Intel RAID Option ROM

Similar Questions

• HP BL460c G8 option ROM E5 - 2620 Messages

  Hello

  I have a HP BL460c G8 server, I want to access messages Option ROM, which is normally when the prompt "Press any key to see the option ROM message" appears during the reset of the blade, as shown below.

  However, this screen is not displayed. Please notify.

  Thank you for your help.

  

  Hello:

  You can also ask your question on the HP Enterprise Business Community - section blades support forum:

  http://h30499.www3.HP.com/T5/HP-BladeSystem-Server-blades/BD-p/bladescategory01#.VZFVqk3bK9I

• OPTION ROM - configure SSD as a CACHE

  ZBOOK 15 HP

  F0U63ET #ABZ

  S/O: WINDOWS 7

  My laptop has 750 GB HARD disk and 32 GB SSD which should work as a cache. I needed to re - install windows N/A 8-7, but I do not know how to set up the SSD as a cache.

  S/O installed the 750 GB HARD disk in RAID mode.

  When I try to install HP DVD Intel Rapid Storage Technology software anything happen. After reboot, software and drivers not installed. NO ERROR MESSAGE.

  Screenshot shows you the current situation. I am not able to create a Volume as a cache in the ROM OPTION.

  Hope someone here can help me.

  Thank you!!

  

  Hi Davide82,

  To get your question more exposure I suggest you post in the trade forums since it is a commercial product. You can do it at Business Forum.

  Thank you.

• Want 4-1130US access Intel RAID Manager from the BIOS or screen of the Advanced BIOS setting?

  I just got the ultrabook of 4-1130us envy.  I need to access the screen of the Manager RAID Intel and advanced the BIOS configuration screen.

  By pressing "Esc" at startup until gives me only ordinary BIOS screen, and many options are all grey that I can't change.  How to access these screens?

  Thank you

  Thank you

• ESXi 3.5 installation & pricing on Intel S5000XVNSASR Options

  I'm using VMWare Workstation 6.0 for a year on a Lenovo Thinkpad T60p portable computer. Now, I would like to move the virtual machines on portable computer to a server. I have an Intel Server to measure with the following configuration:

  • 2 x Quad Core Xeon L5320 1.86 MHz 8 MB L2 Cache processor

  • Card mother S5000XVNSASR

  • memory Kingston 667 MHz DDR2 ECC fully buffered main 4 x 4 GB

  • ATI FireGL V7300 512 MB PCI graphics card

  • 2 x Seagate Cheetah ST3300655SS 15 K RPM 300 GB hard drives in Hot - Swap Cage (AXX6DRV3GEXP) Intel

  • SC5299WS 10-Bay full EATx Chasis

  • PCI-E SRCSASJV RAID controller

  I have evaluated both the available virtualization hypervisors and concluded that VMWare ESXi 3.x is the best choice available. Track the version of VMWare ESXi 3.5 U3 works well on the configuration of the server above.

  How much it would cost to buy a basic version of this software? Just the ESXi and VI3 Client Server with no support.

  I can't understand the pricing options. ESXi said website is free but after installation, sales VI3 on the Windows machine shows a trail down for 60 days. Is - this trail countdown to ESXi server or VI3 customer?

  Any help will be much appreciated.

  Free ESXi will operate up to 32 cores if you.   In a very small number of cases ESXi has not been able to see all the hearts and which is usually resolved with a BIOS upgrade.  But is most cases, free ESXi with use all cores on the processor you are using.

• Updated intel RAID drivers without losing the RAID 0

  Can I install the latest drivers from "ICH8R/etc/PCH SATA RAID controller" Inter without losing my current RAID.  I know that there is "UPDATE" in drivers... just did during the shutdown/restart installation?

  Hi KenMcC,

  Yes, you can install this update. Hardware updates are not installed automatically. Need to manually install these updates. Updates are correctly configured only when you restart the system after their application.

  Before applying this update, we recommend that you contact the support team of Intel to know the features of this update.
  Visit: http://www.intel.com/p/en_US/support?iid=hdr+support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• HP EliteDesk 800 G1 TWR: EliteDesk 800 G1 TWR - no Intel-vt option in bios

  I'm trying to VM Player allows you to create a virtual machine of several of our machines for deployment purposes.  Although we have 3 different models of PC, they use all PheonixBios.  To create the virtual machine, I need to enable Intel-vt in the bios but I don't see any option to do so.  I looked at the processor i7-4770 and it should support Intel-vt.

  Any suggestions?

  unngg nevermind, I misunderstood something

• HP 350 G1: Intel RAID driver but...

  System: HP 350 G1, BIOS F.12, Win7 Pro x 64, drive HARD 750 GB mSata mS200 Kingston SSD 120 GB, 8 GB of RAM

  OS on SSD (boot pertition), bur also HDD data partition system.

