Jabber / presence Setup

Similar Questions

• VCSE Jabber presence does not

  Hello

  I have some problems with the presence, through the VCSE for a jabber client registered to one subarea other than failing the VCSE subzone.  In addition the environment uses AD for authentication of the client so the VCSE has the default area, sub-area by default and traversal area set to "do not check references" for auth policy.  When the customer registers to the subarea of default, presence works properly.  When I create a subzone to isolate a specific group of jabber clients, register of customers using their credentials of the AD (checked this incorrect password causes failures) but I get an error 403 policy updates to presence.  I need to create this subarea, so I can use a search rule that matches the subfield as source and then replaces the alias with a non routable target so this client group can only receive calls.  I tried to use the local list of CPL to do this, but once again because the VCSE does not all identifications CPL rules do not apply.  If it is a bug in X7.2?

  Jarrod Hey,.

  You can do so by implementing the following:

  The information below should help you get Jabber to authenticate correctly on the highway even if you push the control. Jabber must authenticate properly for the presence at work. After this is implemented your search rule should work as you wish as well as the presence and authentication.

  In a secure design, the VCS (control and Highway) would require identification for registration information. Here is a drawing that is not described in the guides of the admin, but has been used successfully.

  The Control of VCS would have Active Directory Service active and joins the Active Directory domain. For VCS authenticate the credentials of Movi/Jabber on Active Directory before the SUBSCRIPTION for the supply is sent to the service of commissioning, the default Zone would be set to verify the credentials. For requests for SUBSCRIPTION from the highway, the area on the VCS control would also to verify the credentials. It handles authentication for the provision.

  The next part is the record of the Movi/Jabber client. The subzone to which the customer will register must also be set to verify the credentials. Here's everything you need for internal records (registration to the VCS control).

  For the Highway, things get a little more complicated. For commissioning subscription, the SUBSCRIPTION is forwarded to the VCS control. With the area on the VCS game to check the credentials, you're all set. Now on registration to the highway. The subzone to which the customer will register to must be defined to check credentials. From the motorway VCS don't have direct access to Active Directory, we use local credentials on the highway. A set of credentials should be configured in VCS Configuration > authentication > devices > local database. You will create a single name and password all Movi/Jabber clients will use. The end user has NO need to know these credentials. The username and password is provided to the Movi/Jabber client via configuration data it has received. To set up these data, MSDS, you must configure a SIP of authentication user name and password for SIP authentication in the configuration of the commissioning. For these options to be available, you must ensure that you have downloaded the configuration template xml for the Movi/Jabber version you are using. The xml file is included in the zip package full of the client which can be downloaded on www.cisco.com. So, who will be recording from the highway. Now, this creates an interesting situation with VCS control. The internal Movi/Jabber client will receive the same provisioning configuration and will attempt to use those same credentials when you register for the control of VCS. The VCS control is already set to authenticate against Active Directory and Active Directory ONLY registration.

  You will need to create an account in Active Directory corresponding to these credentials. The Active Directory account didn't need special access. It is used only for authentication purposes. A few things to keep in mind: SIP authentication user name and password for SIP authentication are stored in clear text configuration configuration. This means that the data is sent in clear text. To be sure that these data are not compromised on the wire, do not forget that you are using for your communication SIP Movi/Jabber TLS.

  Thank you, Adam

• Problem of points of termination/Jabber presence

  Hello

  We encountered a problem on the publication of presence of endpoints and jabber via Highway VCS.

  These points of termination/jabber who are registered on the SCV - C do not publish "online" status, or a green icon on the phone book of the jabber, which is recorded on the VCS-E.

  Also the two jabber users registered on VCS - E even publishes state of evil presence. It displays 'offline' even that they are on VCS and connection status is set on the jabber client.

  No questions on the points of termination/jabber only recorded on VCS - C.

  Jabber client registered on the VCS-E may appeal to the point of termination/jabber registered on the VCS - C and vice versa.

  The VCS configuration - C and presence of VCS - E:

  User agent SIP Simple presence: 'ON '.

  By default the State published the saved settings: 'online '.

  Server SIP of SIMPLE presence: 'On '.

  User agent of presence and the State of the presence on the two VCS server are active.

  Thank you very much for the help.

  BR,

  Acevirgil

  Hello

  You must have the presence server enabled on VCS - C. The AUP should be enabled on VCS - C and VCS-E.

  Using FindMe?

  / Magnus

• Is it possible to publish for Jabber presence information in the tourist complex?

