Internet Explore (Vista edition) could not start

Similar Questions

• Windows Vista: windows could not start error. is suspended from the "Microsoft Corporation" loading bar then black screen BIOS not acpi compliant

  After you have installed the driver for the zune hd, I was asked to restart my computer. After the reboot, start froze on a white screen. I've seen this before and it is usually because of some connected usb components. so I manually powered down the Tower, disconnected the cable from zune and restarted. This time a screen saying that windows could not start, "launch Startup Repair tool" was recommended. Select this habit makes the startup hang to the progress bar from Microsoft corporation, then to a completely white screen. Although strangely, once only a blue error screen appears which says that the BIOS is not acpi compatible. I can't restart with F8 to go into safe mode, "windows error recovery" still appears. "Start windows normally"produces the same results as the tool to restart launch system. " I have a drive to upgrade to windows 7 and a windows XP upgrade disk. the disc of windows 7 hangs at "starting windows" and the XP disc gives a blue screen error: stop: 0x0000007B (0xF78D2524, 0c 0000034, 0 x 00000000, 0 x 00000000)

  I think I have a BIOS problem, but I don't know how I could continue dealing with the repair. I have no success update the bios from usb flash. Any idea is appreciated.
  Update: managed to start with F8, choose to boot in safe mode and loading hangs after "load: \windows\system32\drivers\crcdisk.sys"***.
  the machine is a gateway LX6810-01 (friend motherboard)

  Hello

  1. What is the exact error message when Windows Vista does not start?

  2. you have the disk Installation of Windows Vista operating system?

  I suggest you change the mode of RAMA to IDE in the BIOS. You can contact the PC manufacturer for assistance.

  Note: BIOS change / oxide of additional metal (CMOS) semiconductor parameters incorrectly can causeserious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

   

  In addition, perform a check disk in Windows Recovery Mode.

  (a) Insert the Windows Vista installation disc in the disc drive, and then start the computer.

  (b) press a key when the message "Press any key to boot from CD or DVD".

  (c) select a language, an hour and the currencyand a keyboard or an input method, and then click Next.

  (d) click on check drive for errors.

  (e) in the System Recovery Options dialog box, select the drive of your Windows installation and click Next

  (f) to the System Recovery Options dialog box, click on check Drive for errors.

  (g) use the switch/r to run the disk check.

  Important: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost

   

  It will be useful.

• Internet Explorer and games does not start; no error message.

  Hi, I had a lot of problems with my computer lately, and it's the last that I have not been able to solve.  I'm running the 64 bit version of Windows 7 Home Premium in a computer, I implemented last summer (the motherboard is an ASUS P5N - D for details).  I recently decided to bathe my HDD Seagate on fire right through a "boot and nuke" program, hoping to relieve a massive corruption of Windows file.  I had a few difficulties, reinstallation of Windows through my installation disc - is now on his third relocation, because I found myself in the limbo of the repair to start due to corrupted registry errors the first two times (although Windows went perfectly fine as a first step, the problem is presented when you restart).  On the last installation, I could run long enough to reacquire all my drivers through the internet, and I even managed to install and play a game for a while.

  When I turned off my computer had 53 updates to Windows Installer.  Let them install and when I started it this morning, Windows wouldn't start.  I used the system restore, Windows and then stop again updates give a chance more (I think that they have perhaps been interrupted the first time).  Now, Windows starts correctly, but I can't run my game.  More worrying is that I can't run internet explore.  I tried MS Paint and Windows Media Player and both of these applications are running.  But in the two aforementioned applications, the pointer changes to indicate they're loading a moment and then returns to its normal appearance without loading anything or provide an unique error message.  I opened the Task Manager and watched list applications that I began them - both appear in the handler for a fraction of a second before disappearing without warning.  I have no idea what is the cause and would be very grateful some advice thereon before yielding to frustration and buy a new hard drive.  Thank you.

  Go, I found to open the newspaper is to copy on your desktop (for this, you will need the Admin password) then right click to copy file and 'open with '. Use an editor, I think that the default value in the list is Notepad. Uncheck "always use" that you can't always open these log files in Notepad.

  The problem is that they are not so easy to decipher.

  Have a read of http://support.microsoft.com/kb/929833, this http://support.microsoft.com/kb/928228 (for Vista but should give an idea) and http://www.sevenforums.com/general-discussion/56234-make-cbs-log-useable.html to give an idea.

