iPhone - ASA VPN connects and gets disassembly

Hello world...

I have a VPN working properly on a 8.0 (5) ASA, but when I try to connect from an iPhone (IOS 5.1.1) it connects and immediately Gets a teardown.

Any thoughts?

Thank you!

can you pls share your config ASA and advise what group policy, you use for iphone users?

Tags: Cisco Security

Similar Questions

Site to Site between ASA VPN connection and router 2800

I'm trying to get a L2L VPN working between a ASA code 8.4 and a 2800 on 12.4.

I first saw the following errors in the debug logs on the side of the ASA:

Error message % PIX | ASA-6-713219: KEY-GAIN message queues to deal with when
ITS P1 is complete.

I see the following on the end of 2800:

ISAKMP: (0): treatment charge useful vendor id
ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 157
ISAKMP: (0): provider ID is NAT - T v3
ISAKMP: (0): treatment charge useful vendor id
ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 69
ISAKMP (0): provider ID is NAT - T RFC 3947
ISAKMP: (0): treatment charge useful vendor id
ISAKMP: (0): treatment of frag vendor id IKE payload
ISAKMP: (0): IKE Fragmentation support not enabled
ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
ISAKMP: (0): former State = new State IKE_R_MM1 = IKE_R_MM1

ISAKMP: (0): built NAT - T of the seller-rfc3947 ID
ISAKMP: (0): send package to x.x.x.x my_port 500 peer_po0 (R) MM_SA_SETUP
ISAKMP: (0): sending a packet IPv4 IKE.
ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
ISAKMP: (0): former State = new State IKE_R_MM1 = IKE_R_MM2

ISAKMP (0): packet received from x.x.x.x dport 500 sports global (R)

MM_SA_SETUP
ISAKMP: (0): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
ISAKMP: (0): former State = new State IKE_R_MM2 = IKE_R_MM3

ISAKMP: (0): processing KE payload. Message ID = 0
ISAKMP: (0): processing NONCE payload. Message ID = 0
ISAKMP: (0): found peer pre-shared key x.x.x.x corresponding
ISAKMP: (2345): treatment charge useful vendor id
ISAKMP: (2345): provider ID is the unit
ISAKMP: (2345): treatment charge useful vendor id
ISAKMP: (2345): provider ID seems the unit/DPD but major incompatibility of 54
ISAKMP: (2345): provider ID is XAUTH
ISAKMP: (2345): treatment charge useful vendor id
ISAKMP: (2345): addressing another box of IOS!
ISAKMP: (2345): treatment charge useful vendor id
ISAKMP: (2345): vendor ID seems the unit/DPD but hash mismatch
ISAKMP: receives the payload type 20
ISAKMP (2345): sound not hash no match - this node outside NAT
ISAKMP: receives the payload type 20
ISAKMP (2345): no NAT found for oneself or peer
ISAKMP: (2345): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
ISAKMP: (2345): former State = new State IKE_R_MM3 = IKE_R_MM3

ISAKMP: (2345): sending package x.x.x.x my_port Exchange 500 500 (R)

MM_KEY_EXCH

----------

This is part of the configuration of the ASA:

network of the ABCD object
10.20.30.0 subnet 255.255.255.0

network of the ABCD-Net object
172.16.10.0 subnet 255.255.255.0

cry-map-77-ip object-group XXXX object abc-site_Network allowed extended access list

access list abc-site extended permitted ip object-group XXXX object abc-site_Network

ip access list of abc-site allowed extended object abc-site_Network object-group XXXX-60

NAT (any, any) static source 20 XXXX XXXX-20 destination static abc-site_Network abc-site_Network

NAT (any, any) static source 20 XXXX XXXX-20 destination static abc-site_Network abc-site_Network

XXXX-20

object-group network XXXX-20
ABCD-Net network object
object-abcd-Int-Net Group

XXXX_127

object-group network XXXX-20
ABCD-Net network object
object-abcd-Int-Net Group

ip access list of abc-site allowed extended object abc-site_Network object-group XXXX-60

Crypto card off-map-44 11 match address cry-map-77
card crypto out-map-44 11 counterpart set 62.73.52.xxx
card crypto out-map-44 11 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

cry-map-77-ip object-group XXXX object abc-site_Network allowed extended access list

Crypto card off-map-44 11 match address cry-map-77
card crypto out-map-44 11 counterpart set 62.73.52.xxx
card crypto out-map-44 11 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

card crypto out-map-44 11 set transform-set ESP-3DES-SHA ikev1

object-group network XXXX
ABCD-Net network object
object-abcd-Int-Net Group

------------------------

Here is a part of the 2800:

!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
ISAKMP crypto key r2374923 address 72.15.21.xxx
!
!
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
!
card crypto cry-map-1 1 ipsec-isakmp
the value of 72.15.21.xxx peer
game of transformation-ESP-3DES-SHA
match address VPN
!
type of class-card inspect match class-map-vpn
game group-access 100
type of class-card inspect cm-inspect-1 correspondence
group-access name inside-out game
type of class-card inspect correspondence cm-inspect-2
match the name of group-access outside
!
!
type of policy-card inspect policy-map-inspect
class type inspect cm-inspect-1
inspect
class class by default
drop

type of policy-card inspect policy-map-inspect-2
class type inspect class-map-vpn
inspect
class type inspect cm-inspect-2
class class by default
drop
!

!
interface FastEthernet0
IP address 74.25.89.xxx 255.255.255.252
NAT outside IP
IP virtual-reassembly
security of the outside Member area
automatic duplex
automatic speed
crypto cry-card-1 card
!
interface FastEthernet1
no ip address
Shutdown
automatic duplex
automatic speed
!
IP nat inside source overload map route route-map-1 interface FastEthernet0
!
IP access-list extended inside-out
IP 172.16.10.0 allow 0.0.0.255 any
IP nat - acl extended access list
deny ip 192.168.0.0 0.0.255.255 172.16.10.0 0.0.0.255
deny ip 10.200.0.0 0.0.255.255 172.16.10.0 0.0.0.255
deny ip 192.168.0.0 0.0.255.255 172.16.10.0 0.0.0.255
deny ip 0.0.255.255 28.20.14.xxx.0.0 172.16.10.0 0.0.0.255
refuse the 10.10.10.0 ip 0.0.0.255 172.16.10.0 0.0.0.255
refuse the 172.16.10.0 ip 0.0.0.255 192.168.0.0 0.0.255.255
refuse the 172.16.10.0 ip 0.0.0.255 10.200.0.0 0.0.255.255
refuse the 172.16.10.0 ip 0.0.0.255 192.168.0.0 0.0.255.255
refuse the 172.16.10.0 ip 0.0.0.255 28.20.14.xxx.0.0 0.0.255.255
refuse the 172.16.10.0 ip 0.0.0.255 10.10.10.0 0.0.0.255
allow an ip
outside extended IP access list
allow an ip
list of IP - VPN access scope
IP 172.16.10.0 allow 0.0.0.255 192.168.0.0 0.0.255.255
IP 172.16.10.0 allow 0.0.0.255 10.200.0.0 0.0.255.255
IP 172.16.10.0 allow 0.0.0.255 192.168.0.0 0.0.255.255
IP 172.16.10.0 allow 0.0.0.255 28.20.14.xxx.0.0 0.0.255.255
IP 172.16.10.0 allow 0.0.0.255 10.10.10.0 0.0.0.255
IP 192.168.0.0 allow 0.0.255.255 172.16.10.0 0.0.0.255
IP 10.200.0.0 allow 0.0.255.255 172.16.10.0 0.0.0.255
IP 192.168.0.0 allow 0.0.255.255 172.16.10.0 0.0.0.255
28.20.14.xxx.0.0 0.0.255.255 ip permit 172.16.10.0 0.0.0.255
ip licensing 10.10.10.0 0.0.0.255 172.16.10.0 0.0.0.255

access-list 23 allow 192.168.0.0 0.0.255.255
access-list 23 allow 10.200.0.0 0.0.255.255
access-list 23 allow 172.16.10.0 0.0.0.255
access-list 123 note category class-map-LCA-4 = 0
access-list 123 allow ip 192.168.0.0 0.0.255.255 172.16.10.0 0.0.0.255
access-list 123 allow ip 10.200.0.0 0.0.255.255 172.16.10.0 0.0.0.255
access-list 123 allow ip 192.168.0.0 0.0.255.255 172.16.10.0 0.0.0.255
access-list 123 allow ip 0.0.255.255 28.20.14.xxx.0.0 172.16.10.0 0.0.0.255
access-list 123 allow ip 10.10.10.0 0.0.0.255 172.16.10.0 0.0.0.255
access-list 123 allow ip 172.16.10.0 0.0.0.255 192.168.0.0 0.0.255.255
access-list 123 allow ip 172.16.10.0 0.0.0.255 10.200.0.0 0.0.255.255
access-list 123 allow ip 172.16.10.0 0.0.0.255 192.168.0.0 0.0.255.255
access-list 123 allow ip 172.16.10.0 0.0.0.255 28.20.14.xxx.0.0 0.0.255.255
access-list 123 allow ip 172.16.10.0 0.0.0.255 10.10.10.0 0.0.0.255
!
!
!