  Hello

  We run TMS 14.2.1, TMSPE v1, VCS x7.1

  We organize several controls of VCS for several organizations, including the couple with potentially different motorways VCS. While the appeal of one domain to another is very well, adding that the contact for the alien to you field Jabber list does not have the ability to view their presence information, as it does when you add a contact to your own domain name. Is this possible?

  Chris

  What are the parameters of your presence on the highway VCS? You must enable the user agent of presence and clear the presence server, so applications of presence will be sent and nothandled by the highway.

• Jabber presence doesn't work not between VCSe and Express, but works if you are registered to the same VCS...

  Hello

  I have a problem where the presence does not work between users registered on the VCSC and the VCSe.

  If a user on the VCSe registers, they cannot see the presence of VCSe registered users, and even, registered on the VCSC users see only the presence of records on the VCSC.

  TMS is running 14.1.1 with TMSPE

  VCSC and VCSe run every two X7.2.

  Both the VCSC and and VCSe each with authentication Active Directory (direct)

  Wouldn't be better to have control of VCS and VCS Expressway with authentication Active Directory (directly) on the control of VCS?

  Thank you very much

  Rob

  Hello

  in most cases, you want the VCS control to contain the presence information and VCS Highway to simply forward requests for control of VCS.
  Should be set to the 'on' presence User Agent and server on your control and only the User Agent of the presence on the highway in position 'on '.

  You can find more details in the VCS Administrator's guide.

  Sent by Cisco Support technique iPhone App

• Jabber - groups of presence

   

  Is it possible to separate the Jabber presence so that managers can see the presence of managers and staff, but staff cannot see the presence of managers or engage in chat, etc.?

  I tried to work with groups of presence, but nothing helped.

  Hello

  I don't see such an option in jabber, the only option available is the option 'Privacy' that allows the user to decide who can interact with this user. Please see the following link

  http://www.Cisco.com/c/en/us/TD/docs/voice_ip_comm/Jabber/Windows/9/JABW...

  HTH

  Manish

• Unable to connect to presence server Jabber clients

  Salvation;

  I am a newbie in Collaboration and to learn basics who set up a small laboratory including 11 CUCM, presence 11 and two phones 7821 Cisco. I have configured CUCM and presence and set up a SIP trunk between them according to the documents. I tried to configure the client Jabber on Windows, but in vain. first of all, I created some local users on CUCM and have some LDAP users that have been synchronized with a test AD in which both the presence and the CUCM are members of this domain. I set up a local users CUCM for Jabber Client and to configure as follows to configure the Jabber Clients according to the documents.

  My first question is the format of the user name that should be used with Jabber. client Jabber said we use "[email protected] / * /" format, but I saw the videos on the Internet using normal user name and password. regarding the fact that I have configured a local user for the Jabber CUCM, I entered in the form of "username" but Jabber said the format should be as "[email protected] / * /'." "

  the second problem is that even after writing the user name in this format, the Jabber said that 'not to communicate with the server'. I can ping the CUCM and presence server both by using their ip addresses and hostnames through my PC on which is installed the Jabber. also I wrote serves him the IP address on the Jabber client while trying to connect the Jabber instead of their host names. is there any requirement to be member of a single domain?

  I tried Jabber for iPad to connect to the presence, but in vain too. y at - it knows no question or tips about the present? Otherwise, I can explain the steps I went through them to set up the presence and the CUCM for Jabber clients.

  best regards;

  Because for the most part, allows you to know the details of connection SRVs and SRVs work based on the field.

  You have successfully configured your SRVs according to configuration guides?

  It is very likely that some missing config or a misconfiguration.

  I have videos on how to configure the IM & P as well as Jabber config integration

  https://www.YouTube.com/playlist?list=PLFuOESqSTxEvZChqWgAJanctohRMe99CR

• Authenticate the accounts of Movi (Jabber) with LDAP/AD

  Condition: I have a setup of TMS-control-Expressway (VCS are x7.0.2, TMS is at 13.1.2).) Commissioning is good in all areas (manually created Movi accounts are correctly identifying you and calling functions are good). In the start-up directory, I have the root directory. In the root directory, I have 6 Movi accounts created manually as well as 6 subdirectories. I installed each subdirectory with a Base DN and DN (each subdirectory has a different Relative DN).

  Result: Each subdirectory is to import users AD it was supposed - and all areas that fall under each user Movi is populate correctly (email, title etc etc). The only area that is not filling (and should be grayed out/disabled) is the password field. This field has a default password for each user. In addition, the password field - meaning that it can be changed right there in the provisioning of TMS directory. The search AD to autheticate password is obviously not the case. FYI, if the Movi user uses their username (domainsername) AD and the password entered manually, Movi makes login.

