M3035: LaserJet M3035 Intermittent black lines on any Page, no question of Scanner Laser

Currently of problems with two of these Multifunction products.

Machine 1 # started a week ago and a half, intermittent lines that seem to be a problem of HVPS, (power supply high voltage).  Two lines on the page between the longitudinal edges, lines appear blurry.

There are three printers M3035 in this room, machine #2 is mainly used for file scanning and until about 2 weeks ago was not used for printing.

When #1 didn't #2 toner cartridge was traded in #1, (and #1 cartridge # 2), number one has always had the same problem so I ordered a HVPS.

The next day, I was out and another Tech looked #1 and decided that it needed a transfer roller and also decided to Exchange #1 to #3, given that the person using #1 was printing which were to be made where they are not accessible to everyone.

A few pages of test were performed on #3 and they looked good, so no. 3 has been moved into the Office next to #1.

When #3 was turned on and tested, it was printed lines across the page!

Since #3 is running on the power of the cable #1 cable has been replaced with a new cable.  The output has been verified for correct wiring, (tester used wiring available at Home Depot, etc.) and I took out my meter and the good test line and remained strong throughout testing printing.

An extension has been completed past another outlet to verify that the problem was not gout and #3 failed again.

#1 has been moved to the office #3 has and has been tested, he had problems, but they were slightly different, there was a grey shading across the entire page, because it was new I swapped the toner with #2 (this replace the original toner # 1) and #1 worked well, but was so #2.

At this point, it was late on a Friday so that the print was made in another room and the problem put off until Monday.

(will continue in another post)

This printer has the same engine as the P3005 and there is a question that has been pretty common on this printer and it's the block of ground on the left side.  There is a mech that when you open the toner door separates a spring load piece since the acutal post that goes against the drum unit on this side of the Earth.  When you install the toner and close the door mechs two-piece flat against them and provide the grounding.  You will see I think that red ground wire that attaches from the bottom.  Most of the time the solution is very easy.  I just take a big piece of cardboard and paste it between the 2 black pieces of the MAN.  It remains in place because of the spring mech that keeps the two pieces together.  Once done, who takes care of the issue.  The lines that you get at least in my experience are caused by a lack of firm ground.  If you can recreate the lines still just have side trim left and just press the black mech and make a test and I do not know that the lines will be gone.  I repaired probably at least a couple of dozen of those printers who had this problem using the same procedure.  You can see the other two printers as it is a very common problem.  According to me, that the parties are called upon to lever earthing contact.  Chances are that supply high voltage was good.

Tags: HP Printers

Similar Questions

  • Black line through all pages HP Officejet 8500 A909a

    We've had this printer for some time at the office and not even a week ago, he started printing with a black line across all pages. Normally, that would be a problem with the head of the cleaner. FAKE! He is not the head of the cleaner. It will print the computer without the black line, and when something is printed glass monitor it won't be a black line in my documents. The only time where it appears is when I print copies of the Lac. It also occurs when we fax some of our documents to some of our major customers and businesses.

    We NEED this to work. What could be the problem? It must be well fixed as SOON AS POSSIBLE! It is urgent that I get a response on what I can do for this printer. Faxes should be sent each day of our office. I have just files accumulate on my desk. Help!

    Thank you!

    There is a small section (about 1 "wide) of glass which is used for the ADF to scan.  It's just to the left of the main window, see this post for more details.  A stain on the glass turns into a line, as the paper is fed through the document feeder.  This section of cleaning should solve the problem.

  • Horizontal lines on any page on color Laserjet 2500 l

    I was given this 2500l several years ago and he has had this problem since I got it - it prints dark lines of color on the entire page, in all four colors. The distance between the lines indicate a problem with the roll of T2 (it is the one that is built into the cartridges), but all four? And the strange thing is that I have printed a page, then open the printer and looked the roller, where I could see the extra toner that was originally the lines on the page. But when I marked the position of the line at the edge of the roll, and then printed another page, the line was to a different position on the roller, which indicates that the roll itself is fine.

    I tried to replace a couple of toner with brand new cartridges, but it has not changed a thing. Help!

    Thank you!

    I did a quick search and found the following link:

    http://www.feedroller.com/store/service%20Manual/color%20LaserJet%202500%20SM.PDF

    On page 226 is information on ordering parts and a list of the part and patterns.

  • Black lines across the page

    Each page that print includes a greyish black line.  How can I eliminate this line?

