Ipiel-la3 rev: 1.01 bios update (P6150NL)

Similar Questions

• HP Pavilion elite e9000 (mother of IPIEL-LA3) - updated bios for RAM w / 4 GB DDR?

  Hello

  I bought a computer (custom config) Pavilion elite e9000 of costco in 2009, so I've offended have an exact model in 31 configurations HP number has for this model in the software support.  He had 6 GB (3 x 2 GB) DDR3 ram on a motherboard with Intel Core 2 Quad CPU @2.5 GHz IPIEL-A3...  Bought with Vista, now under Windows 7 64-bit

  Trying to speed up the computer (vs upgrade) and from what I can tell, 4 GB of RAM chips are not compatible with the motherboard.

  Try to understand if a BIOS upgrade would work, but the card BIOS upgrade mother IPIEL-LA3 throws an error 253.

  Y at - it an update to software that I can do to allow me to update the RAM (like to go to 12-16 GB of my 6 today)?

  Here are the specifications and configurable options for your desktop HP Pavilion Elite e9110t. Here are the specs because that's card mother IPIEL-A3 (Eureka3). According to specifications, your system supports the following memory configurations;

  Four DDR3 DIMM sockets (240 pin)

  Supports DIMM DDR3 2 GB modules

  Supports dual channel memory architecture

  PC3-8500 1066 MHz

  PC3-6400 800 MHz

  Memory non - ECC, unbuffered

  Supports up to 8 GB on 64 bit computers

  Supports up to 4 GB on 32-bit computers

  4 GB DDR3 DIMMS are not supported by this system. It's usually because that material (chipset) does not support sizes larger than those listed. In rare cases the limitation may have been imposed by HP in the BIOS. The update of the BIOS address not to increase the size memory or questions. Error 253 means that the BIOS is not for your system or your system does not meet the minimum requirements of the update. If you want to install the update in safe, you must install it to Vista.

  BIOS update 'sp43102.exe' requires a Microsoft Windows Vista operating system installed.

  Exit the: 2009-08-03

  Version: 5.05

  Compatibility: Microsoft Windows Vista, Microsoft Windows Vista (64-bit)

  Fix/development:
  Resolves a problem with USB not detected mass storage devices.

  Updates the boot order to place the optical drive before the hard drive.

  Resolves a problem with memory cards UDMA Ultra Direct Memory Access () see the incorrectly in Windows.

  Updates vBIOS to address issues HDMI.

  Updates the strategy thermal processor.

  Fixes an issue with the BIOS fault recovery if the card reader is connected.

• Clocked at 20 degrees warmer since putting on 3.87 Rev A Bios Update on Z420 Workstation

  I have a question:

  Not too long ago I put the Bios Update on A Rev 3.87 was considered to be as critical an update on my workstation Z420 (running Windows 7 Pro 64-bit), and lately I've found that the CPU idling at about 20 degrees more hot than before.  I used to hear creaking noises coming from the computer I learned normally come circuits on the motherboard power delivery, but as long as I heard those CPU would be on average around 50 degrees C at idle.  I hear these noises and now the CPU is on average around 70-75 degrees C at idle.  Not sure what the connection is.  HP performance Advisor tells me I'm in the normal range, but I want to just make sure that with programs like Autodesk Maya there, she become too hot and stop the machine.   I don't know what the temp high-end is considered maximum security.  This change could have due to the update of the Bios?

  Thank you for your response and suggestions.  I check in my BIOS power management settings has been developed the extended mode, but the temperature has always hovered around 70-78 degrees at idle.  I checked Intel spec for this (E5 - 1650 6-core xeon) processor, clocked at 3.2 Ghz by heart, and although he said nothing on the TMax, he mentioned that the TCase (which he defined as the maximum temperature allowed integrated processor heat sink (IHS)) was 64 degrees Celsius.  Now my temperature of the case, according to my HP Performance Advisor version 1.7.7517.0 is only about 24 degrees C, but I put my fan a little higher CPU, about 2009 rpm speed.  This makes a little more noise, but my CPU temp has dropped to about 49 °.  "" Before the change of the fan speed has been slightly more than 1300 RPM while the Advisor I have always said that it is in the range "normal".  Is it good to get the speed of the CPU fan like that or do I have to go a little lower?