  Attempt of high school: I also went in the control VCS vcs configuration > authentication > devices > Search AD and filled in the fields (to add the VCS control to the field). I also made sure authetication on VCS is set to 'local database', but the "auto" value on the challenges of the NTLM protocol.

  It doesn't change anything. MOVI users opening a session cannot use his AD password.

  Timothy,

  Yes, it should work. I see no problem with keeping the subfield of "treat as authenticated.  Again the subzone is where any request for 'registration' will pass through including your presence and your phonebook.

  the initial Setup subscribe for MOVI/Jabber is still going through the default zone which, in your case, will be challenged for credentials.

  Try it out and if face you any problem then post here.

  Thank you

  Alok

• EliteDesk 800 800 TWR G1: > > > media presence check then no option to boot from

  Hello Sir

  I buy a HP EliteDesk 800 G1 TWR Telechareger pc. By default, Windows loded 8.1.I want to load windows 7 x 86 in this pc, so I inserct win 7 disc then reboot & system is restsrted ite system start-up

  > Media presence check then no option to start

  Please solve my problem

  Prabhu Prasad

  [Personal information]

  Immediately after turning the power on, press the ESC key. In the menu that opens, tap F9 Boot options.

  BTW you need to maybe get into the BIOS setup and disable Secure Boot to allow booting from the CD/DVD.

• Move the CUPS 8.6 to GI & P 11.0 - client for Windows 10.6 Jabber

  Hi community support

  We are modernizing our environment voice of 8.6 to 11.0 CUCM, CUPS, CUC and UCCX including passage of MCS including Cisco UCS servers. Regarding CUCM, UCCX, and CUC I just finished these several times in the past and we have a detailed plan. Regarding the CUPS/Jabber, we always try to finalize the design of upgrade and after reading many documents and a few good videos by Jaime Valencia our particular upgrade scenario is still uncertain.

  We were using Microsoft OCS and decided to migrate to CUPS/Jabber so we have 3 groups CUCM we created 3 only the CUPS server clusters (Let's put HA when we go to Cisco UCS, but at the time we had only 3 MCS spare servers) and they have peers inter-classes.

  • We use a single domain across all 3 groups.
  • 100% of our users use IM & P through integration of voicemail and calendar and call control
  • 10% of our users have also softphones
  • We do not use SRV yet for service discovery due to having 3 groups on 8.6 so we Jabber for Windows 10.6 bundled with Microsoft SCCM, specifying the Type of account as Cisco IM & presence and login server 'use the following server' that points to the Publisher of CUPS.
  • First time users will have to specify [email protected] / * / how he discovered the area, use only the user name and password to connect, after which its caching and all connections are automatic.

  My questions are:

  • When we improve CUPS 8.6 to IM & P 11.0 ourJabber for the client configuration Windows 10.6 will continue to work without modification?
  • We currently link to the Type of account 'Cisco instant messaging and presence', this allows us to use IM & P and the voice that is to control the calls and softphones, you would select Account Type Cisco Unified Communications Manager in what scenario?
  • We want to use SRV for the Discovery Service, but as we have 3 groups who are upgraded in an approach by steps are better wait we have updated all 3 groups, we can use a single SRV for multi clusters with ILS?
  • When you first connect to Jabber, you must enter [email protected] / * / while he discovered the field then we just enter username and password (less the field), the average of SRV service discovery simply enter the user name and password once without the specified domain?
  • This SRV for the discovery service also provides the AP for connection if the main server is down or is making another way?

  Thank you, Carl Ratcliffe

  Preston, Lancashire England

  Yes, the configuration remains the same

  As for the second question, read here:

  http://www.Cisco.com/c/en/us/TD/docs/voice_ip_comm/Jabber/10_6/planning-...

  http://www.Cisco.com/c/en/us/TD/docs/voice_ip_comm/Jabber/10_6/CJAB_BK_C...

  As now CUCM is one that handles services profiles, which define everything, you want to use _cisco-uds

  #3 Yes, you probably want to wait to get them all in the same release, then make sure THEY works very well, and then configure the SRVs

  #4 Yes, the first time, it will ask for [email protected] / * /, once he finds the SRVs it caches the user and you need only the password.

  #5 Yes, you can configure the SRVs for all servers in the cluster.

• Windows Jabber client

  I strive to Jabber Windows installation client.

  I CUCM 9.1.2 and joined my announcement in CUCM. I installed Windows Jabber 11.1.1 and can login with my account AD information.