  The "SFC / verifyonly" does what it says, it does and just detects and reports errors through the newspaper. You can run the command to actually verify and repair errors, but to be honest, I don't know enough about the in's and out of it. I guess it must fix the errors it finds, but I am not sure if there are disadvantages to it. Experts from the SFC SC around?

  I don't think that an information event is usually nothing to worry about, its errors and warnings that can give advice to any potential problems. If you open the error/warning message there is sometimes a link goes to MS who occasionally provides assistance on what to do next. Then click on one of the errors and look for the 'more information' link.

  Have you tried 3, 5, 6 of my first post, & Esp 5. It is possible that your user account is 'pickled :-) ". "rather than the whole system and creating a new test user all might be fine." It is not certain or guaranteed, but shouldn't take long to check.

  It seems that something is damaged somewhere, so maybe try something else is a check disk scan. Open Explorer, right-click your HDs (one at a time), tools, and then click "error checking".

  EDIT - one think more away, you have an AV Checker updated running? Start in safe mode with networking, the errors still occur then (i.e. can you open IE now)? Once in safe mode, see if you can update your AV checker and run a full scan.

• Could not start the Windows Vista firewall

  Hi all

  I can't start the Windows Firewall service in anyway.
  I can't open it via Control Panel, as it is said simply: "the Windows Firewall settings cannot poster because the asscioated service is not running. You want to start the Windows Firewall service? »
  I click "Yes", then he said: 'Windows cannot start the Windows Firewall service. There is no error code indicated.
  I tried running "wf.msc" using the Microsoft Management Console. When this window appears, he says: "there was an error opening the Windows Firewall with advanced snap-in security.; The Windows Firewall with Advanced Security snap could not load. Restart the Windows Firewall service on the computer that you are managing. "Error code: 0x6D9.
  As it seems, I can not start it this way or the other.
  I pressed Ctrl + Alt + Delete and click on the Services tab, then click services on the bottom, and this opens the Services window.
  In the new Services window, I try to start the service "Windows Firewall". I get a message saying: "Windows could not start the Windows Firewall service on the Local computer.; Error 1068: the dependency service or group could start. »
  Therefore, it does not. The service is set to automatic.
  I found another process called 'Base filtering engine', which I discovered is related to the use of the Windows Firewall service. Then, that I try to start this service, and he said: "Windows has no start the engine service of filtering based on Local computer." Error 0 x 80320009: an object with this GUID or LUID already exists. »
  Still, I can't find a way to fix the problem. In addition, the service is set to automatic.
  So if someone could help me, give me ideas or tell me how to solve the problem, it would be greatly appreciated. Thanks in advance.
  P. S. sometimes, when I type things in the command prompt, I get a message saying that "the requested operation requires a rise." What it means
  ?
  EDIT:
  The base filtering engine
  IKE and AuthIPsec Keying Modules

  Internet Connection Sharing (ICS)

  IPsec policy agent

  Routing and remote access

  Windows event collector

  Windows Firewall

  All of these services don't work, with each saying "Windows did not start the * service * service on Local computer.; Error 1068: The dependency service or group could start. ", with the exception of the Base Filtering Engine service.

  EDIT:

  I believe that the motor of filter of Bae is the root cause of the problem, because when I try to start it, it says "Windows cannot start the engine service of filtering based on Local computer. Error 0 x 80320009: an object with this GUID or LUID already exists. ", so that all the other programs on this service, said depedent" Windows did not start the * service * service on Local computer. " ; Error 1068: The dependency service or group could start. ».

  EDIT:

  Hello everyone, I solved the problem. The problem is a corrupted, file called "secdrv.sys. To resolve this problem, I had to first download the file "secdrv.sys' out of my operating system CD. To do this, you must create a partition and "mount" a file on CD, on the newly created partition. The file you have to climb is and is called: "*: \sources\install.wim. Extending .wim means a "file system Windows Image" and to see what files it contains, you will need to download what we call the "Windows Automated Installation Kit". Explicit instructions on the installation procedure and where to get this program, is here: "http://www.vistax64.com/tutorials/86959-access-vista-install-dvd-files.html". Once you have the file mounted, just search the area mounted for "secdrv.sys", then copy and paste it in "C:\Windows\System32\drivers" or that where the drivers from your system. After that, restart and the BFE service and all of its dependencies should work properly. Thanks for the good help like SpiritX.