    Hi BlueEyedPea,

    Your printer would require an intervention... If you get the patches even a photocopy of his problem with the printer... You can try to clean the cartridge of the printer and see if it solves your problem else, you need to get in touch with your retailer of printer...

    Remove the cartridge and try clean and then align.

    Check out: http://support.dell.com/support/edocs/systems/prn942/en/om/942_om_en.pdf on how to align the cartridge.

    I hope this helps.

  • disorder of the copy or scan, just the shows up as vertical black lines on the page

    I have a HP Envy 120 printer all-in-one.  It prints very well.  But when I saw something to copy, it's just all black vertical lines.  No light in the scan bar.  I had HP replace my printer with a new printer and the same thing happens.  Anyone have any ideas?  I have a laptop with Windows 7.  Have used the printer for 5 or 6 months, but use only a few times a month, so did not notice a problem immediately the Copier.  Spent 4 hours on the phone with technical support who said first the version of the firmware to put up-to-date, but he was able to complete correctly.  He suggested that I had a surge in my wall connection, but that wouldn't make much sense given that I had just plugged the new printer to try and nothing else on this decision was having problems...

    Hi teropt. Reset of the printer and plug it directly into a wall outlet are a very important step to do if you do not have.

    This document covers troubleshooting for "Copies or Scans have vertical strips of black Pages or lines:
    http://support.HP.com/us-en/document/c03733649

  • HP Officejet Pro 8600: Vertical black line scanned single pages and copied

    The machine is about a year and treats a low volume (less than 100pgs/mth on average between pages sent from the computer, copying and scanning). Pages sent from the computer continue to print well, but for the last scan of the month or copy functions always produce pages with a thin (1 mm?) black vertical line in the middle of the page.

    Have cleaned the glass several times but no joy.

    Solution (s)?

    THX.

    Followed all the steps in case a link down to "shine a flashlight on the glass" and the flashlight revealed a tiny particle not detected previously, glued to the glass despite several cleanings. Once deleted, the line has disappeared. Thnaks for the end of the flashlight.

  • I have a HP Officejet Pro 8600 and when face I get a thin black line

    HP Officejet Pro puts a thin black line on my pages

    Hello

    You are able to print a self - test page, or print a document - you get the same black line when printing.

    You try to copy from the glass of the scanner or automatic document feeder?

    If the printout is fine without the black line and the problem only occurs when you copy - follow the steps mentioned in the document.

    http://support.HP.com/us-en/document/c02881567

    Although I am an employee of HP, I speak for myself and not for HP.
    Click on the star of CONGRATULATIONS on the left to say 'thank you '.
    Please check one response to "ACCEPTED solution" if it has solved your problem, while others may find it.

  • black lines

    When I make a copy or try to scan on my all in one printer I get vertical black lines on the page.  It only if I have something to print from the computer.

    What type of operating system you have on your computer? (Windows 7, XP, Vista, etc.).

    Here is a link that can help too.

    http://support.HP.com/us-en/document/c01887471

  • Black line on prints/scans using HP8620 ADF

    A thin black line down the page appears on the documents copied or scanned with the ADF on my 8620. Copy/scan from the flat bed is very good. All the ideas of cause and cure?

    This is probably a small spec on the thin glass to the left of the bed main scanner.  Specification can be difficult to see, it can be useful to hold a flashlight light parallel to the bed to hilight the spec.  The document here can help solve the problem.

  • OfficeJet 6500 all-in-one - black line down page

    Our newly purchased Officejet 6500 all-in-One is the production pages with thin black lines down the page about 2/3 of the way through the page (right side of page).  Is there a solution to this problem?

    This was only happening with ADF.  After several cleanings with no changes, I found this forum.   After reading the plug on the glass, I went back and really clean the glass.  This has allowed the problem.  Thanks for the forum.

  • Cannot use the button Delete, build, forward, or any box above. There is a black line through each box.

    There is a black line through deleting it, the answer, the next high school & page E-mail t button. It I cannot select any option. E-mail works fine in Internet Explorer. Please help find my e-mail options.

    It seems that the same problem has happened once with Gmail. The proposed solution can be seen here, although he did not have all the answers: override system colors

  • Why does my HP laserjet 1022 produced a black line on the right side of the page?