  Mobile Intel Express Chipset SATA RAID Controller v. 13.6.0.1002

  

  

  Tools for the performance of SSD fresh optimazing and Abelssoft SSD and report SSD Tweak:

  

  

  I'm confused, I'm running in IDE mode?

  The NCQ and the TOPPINGS are on doesn't mean that I'm running in AHCI mode?

  How will I know?

  

  What do I need to change in the BIOS (what?), or what I need to make changes in Windows (registry)?

  Thank you

  Hello:

  There is no way you can activate the AHCI in the BIOS for this drive.

  The only thing you need to do is to install the latest driver/software Intel RST that supports completely SSD on the RAID drives mode including trim from the link below.  Third file listed.

  You can ignore these reports because there is nothing you can do about it and no need to.

  https://Downloadcenter.Intel.com/download/24779/Intel-rapid-storage-technology-Intel-RST-RAID-driver

  I hope someday, device manufacturers will be re - write these programs to not report problems on any PC with a 7 series Intel chipset or newer, when the disc is in RAID mode.

  The hard drive is set to AHCI by default.

  I wanted to put a regular SSD instead of hard drive in my G1 of 350 HP, but I can't figure out how to get out the disc.  It does not move.

  Manuals says to release the cable and lift up the drive.  With what?  I tried with both hands and it is stuck fast.

  I didn't want to damage, so I put this project on hold for now until someone post a YouTube video on how to remove the drive.

• Intel Raid Controller

  Hello everyone;

  I have a Hpm7490n that I've upgraded to Windows 7 and it works fine. However back when it was XP I had an Intel program that followed the RAID of the factor. He showed me the health of disks on my computer. When I upgraded to Windows 7, I lost this program and I would like to get it back. Can someone help me with this?

  Thank you.

  Hello:

  I think that you need the Intel Matrix Storage Manager software.

  You want the file 3rd on the list.

  https://Downloadcenter.Intel.com/Detail_Desc.aspx?DwnldID=17882

• Desktop computer HP P6813w there a RAID option for drives in the BIOS?

  Hello

  Looking to buy one of these HP p6813w.

  I was wondering if the BIOS supports RAID 2 discs.

  One-piece

  Hi one-piece,.

  Boot in the bios (F10 setup) and get off at the fall of peak.  Look at the setting for the sata controller mode and see if you have an option to select RAID.  I do not think that the motherboard in the P6813w RAID capacity according to the information I've seen made available by HP.

  If you really want to RAID, then you could buy a RAID PCI card - E to support two data disks.

• How to have SATA drives connected to an Intel RAID controller as removable drives

  HI: we have a Supermicro Server with controller series Intel C600 and we would like to use some of their drives and ports as removable devices, to allow to copy media from one server to another. I mean:

  -The controller has 4 ports with 4 disk on each, in total 16 records

  -The first 4 ports will remain the same, not removable (BONES in Raid 1, media in Raid 0)

  -Other ports (2-4) will be used with SATA SSDS, and we need to delete them via Eject hardware (such as a hard drive attached) and then be able to attach them on the backup server to read the media.

  As far as I know, there is a DWORD I maybe need to add in the registry, but some help would be more than welcome to solve this problem.

  It is the opposite, to not allow the HARD drive to be ejected.

  [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\asahci64\Controller0\Channel0]
  "TreatAsInternalPort"=dword:00000001
  
  [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\asahci64\Controller0\Channel1]
  "TreatAsInternalPort"=dword:00000001
  

  Thanks in advance!

  Hello Felipe.

  Thanks for posting your question on the Microsoft community.

  The question will be better suited to the audience of professionals on the TechNet forums.

  I would recommend posting your query in the TechNet forums.

  TechNet Forum
  https://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w7itpro

  Note: Serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://Windows.Microsoft.com/en-us/Windows/back-up-registry#1TC=Windows-7

  Thank you

• ESXI 5.1 takes supported intel RAID?

  Hello, when I try to install esxi 5.1 on my server (it's a motherboard supermicro very X9SCL/X9SCM), I have configured a RAID1 (2 discs) and a RAID5 (4 discs).

  I see all 6 discs, but they are not in RAID mode.

  Any ideas?

  Thank you!

  Jason

  This is because ESXi does not support software RAID. The best bet would be to find a RAID card with a cache with battery backup that is listed in the HCLof VMware.

• Conversion of Raid 1 configuration to 1 normal hard drive with Windows XP Professional

  I have a Dell Precision Workstation 380, which has been set up at the factory in Raid 1 with 2 Seagate 160 GB hard drives.  The operating system is Windows XP Professional.  I would like to delete the Raid 1 configuration and that the computer is a normal hard drive configuration 1.  Can someone help me with a step by step procedure to achieve this?