  Hello everyone, I solved the problem. The problem is a corrupted, file called "secdrv.sys. To resolve this problem, I had to first download the file "secdrv.sys' out of my operating system CD. To do this, you must create a partition and "mount" a file on CD, on the newly created partition. The file you have to climb is and is called: "*: \sources\install.wim. Extending .wim means a "file system Windows Image" and to see what files it contains, you will need to download what we call the "Windows Automated Installation Kit". Explicit instructions on the installation procedure and where to get this program, is here: "http://www.vistax64.com/tutorials/86959-access-vista-install-dvd-files.html". Once you have the file mounted, just search the area mounted for "secdrv.sys", then copy and paste it in "C:\Windows\System32\drivers" or that where the drivers from your system. After that, restart and the BFE service and all of its dependencies should work properly. Thanks for the good help like SpiritX.

• VISTA: backup application could not start due to an internal error: (0 x 80080005) Server execution failed

  The backup application could not start due to an internal error:
  Server execution failed (0 x 80080005)

  Vista Ultimate - trying to COMPLETE the backup of a computer

  Hi people,

  I had a similar problem with Vista (64-bit edition complete edition) machine. I run automatic backups for more than a year. Suddenly, backups started fail with the following error code:

  "The file or directory is corrupted and unreadable 0 x 80070570.

  I thought it would be my external drive - so I tried an another one - same error. After a search of different topics around, I tried various fixes (similar to above), but none of them worked.

  I managed to find the problem though. The issue is not with the drive being written - it's the current backup disc that is the problem. If you want to save your primary drive (C:, for example), try to perform a check of the errors on this drive (right click on your drive home, you are trying to save, choose 'Properties' then go to 'tools' - click 'Check now' under the control of errors - and check both boxes). Since this is the current drive, you must stop and restart - the system then automatically checks the system files and windows files on the next boot.

  After doing this, my problem cleared up. Apparently, the backup software was crashing trying to read a corrupted file or a sector of the hard disk, that he was backing.

• Vista could not start in normal mode and the relocation of scores of hidden factory settings also failed.

  NOTE: THE PROBLEM WAS MY POWER SUPPLY WAS LOW, NEW POWER ADAPT SOLVED MY PROBLEM.   Read more if you are interested in what happened prior to my tent a different power adapter.

  Original title: vista 32 does not start

  After a reboot could enter the mode safe mode with internet connection.  able to restore good boot known beforehand.  But what normal start attempt would not start completely.  tried to reinstall from hidden factory partition.  07:34 minutes, the installation progessed.  then the machine stop.  When you restart get the message "error during installation, restart the computer, and then restart the installation."  When you try to start in safe mode, get error ' cannot install frrom SafeMode ".". "  I have no bootable cd.  to know about a 'platform of recovery' still tells CD also cannot install from this cd.   can I boot from a "devils of recovery" in safe mode and use the hidden partition to reinstall to factory settings as I tried the first time?  or do I need a full installation CD to get the machine to boot?   My question is should I at this stage of start-up during installation seems to have failed?

  as for what caused this problem?  I recently gave a USB external hard drive, but had not written for her.  did a chkdsk of the external hard disk without error.   When the problem was first happening, I removed the battery and the power cord of the acer laptop then pressed the power for 30 seconds to perform all memory the power button.  He got rid of a problem that I had been meet in which received start-up error message not "adapter acer". with battery removed, laptop power problems have disappeared.

  as the system is now, when I try to start everything now alt F10, I get a screen that reads "change windows startup options for: microsoft windows vista ' ' path: \windows\system32\winload.exe" "partition: 2" "HDD;". " d404533e' "[/ noexecute = optin /deteecthal]"

  When I press ESC the next screen "windows boot manager" bed "choose an operating system to stat, or press TAB to select a tool:

  Microsoft windows Vista (single choice)

  "to specify an option fo this choice, press F8."

  "Tools:

  "windows memory diagnostic"

  (diagnosis of memory showed no problem) by pressing TAB toggles between Vista and the diagnosis.

  I tried to boot with external USB hard drive connected and not connected.   the touch pointer was not working, but was erratic.   Sometimes, I could use a USB wireless mouse when it is started in safe mode.   recently the media player would not charge unless I restarted.  (before the system does not at all which is the theme of this original problem).

