Issue of Black Line

Similar Questions

• thin horizontal black line down page what scan on HP Officejet Pro 8600 more

  I've owned an HP Officejet Pro 8500 and scan was perfect.  I recently bought a HP Officejet Pro 8600 Plus.

  When I scan from the ADF HP 8600, I get a thin (several pixel wide) black along the lower edge of the analysis that results.  This line will be sometimes slightly twisted or appear only through half of the page, in which case, it tends to become thicker towards the edge of the page).  According to me, this line is an artifact of the analysis of the edge at the bottom of the original document.  I think it is to show where the bottom edge of the page was when parsing.  If the document is that a little offset, then the black line down will be a little twisted, probably following the edge of the page.  This issue is consistent and reproducible.  It is in the mode "Scan mail" and in mode 'Scan To Network Folder.

  When I scan from the flat bed, I get a very narrow black line along the side of the analysis resulting very superior, but the background seems in good condition (although I have not tested this widely).

  These fine black lines occurred when scanning the HP 8500.

  I wonder if there is a setting to adjust it, or if it is a firmware difference between printers needs debugging.

  Hey KenAlker,
  
  There are a few things I want to check if you have lines when scanning using the 8600. I see that mention you that lines appear both through ADF and flat glass. There may be something both of the glass sections used by this printer, but more often that otherwise, this isn't the case.
  
  I would check if the printer is connected to a surge protector. If this is the case, then try plugging the 8600 in a direct outlet. Often the surge protector can cause this problem appears because the printer has a built.
  
  Also, try a hard reset:
  * Unplug the unit while the
  Disconnect the other end of the wall socket direct
  * Wait 30-60 seconds
  * Plug the unit to the top
  
  Also, try to take a look at the steps in the document found here.
  
  I hope this helps.

• OfficeJet Pro 8600: Officejet Pro 8600 leaves black lines on docs scanned when using the document feeder

  This is the second HP Officejet Pro 8600 I had - one was replaced by HP, after that the same issue arose.  I tried to clean the entire unit, but we still get a thin black line running vertically down the page.  This line is divided into sections of 1 "and 2.5" in length.  Sometimes I get the fine line and then almost a shadow line that is parallel.

  Any suggestions would be very appreciated I have scan documents to PDF format and it's hassle to put everyone on the flat for scanning.  I use the charger of the doc on a daily basis and wonder if this could have something to do with the lines.

  Thanks for any help.

  The question is a spec on thin (~ 1 "wide) glass to the left of the main bed scanner.  Clean this area as described in this document.  It can be difficult to see the affected area, a bright flashlight which is held at an angle to the glass can help find the place.  Even a very small spec on the glass can cause a black line when using the ADF.

  

• HP ENVY 5660: Solid black lines/blocks more data of a personal nature

  Printed documents have black lines solid or solid black boxes in the sections of the printed page.  They usually appear on boxes containing personal data (name, address, account #, etc.).  Usually occurs when printing statements of third-party websites.  Occurs when printing black and white only and when printing color.  Printer is calibrated and not other issues.

  Any thought oh what is causing this and how to fix?  Thank you.

  Change the browser alleviates the problem.  No problem with Internet Explorer.  Question using Google.  Thank you.

• Vertical black lines in middle of page

  Hi people,

  I have a LaserJet 4250n printer which has slight black spots / vertical lines in the middle of my pages. It is at the bottom, but it gets lighter in some points and again takes upward. I tried to replace the toner cartridge and cleaning of the rollers, nothing helps.

  Any ideas?

  Thank you!
  James

  Hi James,

  I am a technician in Australia HP printer and an employee full time. I deal with many printers with this one.

  Lines to the bottom of the page can be caused by a few things - according to what looks like the line.

  If it's a dirty dirty streaky brand constantly at the bottom of the page, migh you have a dirty oven - it may have been picking up toner and it has put in place and then put it down on paper.

  A thin black line set can be a scratched or developer - drum laser could be refraction and drawing the defect on the drum.

  Blank or white lines could be something stopping the toner to the study - under the toner transfer roller may have something stuck on this issue.

  A repeated mark or default could also be a dirty oven - glue or wax envelopes and labels could do.

  Try changing the toner with others to test - if you can borrow one.

  Make 3 or 4 cleaning pages - in the menu, configure device, menu printing, cleaning page to create/process quality.

  Remove fuser - door back comes, little blue clips, pull it. out - rotate using the green button and you might be able to gently remove something stuck in it.

  If you can get to an another 4250 / 4350 you could borrow from the fuser and know.

