system Windows XP Edition SP3 eddition family

  I tried to install two NICs - Netgear RangeMax Wireless - N USB 2.0 adapt WN111v2 and PCI Ralink Startech 555WG 801,11 g Wireless PCI Adapter Card. In both applications on the end of the installation I received the message that installation failed.

  I downloaded all the latest drivers, disabled antiwirus program and firewall, I called the software factory. Nothink helped. Everything is pointing to problem windows install the drivers.

  For installation of Netgear USB wireless adapter WN111v2 - after installing software you plug wirelles adapter to the USB port and start the final driver configuration. After that I get message "installation of the client software has failed. Restart your computer and run Setup again.

  Can you help me?

  Hello
  
  Step 1: Adding to the suggestion of A70M1C, you can also check if the problem persists in the clean boot state.
  Reference: http://support.microsoft.com/kb/310353
  
  

  Step 2: Also check if you can find any error message in the event viewer and send back the same.

  Reference:
  http://support.Microsoft.com/kb/308427
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/snap_event_viewer.mspx?mfr=true
  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/event_overview_01.mspx?mfr=true

  Thanks and greetings
  Umesh P - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• HP Deskjet F4180: Installation of the device not complete

  Due to a printer problem, I had to reinstall all my drivers and software and did that on the HP site. However when I went to analyze, the Solution Center always tells me that "the device is not full. I'm no expert, but I've tried everything I can think of. I ran the doctor printing and scanning, the installation wizard. The impression scanning doctor tells me that Device Manager.ok: check.ok Device, device status ok, BUT Solution Center X,

  HP printer test scan OK installation wizard.

  However, when I tried again to do a reinstall of the printer's drivers/software when he asks me to add a device and I try to connect to the printer it does not seem to acknowldge that the printer is here!

  Can anyone help please.

  Thank you

  Gerry

  Hello

  Could you please follow the first link and uninstall all the hp Sw of your system

  http://support.HP.com/us-en/product/HP-DeskJet-F4100-all-in-one-printer-series/3177560/model/3177564/document/c02259020/

  you will need to install the driver of all the features.

  Besides some Hp software require for Flash player, XML, Java, Netframe phaser works and dotnetFx. Please ensure that all the Sw above installed on your system.

• Error occurred during the installation of the device, a service in the INF installation section is not valid with Sansa Fuze player

  Media player 11 fails to connect to my sansa fuze player. A second computer find the fuse in sansa without problem. Default media player 11 , I get the following message: error occurred during the instalation of the device, an installtion of service section in the INF is invalid.  I have two players from sansa and both not on this media 11 computer system, but both work on a second computer with media player 9 ? Is the problem, a bad installation of the media 11 on the first computer system, should remove and reinstall media 11 If I delete what is happening in the music on this computer file. Carl L_942

  Hi, Carl L_942,.

  Connect the Sansa Fuze and put into MSC mode. This enabled the majority of users with this problem. Check if it helps you too.

  For more information, see:

  Activation or forcing MSC mode on the Sansa player

  Additional reference on:

  Check and change the device to the master or the MTP USB mode

  The only problem with Media Player 11 and Sansa device is the synchronization of album art to the device.

  For more information, see:

  File Readme for Windows Media Player 11 for Windows XP

  Kind regards

  Divya R - Microsoft technical support.

• Installation of the device drivers for the Zune 8 GB using Windows Vista SP2 OS

  I try to install the Zune software installed on a laptop Acer of MS Vista with SP2.  The Zune player is a 8 GB model.  The Zune software is installed fine, but when Vista tries to install device drivers, it fails, asking me to contact the hardware vendor.  It is used to work on another computer running MS Windows XP with SP3.

  What can I do to make it work on Vista computer?

  Hi Midnightwreck,

  What is you receive the exact error message?

  Step 1: Examine the Windows Device Manager. To do this, follow these steps:

  (a) click Start, right-click computer, and then click Properties.