  When I try to start using f10, I get a screen that seems to ask for entry. the cursor is held after the detecthal of the line as below. What could of entry to enter the boot to continue?

  Winload.exe

  / noexecute = optin /detecthal

  me. surprised... the problem was that my power supply was low.   the adapter provided enough power for the laptop, most of the time.  but sometimes for laptop needs more power that the adapter could supply... so the laptop would be closed.   When I tried a different power adapter in a store, the fully charged laptop and my problem was solved.  lost a lot of time because I didn't know that the power supply was the problem!

• "The dependency service or group could not start" - cannot open network connections to connect to the internet.

  Hello

  Ive recently managed to repair my Vista computer from a black desktop screen, by doing a Virus scan from kaspersky in safemode, thanks for the advice in this thread

  http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/a960276d-5147-4286-A437-711e96e25296/

  However, whenever I try to go to the network connections to connect to the internet, I get the error message saying "the dependency service or group could not start", so I can't update kaspersky for the last secuirity as well as not to use the internet. I tried the system restore, but there is no previous saved location for me to do. :(

  Any help would be greatly appeciated :)

  Thanks in advance

  Sam

  Medion M96350,

  Intel Core 2 Duo,

  T520 @1.5 - Ghz,

  Vista Home Premium

  Hello

  You can use the (SFC.exe) System File Checker tool to determine which file is causing the problem and then replace the file. To do this, follow the link below.

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• PC with Windows Vista does not restart after installing updates, "Windows could not start...". "File:\Windows\system\winload.exe status: Oxcoooooof.

  Last night, I installed Windows updates on my HP Pavilion dv6227cl and now Windows will not boot.  I get the message "cannot start Windows.  A recent hardware or software change might be the cause.  File:\Windows\system\winload.exe status: Oxcoooooof Info: the selected entry could not be loaded because the application is missing or damaged.  I DO NOT have the Windows Setup disc.

  Hello

  I suggest you borrow the CD of windows vista to your friends

  Method 1:

  Step 1:

  I suggest you check in safe mode.

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Step 2:

  If you be able to start your computer in safe mode, I'd say make clean boot and check.

  Place the computer in a clean boot state, then check if it helps. You can start Windows by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After troubleshooting, make sure the computer to start as usual as mentioned in step 7 in the above article.

  Method 2:

  I also suggest you to see link and check.

  Error: Windows could not start. A recent hardware or software change might have caused the problem after installing Windows updates

  http://support.Microsoft.com/kb/2674065

• Windows could not start. A recent hardware or software change might be the cause. (vista)

  I've updated pctools free and there was a mistake by because it came when the computer restarts,

  Windows could not start. A recent Ministry of hardware or software may be the cause. To solve the problem.

  1. Insert the windows installation disc and restart your computer.
  2. choose your language settings, and then click "next".
  3. click on "repair your computer".

  File: \windows\system\drivers\PCTCore.sys

  status: 0xc0000098

  Info: windows could not load a critical system driver is missing or corrupt.

  I tried I went to my computers startup options advanced and tried to run in safe mode, but the same previous screen came. Each option in my boot options is the same screen. I realize that to solve this problem, I might have to reload my OS together.  I tried to put what I believe to be the installation disc in and restart but it starts and says the same message. I don't know how to start from the DVD.

  Someone at - it solutions?

  Change the boot order in the BIOS to boot from the CD drive first.
  How to change the boot sequence in the BIOS
  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

  C:\windows\system32\drivers\pctcore.sys file information
  http://www.file.NET/process/PCTCore.sys.html

• Widows could not start. A recent hardware or software change might be the case. Pre-installed vista so NO CD.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas: widows could not start.  A recent hardware or software change might be the case.  Pre-installed vista so NO CD.  SAFE MODE AND ALL THE OPTIONS (LAST KNOWN CONFIGURATION, SAFE MODE WITH COMMAND PROMPT, ETC.) ALL DO NOT WORK.  Help, please

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  You can't have a cd, but the PC manufacturer if they did not provide recovery disc, there is a hidden restore partition which should be accessed to make recovery disks.