  James Holman

• HP ProBook 6570b: Windows 10 ProBook 6570b BIOS update

  When will there be a version 10 of Windows to upgrade the BIOS (the more recent version, currently available for Windows only, 8.1 F.62 Rev.A, file name sp71172.exe) for my HP ProBook 6570 b?

  In fact, you can update using the file for Windows 8.1:

  1. Download the BIOS update sp71172.exe for Windows 8.1.
  2. Run, but do not select update now, but to create a USB key for update.
  3. Follow the instructions to create the USB key. This works on Windows 10.
  4. Reset.
  5. Access the configuration Menu by pressing ESC followed by F10.
  6. Find the option to update the BIOS on the USB key and follow the instructions.

• Spectrum x 360-15 t Touch mobile: new BIOS update

  How can I know if the BIOS update worked on my computer? I'm not sure if the update worked or not. What is the latest version of the BIOS for my computer? I downloaded the update to the BIOS of HP Support Assistant on my computer. After you download the new BIOS and then after rebooting, it does not show whether or not the update was installed. It is there no information about the update of all more. The BIOS update does not appear in the "action log" in the HP Support Assistant, so it makes me think that the update did not work?

  My product number is P0A42AV. The current Bios information shows that:

  F.08-06/16/2016.

  Whistlingdixiee wrote:
  

  How can I know if the BIOS update worked on my computer? I'm not sure if the update worked or not. What is the latest version of the BIOS for my computer? I downloaded the update to the BIOS of HP Support Assistant on my computer. After you download the new BIOS and then after rebooting, it does not show whether or not the update was installed. It is there no information about the update of all more. The BIOS update does not appear in the "action log" in the HP Support Assistant, so it makes me think that the update did not work?

  My product number is P0A42AV. The current Bios information shows that:

  F.08-06/16/2016.

  F.08 Rev.A (July 17, 2016) is the latest version of the BIOS available for your laptop.  If you need to see what version of BIOS that you are running, you can open the information system from the Start Menu or start utility in the BIOS (F10) to check.

  You can find all of this HP drivers/software on your computer, portable software & Driver Downloads page here.

• Compaq dc7800: DC7800 CPu id and BIOS update probem

  Hello

  My first post here, I hope you get what I'm trying to say.

  Well, I have this old compaq dc7800 sff and I managed to level it's OS to Windows 10.

  And now, I would like to update its bios and CPU id, but I can't run those exe, I downloaded on the cd7800 support site.

  I know that these bios update programs and so forth are not published for Windows 10, but I thought that windows7 versions would work.

  But they did not.

  For some reason, I got the the messege that "software publisher has refused to run this program on this computer.

  While this mean?

  I can't run these programs even with administrator privileges, I get the same messages?

  Because of Windows 10? Or what?

  The reason why I came across this problem was that I tried to update the CPU of the Q6600 to Q9550 and I got the error of CPU - ID firmware.

  Hello:

  It is very easy to update the BIOS on a dc7800 without being under Windows.

  In the menu of the BIOS on the file tab, there is a rom flash system command.

  All you have to do is put the BIOS files on a USB stick formatted with the FAT32 file system.

  Rather than go though all the steps to get the BIOS files, I've zipped or less than joint under attachments.

  Unzip them and copy the content of the file of the folder (not the folder), for your USB flash drive.

  Plug the flash drive into your PC and restart it, tap the F10 key to access the bios, select the file menu and on this list will be a rom flash system command.

  What to choose, and the PC will 'see' the files on the flash drive.  Follow the instructions on the screen to Flash the BIOS.

  I have attached files to the latest revision of the BIOS (1.32 Rev. A (6 Dec 2011)).

  If you still get the microcode error after updated the BIOS with the latest version, let me know, because then update the firmware, and it is a much more complex process.

• The Hewlett-Packard 786 7 v01.02 BIOS update

  Hello

  I installed a nvidia geforce gtx 560 card ti graph in the workstation HP xw4400 of my son as a Christmas gift, and I get the following error message:

  "Your computer's system firmware includes enough information to set up and use this.