  (b) click on Device Manager. Click on the computer root icon and then click on Search the hardware changes in the Actions menu. Zune should be listed under portable devices.

  Note If the player has been incorrectly installed, Zune can be listed with a yellow exclamation point (!). Or, it may be listed under other devices as USB (Universal Serial Bus) device.

  (c) double-click Zune, and then click driver . The current version of the driver that is installed must be 4.2.58.0.

  If the Windows Device Manager indicates a problem with the device, or if the Player version that is installed is not the current version, you must update the driver. To do this, follow these steps:

  1. right click on Zune or a USB device , and then click Properties

  2. click on the tab driver , and then click Uninstall.

  3. If it is displayed, select delete the driver for this device, and then click OK.

  4. click on the computer root icon and then click on Search the hardware changes in the Actions menu.

  5 right click on Zune , and then click Properties

  6. Click tab driver , and then click set to update driver.

  7. click Browse my computer for driver software.

  8. click on Browse, find the program Files\Zune\Drivers folder, and then click OK.

  9. click Next.

  If you are prompted, click install.

  After the driver installation is complete, click close two times.

  Your Zune device is not detected by your computer or the Zune software
  http://support.Microsoft.com/kb/944909

  Step 2: Download and install the latest version of the Zune software, then check if the problem persists.

  You can follow the steps mentioned in the link below

  How to fix errors in the Windows device for the Zune device manager
  http://support.Microsoft.com/kb/953933

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• There was a problem installing HID Non-User Input filter data (KB911895), a fatal error occurred during installation of the device

  I tried to uninstall the faulty data filter & reinstall download (KB911895). all attempts fail & downloads auto continues trying to install "ad noursium". How can I solve this problem please someone? Brian

  Hello

  Step 1: Follow these steps and then try to install the update.

  1. go to the location: c:\windows\system\drivers\
  2. search for and rename the file wdf01000.sys wdf01000.old
  3. restart the computer.

  Step 2:

  Reset windows update components

  http://support.Microsoft.com/kb/971058

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• HP solutions Center can not run because your installation of the device is not full (Windows 7)

  I downloaded and tried to install HP Photosmart C309a all-in-One Driver Software 14.0 Rel.5 in a new installation of Windows 7 Professional (not an upgrade). Installation works very well until the moment of the connection to the printer.

  I tried the wired and wireless network connections. The screen "Found network printers" lists the printer with the correct IP address and MAC address. Network Diagnostics screen shows any errors. The screen "Installation of your printer" poster "Detected printer", then says "printer setup has failed to complete." Retry does not help. Removing and reinstalling the software do not help.

  The Windows devices and printers control panel shows the printer as "Series of HP Photosmart C309a (redirect 2)". I am able to print a Test Page from Windows printer without error. The 'print options' are also available.

  The printer works fine with other computers on my home network, one running XP and a Vista running.

  How can I get the software installation to complete successfully and provide the printer the HP Solutions Center?

  Thanks for your help.

  Well, I have solved my problem. I'm not sure that these steps are necessary, but here's what I did.

  1 follow the instructions in "Completely uninstall and reinstall the HP software" HP. In particular, 'clear the temporary files and folders' and 'Disable Terminate and Stay Resident (TSR) programs and any other lighting programs' before reinstall you, then "Reactivate startup programs", after the reinstallation.

  2. install base drivers, and NOT the complete software package with applications.

  3. If the basic install works, then install ALL the applications (eg Solution Center). Do not try to install some applications but not others.

  4 remove the applications that you do not (e.g., Online Shop).

  Maybe the steps 2-4 are not mandatory, but they worked for me.

• installation of the system problem

  I have an acer aspire one and I did a second system restore because I could have been a victim of software counterfietting. and since then. my laptop has not been able to function. Whenever I try to stop it and turn it back on, he repeats to me Setup starts service. It doesn't let me do anything. In addition to this, the installation program has been from services for about a week now. Does anyone know how to fix this?