  There the diagnostic utilities provided by the manufacturer of the PC that you can access from the start screen to test your hardware? Access your site from PC manufacturers for help on how to access these if avilable

• Could not start vista windows firewall

  When you try to start the services program through windows firewall I get this error message: windows could not start the service on the local computer's windows firewall.
  Error 1068: the dependency service or group could start.  I need help...

  In addition to that maverick said... Follow the steps below...

  1. run "netsh winsock reset " starting from an elevated command prompt and reboot...

  2. go to the again elevated command prompt, and then run 'netsh firewall set opmode enable' in the command window... that should do the trick...
  Best regards, H.M. KOWSHAL a.k.a W@R10CK

• Windows Vista - could not start 0xc00000f

  I have the Dell Studio laptop.

  Windows could not start. A recent hardware or software change might be the cause. To solve the problem:

  1. Insert your windows installation disc and restart your computer.
  2. choose your language settings, and then click Next.
  3. click on "repair your computer."

  If you do not have the disk, contact your system administrator or computer manufacturer for assistance.

  Status: 0xc000000f

  Info: The boot selection failed because a required device is not accessible

  There is a problem, I don't have any CD for her.

  I am an academic and I want at the end of the work, until school starts again. Please can someone answer my question as soon as POSSIBLE? I'm not a computer genius, but I'd like to have someone who can help. Thank you!

  With respect,
  Lam

  Hello

  I suggest you to contact the system manufacturer for assistance.

• most programs now get error message "could not start from this location after a mail there is session 2 nite".

  After a session 2 nites E-mail there, many programs said message error "could not start program from this location. In addition, long delays after you clicked on a link, a large display hourglass for up to several minutes. Have tried to rebuild, but I think that the problem is still there. Any suggestions?

  What is a "mail session?

  What is, "have tried to rebuild?"

  Edition with Service Pack of Windows XP _ _?

  What anti-virus application that you use, and if she slept in day?

  Search for malware:

  Download, install, execute, update and perform analyses complete system with the two following applications:

  • MalwareBytes (FREE)
  • SuperAntiSpyware (FREE)

  Remove anything they find.  Reboot when necessary.  (You can uninstall one or both when finished.)

  Search online with eSet Online Scanner.

  The less you have to run all the time, most things you want to run will perform:

  Use Autoruns to understand this all starts when your computer's / when you log in.  Look for whatever it is you do not know using Google (or ask here.)  You can hopefully figure out if there are things from when your computer does (or connect) you don't not need and then configure them (through their own built-in mechanisms is the preferred method) so they do not - start using your resources without reason.

  You can download and use Process Explorer to see exactly what is taking your time processor/CPU and memory.  This can help you to identify applications that you might want to consider alternatives for and get rid of all together.

  Do a house cleaning and the dust of this hard drive:

  You can free up disk space (will also help get rid of the things that you do not use) through the following steps:

  Windows XP should take between 4.5 and 9 GB * with * an Office suite, editing Photo software, alternative Internet browser (s), various Internet plugins and a host of other things installed.

  If you are comfortable with the stability of your system, you can delete the uninstall of patches which has installed Windows XP...
  http://www3.TELUS.NET/dandemar/spack.htm
  (Especially of interest here - #4)
  (Variant: http://www.dougknox.com/xp/utils/xp_hotfix_backup.htm )

  You can run disk - integrated into Windows XP - cleanup to erase everything except your last restore point and yet more 'free '... files cleaning

  How to use disk cleanup
  http://support.Microsoft.com/kb/310312

  You can disable hibernation if it is enabled and you do not...

  When you Hibernate your computer, Windows saves the contents of the system memory in the hiberfil.sys file. As a result, the size of the hiberfil.sys file will always be equal to the amount of physical memory in your system. If you don't use the Hibernate feature and want to reclaim the space used by Windows for the hiberfil.sys file, perform the following steps:

  -Start the Control Panel Power Options applet (go to start, settings, Control Panel, and then click Power Options).
  -Select the Hibernate tab, uncheck "Activate the hibernation", and then click OK. Although you might think otherwise, selecting never under "Hibernate" option on the power management tab does not delete the hiberfil.sys file.
  -Windows remove the "Hibernate" option on the power management tab and delete the hiberfil.sys file.

  You can control the amount of space your system restore can use...

