IPhone 6 + during the restore itunes error (9)

Similar Questions

• During the restore system to a previous restore point, I got this error 'access denied 0x80070005.

  original title: 'access denied 0x80070005.

  During the restore system to a previous restore point, I got this error "Access denied 0x80070005" Any Solutions?

  During the restore system to a previous restore point, I got this error "Access denied 0x80070005" Any Solutions?

  Possibilities:

  1. you are not the administrator. You don't have to enter the admin password valid when he asked for it.

  2. you probably have the problem with the infection by the virus.

  If you ARE the admin, suggestions:

  a. run a full scan.

  b. If the machine is clean, do your Safe Mode system restore.

  How to go in safe mode?

  Restart > immediately and repeatedly tapping the F8 key until you see a black and white scree > top? Touch down arrow, and then select Safe Mode > Enter > now that you are using safe mode. Make your system restore.

• I get error code 0 x 80070005 that reads "system restore failed during the restoration of the registry since the restore point.

  Original title: Windows 7 system restore always fail.

  I get error code 0 x 80070005 that reads "system restore failed during the restoration of the registry since the restore point.  I don't have Norton AntiVirus.

  If anyone can help solve me this problem I would be very grateful.

  Thank you for your response.  I forgot to mention in my first post, I tried both methods without success.  However, I finally understand how to solve the problem that led me to want to do a restore of the system in the first place. for now, I am therefore able to avoid a system restore.

  Thanks again.

• Inject third-party drivers during the restoration

  During the restoration, is there a way to inject third-party drivers like Nvidia video card drivers?

  Hello

  Take a look at this post with all the information required by you. "' en.community.dell.com/.../19637349 '
  

• Error snapshot VSS «file too small startup...» "during the restore point creating eventlog ID 12289 in Windows 8

  I am unable to do a restore point. There is plenty of space on both partitions.
  Config: A single drive with 2 partitions, one primary and one extended logical partition with Windows 8 on logic in dual boot with Windows 7 on the primary. The restore point creation in Win7 works OK but in Win8 it never worked alhthough all parameters seem to be OK.
  Device configuration:
  DISKPART > select disk 0
  Disk 0 is now the selected disk. NOTE: there is only 1 disc
  DISKPART > list disk
  Disc # status size free Dyn Gpt
  --------  -------------  -------  -------  ---  ---
  * Online drive 0 93 GB 1024 KB
  DISKPART > list volume
  Volume # Ltr Label Fs Type size status Info
  ----------  ---  -----------  -----  ----------  -------  ---------  --------
  Volume 0 DVD - ROM 0 B G no media
  Volume 1 - D drive of W7 NTFS Partition 54 GB healthy system
  Volume 2 C disc W8 NTFS Partition 39 GB Healthy Boot
  DISKPART > list partition
  Partition # type Offset size
  -------------  ----------------  -------  -------
  Partition 1 primary 54 GB 31 KB
  0 39 extended 54 GB GB partition
  Partition 2 logic 39 GB GB 54
  ---> Note: I do not understand partition 0, there are only two partitions!

  Extract from the event log. Error ID 12289 0 x 80042306:
  The volume shadow copy Service error: unexpected error
  DeviceIoControl (\\?\Volume{6fae1bd1-6bbe-11e2-af9b-806e6f6e6963}
  (- 0000011C, 0x0053c008, 007FB8D0, 0, 007FC8D8, 4096, [0]).  HR = 0 x 80820001,
  The startup file is too small to support persistent snapshots
  Operation:
  Treatment EndPrepareSnapshots
  Context:
  Execution context: System Provider
  ---> NOTE: occurs 4 to 5 times

  Cannot create (process = restore point
  'C:\Windows\system32\systempropertiesprotection.exe ';
  Description is W8 FDC shadow;. Error = 0 x 80042306).
  ---> NOTE: 1 times

  VSS commands: WRITERS, WMI and MSsearch system has failed...
  _________________________________________________________________________
  List writers C:\Windows\System32>vssadmin
  vssadmin 1.1 - Volume Shadow Copy Service administrative command-line too
  (C) copyright 2001-2012 Microsoft Corp.