  Hello

  This is the guide that you follow to do a restore to factory with an Acer:

  http://Acer.custhelp.com/app/answers/detail/A_ID/2631

  Once you do this you then download the latest drivers for your model on the Acer site:

  http://us.Acer.com/AC/en/us/content/drivers

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  With updates after reinstalling make sure you have the latest Service Packs installed:

  Then download the rest of Windows updates.

  Click Start > right click on computer > left click on properties > see if you have Vista 32 bit or Vista 64-bit installed.

  It will also tell you which SP you have installed.

  Then, choose the download of 'bit' OK to use to install Service Packs, installation of SP1 first if it is not already installed.

  Vista SP1 32-bit (x 86): http://www.microsoft.com/en-us/download/details.aspx?id=30

  Vista SP1 64-bit: http://www.microsoft.com/en-us/download/details.aspx?id=21299

  Vista SP2 32-bit (x 86): http://www.microsoft.com/en-us/download/details.aspx?id=16468

  Vista SP2 64-bit: http://www.microsoft.com/en-us/download/details.aspx?id=17669

  This Information Microsoft can help you resolve problems that you encounter during the installation of Service Packs for Vista.

  http://support.Microsoft.com/kb/947366

  See you soon.

• Photosmart C4795: Solution Center cannot run because your installation of the device is not complete

  Months after HP software reload to correct a mistake, I lost my HP Solution Center during installation.

  Today, I ran the utility HP Print and Scan doctor and downloaded the software to install the HP Solution Center, but the following error message:

  HP solutions Center can not run because your device installation is not complete.

  I want to set up a wireless printer connection.

  Appreciate your help.

  Jean,

  It was quite a process, but everything seems to work well!

  I just rebooted my laptop, and now I have the HP Solution Center!

  The error message that I mentioned in my previous note seems to have disappeared (I hope never to reappear!).

  The question that light that I see is that the HP Support Assistant is always located on my taskbar.  How can I get rid of this?

  I can't thank you enough, John, for all your help and advice!

• Installation with the ID problem

  Hello
  
  I installed IDSServer, IDSShared and IDSClient in version 2.2 on my Windows 7 pc to play with him.
  Because of this I chose http as a queue mechanism.
  
  I would test the installation as described in idsinstall.pdf.
  The server seems to be ok,
  but the test with DSIEXW32.exe client fails with the following debug messages:
  
  C:\docserv > DSIEXW32. EXE
  2011-11-04 12:49:12, 855 DEBUG: dsilib - JVM and classes loaded in DSIInit.
  2011-11-04 12:49:12, 858 DEBUG: dsilib - attached current thread to the JVM in DSIIn
  itInstance.
  2011-11-04 12:49:12, 871 DEBUG: debug - * HTTP properties *.
  2011-11-04 12:49:12, 874 DEBUG: debug - http.reuse.ports = < 15 >
  2011-11-04 12:49:12, 876 DEBUG: debug - http.url = < http://localhost:49152 >
  2011-11-04 12:49:12, 876 DEBUG: debug - marshaller.class = < com.docucorp.messaging
  . data .marshaller .SOAPMIMEDSIMessageMarshaller >
  2011-11-04 12:49:12, 880 DEBUG: debug - *.
  
