Is it a bad idea to use ICS on a Windows 98 computer for a Vista laptop to connect to the local network?

Similar Questions

• cannot connect to the local network using windows 7

  Recently bought a HP Pavilion laptop (AMD Athlon II P320 Dual - Core) ((G62 - 208CA)). Having a problem connecting to the local network. I have flashing lights on the lan (orange and white) connector.

  Using the ipconfig command, I get an IP address, subnet mask and gateway by default however messages below will appear:

  Tunnel adapter isatap. <578608BD-22EF-4A01-90ED-D709CB81D027>:

  State media: media disconnected

  The connection-specific DNS suffix. :

  Tunnel connection to the Local network adapter * 9:

  State media: media disconnected

  The connection-specific DNS suffix. :

  Tunnel adapter isatap. :

  State media: media disconnected

  The connection-specific DNS suffix. :

  TEREDO TUNNELING Pseudo-Interface tunnel adapter:

  State media: media disconnected

  The connection-specific DNS suffix. :

  Tunnel adapter isatap. our field: *

  State media: media disconnected

  The connection-specific DNS suffix. :

  I tried to turn off the firewall and connect without success

  My network card is a Realtek PCIe FE Family Controller and confirmed that the drivers are up to date

  Any help would be appreciated

  Thank you

  Well Yes! So it was an older version of the bonjour service... thank you Adobe.

  You can find the latest version here:

  http://support.Apple.com/kb/DL999

• Connected to the local network, but can not use internet

  I recently had problems with access to the internet after reinstalling windows 7. Before the reinstall worked very well.

  I can connect to the local network without problem, and it shows that the internet is connected. Yet I can not access the internet. When I disconnect and reconnect, I get a few seconds of internet work before it stops working.

  When a diagnosis in the network and sharing Center, I get the error "default gateway is not available" and occasionally "the connection between your access point, etc. and internet is broken"

  Other computers and devices using the network are working properly, although there was a 'competitor IP address' error on another pc, which, after a reconnection, solved itself.

  I use an edimax 802.11n wireless card and a D-link router

  I tried several things to make it work again, but without result. Any help would be greatly appreciated

  disable TCP/IPv6 had no effect.

  I think I can have fixed me, I installed the driver microsoft before the reinstall instead of the driver edimax and internet suddenly started working.

  Thanks for the help of yor

• can I use 4 monito in windows 7 computer for tense office

  can I use 4 monito in windows 7 computer for tense office

  Your terms "Extended Desktop" are ambiguous, as you have not provided sufficient details with your question.

  The correct terminology is "Desktop Extension" or "Desktop covering.  It is important to note that these are two things a little different.  Fully answer your question, it is necessary to describe the differences.

  Others that by activating the special modes provided by the specific video drivers on the special cards, Windows 7 does not support Desktop covering.  The WDDM (Windows Display Driver Model) for Windows 7 does not have The Extension Office.

  The Extension Office differs from Office covering that with Extenstion Desktop games will not mode "full screen" on all screens.  Also, you will see the taskbar on only one of the monitors, and will maximize demand for only the full monitor on which it resides when you press the expand button.  However, it is possible to resize a window on multiple monitors.  Also, it hosts capabilities and monitors of different resolutions.

  Apart from the games and their preferences for the maximization of the app, Desktop Extension is very useful.

  According to me, is it possible to use The Extension Office - a collection of video equipment - extend your Windows 7 Desktop in any number of monitors, although I have only used it with two monitors myself.

  -Christmas

  P.S. on the chances that your question is about a desktop image stretching on several monitors: Yes, you can do it.  Create a desktop image that is the size, in pixels, of the horizontal and vertical of the desktop space, and select 'Tile' mode when you set the background.

• Connect two VMs via the connection to the local network using VMWare Player

  So this topic can be posted already, but I'm at the end of the roll, trying to find a solution. I have VMWare player installed 3.1.4 on an enterprise_x64 of Windows 7 system. I configured two virtual machines: OS1 comments: Red Hat Enterprise Linux Server 5.5_x64 and OS2 comments: WIndows 7 Ultimate_x64. I need the Linux server to act as a database server in the system environment, that I am creating. The Windows 7 VM will be the client PC. The Linux server is configured to be it's own DHCP server, so ideally the client PC connects to the field of tht and also follow the Linux server IP address.