  1. Click Start, right click my computer and then click Properties.
  2. click on the System Restore tab.
  3. highlight one of your readers (or C: If you only) and click on the button "settings".
  4 change the percentage of disk space you want to allow... I suggest moving the slider until you have about 1 GB (1024 MB or close to that...)
  5. click on OK. Then click OK again.

  You can control the amount of space used may or may not temporary Internet files...

  Empty the temporary Internet files and reduce the size, that it stores a size between 64 MB and 128 MB...

  -Open a copy of Microsoft Internet Explorer.
  -Select TOOLS - Internet Options.
  -On the general tab in the section 'Temporary Internet files', follow these steps:
  -Click on 'Delete the Cookies' (click OK)
  -Click on "Settings" and change the "amount of disk space to use: ' something between 64 MB and 128 MB. (There may be many more now.)
  -Click OK.
  -Click on 'Delete files', then select "Delete all offline content" (the box), and then click OK. (If you had a LOT, it can take 2 to 10 minutes or more).
  -Once it's done, click OK, close Internet Explorer, open Internet Explorer.

  You can use an application that scans your system for the log files and temporary files and use it to get rid of those who:

  CCleaner (free!)
  http://www.CCleaner.com/
  (just disk cleanup - do not play with the part of the registry for the moment)

  Other ways to free up space...

  SequoiaView
  http://www.win.Tue.nl/SequoiaView/

  JDiskReport
  http://www.jgoodies.com/freeware/JDiskReport/index.html

  Those who can help you discover visually where all space is used.  Then, you can determine what to do.

  After that - you want to check any physical errors and fix everything for efficient access"

  CHKDSK
  How to scan your disks for errors* will take time and a reboot.

  Defragment
  How to defragment your hard drives* will take time

  Cleaning the components of update on your Windows XP computer

  While probably not 100% necessary-, it is probably a good idea at this time to ensure that you continue to get the updates you need.  This will help you ensure that your system update is ready to do it for you.

  Download and run the MSRT tool manually:
  http://www.Microsoft.com/security/malwareremove/default.mspx
  (Ignore the details and download the tool to download and save to your desktop, run it.)

  Reset.

  Download/install the latest program Windows installation (for your operating system):
  (Windows XP 32-bit: WindowsXP-KB942288-v3 - x 86 .exe )
  (Download and save it to your desktop, run it.)

  Reset.

  and...

  Download the latest version of Windows Update (x 86) agent here:
  http://go.Microsoft.com/fwlink/?LinkId=91237
  ... and save it to the root of your C:\ drive. After you register on the root of the C:\ drive, follow these steps:

  Close all Internet Explorer Windows and other applications.

  AutoScan--> RUN and type:
  %SystemDrive%\windowsupdateagent30-x86.exe /WUFORCE
  --> Click OK.

  (If asked, select 'Run'). --> Click on NEXT--> select 'I agree' and click NEXT--> where he completed the installation, click "Finish"...

  Reset.

  Now reset your Windows with this FixIt components update (you * NOT * use the aggressive version):
  How to reset the Windows Update components?

  Reset.

  Now that your system is generally free of malicious software (assuming you have an AntiVirus application), you've cleaned the "additional applications" that could be running and picking up your precious memory and the processor, you have authorized out of valuable and makes disk space as there are no problems with the drive itself and your Windows Update components are updates and should work fine - it is only only one other thing you pouvez wish to make:

  Get and install the hardware device last drivers for your system hardware/system manufacturers support and/or download web site.

  If you want, come back and let us know a bit more information on your system - particularly the brand / model of the system, you have - and maybe someone here can guide you to the place s x of law to this end.  This isn't 100% necessary - but I'd be willing to bet that you would gain some performance and features in making this part.

• No license file: could not start more

  Hello
  Installed Disqualification in WebLogic... then the Advanced installation steps, but got this error message when starting the server managed by a dndirector App. testing of the installation on Windows 7.
  
  INFO: Refreshing com.datanomic.director.startup.WebApplicationContext@1e4acce: display name [root WebApplicationContext]; start date [Thu Apr 18 17:20:24 EDT]
  2013]; root of context hierarchy
  NEWS: April 18, 2013 17:20:24: dn:director version 9.0.6 (895) starting
  April 18, 2013 17:20:24 com.datanomic.director.startup.WebApplicationContext loadBeanDefinitions
  GRAVE: No license file: could not start more
  NEWS: April 18, 2013 17:20:25: initialization of ZipServerServlet.
  < 18 April 2013 23:20:25 hours CEST > < opinion > < Log Management > < BEA-170027 > < server has established the connection with the Service of diagnosis level domain successfully. >
  
  EDIT:
  The app is looking for a file director.lic in the server\dndirector\WEB-INF\config directory, but the file does not exist here or anywhere for that matter.
  