  But now that I get. I have a red bottom left of Jabber. I searched help and he says:

  Connection error. Ensure the server information in the PhoneServices tab on the Options window is correct. Contact yoursystem administrator for assistance.

  However, I looked and there isn't a telephone Services tab in the Options window. So I looked further and found a document saying configure the instant messaging and presence. But then I found another document saying that IM and presence has been fully integrated in CUCM 9 and later. I don't have a presence server right now and don't even know if I need one or not. Until the tinykitty am supposed to do? Completely lost in ass of Cisco. I well it might be interesting giving Jabber to everyone but is just a confusion and frustration and more I work with Cisco more, I hate it.

  You posted in the wrong forum, this forum was for the 'free' JabberVideo service that was received by Cisco, no Jabber.

  Suggestions you move this to the Jabber Client forum where you have a better chance of getting a response.

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• Cisco Jabber CDR analysis and reporting: the lost packets and other info call stating "Null."

  Hello

  I have recently setup Cisco Jabber Setup and make a video call between Mac and Windows laptop. When I go to the CDR reporting, I can find my call details when I search after the end of the call. However, I see lost packets, jitter, latency as Null.

  I looked in the support forums and made all the required configurations such as going to service settings and allowing the call diagnosis. I also uncheck CDR load only one box, but not seeing any information other than the ip address and the details of the bandwidth of VideoCAP.

  Am I missing something?

  CDR.png

  

  No, the CMR is not implemented in any current version of Jabber, the next version of Jabber will be the first to have * some * RMC capacity.

  What you see at the present time, is the expected behavior.

• Configure Jabber for Mac with local CUCM and WebEx Connect

  Hi, I was wondering if someone could set up the Jabber client Mac 8.6.2 to use the server of presence of WebEx Connect with a local farm the CUCM and connection of the unit. The tab preferences accounts show or allow the addition of voice services. I added work CUCM preferences plist file local, which, according to me, are the correct entries, however I still can't see the accounts under the Preferences tab. We currently do not have a presence server local cisco where the obligation of trial WebEx Connect Server because I can't get past the first step of configuration without it.

  concerning

  Paul

  You must connect to your Webex portal and activate these settings to connect.  Once they are allowed, log out/log in Connect and you should be able to configure CUCM TFTP, etc..

• Cisco Jabber for Windows - Added new friend

  Hello

  When I try to add a buddy to our internal directory, it does not work. For a short time the new boyfriend is in the buddies and then rinse... never again. In the presence of CUP Viewer, you don't see also no boyfriend.

  When open UPC 8.5.x then, it works perfectly. If the two (Jabber and UPC) has started, add new buddy in! Jabber! and in the UPC he is there. Jabber is not not do anything this boyfriend.

  If now! The new boyfriend UPC or Jabber logs by himself... it would have shown in the buddies of the Jabber Client at all times. But the other guy must be connected by itself.

  (1) file-> new-> contact

  (2) looking for someone

  (3) define the Group

  (4) add

  External friends... added to the list works and they stay there.

  Here the break error report.

  thx for all the help phil

  One of your user names contain a space by chance?  Because I see a similar behavior and I followed it down to user names (and therefore IM addresses) that contain spaces fundamentally break totally Cisco Jabber, but CUPC 8.5.5 works very well with them.

• Cisco Jabber 10.5 for Windows boot process

  Hi guys,.

  I had following problem and impossible to find a clue that can move me somewhere.

  A customer has a jabber Cisco 10.5 deployed and integrated with Active Directory.

  Every day, customers are initializing requests of sends customers jabber with phone numbers against the AD domain controller (these figures are not the contactlists - personal or company) and as there is that much more of this question in a moment the utillization of the announcement is almost 100%, which also makes the problem with the connection in outlook (is also integrated with the Cisco Jabber for windows)

  I searched the Web for tips but have not found anything.

  My questions are:

  The data for Outlook Personal AddressBook starting the Jabber questioned via Jabber Localy or domain controller?

  What is the process of starting the Jabber for Windows on the integration of directories?

  Is this a normal behavior of jabber?

  #####################################################################

  Here is the configuration of the config.xml file - jabber (passswords and areas are changed):

   
        BDI
          AD
          AD-IP address

  Field of presence
             389
              DC = presence, DC = domain
         Username
          Password
          Fake
          True

  ###########################################################

  Hello

  Jabber will not interview contact Outlook address book DC until a manual search is made.

  Also default contact jabber, the domain controller for the windows PC host.

  Each time that you enter at least 3 characters (default for search), jabber first find cached contacts, then outlook address book and then search the directory.

  The attached config file is BDI type ie. for MAC computers, it will not take effect in windows PC.