  Hi cbcenterplus,

  RAID 1 means that you essentially two drives separated with identical information. In order to break the RAID is simple. Start on the Intel RAID Option Rom utility (ctrl + I), replace two disks drives non-members, and then restart your computer.  The 2nd disc will receive a new drive letter, and you can get in shape by using the disk management and have extra space.

• Optical Drive turns W530 offshore running Windows 8

  With Win8 on W530, the optical drive turns off shortly after start. Failed device management after that. Accessory optical drive and a UJ-260 do the same thing.

  BIOS 2.52 and 2.53: same problem. Main card has Intel RAID option ROM.

  Running Windows 7, the optical drive stays on without any problem.

  I would like to hear if there is a difficulty before you restore Windows 8. Win7 good for now.

  Try this: http://techdows.com/2011/09/windows-8-turns-off-power-to-optical-drive-when-there-is-no-media.html

• Z210: Bad support/problem with recovery of an Z210 system when changing the RAID configuration backup

  My Z210 accompanies stripped Bay RAID-0, which currently consists of 2 x 1 TB HDD where the OS partition. I want to change that in RAID-1 mirror, but as the application of TSRI does no such RAID level migration, I thought I would try another approach.

  As a solution, I'd do a backup using the Windows backup and restore application. Then, I would change the table using the Boot ROM TSRI before restoring the backup to this new array. But obviously backup 1.9 TB in a table of 932GB will not

  So, to make a backup, I firstly disabled 'System Protection' and the file 'Page '. This allowed me to reduce the OS partition to about 50 GB using disk management. Then I re - activate 'System Protection' and the 'Page file' before making the backup and the creation of a system recovery disk. This resulted in a backup of 35 GB that I stocked up on a USB external drive. And now a backup of 35 GB can fit on my reconfigured 932GB RAID - 1 mirror

  As such, I cold booted my system and during the boot process, I pressed CTRL-I to get the State of mind RAID Intel Boot ROM. you, CTRL-I've worked only if I started cold and the HP USB keyboard directly connected the first USB slot at the back of the system. The first USB slot is at the top left when you look at the back with the portrait of the tower. Connect the HP USB keyboard in USB port or in the hub of my Dell monitor does not allow me to access the ROM to Boot Intel RAID!

  HP should really study this fault

  In any case, when I could access the Intel RAID Boot ROM, I deleted the RAID-0 stripped existing and created a new RAID-1 mirror. Obviously, the process is destructive and wipe the BONES of the table but that's what my backup was to

  Then I started on the Windows system recovery disk, plugged the USB external drive and proceeded to recover my system.

  Everything worked as expected with the operating system partition uses about 50 GB. A simple trip to disk management enabled me to extend the volume to occupy the space allocated, as presented by the RAID-1 array. As such, I find myself with about 932 GB partition that appear in the windows disk management tool. After a check disk and reboot (which fixed some minor issues) all seemed well.

  But no, everything was fine

  Well that ROM boot RAID Intel sees that a mirror RAID-1 about 932 GB and the operating system sees a partition about 932 GB, both as expected, demand for Intel RST in windows States the following:

  

  I don't seem to have indication of what type of table, it is, an options to change the name of the table or an option to check the integrity of the array through the TSRI application in windows. If something is screwed

  But after the update for the application of iRST version 10.6.0.1002 Intel (the newest HP of) version 11.2.0.1006 (version Intel got very practice), the question seems to correct itself. Now the RAID, Windows boot ROM and the request of TSRI in Windows all agree that the table is indeed a mirror RAID-1 932 GB.

  

  I don't know what caused the problem, if it's related to something that was wrong with the process that I used, if she is simply resolved by reinstalling driver, or if this is a fix for a known issue that Intel has included in their questions later from the pilot.

  But what I know is that Intel has resolved a number of issues in the version 12.9.0.1001 driver (which is the latest version for the Cougar Point chipsets) compared to the old driver version 10.6.0.1002 HP has on its support page for the Z210.

  And HP seems unwavering in his lack of interest in the Intels 12.9.0.1001 test pilot and then make it available on its support page for what is a product still under warranty

  It is a mediocre service if you ask me...

  Some HP forum administrator or HP support person hide these forums should impose it in the HP management station and get it looked at. The Z210 is still under warranty for some customers and HP needs to pick up the latest drivers available to all suppliers, test them and then release them to their customers via the support page for this product. All the rest is little change us all.

  I was able to resolve the application problem Intel RST by updating to the latest v11.2.0.1006 Intel driver but it has highlighted a few points that HP should address, see linked post above.

  PS: Add this post so I can mark the thread as solved.