!
route-map-1 allowed route map 1
match the IP nat - acl
!

Hello

I quickly browsed your config and I could notice is

your game of transformation (iskamp) on SAA and router are not the same, try to configure the same on both sides.

in the statement of the ASA NAT you gave (any, any) try to give the name of the interface instead of a whole.

When I try to add a VPN connection, I get an error that the wizard is unable to connect. I am running Windows Vista.

When I try to add a VPN connection, I get an error that the wizard is unable to connect. I am running VISTA. I want to simply add a VPN and be able to connect to a non-profit organization where I volunteer. My VPN working two weeks ago. Then my shortcut did not work, and this problem started.

Any help is appreciated.

original title: VPN Vista issues

Hello

Thank you for visiting the Microsoft answers community site. Your question of Windows Vista is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the TechNet Windows Vista Networking forum.

http://social.technet.Microsoft.com/forums/en-us/category/windowsvistaitpro

I have created a VPN connection and it worked but you can't see how to remove Windows 7.

Delete the VPN connection

I have created a VPN connection and it worked but you can't see how to remove Windows 7. I tried rt-click but no delete option.

Open network and sharing Center. On the left side, click on change adapter settings. You will get all VPN connections that have been created and you can delete what you don't need.

Impossible to connect the printer to the laptop with a wi - fi connection and get a message saying "print spooler does not", even though troubleshooting it says that it is fixed.

Problems to connect a printer to my lap top using a wi - fi connection and get a message saying "print spooler not working do not ', even though troubleshooting it says it is fixed, any ideas please?

Original title: install a printer

I see an error message about "spooler" problems
A print spooler is software that temporarily stores the disk printing hard or in memory until the printer is ready to print.

If you were expecting an abnormally long time to print a document, or if you see an error message about the print spooler, you may have to restart the spooler to print on your computer.

To restart the spooler, the simplest method is to save your work and restart the computer. Alternatively, you can try the following steps:

To restart the print spooler service
1. You must be logged on as administrator to perform these steps.
2. Click Start, type: services , then press on enter on your keyboard
3. Double-click Services. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
4. Right click on the print spooler service, and then click Properties.
5. On the general tab, next to startup type, make sure that automatic is selected.
6. If the service is not already running, under Service status, click Start and then click OK. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

RV180 VPN connects and allows you to browse the files, but falls when opening a file.

Last week, we received our 300Mbps fiber connection. We bought the RV180 due to its high performance, and he manages the speed perfectly.

However, when you set up VPN, I encountered a strange problem.

Establishing a QuickVpn or PPTP is simple and connection is no problem. But I'll be fine. I can communicate with QuickVpn or PPTP and find a NAS or PC directory structure, but when I try to open a file the VPC connection drops.

I activate the remote management.
I can ping google.com f-l 1472 without fragmentation, so a WAN MTU of 1500 should be ok.
I have tried disabling attack prevention firewall.

I have install the following experience: the firmware update (1.0.2.6), restore the default settings.

Set up the RV180 as follows:

IPv4 WAN (Internet)

------------------------------------------------------------------

Internet connection type: Automatic Configuration - DHCP

DNS Server Source: Get dynamically for ISP

MAC address of the router: use the default address

IPv4 LAN (local area network)

------------------------------------------------------------------

Host name: RV180

IP address: 192.168.75.1

Subnet mask: 255.255.255.0

Mode DHCP: DHCP Server

Domain name: LCDVT

From the IP address: 192.168.75.100

End IP address: 192.168.75.254

Rental time: 24

DNS Proxy: enable

Preventing attacks

------------------------------------------------------------------

WAN (Internet) security controls

Meet Ping on WAN (Internet): disabled

Stealth mode: disabled

Floods: disabled

LAN (local area network) security controls

Block UDP Flood: disabled

Parameters of the ICSA

Block the anonymous ICMP Messages: disabled

Block fragmented packets: disabled

Block multicast packets: disabled

VPN users

------------------------------------------------------------------

PPTP server: enabled

From the IP address: 192.168.75.50

End IP address: 192.168.75.99

Table setting VPN Client:

---------------------------

No: 1

Enabled: enabled

Username: lcdvt

Password: *.