  I tried all the options of networkign for each virtual computer, but no sem to create this type of connectivity. How to configure the network settings in VMWare Player to make two virtual computers can communicate with each other via a virtual network? (Communication with the host pc is not necessary)

  The short answer is to manually install the lack vmnetcfg.exe, Editor of virtual networkand configure VMnet2 without DHCP and host vNIC and then configure manually each virtual machine network adapter to use Custom VMnet2.

  The longer answer has already been given so many times that you should be able to find detailed directions, however...

  To install the lack vmnetcfg.exe, virtual network editor, run VMware-player-* .exe-e c:\vmptmp go to a command line and then in the c:\vmptmp folder, locate the file c:\vmptmp\network.cab and extract (double-click on the .cab file) vmnetcfg.exe (virtual network editor) file in the working directory of VMware Player usually ' C:\Program Files\VMware/VMware Player ' you can create a shortcut to it and place it with the shortcut of VMware Player if you want to access more easily to her.  This utility is not installed by default is however necessary to turn off the automatic bypass on VMnet0 if the system is multihomed and two or more physical host from the NETWORK adapter is active or you want change VMnet1 and VMnet8 subnet addresses or additional VMnets.

  The you must manually change the configuration of each virtual machine's .vmx file in Notepad, change an existing parameter and add another.

  Change:

  ethernet0.connectionType = "nat"
  

  TO:

  ethernet0.connectionType = "custom"
  

  Add:

  ethernet0.vnet = "VMnet2"
  

  Note: Regardless of connectionType ethernet (n) shows it should be changed to "custom".

  Be sure also to Machine virtual are stop, not suspended and VMware Player is closed when you edit the .vmx config files.

  Here are some pictures to show.

  Here in the VMnet2 virtual network Editor is selected and is how it should be if you what to use your own DHCP server and the host does not have a vNIC.  You can change the IP address as a result of your needs.

  

  Here's the value VM card network NAT settings.

  

  This is what network settings Virtual Machine map will look like after you change the configuration of the Virtual Machine's .vmx file to use Custom VMnet2.

  

  BTW if you replace the Machine network card virtual settings through the user interface customized by something else then you will need to manually edit the .vmx config file to retrieve.   With VMware Workstation, you do not need to manually install the virtual network editor and should not manually edit the .vmx config file as the custom list box is still present and shows all VMnets to select from.

• Cannot use the connection to the local network on Satellite A100-451

  I just bought an A100-451, but when I plug the LAN cable in no lights light up and I can't connect to the router, or configure the network connection?

  Help please?

  Please check if Device Manager the network adapter is properly enabled.

• Loading Windows Mail, I get a dial-up connection box. I am unable to change it to use my connection to the local network.

  original title: windows mail locks

  Loading windows messaging, I get a dial to the top of the connection box, when I go into properties, connections, accounts, the software locks so I can't change it to the connection of LAN so not e-mail. There is no dial-up access on this computer.

  Remove your e-mail account.  Then compact and repair the database (see www.oehelp.com/WMUtil/).  Then add your account to mail back again and see if its fixed.  Also pay attention to the problems of antivirus in WinMail: see www.oehelp.com/OETips.aspx#3

  Steve

• locking the computer: if not using computer for a while, it locks and requires the initial password to get in

  So do not use computer for a while, it locks and requires the initial password to get back in. When it becomes available, we've been thrown off internet, or another program we are.

  I don't know why Mr. Murphy suggested a system restore. Maybe he interpreted your post differently I did. You have your screen standby/power options defined on too short a time. You can also disable the requirement for a password during the recovery.

  Right-click on an empty area of the desktop and click on personalize. To customize the applet opens. Click the screen saver. Change the timeout to something reasonable like 10 or 20 minutes. You will see where you can clear the check box next to the "password required on curriculum vitae... ».

  Now do the same in the (Control Panel) Power Options applet. This link contains pictures showing you how to disable this option:

  http://www.mydigitallife.info/2008/06/29/disable-Windows-XP-and-Vista-from-asking-for-password-to-unlock-on-wake-up-resume-from-sleepstandby/

  MS - MVP - Elephant Boy computers - don't panic!

• Is it a bad idea to use more than 1 stylesheet?

  I have a lot of styles and want to organize a little better by placing them on different style sheets.  Is this a bad idea?  It will slow down the speed of the website?