  2011-11-04 12:49:12, 885 DEBUG: debug - socketArgs [0] = localhost
  2011-11-04 12:49:12, 886 DEBUG: debug - socketArgs [1] = 49152
  2011-11-04 12:49:12, 889 DEBUG: debug - = < localhost > IP address
  2011-11-04 12:49:12, 891 DEBUG: debug - Port = < 49152 >
  2011-11-04 12:49:12, 893 DEBUG: DocucorpMsgUtil - factory of the queue for ' C:\docclnt\
  docclient.XML' is com.docucorp.messaging.http.DSIHTTPMessageQueueFactory
  2011-11-04 12:49:12, 897 DEBUG: dsilib - created queue factory.
  2011-11-04 12:49:12, 909 DEBUG: DocucorpMsgUtil - usher for ' C:\docclnt\doc
  client.XML' is com.docucorp.messaging.data.marshaller.SOAPMIMEDSIMessageMarshall
  amplifier
  2011-11-04 12:49:12, 912 DEBUG: dsilib - created usher.
  2011-11-04 12:49:12, 914 DEBUG: debug - createMessageQueue - (1).
  2011-11-04 12:49:12, 919 DEBUG: dsilib - Created Queue in DSIInitQueue.
  2011-11-04 12:49:12, 920 DEBUG: debug - createMessageQueue - (2)
  2011-11-04 12:49:12, 921 DEBUG: dsilib - Created Queue in DSIInitQueue.
  2011-11-04 12:49:12, 931 DEBUG: debug - [C] - putMessage - messageID = < 2612876F-6
  A51-7553-1E2F-DFB9264 >
  2011-11-04 12:49:12, 940 DEBUG: debug - [C] - putMessage() - SUCCESS - messageID
  = < 2612876F - 6A 51-7553 - 1E2F - DFB9264 >
  2011-11-04 12:49:27, ERROR 955: debug - getMessage(): Socket data not available
  for playback. Timeout = < b > 15 seconds total. Time elapsed = < b > 15 seconds. Found by
  your = < false >.
  2011-11-04 12:49:27, ERROR 971: debug - * properties HTTP Error *.
  2011-11-04 12:49:27, ERROR 984: debug - http.reuse.ports = < 15 >
  2011-11-04 12:49:27, ERROR 988: debug - http.url = < http://localhost:49152 >
  2011-11-04 12:49:27, ERROR 992: debug - marshaller.class = < com.docucorp.messaging
  . data .marshaller .SOAPMIMEDSIMessageMarshaller >
  2011-11-04 12:49:28, ERROR 011: debug - *.
  2011-11-04 12:49:28, 019 INFO: dsilib - received error code 3 of getMessage.
  2011-11-04 12:49:28, 024 DEBUG: dsilib - queue entry closed in DSITermQueue.
  2011-11-04 12:49:28, 032 DEBUG: dsilib - closed in DSITermQueue output queue.
  2011-11-04 12:49:28, 040 DEBUG: dsilib - factory of line closed in TermInstance.
  2011-11-04 12:49:28, 043 DEBUG: dsilib - closed the marshaler in TermInstance.
  2011-11-04 12:49:28, 052 DEBUG: dsilib - about to release customer environment and
  current thread Tach of FMV in TermInstance.
  DSIGetQueueRec failed
  
  What can I do to get it working?
  
  Concerning
  
  Florian

  Hi Florian.

  If you are installing Windows 7, you should be aware that the default HTTP port 49152 is now a dynamic port for Windows 7 (see http://support.microsoft.com/kb/929851).

  To get your installation to work, you should only change your files docserv.xml and docclient.xml to change your ports:

  
  com.docucorp.messaging.data.marshaller.SOAPMIMEDSIMessageMarshaller
  com.docucorp.messaging.http.DSIHTTPMessageQueueFactory
  http://localhost:49152*.
  15
  30
  

  Simply specify a port not used as 48152 and you should be all set. You can use "netstat - a" from a command prompt to view the ports in use on your computer to make sure that the port you have chosen is not already in use.

  -Andy

• Help! Installation of the router problem!

  Hi all! This got me so confused and stressed! I have internet with my Dell desktop computer connected directly to the modem. Works perfectly! We bought 3 different routers and they ALL did EXACTLY the same thing! The second I plug the router with the other end of the ethernet cable, the computer thinks that there is no network connection? The light isn't yet on where the ethernet cable is plugged in to the back of the computer? But the light burns if its plugged on the modem? Which leads me to believe that there is nothing wrong with the cord... The lights work on the router, which makes me think this isn't the router... All bulbs work on the modem that once more, makes me believe that there is nothing wrong with that either? I have everything reset, unplugged everything and he tried once again too many times now! Help, please!