    Why does my HP laserjet 1022 produced a black line on the right side of the page? This occurs by using Word 2003, Photoshop, Acrobat etc. I don't get this with my Epson printer. My printer drivers are all to date. OS = Windows 7.

    Hello dqmcg

    Have you checked programs and OS - seemed to be OK, so did a new install of the printer. I have seems to now work OK - IE the files previously printed with lines now don't (only verified although some).

    I think that I was naïve in beliving Windows when he says that the printer and the driver were OK, and when I did a re-driver installation, Windows just used the file I already had. Also the "print test page" printer properties was always OK. Must have been very slight damage to the driver who showed up only with certain types of files of a few (different) programs.

    Thank you very much for getting my brain to work and begin to think logically.

  • LaserJet M451dw: black line to the bottom of the page

    When I print a document, a continuous black line appears in the middle of the pages. The first 2 pages are normally well, but the rest of the pages have the black line.  I cleaned the printheads etc.  I hesitate to change the ink because there is more than half a cartridge left in all colors.

    It sounds like a faulty black toner cartridge.

    After printing open access toner and remove the cartridge and look at the drum and if there is a black line on the drum, then it would prove.

    If you have half left toner cartridge is still in warranty and you may be able to get it replaced.

  • Thick vertical black line on the entire length of the page

    I have a HP LaserJet M1530 MFP Series PCL 6.  When I print normally there is no mistake in the image, but when I make a copy I have a thick vertical black line on the entire length of the page. The black line is about 2 inches from the left edge of the page. The problem is older than the current drum cartridge which was just replaced a couple of months. Never, the problem occurs with a normal printing, copy only and occurs with every copy without exception. Does anyone have any ideas/suggestions?

    Hello somedudeand welcome to the Forums of HP.

    I'm sorry, but to get your question more exposure I suggest posting in the trade forums since it is a commercial product. You can do so at http://h30499.www3.hp.com/hpeb/ .

    I hope this helps!

  • Vertical black lines in middle of page

    Hi people,

    I have a LaserJet 4250n printer which has slight black spots / vertical lines in the middle of my pages. It is at the bottom, but it gets lighter in some points and again takes upward. I tried to replace the toner cartridge and cleaning of the rollers, nothing helps.

    Any ideas?

    Thank you!
    James

    Hi James,

    I am a technician in Australia HP printer and an employee full time. I deal with many printers with this one.

    Lines to the bottom of the page can be caused by a few things - according to what looks like the line.

    If it's a dirty dirty streaky brand constantly at the bottom of the page, migh you have a dirty oven - it may have been picking up toner and it has put in place and then put it down on paper.

    A thin black line set can be a scratched or developer - drum laser could be refraction and drawing the defect on the drum.

    Blank or white lines could be something stopping the toner to the study - under the toner transfer roller may have something stuck on this issue.

    A repeated mark or default could also be a dirty oven - glue or wax envelopes and labels could do.

    Try changing the toner with others to test - if you can borrow one.

    Make 3 or 4 cleaning pages - in the menu, configure device, menu printing, cleaning page to create/process quality.

    Remove fuser - door back comes, little blue clips, pull it. out - rotate using the green button and you might be able to gently remove something stuck in it.

    If you can get to an another 4250 / 4350 you could borrow from the fuser and know.

    For this machine, I find used ovens and dirty printers more often these symptoms.  Good next is of poor quality after market cartridges.

    Hopefully I can help you here

    Steve Hewitt

    HP Australia

    Melbourne.

Maybe you are looking for

  • How can I add the history tab in the sidebar

    I would like to add my history tab in the sidebar.  Any suggestions?

  • Satellite C855-1GQ - missing webcam

    Cannot open my webcam with Skype or anything like that.It is not in the start menu and when I search for it, it is not found. I looked in the Device Manager, and he's not here. It says webcam not found. I have Satellite C855-1GQ.Help, please

  • How to replace a hard drive in 1625CDT?

    I need to replace the hard drive in a 1625CDT. I have a disc, but can not find a way to get the case open. I also can't find the documents of support with instructions how to proceed. Anyone can provide guidance for this? Please don't tell me to take

  • How the string output to a common indicator?

    Hello I have a sequence of battery with 10 picture sets, there is a wait to delay of 2 seconds between each image. I have a common indicator of channel set and I want to output a string to this indicator in the first framework before the codes betwee

  • HP Pavilion 15-N220TX

    It's a beautiful machine but am wondweing if I coud change hard drive solid-state Archie