  Author name: 'Task Scheduler Writer'
  The writer ID: {d61d61c8-d73a-4eee-8cdd-f6f9786b7124}
  Writer Instance Id: {1bddd48e-5052-49db-9b07-b96f96727e6b}
  Status: Stable [1]
  Last error: no error

  Writer name: 'recorder VSS metadata store.
  The writer ID: {75dfb225-e2e4-4d39-9ac9-ffaff65ddf06}
  Writer Instance Id: {088e7a7d-09a8-4cc6-a609-ad90e75ddc93}
  Status: Stable [1]
  Last error: no error

  Writer name: 'Performance Counters writer. "
  The writer ID: {0bada1de-01a9-4625-8278-69e735f39dd2}
  Writer Instance Id: {f0086dda-9efc-47c5-8eb6-a944c3d09381}
  Status: Stable [1]
  Last error: no error

  The writer's name: "System Writer".
  The writer ID: {e8132975-6f93-4464-a53e-1050253ae220}
  Writer Instance Id: {b796dce1-206a-472b-bb86-5417041b341c}
  State: [7] failed
  Last error: Timed out

  Author name: 'ASR Writer.
  The writer ID: {be000cbe-11fe-4426-9c58-531aa6355fc4}
  Writer Instance Id: {eaf13613-1a24-44b5-8622-8e691f1fb074}
  Status: Stable [1]
  Last error: no error

  Writer name: 'writer of Service MSSearch.
  The writer ID: {cd3f2362-8bef-46c7-9181-d62844cdc0b2}
  Writer Instance Id: {43272e0e-d81a-4aa5-abe9-f6bbbfa6f3b0}
  State: [7] failed
  Last error: Timed out

  Author name: 'Shadow Copy optimization Writer. "
  The writer ID: {4dc3bdd4-ab48-4d07-adb0-3bee2926fd7f}
  Writer Instance Id: {20038d53-ecd7-4332-b2f5-ad9a5c465220}
  Status: Stable [1]
  Last error: no error

  Name of the author: "COM + REGDB Writer".
  The writer ID: {542da469-d3e1-473c-9f4f-7847f01fc64f}
  Writer Instance Id: {bf7bd8e4-5aa8-412a-a401-528d6100203a}
  Status: Stable [1]
  Last error: no error

  Author name: 'Registry Writer'
  The writer ID: {afbab4a2-367d-4d15-a586-71dbb18f8485}
  Writer Instance Id: {77018269-1865-4b89-b810-e4a9b6a3b5ab}
  Status: Stable [1]
  Last error: no error

  Author name: 'BIT Writer'
  The writer ID: {4969d978-be47-48b0-b100-f328f07ac1e0}
  Writer Instance Id: {6a7abc2b-e868-45cb-be06-f63e19fb1510}
  Status: Stable [1]
  Last error: no error

  Author name: 'WMI Writer'
  The writer ID: {a6ad56c2-b509-4e6c-bb19-49d8f43532f0}
  Writer Instance Id: {848fabfd-fc83-4c67-ba79-92b274dab8eb}
  State: [7] failed
  Last error: Timed out
  _________________________________________________________________
  Mountvol

  C:\Windows\System32>mountvol
  Creates, deletes, or lists a volume mount point.