Allow the user to change the password: NA

Protocol: PPTP

Web access

------------------------------------------------------------------

Access on the LAN of HTTPS Web Interface: enabled

Remote management: enabled

Type of access: IP range

Start of range: 192.168.75.1

End of series: 192.168.75.254

Port number: 443

Remote SNMP: disabled

The rest of the menu options are, except for logging policies where I have everything turned on by default.

In this experiment, I connect from a remote location, start navigating among directories of the drive without any problems and then open a file, after which the VPN connection falls (or some process breaks down). After the transfer of a few 100 KB blocks the VPN connection.

Error logs

------------------------------------------------------------------

Thu Mar 20 00:39:18 2013(GMT+0100) [rv180] nimfNetIfaceTblHandler [System] [NIMF]: could not get LedPinId

Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] IP: 62.45.238.236

Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] BCAST: 62.45.239.255

Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] subnet: 255.255.254.0

Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] GW: 62.45.238.1

Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] DNS1: 62.45.45.45

Thu Mar 20 00:39:25 2013(GMT+0100) [rv180] [System] [PROGRAM] DNS2: 62.45.46.46

Thu Mar 20 00:39:25 2013 (GMT + 0100) [rv180] [System] [PROGRAM] Interface: eth1

Thu Mar 20 00:39:32 2013(GMT+0100) [rv180] nimfNetIfaceTblHandler [System] [NIMF]: could not get LedPinId

Thu Mar 20 00:40:58 2013(GMT+0100) [rv180] nimfNetIfaceTblHandler [System] [NIMF]: could not get LedPinId

Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] IP: 62.45.238.236

Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] BCAST: 62.45.239.255

Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] subnet: 255.255.254.0

Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] GW: 62.45.238.1

Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] DNS1: 62.45.45.45

Thu Mar 20 00:41:10 2013(GMT+0100) [rv180] [System] [PROGRAM] DNS2: 62.45.46.46

Thu Mar 20 00:41:10 2013 (GMT + 0100) [rv180] [System] [PROGRAM] Interface: eth1

Thu Mar 20 00:41:19 2013(GMT+0100) [rv180] nimfNetIfaceTblHandler [System] [NIMF]: could not get LedPinId

Warning logs

------------------------------------------------------------------

Thu Mar 20 00:39:13 2013(GMT+0100) [rv180] [System] [DHCPC] dhcpcDisable: removed dhclient.leases

Thu Mar 20 00:40:54 2013(GMT+0100) [rv180] [System] [DHCPC] dhcpcDisable: removed dhclient.leases

Sat 1 Jan 01:02:43 2011 (GMT + 0100) [rv180] [Kernel] [KERNEL] [23.090000] /home/aruns/rv180w/updated_dec19_final/beta-v1/rv180w-common/comps/gpl/ipset/src/ipset/kernel/ip_set.c: ip_set_create: no type set 'nethash', 'setPublicNet' has not created value

What I am doing wrong? Or the device?

I am interested in what the solution to these problems. Research on get a rv180...

First car of Huntsville and bike e-magazine: www.huntsvillecarscene.com

ASA VPN server and vpn client router 871

Hi all

I have ASA 5510 as simple VPN server and 871 router as simple VPN client. I want to have the user ID and permanent password on 871 and not to re - enter username and password since 871 uses dynamic IP address and every time I have to ' cry ipsec client ezvpn xauth "and type user name and password.

any suggestions would be much appreciated.

Thank you

Alex

Do "crypto ipsec client ezvpn show ' on 871, does say:

...

Save password: refused

...

ezVPN server dictates the client if it can automatically connect with saved password.

Set "enable password storage" under the group policy on the ASA.

Kind regards

Roman

VPN connects, cannot get to anything on the LAN

OK, what don't get me? My VPN connects OK with the Version of the Client 5.0.07.0290 VPN but I can't access anything on the 10.0.0.0/24 network.