  For this machine, I find used ovens and dirty printers more often these symptoms.  Good next is of poor quality after market cartridges.

  Hopefully I can help you here

  Steve Hewitt

  HP Australia

  Melbourne.

• M3035: LaserJet M3035 Intermittent black lines on any Page, no question of Scanner Laser

  Currently of problems with two of these Multifunction products.

  Machine 1 # started a week ago and a half, intermittent lines that seem to be a problem of HVPS, (power supply high voltage).  Two lines on the page between the longitudinal edges, lines appear blurry.

  There are three printers M3035 in this room, machine #2 is mainly used for file scanning and until about 2 weeks ago was not used for printing.

  When #1 didn't #2 toner cartridge was traded in #1, (and #1 cartridge # 2), number one has always had the same problem so I ordered a HVPS.

  The next day, I was out and another Tech looked #1 and decided that it needed a transfer roller and also decided to Exchange #1 to #3, given that the person using #1 was printing which were to be made where they are not accessible to everyone.

  A few pages of test were performed on #3 and they looked good, so no. 3 has been moved into the Office next to #1.

  When #3 was turned on and tested, it was printed lines across the page!

  Since #3 is running on the power of the cable #1 cable has been replaced with a new cable.  The output has been verified for correct wiring, (tester used wiring available at Home Depot, etc.) and I took out my meter and the good test line and remained strong throughout testing printing.

  An extension has been completed past another outlet to verify that the problem was not gout and #3 failed again.

  #1 has been moved to the office #3 has and has been tested, he had problems, but they were slightly different, there was a grey shading across the entire page, because it was new I swapped the toner with #2 (this replace the original toner # 1) and #1 worked well, but was so #2.

  At this point, it was late on a Friday so that the print was made in another room and the problem put off until Monday.

  (will continue in another post)

  This printer has the same engine as the P3005 and there is a question that has been pretty common on this printer and it's the block of ground on the left side.  There is a mech that when you open the toner door separates a spring load piece since the acutal post that goes against the drum unit on this side of the Earth.  When you install the toner and close the door mechs two-piece flat against them and provide the grounding.  You will see I think that red ground wire that attaches from the bottom.  Most of the time the solution is very easy.  I just take a big piece of cardboard and paste it between the 2 black pieces of the MAN.  It remains in place because of the spring mech that keeps the two pieces together.  Once done, who takes care of the issue.  The lines that you get at least in my experience are caused by a lack of firm ground.  If you can recreate the lines still just have side trim left and just press the black mech and make a test and I do not know that the lines will be gone.  I repaired probably at least a couple of dozen of those printers who had this problem using the same procedure.  You can see the other two printers as it is a very common problem.  According to me, that the parties are called upon to lever earthing contact.  Chances are that supply high voltage was good.

• Why a black line does not appear when I turn it on, but goes off when I start a program

  When I turn on my machine, I get a vertical black line on my back drop. When I select a program the line disappears. Can you please help me with this problem. Thank you

  Hello Georgehebden,

  Thanks for your post.  Try to start computer in Safe Mode with network and download / install the latest video driver for your computer.  Please let us know the results so that we can better help you get this issue resolved.

  See you soon

• Photosmart C4450 scanner prints with a black line on the right side

  The need to issue to resolve, the RPG scanner with a completely black spot on one side of the page.  When used as a printer everything is OK

  Thank you

  Seth

  * Have you tried to clean the surface of the glass on the printer to ensure there are no particles causing this black line?

  * So, have you tried a hard reset of the printer?  Unplug the unit while on, disconnect the other end of the power cord of the direct plug, wait 30 seconds and plug in the.

  Try to plug in his own taken dedicated as well, because the electrical noise from other products can cause these lines in the analyses.  Also, check the steps in the document is located here.

  Let me know how it goes.

• Dell E1914h little black line problem

  Monitor Dell E1914h I have two problem has first the driver is not installed and showing the error shown in the picture, there are small black line on the right side of the screen, as shown in the last two photos below.  I have the solution to these problems as soon as possible?

  

  Hello

  Thanks for joining us.

  Let me answer your questions one by one

  1. the error message on the driver could be due to the compatibility of the OS, just checked the drivers available, there is no driver for Windows XP I see is the operating system you are running.

  You can close the popup and continue to use the PC as I do not expect the instructor to stop working without this driver.

  2. the downside seems to be a task or dead pixels. You can try this monitor on another PC or another monitor on this PC to confirm the problem is with the monitor.

  The fix for the problem 2 is to replace the monitor. Dell monitors to go with the standard warranty of 3 years. If during the warranty period, we can cover this issue.

