Jam (good)

Similar Questions

• OfficeJet 7500 E910 model: 0x61011bed error code

  0x6011bed error code is displayed once the printer performs an impression and to enable again the printer requires a lot of button pushes on the display of messages of 'OK '.

  I have turned off the Officejet 7500, disconnected from the power, waited a minute, deleted and reinstalled ink tanks and the print head, sucked and bluff visible dust but still cannot make the mistake go away for very long, with usually error code return after printing (print or receipt of a fax).

  I perform the extra step or need of cleanup for more than just a job printing after the error code clears?

  An additional observation: If the print job is multiple pages, once started the Officejet 7500 completes the task, but is to begin after the error code displayed is the problem.

  Hey @pauledinger,

  Thanks for getting back to me on this subject.

  Because you also get a paper jam error, you can click here to access the paper jam good troubleshooting steps. Once the support document opens just review the Solutions proposed to ensure that no paper or debris is hidden in paper path in your product. Support document also guides you through the rollers for the cleaning of the printer. Regarding a paper sensor, you can not clean the sensor itself. In addition, if the sensor is defective, it is a non-replaceable part on this model of consumption of the product. Therefore, a replacement of the entire unit would be necessary.

  After the jam troubleshooting steps, please try printing. If the error persists, can please click you here to send last programming Firmware update to your printer. The Firmware is the "brain" of your printer and control that made your printer and how your printer it. If there is a corruption in the internal programming in your printer, it can cause performance problems. Your printer must be in a State of 'ready' to 'send' to update the Firmware of the product. If your printer indicates a status of error on the Panel until the firmware update will most likely fail. Once the firmware update completed test print to see if the problem has been resolved.

  If the error state persists after checking for jams and completing the update of the Firmware a replacement of the entire unit would be the next step.

  Please let me know if the troubleshooting steps I've provided resolve this error state. Good luck!

• I want to use my camcorder panasonic SC-with v720 good hdmi as a webcam how do I do that

  Subject: I want to use my camcorder panasonic SC-with v720 good hdmi as a webcam how do I do that

  I was looking for a good webcam (video camera) that I can use to spread my webinars.

  I can't find on the website of apple that works well with my macbook so I can use it in quicktime, Skype, facetime, google den, jam Webinar, goto webinar etc.

  If you know that a good webcam please let me know.

  Then I found an article on the internet how to use your own video camera as a webcam.

  But you must have some sort of converter video thunderbolt Blackmagic Design UltraStudio datalogger of 150 dollars.

  I don't understand that, my camcorder has my mac book has hdmi hdmi why isn't is possible to connect them so that I can use my camcorder as a webcam.

  My panasonic SC-720v is also compatible with imovie.

  Please who can help out me.

  Greetings

  Conrad

  The Netherlands.

  By the present the link which connect a video camera with the crush blabla UltraStudio recorder of Blackmagic Design Mini converter

  https://Ozar.me/2014/03/using-HD-camcorder-Mac-webcam/

  I think that the HDMI on your Air port was released only to screen external which is why you need the converter.

• B210 in paper jam printer there is no paper stuck in the printer, but the screen shows paper jam

  Paper jammed paper but screen says paper jam jam preformed the resolution of problems and no resilt

  Hello

  Have you tried the steps outlined in this article. Give them a shot and tell us if it helps.

  Good luck!

• OfficeJet 6600: Paper jam resulted in ink system failure

  Paper jam resulted in the failure of the inkjet system. Error 0 x 61000016 is reported.

  I tried troubleshooting basic procedures, but the track of the cartridge seems to be poorly aligned, that is, when I opened the door, only the black cartridge is available. This is definitely not normal.

  The above error messages persist after stopping and restarting. Replace cartridges results in the same error.

  The jam massive caused many, many problems. I had to fish out bits and bits of paper of all nooks and crannies.

  Too boot, when it was all cleared up I had to cold start the printer, remove and reinstall all the cartridges (because the printer is no longer recognized an any of them) and go through a three step routine cleaning print head.

  Very messy.