  My understanding is that I need to update the BIOS, but I can't find an update for Hewlett-Packard 786 7 v01.02 on this site. I've attached a screenshot of system information.

  Thanks in advance for your support.

  The XW4400 is currently in the BIOS v2.07 Rev A, 8 December 2010 , but the history tab provides no story at all... so I can't find the old versions of BIOS and as such can't see if it's OK to jump directly from v1.02 to v2.07 without problem...

  But the tab notes relase v2.07 includes following:

  This package contains the system BIOS (BIOS family 7 786) and BIOS image the and remote flash utility for the HP xw4400 workstation. These utilities can be used to restore or update THE system BIOS. System BIOS is the operating system
  independent.

  If the BIOS linked above is for your XW4400 that uses the BIOS 786 7 family...

  But please note that the XW4400 has only updates for XP & VISTA and not Windows8. So the XW4400 updates may or may not work as expected when it is used with Windows 8. Both such and especially with a BIOS update that can be risky, I won't use the method of updating windows (HPQFlash) flashing the BIOS from version HPQFlash may not be completely compatible Win8... Instead, I would like to use the 'flash-BACK' or "BIOS CD" methods.

  You can learn more about the different methods of updating BIOS by looking at all the README files in sp51215.exe. You can either run sp51215.exe to unzip the contents of c:\swsetup\sp51215\ (but do not perform a bios update, just close the tool) or 7-zip to directly view the content of sp51215.exe...

  [edited to add following]

  Some other info on your error code 35 can be seen here and here.

  Seems that a pilot unit 35 error code can be fixed with a BIOS update, but only if the manufacturer has taken the trouble to make the necessary changes to properly allocate resources to the card...

  As a species at HP by doing as little work as possible, my still under warranty Z210 running Win7 Pro 64 bit has issues with Estate HDD support. The last driver from HP TSRI is version 10.6.0.1002, which plays well with my hard drives Estate because they appear as removable devices... Last iRST driver Intel 13.2.4.1000 does not support the "cougar point" such chipset used in my Z210 and causes weird problems when I Estate connected HARD drive (and sometimes when not connected)... But Intels TSRI version 12.9.0.1001 driver supports chipsets "cougar point" and so I can finally esata hard drive appears as removable devices...

  Unfortunately, HP has not bothered to update their drivers for centuries and they stay with a 10.6.0.1002 defective TSRI pilot... As you seem, HP wont always do the necessary work, and it's on a support and still under warranty machine... I call it "HP." Support '...

  The update of the BIOS may or may not help your situation, but in all cases, you have still some problems with drivers and the Windows 8 to settle as the XW4400 was never certified for Win8. You may need to perform a job detective to ensure that drivers, especially the chipset drivers, used during the Win8 installed and updates post install actually support the hardware itself... He is a guy to know what is the problem that the documents appear to be getting dumbed down and therefore, you will need to do a lot of reading...

  Otherwise, you could try to install a different generation or make card but a bike may have been a more easy Christmas gift...

  See you soon...

• WANT to 700-074: BIOS update failed HP ENVY 700-074

  I intend to update Windows 10 soon.  HP recommends to update the drivers and BIOS before upgrade.  the original BIOS is listed as FRIEND 80.15 in msinfo32 dated 19/09/2013 (and in the setup of the BIOS as KAI 80.15). The computer came with 8 VICTORY and has been updated to WIN 8.1.  I tried to update the BIOS with the update listed for computers 700 - 0xx WANT to sp66018.exe.  I downloaded and ran the update with the HP Support assistant help.  A DOS window appears, and the update completed.  Norton AntiVirus has been disabled and all programs were closed during installation.  I created a USB file as the recommended window.  After that restart the BIOS version has not changed... Even after several reboots (and stops) and disconnect the power cord (I did some housekeeping to clean the inside of the computer of the dust) the version of the BIOS is still the original.

  What is the correct BIOS update?  There are two listed for my machine - 80.20 Rev. (I used) may 28, 2014

  and 80.24 Rev.A 7 April 2015

  Which is the correct one?  I don't want to install a bad!

  It is possibly disable startup secure in the BIOS for the update to be successful?