  Whenever a different style sheet is loaded, that means a round trip to the server. Best practice is to optimize styles in a sheet, done all white spaces and comments.

  However, for simple sites, the speed difference is hardly noticeable and I tend to have on average about 4 CSS files by document.

  GRAMPS

• ASA 5510 VPN - using a public IP address for the local network

  Hello, I have a problem which is probably very simple, but I can't seem to understand.

  I set up a site IPsec connection to another with a company, something I've done many times before without a problem. I use ASDM to configure this, because it is quick and painless, usually.

  We have one number of other site-to-site currently configured connections and works very well on this ASA, these are configured with the "Protected network - LAN" configured with the IP private of hosts within our network, we want to make available through the separate tunnels. This includes the configuration setting on our ASA for each connection to "guests aside ASA exempt from NAT.

  With this new link, however, the company asked us to use a public IP address for the host that we want to achieve through the tunnel. I don't know why, but they demand it. So I added a NAT rule for inside the host and set up the connection with the public IP address under "Local network". During the test to try to reach a host to their side, the tunnel didn't even try to open.

  What is the method here? I don't see where I'm wrong. I'm guessing that the 'host side ASA exempt from NAT' does not require for this, how if the ASA would know which internal host is the public IP address.

  Any ideas?

  Hi Leo,

  The steps are:

  1. Add the policy rule NAT for the specific host.

  2 - define the IP NAT as your LOCAL NETWORK address in the encryption settings.

  3 make sure that there is no rule NAT exempt for this host to the specific destination.

  What happens if you run a package tracer?

  Thank you.

• in private browsing, I used to keep a sign in seal for yahoo, now it does not appear the sign of joint

  I used the incognito for over a year, I used to keep a sign in seal for yahoo, now the sign in the seal does not appear, how can I
  get the sign in seal to appear again?

  I change all the settings or stored anywhere, it stopped working today.
  It happened in the morning, I checked at 22:05, now it works again,
  Maybe something went past or somehow someone corrected the problem.
  Thank you for your quick response, thank you, best wishes to you all, lovely

• Want to make my Acer Aspire X 3475 able to use the connection to the wireless network

  How should I do and what wireless adapter to use? Modem/router is Netgear CG 3000.

  Hello

  I recommend the TP-Link boards PCIEx1 for your office.

  For example, this model: TP-LinkTL-WN781ND (including regular support and a low profile support).

• Dell support can make the diagnosis online on my computer damage water connected to the same network as the one I use now?

  HI: My Office has undergone a lot of overhead sprinklers water damage in my condo fire. I ordered a new power and it fuels the system very well, but I have no video and tried the video card of the computer another and it does not work. I can connect my alienware aurora to the same network with the computer that I use now. The warranty has expired. Any suggestions on my case? Thank you

  Our online diagnostics will not go to the bottom, you need. You must take the system at a local store. Must disassemble and examine most of its components in another system to try to dismiss what is defective or not. If all the components work in the other system, the CPU or the motherboard is faulty.

• Unable to connect to the SSID network which has the Double course using the command Netsh Wlan

  I tried to create a batch file that would connect to a wireless network, the name of the SSID is:

  simple "13."

  When I try to use the command:

  netsh wlan connect easy "13".

  It returns an error saying that the profile does not exist.

  I tried to use the following escape characters:

  netsh wlan connect easy \"13\.

  netsh wlan connect ' easy '13.

  But nothing seems to work and I can't find anything related on google. Can someone help me?

  Thank you

  Rene S.

  Hello René,.

  Thanks for posting your query in Microsoft Community Forum.

  You try to create a batch file to your question, I would say that you re - ask your question in the MSDN forum rather than on this forum. MSDN is watched by other computing professionals and developers who would more than likely be able to help.
  http://social.msdn.Microsoft.com/forums/en-us/windowsgeneraldevelopmentissues

  Hope this information is useful.

• I use a PC with Windows 10 and Lightroom 6.1.1. When in the develop Module of Lightroom freezes when I try to edit the next picture after correcting the first.

  I use a PC with Windows 10 and Lightroom 6.1.1.  As soon as I want to move from a photo retouched to another in the develop Module, Lightroom freezes.  Can you help me?

  Hi Petra,

  > Try disabling the option of GPU in the Lightroom > edit > Preferences > Performance tab

  > Update your graphics card driver

  Hope this helps

  ~ Assani