Any thoughts? I should be able to ping the server 10.0.0.90 if it worked properly in my laptop while I'm on the VPN. Following configuration:

ASA Version 7.2 (4)

!

hostname XXXX

domain energy.com

activate jp28ZvYIS1PQVK6M encrypted password

UmzM9i7pSqpXEdTR encrypted passwd

names of

!

interface Vlan1

nameif inside

security-level 100

IP 10.0.0.9 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

IP address 74.x.x.150 255.255.255.248

!

interface Ethernet0/0

switchport access vlan 2

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

passive FTP mode

clock timezone IS - 5

DNS server-group DefaultDNS

domain energy.com

access-list 101 extended allow ip 10.0.0.0 255.255.255.0 192.168.150.0 255.255.255.0

access-list sheep extended ip 10.0.0.0 allow 255.255.255.0 192.168.150.0 255.255.255.0

outside_in list extended access permit tcp any host 74.x.x.146 eq 35330

outside_in list extended access permit tcp any host 74.x.x.147 eq 10000

outside_in list extended access permit icmp any one

outside_in list extended access permit tcp any host 74.x.x.148 eq 990

outside_in list extended access permit udp any host 74.x.x.148 eq 900

outside_in list extended access permit tcp any host 74.x.x.148 4000-4099

access-list extended outside_in permit udp any host 4000-4099 74.x.x.148

outside_in list extended access permit udp any host 74.x.x.148 eq 990

pager lines 24

Enable logging

timestamp of the record

exploitation forest-size of the buffer of 100000

debug logging in buffered memory

asdm of logging of information

Within 1500 MTU

Outside 1500 MTU

IP local pool dhcppptp-192.168.150.1 - 192.168.150.20

ICMP unreachable rate-limit 1 burst-size 1

ASDM image disk0: / asdm - 524.bin

don't allow no asdm history

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 0 access-list sheep

NAT (inside) 1 10.0.0.0 255.255.255.0

NAT (inside) 1 0.0.0.0 0.0.0.0

public static 74.x.x.146 (Interior, exterior) 10.0.0.90 netmask 255.255.255.255

static (inside, outside) 74.x.x.147 10.0.0.91 netmask 255.255.255.255

public static 74.x.x.148 (Interior, exterior) 10.0.0.3 netmask 255.255.255.255

Access-group outside_in in external interface

Route outside 0.0.0.0 0.0.0.0 74.x.x.145 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

GANYMEDE + Protocol Ganymede + AAA-server

RADIUS Protocol RADIUS AAA server

Enable http server

http 10.0.0.0 255.255.255.0 inside

http 192.168.1.0 255.255.255.0 inside

No snmp server location

No snmp Server contact

SNMP-Server Community public

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT

Crypto dynamic-map cisco 1 transform-set RIGHT

dynamic dyn-map 20-isakmp ipsec crypto map Cisco

dyn-map interface card crypto outside

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

md5 hash

Group 1

life 86400

crypto ISAKMP policy 30

preshared authentication

3des encryption

md5 hash

Group 2

life 86400

Telnet 10.0.0.0 255.255.255.0 inside

Telnet timeout 5

SSH 0.0.0.0 0.0.0.0 inside

SSH 0.0.0.0 0.0.0.0 outdoors

SSH timeout 5

Console timeout 0

TFTP server inside 10.0.0.109 cpix.cfg

internal BEVPN group policy

BEVPN group policy attributes

Server DNS 10.0.0.4 value 10.0.0.1

VPN-idle-timeout 30

Split-tunnel-policy tunnelall

Split-tunnel-network-list value 101

maindomain.com value by default-field

disable authentication of the user

IPSec-attributes tunnel-group DefaultL2LGroup

pre-shared-key *.

IPSec-attributes tunnel-group DefaultRAGroup

pre-shared-key *.

ISAKMP ikev1-user authentication no

tunnel-group BEVPN type ipsec-ra

attributes global-tunnel-group BEVPN

address-pool dhcppptp pool

Group Policy - by default-BEVPN

IPSec-attributes tunnel-group BEVPN

pre-shared-key *.

ISAKMP ikev1-user authentication no

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

inspect the preset_dns_map dns

!

global service-policy global_policy

context of prompt hostname

Cryptochecksum:b379566df0e7f5213ad2396676763859

: end

Hello

I don't see the NAT0 configuration more in this configuration

NAT (inside) 0 access-list sheep

You can also change the ACL of Split Tunnel

standard access list permits 10.0.0.0 SPLIT-TUNNEL 255.255.255.0

BEVPN group policy attributes

no value of split-tunnel-network-list 101

Split-tunnel-network-list value of SPLIT TUNNEL

You can also use the "show run" command that will generate a little less production

-Jouni

ASA VPN connection cannot see all subnets

I'm new to the ASA and I have a problem with our remote users. When people access vpn, they don't see a couple subnets on the network. I looked at the ASA and he can see and communicate with subnets, but when you vpn in them is not reachable. All these connections are connections from admin to admin privlages. Anyone know why the ASA can see subnets, but the admin vpn users cannot?