  Apparently, the dates are correlated with the version I had.  I tried to install one, be one originally installed... I installed the 80.24 Rev A version dated April 7, 2015 and it updated without problems.

• HP EliteBook 8560p: HP EliteBook 8560p BIOS update F.63

  Problem with the HP EliteBook 8560p with Bios Update to F.63 RevA. After the download and installation failed message:

  The file system (C:\SWSetup\SP76205\ROM. CAB) BIOS update is missing or damaged. THE system BIOS does not update.

  How to solve this problem?

  First: download and try to install the Bios update F.63, it will fail - don't worry.

  Second: to check what type of the ROMA family and ROM date do you have, press F10 on the laptop at the start run the configuration utility and then view the file system information.  You should see: 68SCF or 68SCE, double check and write it on paper.

  Third: Start computer laptop back to Windows

  -go to C:\SWSetup\SP76206 and rename 68SCF or 68SCE in ROM (a single file if you aren't sure go to step: second)

  -go to C:\SWSetup\SP76206\hpqflash and rename 68SCF or 68SCE in ROM     (a single file if you aren't sure go to step: second)

  Finally:

  go to C:\SWSetup\SP76206 and do a HPQFlash right-click and run as administrator

  or

  go to C:\SWSetup\SP76206\hpqflash and do a HPQFlash right-click and run as administrator

  To sit and watch, do not touch your laptop up to the moment where you see Windows login.

• HP Pavilion XE763 BIOS update Release Notes?

  Work on the following machine:

  HP Pavilion XE763 with Phoenix BIOS revision of Basic 4.06 2.02 07/14/00

  ... and considering the BIOS firmware with this update:

  Dunidar wrote:

  I understand that you are looking for documentation of the HP Pavilion Cognac BIOS update. Unfortunately, the only information I can find on this update is located on the page I linked to you.

  I found the release notes.  Where everyone is looking to get this info, it's here:

  Technical release notes:
  ------------------------

  2.09 14/04/01
  (1) adds the control On / Off of FAN3 for rev b/j. H
  (2) support Simple Boot Flag

  2.10 20/04/01
  (1) changing the report option of CPU frequency for unlocked CPU (update of the standard rev 2.0)
  (2) edit the table above 1 GHz CPU speed

  2.11 07/19/01
  (1) display ID of FDI in manufacturing
  (2) fix error modem Cheetah under WinXP

  ... so it's not like they have added support for the USB boot.

• BIOS update issues

  I have a laptop Toshiba A - 215 Satellite & have a question.  In support of Toshiba for this laptop in particular, there are 6 - different versions of BIOS update.  Currently, I have the version installed in factory 1.00, dated 08/27/2007.  My question is is I meet any major problem, that you may know to download the 'versions of Flash ACPI & am I suppose to download the versions in increments-eg. version 1.30 to 1.50 & up to 2.00 maximum as well which is the latest version?

  Thank you for your help.

  Hi Thomas,

  First of all, why do you want to update the BIOS? I do not recommend updating BIOS whatsoever unless you ABSOLUTELY need for reasons such as: compatibility, fix bug, etc. Essentially, a BIOS update only if you want to solve a problem, you know for a fact is not fixable with a BIOS update. Don't just carelessly to the BIOS update. It is very dangerous. Today, we have systems dual-BIOS and precautionary measures, but it is still not recommended unless absolutely necessary.

  However, to also answer your question, when and if you need to update the BIOS, are always more later because it contains all fixes + all new the old BIOS rev has (unless of course the manufacturer removed something for stability purposes).

  Kind regards

  Patrick

• Update BIOS HP F.64Ap1 (8th bios update for my HP Envy laptop)

  What's new in this latest update of the bios? How is it important to install?

  Anyone?

  Thank you.

  Version F.64 Rev A - intermittent problem of bugs on system with two hard disks where re-partitioning the drive mSATA fires a blue screen event.

  Version F.63 - provides security improved for UEFI EDK2. NOTE: HP recommend transitioning to this BIOS update without delay.