  The possible values for VolumeName along with current mount points are:

  \\?\Volume{6fae1bd0-6bbe-11E2-AF9B-806e6f6e6963}\
  D:\

  \\?\Volume{6fae1bd1-6bbe-11E2-AF9B-806e6f6e6963}\
  C:\

  \\?\Volume{6fae1bd6-6bbe-11E2-AF9B-806e6f6e6963}\
  G:\
  ----------------------------------------------
  Lists of C:\Windows\System32>vssadmin providers
  vssadmin 1.1 - Volume Shadow Copy Service administrative command-line tool
  (C) copyright 2001-2012 Microsoft Corp.
  The provider name: 'Microsoft Software Shadow Copy provider 1.0 '
  Provider type: System
  Provider ID: {b5946137-7b9f-4925-af80-51abd60b20d5}
  Version: 1.0.0.7
  _____________________________________________________________________

  C:\Windows\System32>vssadmin list shadowstorage
  vssadmin 1.1 - Volume Shadow Copy Service administrative command-line tool
  (C) copyright 2001-2012 Microsoft Corp.

  Shadow copy storage association
  Volume: (D :) \\?\Volume {6fae1bd0-6bbe-11e2-af9b-806e6f6e6963} \)
  Shadow copy storage volume: (D :) \\?\Volume {6fae1bd0-6bbe-11e2-af9b-806e6f6e6963} \)
  Memory copy ghost used space: 0 bytes (0%)
  Storage space copy allocated Shadow: 0 bytes (0%)
  Maximum space memory copy Ghost: 3.78 GB (7%)

  Shadow copy storage association
  Volume: (c) \\?\Volume {6fae1bd1-6bbe-11e2-af9b-806e6f6e6963}.
  Shadow copy storage volume: (c) \\?\Volume {6fae1bd1-6bbe-11e2-af9b-806e6f6e6963}.
  Memory copy ghost used space: 0 bytes (0%)
  Storage space copy allocated Shadow: 0 bytes (0%)
  Maximum space memory copy Ghost: 3.13 GB (8%)
  ---------------------------------------------------------------------

  Material:
  _________
  Computer brand name: Hewlett - Packard HP Pavilion dv6000 (RG892EA #UUG)
  Operating system: Microsoft Windows 8 Professional build 9200
  Processor: AMD Turion64 X 2 TL - 50 (1600,0 MHz)
  Motherboard: Quanta 30B 8 (nVidia GeForce Go 6100 (C51MV) + MCP51)
  Memory: 2 GB (dual channel)
  Hard drive: FUJITSU MHV2100BH (95 396 MB (100 GB))
  Optical drive: HL-DT-ST DVDRAM GSA - 4084N (DVD + R DL)
  Graphics card: nVidia GeForce Go 7200 [HP]

  Hard drive
  --------------------------------------
  Drive model: FUJITSU MHV2100BH
  Variable speed drive: SATA 1.5 Gb/s
  Drive serial number: NW12T662BYPM
  Firmware revision: 892C
  Disk capacity: 95 396 MB (100 GB)

  Hi Francis,.

  Thanks for posting the query on the Microsoft Community Forum.

  From the description, it seems that the error revceive you associated with VSS snapshot.

  1. What security software is installed on the computer?
  2. Do you have any third-party backup program installed on the computer?

  To begin troubleshooting, I would suggest that you do Check Disk

  • Press Windows key + R
  • Type "cmd" to open the command prompt.
  • Type Chkdsk/r , and press enter.

  Note:

  If all available hard disk data can be lost when running chkdsk, as the chkdsk attempts to repair the affected area.

  Reply with more information about the issue so that we can help you further.

  I had the same problem with a HP dv5000 has an Intel Dual Core processor, after installed the 10 Pro Update window cleaning, after the update sent by Windows Update Service left me with this problem.

  Thank you post I did check in the menu properties C: Tools.

  After that, I was able to create a Restore Point.

  Thank you very much for your message.

• iPhone disconnected during the software update

  My iPhone 5 has been connected to iTunes on my PC and I started a software update.  The phone disconnected during the update due to a bad cable.  Now my phone is locked to the screen update showing the apple logo.   I can't turn off it normally to reboot and iTunes does not recognize the phone when I plug it back on my PC.   Any ideas?