You compare your ACL split tunnel and your table routing, but only for networks that are relevant to you and you must have access to and are not outside the old configuration. You should also ensure that these networks can route traffic from the pool of vpn.

ASA in ASA VPN-encrypted packets "get lost" in the tunnel

Hello

We have a VPN site-to site between ASAs. Both on the v9.1.6 code. On distance ASA, it also has to do NAT source and destination. We see the traffic 'interesting' made from the results of the remote side in ipsec SA. Late has ITS correspondent. Corresponding spinnakers. However, the remote end HIS watch packets encrypted, decrypted none. Late ASA shows no packets encrypted/decrypted. So, how can I "lose" packages in my VPN tunnel if both ends have matching SAs/SPIs?

Best regards

Richard

Hello

Could be incorrect rules NAT or an access list refusing ESP packets somewhere in the path between the two ASAs.

Can I insert a nano card into an iPhone 6 to activate and get him out?

I got an iPhone 6 or 6 s one of my friends. He said that I needed to provide my own sim card. I know that you use a sim card to activate the phone. In my case I will not use the iPhone as a real phone but like an iPod. I understand that the sim card doesn't have to be an active card. But it can not be disabled or theft. But my main concern is: can I insert the nano for the activation of start card and put it, I can remove it and it will still work without it in?

Note: I'm not 100% if the iPhone is a 6 or 6 s?

Yes. It takes a SIM card to activate the device with Apple. Once activated, you can remove it and use the iPhone as an iPod touch. Best thing to do is activate airplane mode, then go to settings, wifi and re - activate just wifi (this way the cellular radio stays turned off the power, since you do not in any case).

VPN connectivity and access software

Having records with XP machines connecting to windows server 2003 via VPN OK, but then cannot access software.

Greg,

You would be better served by asking this question in the Windows Server general forum , which is more suitable for computer scientists more while this customer's forum.
Maybe a moderator can move is here for you.

MowGreen
Expert in Windows IT Pro - consumer safety

* - 343-* FDNY
NEVER FORGOTTEN

ASA VPN client and OWA Exchange/2013

Hi all... quick question ASA...

Does anyone know the status of support for OWA Exchange 2013 and the ASA webvpn client access?

I know that the ASA has a model for 2010... It works with 2013? Is there is the 2013 model in the pipeline for the ASA?

Thank you!

Hi Paul,.

There is an improvement (CSCul27869) that opens to Exchange 2013 be supported with ASA.

CSCul27869
It is an enhancement request to add support for OWA 2013 with webvpn.
https://Tools.Cisco.com/bugsearch/bug/CSCul27869/?reffering_site=dumpcr

Kind regards
Dinesh Moudgil

PS Please rate helpful messages.

What should I do if I want to only temperarily access my favorites on a pc in an Internet Café? Is it an option for the removal of the device to remove the pc? Or I can connect and get my selected favorites and I logout and mozilla back? Help, please.

I love mozilla...

Hi meltingheart,

If I were you, I'd take a peek at http://portableapps.com/ . I think it will be exactly what you are looking for. It allows you to run a version of Firefox (and other great programs) which are all on a small thumb thumb USB key. In this way, you have access to all your bookmarks firefox and tools everywhere you go. As soon as you unplug the drive, you take all your data user with you so he won't let any of your private information on your computer.

I have a small USB attached to my keychain that I use for these purposes. It's pretty impressive!

SSL VPN 25 user license - impossible to get more than 2 SSL VPN connections

Hello

I just installed a user license user Premium 25 for SSL VPN on my Cisco ASA5505. Even though it states that the license is installed I get still only two client Anyconnect SSL VPN connections and the third fails systematically. What Miss me?

Thanks for posting to the forum and that the problem has been resolved, and what caused the problem and what has been done to solve the problem. It's the most useful forum when people can read on a problem and can also read what the problem turned out to be and what was done to solve the problem, I think that it is also a good example to remind us that sometimes, the problem is not in our configuration, or even in the area that we administer. So sometimes we have to look beyond our normal home to find the source of the problem.

The question mark it resolved makes it even more obvious to readers that they will find a solution to the problem. So thank you to mark the issue as resolved.

HTH

Rick

iPhone - ASA VPN connects and gets disassembly

Similar Questions

Maybe you are looking for