• Downloaded the wrong BIOS update

  Hello, I'm val. It's my pc, http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4063&lc=en&cc=us&dlc=en&sw_lang=&product=5071... I downloaded updated bios wrong, H-RS880-ΜATX Motherboard BIOS update which I discovered that my mother board need to update BIOS of motherboard of N-Alvorix-RS880 and I am on this computer now it works very well the only difference I noticed is after I started my computer and log I get a black screen for a while until Windows explore lights, which takes more time to do this, I usually start to the top of the Explorer windowse myself. whenever I'm trying to download the N-Alvorix-RS880 motherboard BIOS update it gives me the bios image 252 error code is invalid or damaged. I have no idea of what having the wrong bios update will do to my computer but I keep my computer on at all hours of the day. I've been looking online and I see computer most people becomes useless and I wonder why mine is not useless, but in any case I hoping to get help, please save me to things I am aware of a .

  Hello Valentink,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I understand that you believe that you have installed an incorrect BIOS update on HP Pavilion Elite HPE-510y desktop PC. I checked and the two BIOS updates you link to are for your computer, the only difference is the version the update of the BIOS of motherboard ΜATX-RS880-H is Version 6.11 Rev has what is more recent, then the N-Alvorix-RS880 card motherboard BIOS update which is Version 6.07 Rev A. You cannot install the second update is because the you have a more recent version.

  I wouldn't worry have the incorrect BIOS up-to-date is one you have for the computer. As you can see on the page the two updates BIOS Drivers of HP Pavilion Elite HPE-510y desktop PC are listed for your computer.

  I hope that I have answered your question to your satisfaction. Thanks for posting on the HP Forums. Have a great day!

• bios update Pavilion a1340n

  I have a HP Pavilion a1340n with XP, I want to use Windows 7 but I can't because I need to update the bios, I am looking for the update but I can't find, then, where I can download the bios update? If you have a solution please send me a message to my email address is [removed personal information]

  It's the current properties *.

  BIOS type: FRIEND BIOS

  Date: December 26, 2005

  BIOS ID: 63-0100-000001-00101111-122605-RS400-RC410-Mg

  OEM BIOS: BIOS

  Date: 26/12/2005 - 3.06

  Chipset: VIA 82 3044 rev 128

  SuperIO: ITE 8712F rev 7 002nd Port

  Manufacturer: HP Pavilion 061

  Motherboard: EL470AA-ABA A1340N

  erosfaus wrote: I have a HP Pavilion a1340n with XP, I want to use Windows 7 but I can't because I need to update the bios, I am looking for the update but I can't find, then, where I can download the bios update? If you have a solution please send me a message to my email address is [removed personal information] it's the current properties *.

  Type of BIOS: FRIEND BIOS Date: 26 December 2005 BIOS ID: 63-0100-000001-00101111-122605-RS400-RC410-Mg

  OEM BIOS: BIOS Date: 26/12/2005-3.06 Chipset: VIA 82 3044 SuperIO 128 rev: rev ITE 8712F 002nd port 7

  Manufacturer: HP Pavilion 061 Motherboard: EL470AA-ABA A1340N

  Hello erosfaus, here is the link for the specifications of your system. Since you don't mention which version of Windows 7 (32-bit or 64-bit) you want to install on your system, you may want to download and run the Windows Upgrade Advisor to see if your system can be upgraded to Windows 7.

  I also checked for an update of the BIOS and did not find one for your system.

  Because your system was shipped with Windows XP, you would not be able to upgrade to Windows 7, but be required to perform a new installation. It is of course, if your system can be upgarded to Windows 7.

  Here is the link for Windows Upgarde Advisor.

• Satellite X 200-20 s - LAN does not work after BIOS update

  Hi all

  I've updated the BIOS version 2.7 and NIC LAN just disappeared from my list of device. The wireless network card works fine however. When I plug the ethernet cable, the green light turns orange not, so I guess that it is not broken, as it worked fine before the BIOS update.

  I tried different drivers lan Windows XP and still nothing. Any ideas please?

  I have Windows 7 x 64 installed.

  LAN option is listed in the BIOS boot menu?

  If you have tested with Win7 and WXP maybe you should do finally test and install recovery image original Toshiba that you got with your laptop and see what happen when you use the laptop with the factory settings.