  Use the recovery mode as described here.  You may try to go into recovery mode more than once to succeed.

  If you are unable to update or restore your iPhone, iPad or iPod touch - Apple supports

• Password forgotten during the restoration

  Hello

  I bought a new iPhone6s. I already had an iPhone5. I downloaded itunes and saved the old device. Then I started the iphone 6 s. He asked me a few questions and I answered. He also asked me the password I entered (identical to the one I used for the iphone5, but with the last digit repeated 3 times). Then I plugged the device in itunes to restore and when I selected the restore from itunes the phone rebooted and asked me the password. I entered the password, but she did not accept it. I'm stuck now, the phone does not accept the password. I tried the way mentioned on the support of apple keeping the home button and the sleep/wake, but it won't go into restore mode.

  Is there another way to solve this problem?

  I tried the 'find my Iphone' on icloud, but it is not showing the phone the phone is locked and wifi and is not connected to a network.

  Any help would be much appreciated.

  When you set up your new phone, he should have asked for:

  1 language

  2. Wifi network

  3 iCloud connect

  4. then it should ask if you want to restore from an iCloud or iTunes backup

  Then, you should have Wifi at this stage.

  What is the text right of the message you receive about your access code? At what point in the process of this application it comes up?

  See you soon,.

  GB

• IPhone 5 do not restore no error message was given

  I have an iPhone 5, updated, as it was only of an update of last week when I got my new 6 s more, I tried several times to restore and update the 5 eveyrthing works well, the computer recognizes that the phone and a status even bar goes up on the phone, once its finished what happened then with the original message of "there is a problem with your iPhone" now the phone is stuck in recovery mode and I don't know what else to try! Help, please!

  What is happening in Recovery Mode? Try to do it this way to see if it allows you to complete:

  Turn off your iPhone.

  Connect the phone charging cable to the computer only (not for iPhone yet).

  Open iTunes on your computer.

  Hold the button to power on your phone and do not let go.

  Connect the cable to the phone while keeping the power button.

  Wait for the computer to detect the phone and wait that he eat.

  Restore first as New and then restore backup if you wish.

  If this does not work, try the DFU mode:

  http://www.IMore.com/how-to-iPhone-iPad-DFU-mode

• During the update Windows error 0 x 80070424 stops updating

  Original title: I canoe update error number 0 x 80070424 keeps coming
  I canoe update error number 0 x 80070424 continues next fixit center tried no joy

  Hello

  · You receive this error when you install a particular update?

  · What is the service pack installed on the computer?

  Try the methods below:

  Method 1:

  It is possible that certain windows update components are damaged.

  I suggest that reset you default windows update components and later try to install updates.

  See the below Microsoft article available tool and run the hotfix:

  How to reset the Windows Update components?

  http://support.Microsoft.com/kb/971058

   

  Method 2

  Disable the security software on the computer and check.

  Important: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 3:

  Visit the link, run the Fixit. You can also try other steps provided for in article.

  Error message 0 x 80070424 when you use Microsoft Update or Windows Update Web sites to install updates, or when you start Windows Firewall
  http://support.Microsoft.com/kb/968002

  Note: The above link is also applicable for Windows XP. Ignore method follow the steps in method 2 to 5 troubleshooting 1.

  Registry warning

  To do: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/)

  How to back up and restore the registry in Windows

• Update failed during the restoration of Win10 for Win7

  Hello

  There was a update failed while he was in the process of restore. Once the process is finished, I noticed that, so I clicked on "Install updates". Which also failed.

  I've never met update of the issues before the restore Win10 to Win7.

  Name of the update problem :

  -Microsoft .NET Framework 4.6.1 for Windows 7 for x 64 (KB3102433)

  Type of computer / OS :

  -Hewlett-Packard desktop computer bought in 2011, AMD Athlon (TM) II X 4 955 processor 3.20 GHz, 8.00 GB of RAM

  -Windows 7 Home Premium (preinstalled at the factory), Service Pack 1, 64-bit

  Antivirus applications installed before the upgrade and at a Win10; those after cancellation for Win7 :

  -Windows Defender (off)

  -Malwarebytes Anti-Malware free (do not prompt for reinstallation, update to Win10, have not opened since rollback)

  -AVG AntiVirus Free (relocation for upgrade to upgrade to Win10 successful, reinstall to update to Win7 after restoration, failure)

  Previous programs anti-virus installed / uninstalled :

  -factory pre-installed Norton Internet Security 2011 (60-day trial subscription). Uninstalled in 2011.

  -ISP provided security: Shaw Secure powered by F-Secure. Uninstalled in 2012.

  These are in the downloads folder (but I don't know more what/why and can't tell if they are installed programs or not) :

  -Windows-KB890830 - x 64 - V5.20.exe: Microsoft Windows Malicious Software Removal Tool, version 5.20.11000

  -msert.exe: no details of properties (no version, no digital signature, etc.), but I think that it is supposed to be the Microsoft Safety Scanner

  -windows-kb890830 - v3.21.exe: Microsoft Windows Malicious Software Removal Tool, version 3.21.5103.0

  -NPE.exe: Norton Power Eraser, version 2.0.0.52 the file, version 2.0 product, year 2011

  Latest updates successfully and the repetition does not install of KB3102433 :

  

  Error codes for KB3102433:

  -26/08/2016: 80200001

  -29/08/2016: 13EC

  -03/09/2016: 643

  -03/09/2016: 643

  Measures taken and the results:

  1) has no installation by the restore process: (KB3102433), 80200001 Code

  -revealed by timestamp in the update history

  (2) Windows Update interface: 1 important update available (KB3102433)

  -Click on install updates

  Result (s):

  -Failed / update history does not record the event

  3) of http://support.microsoft.com/kb/3102433

  -Download and run the "download the .NET Framework 4.6.1 (Offline install) package now"

  Result (s):

  -"Installation failed...". Fatal error during installation"

  -Updated story does not connect me

  (4) download and run the Windows 7 update (wu10.diagcab) troubleshooting tool

  Result (s):

  -Popup: An error occurred when troubleshooting: a problem is preventing start the troubleshooter.

  Identifier of the package: WindowsUpdateDiagnostic

  Path: unknown

  Error code: 0 x 80070002

  Source: engine

  User: (me, user Admin account)

  Context: restricted

  (5) run the System File Checker tool

  Result (s):

  

  (6) Windows Update interface: 1 important update available; KB3102433

  -Click on install updates

  Result (s):

  -This time the story recorded event update:

  Installation date: 29/08/2016

  Installation status: failed

  Error details: Code 13EC

  (7) download and run other troubleshooting of Windows 7 update (WindowsUpdateDiagnostic.diagcab)

  Result (s):

  -He scored a few points set except one:

  -"" Problems: Windows Update, error 0 x 80070057 do not set ""

  -This stage caused the update Interface to turn red on the theme and lose all it's information. such as:

  -1 important update available / 8 optional updates available <> before - now -online NO update available

  -Final check of updates: front: 29/07/2016 - now: never

  -Updates have been installed: front: 22/07/2016 - now: never

  -"Install updates" button "Check for updates" has disappeared, replaced by

  8) of http://support.microsoft.com/kb/3102433

  -Download and run the "download the .NET Framework 4.6.1 (Offline install) package now"

  Result (s):

  -"Installation failed...". Fatal error when installing... See log file»

  -Updated history do not log the event

  

  (9) click on ' Check for updates ' hopefully bring "updates available".

  Result (s):

  -He kept checking for about 2 hours without change

  -I didn't know how to cancel the verification process, then...

  (10)... Computer restarts

  Result (s):

  -updates stops

  -Updated Interface:

  -Does not display available updates

  -Final check of updates: never

  -Updates have been installed: never

  * 3 days later, without getting any change, it automatically installed 9 updates successfully. Now, the update Interface is once again changed. "Show all available updates" option appears, horodateurs, replacing '' never. ''

  (11) select problem update (KB3102433), and then click on install

  Result (s):

  -A failed; Error Code 643

  -Click on 'Try' again: same results

  Any help would be greatly appreciated.

  Thank you

  Proceed as follows: Set "Never search updates" automatic updates, restart, and try again.

  Best regards, VZ :)

• Apps on my ipad has disappeared; reappear briefly during the restoration, and then disappear again.

  I'm in IOS 9.2.1 on an iPad Mini 2, implemented to date (January 31, 2016.) Before the update, I noticed that he lacked all default applications. Projector showed the apps, but the 'Open' button was grey out. The app store shows install them on the iPad. I tried factory - reset several times, and then restored the backup, but one of the two following situations occurs:

  (1) the restore happens and each application icon to load, it disappears as soon as the loading is complete. In the end, we're back to where we were this morning, with only the default apps available.

  (2) the startup "Hola" white brand new screen, while iTunes tells me that everything is back on the iPad.

  Any suggestions?

  Thank you!

  You have an age category app defined in settings > general > Restrictions that could hide apps from your iPad home screen (which would be also grey keys 'open' for applications in the App Store)?

• Laptop stuck closed during the restoration of the system

  Laptop is stuck during the system restore? If I turn off computer manually by pressing the power button / stop it will mess up computer?  How can I fix it? The display shows 'Shutting Down' he was slaughtered like that for 2 hours now. Help, please?

  It is likely mean restoration of the system has failed for any reason any and therefore find it difficult to restart because of this.

  You may want to wait for someone a little more expert than me but normally peak I power the laptop through the main switch off and restart it.  At the start of the computer laptop once again he can ask you to start windows normally or in safe mode and you can then happily that we restart the PC and the system of cancellation/restore again.

• Running Exchange Server application of hotfixes and service pack to the server mailbox without loss of data during the restore?

  People,

  I would like to know how can I safely ask the Exchange Server service pack or cumulative update for the server role mailbox (no DAG) without loss of e-mail during the downtime and roll back the snapshot?

  If I can do the following:

  1. stop all Exchange Server services.

  2. unplug the vNIC on the mailbox server

  3 take a snapshot of the virtual machine

  4. apply the service Pack of Exchange Server / Cumulative Update or Windows Update

  5 reset

  6 reconnect the vNIC, if the server online with no problem, commit / remove the snapshot, if not, then disconnect the vNIC followed to restore.

  would be - this sense being or support for Vmware and Microsoft http://www.vmware.com/files/pdf/exchange-2010-on-vmware-support-and-licensing-guide.pdf ?

  If yu have any other suggestions, please let me know here.

  Thanks in advance.

  Hey AlbertWT,

  I'll start by saying that I would not do.  Microsoft is explicit that snapshots are not supported with Exchange when virtualized.  See below (from Exchange 2013 Virtualization: help Exchange 2013):

  Some hypervisors include features to take snapshots of virtual machines. Virtual machine snapshots capture the State of a virtual machine while it is running. This feature allows you to take several snapshots of a virtual machine and then return the virtual machine to a previous state by applying a snapshot to the virtual machine. However, virtual machine snapshots aren't application aware, and using them can have unintended and unexpected consequences for a server application that manages the data of the State, such as Exchange. Accordingly, making snapshots of the virtual machine to a virtual guest computer Exchange only is not supported.

  Even if we ignore the statement of support from shadow copies that isn't always a good idea.  Here are some things to consider.

  (1) cumulative updates for the Exchange to modify the Active Directory schema.  Roll back the snapshot on the mailbox server is not undo changes made to RFA, which could cause functional supported questions.  See this link to give you an idea of how there is pattern AD updates in each CU Exchange and service pack: the Active Directory in Exchange 2013 schema changes: Exchange 2013 help

  (2) it is possible to send to come during the time you test the update, and if you need to restore you would need a plan to retrieve this e-mail.  Third party services may work, or you can prevent the email to come in your environment completely during this period, but these aren't the ideal solutions.

  A much better solution would be to create a lab environment that is isolated from the production.  You can either take clones of your Exchange and AD VMs and put them in a closed network environment, or create a laboratory and import the structure of your ad if it matches the production.  I think it is a much better way to test than to try to rely on stereotypes in production.

  Hope that helps!

  Matt

• My mistake modem, during the restoration of the system of Windows 10 for Windows 7

  I have an update from Windows 7 to Windows 10, my laptop model is dell lnspiron 5010 32 bits.
  After returning on Windows 7 system, do not connect the modem driver error see the Internet and. Even with the installation of this driver, the problem persists.

  Please advise and help me.

  With special thanks

  Hello

  Thanks for posting your query to the Microsoft forum.

  I understand that you are facing problems with your internet connection, I will definitely help you with this problem.

  I would like to know;

  Do you receive an error message/code when connecting to internet?

  This issue could result due to these reasons:

  • This problem may occur if you already have an active broadband connection.

  • This problem may occur when another device with a driver that is not compatible with Windows 7 is in conflict with the modem.

  Please try these methods below and check the status of the issue.

  Method 1: run it Network troubleshooting.

  Try to run the Network Troubleshooter that can help you solve the problems with the internet connection.

  Using the troubleshooter from network in Windows 7

  If the problem persists, follow method 2.

  Method 2: Remove and re-create the wireless network connection.

  To remove and re-create the wireless network connection, follow these steps:

  1. Press the Windows key on the keyboard > type ncpa.cpl , and then press on ENTRY.
  2. Right-click your wireless network connection and then click Properties
  3. Click the wireless networks tab.
  4. Under preferred networks, click your wireless network, and then click Remove
  5. Click view wireless networks.
  6. Under the management of the network, click Refresh network list.
  7. Under Choose a wireless network, click the wireless network to which you want to connect, and then click on connect.

  If the problem persists, follow method 3.

  Method 3: I suggest you follow the procedure described in the given Microsoft help articles below:

  Wireless and wired network problems

  How can I troubleshoot network card?

  Additional information:

  Why can't I connect to the Internet?

  Method 4: Access your room Safe mode with network.

  Steps for starting mode safe mode with networking on Windows 7.

  1. remove all floppy disks, CDs and DVDs from your computer and restart your computer.

  • Click the Start button, click the arrow next to the button stop and then click on restart.

  2. do one of the following:

  • If your computer has a single operating system installed, press and hold the F8 key as your computer restarts. You need to press F8 before the Windows logo appears. If the Windows logo appears, you need to try again by waiting until the Windows logon prompt appears, and then stop and restart your computer.
  • If your computer has more than one operating system, use the arrow keys to select the operating system you want to start in safe mode, and then press F8.

  3. in the display Advanced Startup Options , use the arrow keys to select the option networking in safe mode , and then press ENTER. For more information about the options, see startup options (including safe mode).

  4 log your computer with a user account with administrator rights.

  When your computer is in safe mode, you will see marked Safe Mode in the corners of your screen. To leave safe mode, restart your computer and let Windows start normally.

  See the link below: , start your computer in safe mode

  Please post back with the results and the information requested, we will be happy to help you further.

  ____________________

  Thank you best regards &,.

  Isha Soni

• How can I fix error - 1 during the restoration of the iphone(5's)? Thanks in advance to all who will give answers.

  I always encounter error - 1 when I try to restore my iphone. I would like to ask for help at all, which is error-1, which makes and how will definitely be to remedy. Thanks in advance to all.

  Try these steps first If you find an error when you update or restore your iPad, iPhone or iPod - Apple Support