  But the good news is that everything is all right work

  My next gripe is about the ongong with cartridges properly filled with Staples, Costco, and al that so-called re - define the chip in the cartridges.

  That never works.

  The result is that the printer does not recognize an original HP cartridge when it is filled again and then starts the everlong question when a cartridge is empty actually.

  Of course, I know when a cartridge is empty, it weighs about 19 grams.

  But we should not do that math.

  I understand that HP would love everyone to buy their cartridges, but they cost way too new.

  Seems average spririted. I could be wrong, but we are all in this together.

  The ink is ink. I think HP should be a little more forgiving for us "little guys" who need to pinch pennies.

  Just saying '

  Rainman

  P.S.: And Yes, I agree the continuous message on 'counterfeit cartridges' when I plug a Costco filled HP cartridge. They are not counterfeit, they are actual filled HP cartridges of actual real RGB ink! And, of course, I accept the responsibility addressed by the messages of ad nauseam when I insert these original re-filled HP cartridges. They seem to work well. Perhaps there could be a happy medium where HP could give a little and the moniter ink levels. Of course, I can continue to weigh the cartridges when the print head cleaning routine fails to get good results. But again, HP should be a little more friendly and less motivated in this respect of profit.

  But having said that, the disorder shoot works great, and I appreciate it!

• HP officejet 8500: jam on fax error message

  My printer gives me a paper jam error message everytime I try to fax on the set of the car. But he fine Fax out of the glass. Also, it prints multiple copies of auto tray.   Amy ssuggestions before buying a new machine.  It is 5 years old.

  Hi @Horseshoer,

  Welcome to the Forums of HP Support!

  I see that you are not able to communicate by fax using the ADF on your HP Officejet 8500 printer. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  I understand that you are able to fax using the scanner, which is nice to hear. I also see that you mentioned that you are able to copy of the set 'auto '. Are you referring to the ADF (automatic document feeder) or the feeder?

  If you are able to copy multiple pages using the ADF, fax should also work. The printer may have a little problem, that can solve a reset.

  I would like to do a hard reset to see if that will solve the problem.
  Let the printer and disconnect the printer cable and the wall socket for 60 seconds.
  Reconnect the power cable to the output of the printer and the wall, and not a surge protector.
  This ensures that the printer is full on and can help this situation.

  • Make sure that the printer is connected directly to a wall outlet. (do not use a hub or a surge protector) This ensures that the printer is full on and can help this situation.

  If you have a computer that is running Windows 7 or an earlier version, I would update to the firmware of the printer. Clickherefor the download page.

  If you are unable to update the firmware of the printer, I suggest to try partial reset or Semi - full Reset. I can send you this information in a private message. In the forum next to your handle name simply click on the envelope to see.

  Please reply to this message with the result of your troubleshooting. I can't wait to hear strings attached good luck!

• Do not print error 13 paper jam, no paper jam

  I have a printer HP laserjet 4 plus. First turn on the computer and get to the stage of loan. Print and receives information. Printer starts and form feed light turns on and says 13 paper jam. Help, please.

  Most likely, the roller is worn out.  I guess you are trying to print from the cassette tray and not the fold down manual tray.  If so, remove all paper from the cassette tray and place on 10 sheets on the manual fold down from the shelf to the front.  Try and print again and see if it picks up the paper.  If it feeds OK, chances are the drive for the cassette tray roller is worn and should be replaced.  You can try to clean the rollers with warm soapy water and dry, and it can be good to use while you wait for a replacement roller.

• G41 - update to Vista Edition family Basic is a good idea?

  sorta, I like to keep my g41 and was curious if an upgrade to Vista Home Basic is a smart idea. as you know, my hardware is a little outta date... Thanks in advance

  James

  Note of the moderator; subject published

  Fortunately, NVIDIA keeps supporting the legacy cards. If most of the distributions out there should work fine.

  If you're new to Linux, I would try Linux Mint on a CD or USB drive. Lubuntu is also a good idea because he goes easy on older hardware. You can continue to try different distros until you are comfortable with one or find one that you like best.

• In windows 7 my all-in-one Officejet HP6110 constantly gives paper jam paper on first impression.

  After an order of printing the first sheet of paper is taken in two stages, the first step determined fast followed by a slow forward paper at the end of which the flashing light red starts flashing and the screen Announces "clear paper jam and press ENTER. Later print a product normally. This behavior all constantly repeats on each new print command. On my Windows XP pc, the printer behaves without problem. I think it's to do with the operating system. Any ideas how to correct this anomaly will be welcomed.

  Hello
  
  This article should cover the problem you are experiencing. Give the steps described a shot and tell us if it helps.
  
  Good luck!

• Cartridge HP 1350 Jam/Incompatible transport

  Hello... I have a HP PSC 1350, old but works always, but the end of problems with persistent transport jam and cartridge compatibility. Basically, the symptoms are the following: after hitting 'print' transport sets on the left side. Not really of interference, but to rest it. If I open the default gateway is in the middle position to remove a cartridge and replace.

  I have two new cartridges in the printer. The black HP56 arises from HP, the color HP57 is a generic. I used generics for years without any problem.

  Anyway, the message I get on the screen is "check printer cartridge" and in the application of series HP PSC 1300, the error message is "the black ink cartridge is faulaty or incompatible with this printer." I replaced the cartridge several times and every time I do the printer will start, print a test page and do some printing tasks. But half an hour later when I hit print, it will return to the same set of problems. Weird that it works very well but not half an hour later. Sometimes if I do several resets I can make it work but after a rental it sitting idle going a bit, no.

  So, essentially, the printer works fine when you're printing so I think it's a software/driver problem. Not sure if it's related but I noticed that the problems began after I upgraded to the Mavericks 10.9.2.

  Clues?

  Mike

  Hi Mike (Coopershawk).

  Sorry to hear that these steps did not work!

  I don't have access to service manuals (if they are still there) that I could link you too, but you can try to use Google and YouTube to see what you can find to disassemble the printer. You're right, if you can't fix it, it will be recycled anyway, why not just not?

  I hope that you are able to fix this on your own Mike here and I thank you for your time! Good luck and feel free to let me know how you go with the repairs!

• Photo constantly order of photos in a slideshow changes no matter how many times the movements of the user the photo back to the good look at an order. Example: Bathroom Plans eventually grouped with pictures of kitchen! I have found no way to stop this o

  Apple Photo 1.3 serious problems - how can I SOLVE all these problems?

  (1) breaks down without rhyme or reason no matter where I am in the workflow.

  (2) pictures will not be Shut Down Every Time, even after several days of waiting.

  (3) aPhoto frequently badly chooses picture in the EDIT picture option, I get a picture different than the one I clicked on which is on a 100 pictures in a row.

  (4) picture constantly order of photos in a slideshow changes no matter how many times the movements of the end user the photo back to the good look at an order. Example: Bathroom Plans eventually grouped with pictures of kitchen! I have found no way to stop this weird behavior! Is there a way to stop this? If I drag the photo again some 7 additional photos in the slide show, after a minute or less, he appears again to where it was it not. !@#$%$#

  (5) If you make any CHANGES to a photo, it often changes the appearance of your complete slideshow of this picture with impatience. So you lose all this not work fix your configuration of the slide show. Even changing the order of photos once more that I had put back where they should be. !@#$$#@

  (6) photo identifies often shades of lamps and long door handles as the faces of the people.

  (7) photo made bad decisions when it comes to brightness, contrast and colors effortlessly around other than to use other software, where as with iPhoto there was a lot of workarounds. I could continue, but will save one who might be reading of this.

  I am up to date on all updates for my Mac. If anyone have REAL answers so please spilling the beans, but according to me, it's the only truth is that Apple has rolled out a product inferrer to replace an exceptional product, called iPhoto, which does not work on my new iMac computer 5K of 27 ".   If I knew what I would have chosen another computer that I use iPhoto to prepare more of fifty to sixty thousand photos in a given year and I use iPhoto to make hundreds of slideshows from it.  Are there plugins for Photo 1.3? I ask because I see where there could be Add-ons, but I can't find.

  Apple has taken a serious decision by turning his back to iPhoto and tens of millions of loyal users.

  Thanks in advance to anyone brave enough to tackle this job.

  James

  First, back up your library of Photos and hold down the command and option keys while launching Photos - repair your database - you have a corrupted database

  LN

• Looking good 4 k monitor for end of 2013 Mac Pro

  I just ordered and received the LG 4 k monitors but when comparing them with the Apple thunderbolt display monitor they were still close in brightness or color rendering. They had an orange very little the cast to them. They were the 31MU97C-B models and I could not find any reviews on them. They were actually newer and cheaper than the model 31MU97 (without the C - B).

  So I sent them back. They were only 900 each, shipped. Is there anyone in the sound of my voice who can tell me a good 4 k monitor about the same price comparable to the Thunderbolt display, but in 4K? I've searched high and low.

  Thanks in advance

  James

  Take a look at BenQ monitors. I use a pair of 24 '' those on my Mac Pro 12-core gaming and they are great. I got them to Fry. mine are not K 4s, but you could do a search and check BenQ 4 K specifications and perhaps find a store with some on display to check. Mine give identical color between the 2, so their QC is decent. (I got a pair of ViewSonics never able to calibrate to match!) They make the ViewsSonics (attached to my older PowerMac G5 and sat next to my Mac pro) look really weak and pale on the best settings of ViewSonic.

  http://4k.com/monitor/a-review-of-the-benq-bl3201ph-32-ips-led-4k-monitor-with-3 2-led-lit-screen inches / is a review on the BenQ 32 "4K that Amazon sells for slightly less than $900. Be sure to watch the 3201PH against the PT. 3210 (who sell the FRY and even Wal-Mart) I don't think that the PT would be like good video. (he does not mention 4K on his form and sells for hundreds less.)

• HP psc 2210: clear jam on my hp psc 2210 all-in-one printer

  The lights on my printer and the message says: "open the door.  "Clear carriage jam, and then press ENTER.  I do not see a "jam", opened the door and press enter several times.  I still can not reset unplugged machine from one day to the next.

  I think the cartridges are "stuck" on the side of the machine and they are unable to drag in the middle.  Can someone tell me how to fix this jam?

  Would be very grateful for the help!

  Renee'

  Hi @sreneecesand welcome to the Forums of HP!

  I see that you are having problems with jam.  I would like to help!

  I recommend starting by remove (if possible) ink cartridges and perform a power reset the printer.  Unplug the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug back in the printer. Make sure that you connect the printer directly to a wall outlet. Make sure to bypass any surge protector or power bar.
  
  I would also say to following the steps outlined in this document:

  A display of the Error Message of "open door, clear transport jam, and then press enter" for HP PSC 2170 2100 and 2210 all-in-One Series Printer "

  Good luck and please let me know the results of your troubleshooting operations. Thanks for posting on the HP Forums!

• 1315 all in one printer: my 1315 all in one printer shows "paper jam".

  My 1315 all in one printer shows "paper jam" even if I can copy directly, and it has good connection with the computer, there is no jam. I also changed the ink cartridges to see if that helps - it is not.

  Thank you for your help. I tried everything, but it didn't work. In the end I tried to change the port to USB port on the computer and we are back in business. The printer was the problem, it is the port. I hope this helps someone.

• 5520 all in the transport of a printer jam

  I unplugged, turned off moved round-trip transportation, and again, it will not be printed. Before it stopped working it's some unpleasant noise like a machine gun. I guess that is not a good thing? Please help or is this another throw away?

  Welcome to the forums cp64

  I saw your post on your Photosmart 5520 is more printing and already make loud noises. There could be some paper stuck in the printer itself. I would say by following the guide below. Make sure that pay you special attention to cleaning the rollers as well. Sometimes a good cleaning can solve the problem!

  A "Paper jam" Message appears on the control panel

  If troubleshooting doesn't help not solve your problem, then I would say call the HP Technical Support to see all the other possibilities for you. If you call in North America, the number is 1-800-474-6836 and for all other regions: click here.

  Thanks for posting, have a great day!