  Thank you

• I am using captivate 8. The clarity of the published files are poor with black lines on the screen. Is there a way to fix this?

  Hello

  I use 8 Captivate. The clarity of the published files are very poor. It has black lines on the published file. Please suggest if there is a solution for this issue.

  Thank you

  Saida

  Hmm, Milot, why change the top instead of optimized to drag a quality which is the default setting in CP8? And why to substitute the quality of the blade in the preferences, if it is already set to high? I would like to know the reason, always eager to learn. I know that sometimes high leads to reduce the size of the file, but did not know that there has been better.

  My advice would have been to uncheck all the Compression settings in the preferences, size and quality. And I would like to know if the project has been recalibrated, if images have been resized.

• Problem with 'small black line at the right margin' with Folio Builder / Viewer to Adobe in the Ipad. ID CC.

  Hello

  When I create a Folio Builder and I check my project Id in the Adobe viewer (sometimes in the Ipad app and Desktop Viewer), I can see a black line at the right margin (maybe 4 px). And I can not set my background (it is an object with a color) to use the "full resolution available to the app in the ipad" and Yes, I'm using rules and I see that my object wallpaper is 1024 x 768. I tried several projects and upgraded the project for the "30" version

  But I am a new user with the ID/DPS. So, is this a bug reported? Or I'm doing sth wrong?

  And for me, the most important issue, will fix this when I send my project to the applestore and DPS transform my Folio to the store? Or what I see now that's what I'm going to see?

  Thank you!

  Sorry! I found an answer here in the discussion:

  http://forums.Adobe.com/message/5835960#5835960

  So the problem will be solved in the final application, and it's just the scrolling in the Viewer.

  Thank you!

• Using every night and compared to IE where I don't have a problem, there are black lines on all the pages of certain facilities of forum. Have screenshot.

  At first, I was told it was my video driver, but maybe it could be the motherboard. However, IE on the same pages of vBulletin does not horizontal black lines thin and thick, as shown in my screen shopt.

  Try disabling hardware acceleration in Firefox (you will need to close and restart Firefox).

  • Tools > Options > advanced > General > Browsing: "use hardware acceleration when available.
  • https://support.Mozilla.org/KB/troubleshooting+extensions+and+themes

• IPod nano 7 icon appears in iTunes, with Windows 8 or IP on both computers. Two nano 5s work perfectly. Short black lines appeared on the screen iPod

  NO icon of nano 7 will appear on iTunes despite trying 2 computers, Ip and win 8. Also tried two nano 5s and several cables and ports. Also, some black lines on the screen.

  What is "Intellectual property"?  Did you mean to type XP?  There is no iPod nano "5s". are these 5th gen iPod nanos?  Why do we say "iPod nano (6th generation)" in your profile in?  It's the iPod nano with the gen 7 problem?

  If the 7th gen iPod nano is new (model 2015), it does not work with a version of iTunes that runs on Windows XP.  It should work with the current latest version of iTunes on the computer of Windows 8, however.

• Vertical black line on Portege 3500

  My P3500 screen suddenly started showing a vertical black line with interference on the right hand third of the monitor. The line disappears after about 15 minutes, but still the interference. I plugged an external display that shows no display problem.

  Hello

  If the monitor external don t show any problem, to certainly show a malfunction. Try contacting the Service of your country partner. Explain exactly what is happening. I'm sure they will know immediately what the problem is.

• Incoming Fax page, left thick black line down the side edge

  Hello

  I recently bought a HP Photosmart 7520 printer and had to return because of a wrong switch ON / OFF the printer.  So I returned and bought another. This second printer works perfectly so far!  However, when I recieive a fax, the page has a very thick Black Line crosses the length (less than an inch from top and down) on the left edge. It almost seems to be a template for a fax page?  The first printer (a returned) did not do that, but it does not appear on the second printer.  In addition, the original page fax I sent to my friend and he said, that it doesn't have a thick black line on the fax page, he gets... and then he sent me along a return fax with this black line appears.

  Comment of thoughts,

  SyBerGuy

  Hello

  For more than a week since my last post. And I also had the printer connected to an outlet of power strip surge protector (never needed to connect directly to a wall, which I would have if I had a problem).  The problem has been resolved by replacing the large black ink cartridge, which was not printing text.

  In addition, earlier when I check the ink level, he showed the graphics still about 1/4 rest in the cartridge. I had also previously clicked on tell me when the ink level is low. None of this happened?  So now I have to watch closely what is printing a page of text clean/good.

  So for now, the printer is good to go and I hope not to have more problems... thank you for your help!

  Sy