  Thanks in advance.
  
  Notes:
  Development mode (JDK 1.6_29)
  WebLogic - plan.Xml
  Keystore demo provided by Oracle.
  SSL is enabled on the managed server to the disqualification and Admin.
  Deployed on the server managed of the disqualification.
  Created the required folders, tools, config, dndirector (copied the files required for them) (dndirector contains the directories in config and tools).
  Reboot all servers. dndirector began deployment (all started the active health and ok)
  
  Published by: owbdev99 on April 18, 2013 20:09
  
  Published by: owbdev99 on April 18, 2013 20:23
  
  Published by: owbdev99 on April 18, 2013 20:35

  Hello

  The initial deployment, Disqualification is a demi-cuite startup - just enough to put the web screens to complete the installation (point to the configuration directory and the database). At this point, it generates the appropriate license file. I think that this error can probably be ignored. You are able to get on the web pages of configuration to: http://application-tier server: port/deploymentname?

  Note that there is a topical issue with Weblogic SSL and Internet Explorer IE blocks the default certificate that WebLogic generates its key size. To work around this, you must either use a different browser (Firefox/Chrome, for example) or to generate a new certificate using the Weblogic documentation with a key RSA of 1024 MB size or more.

  Mike

• Firewall Windows disable the Internet Explorer loads Up after slow start after the installation of Windows updates

  Hello, (this the mystery of on and Off and back on Windows Firewall with slow loading of programs like Internet Explorer as this all is pass it on firewall, disable the firewall, the firewall, it occurs only during starts, after he fine / but very annoying on reboots whom he accuses of my computer down) / listed below is the cause of it , and when she first started, you have a solution?

  I recently installed the last 16 (High Profile) updates to security, for most security updates and updates from net framework as well as the removal of malware for windows XP tool.

  After installing these updates, now my Windows Firewall turns off during 'Boot Up' on all restarts. If I try to load Internet Explorer, it will also not load up to minutes serveral / while this happens... That's fine, then finally my firewall itself loads Up quickly turns to Internet Explorer and back on during this time around the same time.

  After these updates these things are happening on my computer now, it's as if there is a process running, but nothing run any virus, Trojan or worm etc just these updates caused this problem. I don't know if it updates is corrupt or not, but have tried different things as system file checker /scan etc with no luck.

  (1) computer boots to the top and seems to Load Up Fine ' until the ' or 'Look at this' but isn't, something is running in the background or process "wing unstalled" is obviously "unhooked", etc..

  2) try to load Internet Explorer last minutes and is very slow to load up, even if I 'don't load Internet Explorer' must still a long while that as in the firewall turn off for awhile some several «minutes» (way too long), before "auto turn on automatically return.

  (3) turns firewall Windows itself on "finally" as Internet Explorer finally loads upwards as well the two Internet Explorer is able to load 'definitely' and the firewall is on "finally" as many minutes later as listed above, at the same time.

  This could be the cause? Only, it has begun to 'After' I ran windows update and installed the 'most recently high security updates for windows XP' there were 16 listed mainly security updates and updates of net framework as well as the software removal tool windows malware.

  That's all that is changed on my system, I tried many things, nothing seems to fix this problem with my computer. I know for a fact that these updates are the cause, but am not sure that you caused it? Or how do to solve this problem, any sugguestions would be appreciated.

  Please answer questions following diagnosis by number in your very next answer (no need to quote this post):

  1. what application or antivirus security suite is installed and your current subscription?  What anti-spyware (other than Defender) applications?  What third-party firewall (if applicable)?

  2 a Norton or McAfee application already installed on the computer?

  3. do you have a Norton or McAfee free trial come preinstalled on the computer when you bought it? (No matter if you have never used or activated).

  4. you are using IE6, IE7 or IE8?

  5. have you ALREADY had the opportunity to do a Repair Installation of Windows XP for some reason any?

  PS: PLEASE DO NOT START ANYTHING IN ADDITION TO NEW THREADS ABOUT IT!

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft