Installed Windows 7 on my netbook but keep getting the blue screen while surfing Web sites
Hello!
First of all, this is my first post time on these forums, I often read them and think they are great!
Now on to my question, I recently installed Windows 7 on my LG x 110 netbook. I ran the windows Upgrade Advisor 7 and confirmed that my netbook managed to all the minimum requirements for a 32-bit install. After installing Windows 7 my pc works perfectly (better than XP in fact) has installed all of the drivers needed to run automatically unless the driver for my microphone and my 3gs integrated internet which I managed to resolve. The only problem I have is sometimes while surfing the web, I get the blue screen of death and my netbook restarts. I was not able to understand by myself am so regarding this forum hoping to repair... I contacted LG for information on downloading upgraded drivers, but got a response from them saying that my pc is not supported with drivers for windows 7. Here is some information from the Center problem with Windows 7, I don't know if it's necessary info, please tell me where to find the correct information and how to access it.
Problemsignatur
Information additional om problemet
BCCode: c2
BCP1: 00000007
BCP2: 00001097
BCP3: 8078AE94
BCP4: 8078AE74
OS version: 6_1_7600
Service Pack: 0_0
Product: 256_1
Bucket ID: 0xc2_7_RTL8187Se! PlatformFreeMemory + 1 b
ServerInformation: 47840a85-d17f-4bd7-8fa5-f385071573a0
Any help is greatly appreciated as I really want to re - install Windows XP because Windows 7 runs so well, even on a low technical specifications.
Handelsenamn: BlueScreen
OS version: 6.1.7600.2.0.0.256.48
Sprakvariant-ID: 1053
It seems that you have a C2 Bad Pool Caller error, which is difficult to analyze without the minidump file. If you googled around and find WinDBG, you can open the minidump file.
Look for the line: nom_image: it will tell you exactly what file has caused the error. If all goes well, once you find exactly what caused the error, you can search for updated drivers/software. At first glance, I would say it was the Realtek drivers because you see the line RTL8187Se in your info.
My MSI Wind U100 netbook works also Win7 perfectly. Double boots with MacOSX too, just because I wanted to see if I could do it. I change the hard drive (for a bigger) and added the RAM. Nothing low spec thereon compared to what was needed for WinXP when it came out!
Try this driver, it should do the trick. http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PFID=40&level=5&Conn=4&ProdID=172&DownTypeID=3&GETDOWN=false&downloads=true
And since this is the NETWORK/connection wireless card driver, he explains why the errors come during surfing!
Tags: Windows
Similar Questions
-
try to install windows vista 32 bit and I still get the blue screen
I try to install vista I have an asrock n68 - gs3 ucc/n68-s3 ucc motherbroad amd athlon x 2 250 dual core 3.0 ghz processor and 4 GB dd3 ram and a 1 TB hard drive and a super 8400gs 512 MB/dual-link dvi/hdmi graphic card I get a blue screen saying 0x0000001a can some please help me with this problem thank you
Hello
It sounds like a RAM issue.
See if this helps you;
See you soon.
-
install windws xp profesional sp3 on my loptop and installing installation opens blue skreen and dll error (C = 0000135) gdi32not faund I can't solve this problem
original title: I install windws xp profesional sp3 on my loptop and installing installation opens blue skreen and dll error (C = 0000135) gdi32not faund I can't solve this problemHi Vytautassvitojus,
· The computer have any OS installed?
· Are you able to boot to the desktop?
If you are not able to boot to the desktop and then remove the external devices except the keyboard and mouse, perform a chkdsk from the recovery console and then try to install Windows.
To run chkdsk from the Windows Recovery console. You can check the links for a description of the Windows XP Recovery Console
http://support.Microsoft.com/kb/314058
Important: If all available hard disk data can be lost when running chkdsk, as the chkdsk attempts to repair the affected area.
I hope this helps.
-
Windows Vista will not start up - keep getting the black screen
I read through the questions answered similar questions and still can not past the black screen with windows vista. It's on a dell inspiron 1525. Also, it does not start in safe mode and I tried booting from the last good configuration and is still stuck on the black screen. This just started a few days ago, and the computer was working fine until this date. Can you help me?
Hi Jimazona,1. from when are you facing this problem?2. any change in software or new hardware on your computer?Method 1:First of all I suggest you to disconnect all devices external one except keyboard and mouse and try to start your computer and check.Method 2:I also suggest you perform a startup repair and check if this solves the problem.Follow the steps below:
a. Please insert the Windows Vista DVD and restart the computer.
b. when we are asked to press a key to boot from the DVD, please press enter or the SPACEBAR.
c. Select your language settings, and then click Next.
d. click on repair your computer.
e. Select the operating system you want to repair, and then click Next.
f. in the System Recovery Options menu, click Startup Repair. Startup Repair can invite you to make choices as it tries to solve the problem, and if necessary, it may restart your computer, because it makes the repairs.
Access the link below for more information on the Startup Repair:Startup Repair: frequently asked questions
http://Windows.Microsoft.com/en-us/Windows-Vista/startup-repair-frequently-asked-questions
See also:
http://social.answers.Microsoft.com/forums/en-us/vistawu/thread/24b44a01-872e-4d87-867f-ed01a3579031/I would like hearing that the results back on your part about what happened after trying each method.Thank you, and in what concerns:
I. Suuresh Kumar - Microsoft technical support.Visit our Microsoft answers feedback Forum and let us know what you think.
-
reformat and reinstall Windows XP but get the blue screen on the windows configuration page
I'm trying to reformat and reinstall Windows XP on my Dell XPS400, but I get a blue screen on the Windows installation page that says... A problem has been detected and Windows has shut down to prevent damage to your computer. How can I make this? I want to give this computer to my grandchildren.
Hello
1. why you try to reinstall Windows XP?
I suggest you to try the steps below and check if they help to resolve the issue.
Configure your computer to start from the CD-ROM drive. For more information on how to do this, refer to your computer documentation or contact the manufacturer of your computer. Insert your Windows XP installation CD, and then restart your computer.
a. when the message Press any key to boot from the CD appears on your screen, press a key to start your computer from the Windows XP CD.
b. press ENTER when you see the message to install Windows XP nowand then press ENTER is displayed on the Welcome to Setup screen.
c. do not choose the option to press R to use the Recovery Console.
d. in the Windows XP licensing agreement, press F8 to accept the license agreement.
e. make sure that your current installation of Windows XP is selected in the box, and then press R to repair Windows XP.
f. follow the instructions on the screen to complete the installation.
See the following link for more details on the repair facility:
How to perform a repair of Windows XP installation, if a later version of Internet Explorer is installed
Hope this information is useful.
-
I have updated Flash player twice but keep getting the box icon telling me to update?
I have updated Flash player twice but keep getting the box icon telling me to update?
@zeyoo,
Please let us know your operating system and your browser.
Please see the following documentation which has instructions on installation of Flash Player:
Windows: http://helpx.adobe.com/flash-player/kb/installation-problems-flash-player-windows.html
Mac: http://helpx.adobe.com/flash-player/kb/installation-problems-flash-player-mac.html
Thank you
Sunil
-
Installed the network updated drivers hp support page now I get the blue screen of death
Installed the network updated drivers for my laptop hp support page and now I get the blue screen of death a few minutes of Internet usage.
I can reboot the computer, but it only works for a little bit before again becoming the blue screen.
I tried to download and reinstall the hp 8 drivers network twice now. (Product number: QJ793AV-#ABA)
I am running windows 7 (x 64) and downloaded all the updates as well.
Any help would be greatly appreciated.
I made an another windows update and seems to be ok for now
-
Windows Vista crashes, I get the 'Blue screen of Death' and I have to restart. Different errors each time it crashes. I tried to reinstall vista without success of the problem being fixed
Hello
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.html-------------------------------------------------------------------------
Also this, so you can see the probable bluescreens.Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
http://www.winvistatips.com/disable-automatic-restart-T84.html-------------------------------------------------------------------------
Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during "blue screen of death," collisions
http://www.NirSoft.NET/utils/blue_screen_view.html
Displays information on all the "crash" of a table - freeBlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.
You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
system installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-------------------------------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).
Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
smile, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob - bicycle - Mark Twain said it is good. -
After that the installation of upgrades KB2419640, KB976902, KB890803 I'm unable to boot. I get the blue screen. I used chkdsk, memtest etc. No problem. I disabled the upgrades to prevent settling. I'm not comfortabel thereby. Is there a solution?
You are able to boot mode safe? If you can, do and run System Restore:
To access the system recovery environment in Windows 7, simply start your PC, just before the system loads the Windows operating system. Press the [F8] key function 8 on your keyboard which will launch the menu Advanced Boot Options. You will see a new option 'Safe Mode', select this option and press 'Enter' on your keyboard.
System Restore -Windows 7 features - Microsoft Windows
After you're booted in Normal mode, click Start, all programs > Windows Update
Check for updates, now updates you're experience problems with, each of them right click and click "hide update".
If they are updated driver in particular, do not install them, hide them instead, any update of the driver offered, instead of this download directly from the manufacturers Web site.
HowManage , Configure and troubleshoot Windows updates releasing it's easy: with Windows | ActiveWin | Laptops | Microsoft MVP
-
Is there anywhere to get a new copy of the system recovery disc for my windows vista computer. I have a HP Pavillion and I get not anywhere when trying to start repair, it tries to fix my computer and takes forever... and then I get the blue screen saying I need to reload windows. The recovery discs that I burned when I bought the computer do not work. What are my options?
How to reinstall Vista
Contact the manufacturer of the laptop computer and ask them to send you to vista recovery disks to reinstall the operating system back as it was when you bought it
they do it for a nominal cost of $
also ask them if you have a recovery partition on your hard drive to get back to the way you bought
you would normally press F8, F9, F10 or F11 or Alt + F10 or 0 to start to start the recovery process according to the manufacturer
Ask them of the exact key sequence
With HP normally press you F11 at startup to start the process of recovery from the recovery partition
or borrow a vista microsoft dvd; not a HP, Acer recovery disk etc
Make sure that you borrow the correct 32-bit or 64-bit microsoft dvd to your computer
they contain all versions of vista
This is the product key that determines which version of vista is installed
http://www.theeldergeek.com/Vista/vista_clean_installation.html
How to replace Microsoft software or hardware, order service packs and replace product manuals
http://support.Microsoft.com/kb/326246
If the problem persists with the recovery process, contact HP
http://welcome.HP.com/country/us/en/contact_us.html
or try HP support froums
-
I get the blue screen with the exception of system Service in Windows 8. It seems that many people have of it. I can't use my computer without losing all the data every few minutes. It is brand new. Fix? It often happens with Firefox, but other times too and restarts sometimes when you type an e-mail in the e-mail of Windows 8 program.
For this recent System_Service_Exception error, if you have an AMD graphics card try the next tool from AMD to try to get the latest graphics driver:
http://support.AMD.com/us/gpudownload/Windows/pages/auto_detect.aspx
According to me, a recent update of Windows, maybe the 2778344 which updates win32k.sys to the 6.2.9200.16503 version, could cause a conflict with the AMD graphics driver.
Many users report the same error recently and so far have all AMD/ATI graphics cards.
If all goes well the graphic driver update will help.
If the problem persists, consider uninstalling 2778344.
Then, at the moment, 'hide' 2778344.
-
I installed Lr 6.01, but keep getting the trail days remaining
There is a similar question here, but it's for CC.
I installed DVD for a perpetual license and have the serial number. Also, when I go to 'manage my account' it shows that I bought Lr and provides S/N. However, when I run Lr, I keep getting the message on the remaining days. I was expecting it to disappear after the uninstallation of the test and installation and the upgrade to the paid version (not CC). The message says I have 6 days remaining until the end of the trial. I don't want to lose my job in 6 days. How can I ensure that my paid version will continue after 6 days?
Please, try the steps mentioned below to serialize LR 6:
- https://helpx.Adobe.com/Lightroom/KB/serialize-Lightroom-CC-trial-to-activate-as-Lightroom - 6.html
- https://helpx.Adobe.com/x-productkb/policy-pricing/activation-network-issues.html
I hope that these links would help.
Atul_Saini
-
I find the minidump files and tried opening them and could not. Files and downloaded programs of debugging appear in the program. When I try to open them I get "you must be an administrator to open" insofar as I know that I am the administrator because supposedly everything I need is another administrator account. Also my restore will pass in a few days, and the box is no longer available. Also had an error on my printer files so I removed them, but as I (after) that I pressed the firm PC, the blue screen appeared and had to turn it off manually and of course got the minidump error message when I started again. If at this point, I'm still waiting to see if deleting the files printer helped. Any information would be appreciated.
OK, I'll look for your next post with minidump files.
-
So I try to reinstall a printer on a computer and I get the message that the printer cannot be installed and the environment specified is not valid. It was working a week ago and now it is not. The printer has already been uninstalled, so I'm stumped. Any help would be appreciated.
Printer is HP Laserjet 1020
Hi miket219
I suggest refer you to the below provided the link and download the latest drivers available for Windows XP on the Web site. Check that if the installation of the last driver put up-to-date helps you solve the problem-I hope this helps.
-
- I have the Windows version I want to install on my lalptop on another computer, also, is there a way to get the product key from here.
Contact Microsoft Support for a replacement product key.
Maybe you are looking for
-
When I delete mail in my Inbox, it doesn't go into the deleted folder?
MacBook Pro, Mac OS X (10.7.1) el Capitan version 10.11.15 When I delete mail in my Inbox, it does not seem to go in the folder deleted... or should I say it seems to go the deleted folder, but when I click on the Inbox and in a different Inbox addre
-
I want to change the format of the date in the top bar of the screen. The current format is: Wed 11:53 I want to change it to: Saturday, December 5, 2015 11:53 In other words, I want to register the date, including the year. Any suggestions?
-
Edit Tree Control Question, specific cells
Hello I have a question on the modification of tree controls. I have played around with the properties and to date have not thought to it. That's what I'm doing: I have a tree with multi-column control. The columns are essentially: name, Description,
-
Use the angular position of the encoder to trigger Digital out
Hello I am a novice user of labview, I have access to three modules, two NI9201 and a NI9401. I have an angular encoder is used to measure the angular position of a crankshaft of engine, what I try to do is to use the encoder to trigger a digital cam
-
An e-mail address that I basically started using as far as when I got on the internet now serves as part of a private domain". Can you please explain. THX