Join a computer to a domain loop does not...

Similar Questions

• SR400 while the loop does not work

  Hello

  I'm using LabVIEW for control SR400 through a GPIB card.

  I use SR400 to count the number of signal in a second, wait 0.05 s, then again count the signal once, wait 0.05 s once again, and so on.

  However, the while loop didn't iterate. When I started the program, it is only once.

  In execution of highlight mode, when an iteration is finished, he waited a long period starting the next. In normal mode, it doesn't have to iterate.

  Also when I clicked the stop button, it's been clicked. However when I wrote a very simple program, the stop button worked normally.

  In any case the button issue is not very important. I don't care that the program iterates forever or not. I just want to iterate.

  I searched the jury and had not could not any related problem.

  Is it better to attach my VI? The VI is in my computer lab.

  Thank you very much!

  This code just feels bad.

  (No real management mistakes, deep, stacked sequences FOR lines that are wired to iterate through only once, controls on the right and right to left, wiring weird code on average the last 10 items (Hint: means ptbypt with a length of 10 sample he would!).) If you want to use the wire of the error, the sequences would not even necessary)

  If the stop button does not reset, it means that the iteration of the loop does not terminate. It can fill in only if the two structures of the sequence ends.

  Have you tried running in execution, emphasizing fashion while looking at the diagram? Probably one of the communications is at a standstill. For example, the instrument sends really 6 bytes at the end? When you set the overall timeout and what is it?

• one of the usb devices attached to this computer has malfunctioned and windows does not recognize it

  I get the following message when I join my computr "one of the usb devices attached to this computer has malfunctioned and windows does not recognize," my nokia C3
  kindly help

  Most often when a device is not it's because of a driver.  Try reinstalling your.

  It works for win 7 & 8

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly? SignedIn = 1

  http://captaindbg.com/how-to-update-drivers-on-Windows-7/

• HP g6-1b60us: my computer hp g6-1b60us laptop does not light.

  My computer hp g6-1b60us laptop does not light.  It was working fine last night. When I tried to turn it on this morning, it not light. When I press the power button, the led by the power cord light flashes 3 times.  I tried the hard reset (remove the battery and the power cord and press the power button / stop for 30 seconds).  What can I do else?

  Please disregard the previous post. I tried a hard reset a second time and was able to get it to the top.

• Error one of the UBS damage connected to this computer has malfunctioned and windows does not recognize it

  Original title: Canon MF 4500 printer inkjet

  My computer tells me that 'one of UBS damage connected to this computer has malfunctioned and windows does not recognize"it could the cable, as the printer (canon MF 4500) does not work.

  Hello

  1. what operating system is installed on your computer?

  2. when exactly you receive this error?

  3. all USB devices work properly on your computer?

  4. have you made changes on the computer before this problem?

  Method 1:

  You can try running the fix - it from the following link.

  Hardware devices do not work or are not detected in Windows

  http://support.Microsoft.com/mats/hardware_device_problems/

  Method 2:

  You can try to uninstall and reinstall the USB controller. Follow the steps.

  (a) click Start and then click Control Panel.

  (b) click System and Maintenance, click System, and then click Device Manager.

  Note: If Control Panel is in Classic view, double-click System and then click on Device Manager.

  If you are prompted for an administrator password or a confirmation, type the password, or click on allow.

  (c) in Device Manager, double-click to expand the "USB Bus controllers", right click on the controller host, click "Uninstall" and click "OK".

  Check that if at all, there is an exclamation point on the pilot, it suggests problems with the installed driver.

  (d) repeat step 2 to uninstall all items under 'USB Bus controllers'.

  Then, restart your computer and Windows will automatically reinstall all USB controllers.

  It will be useful.

• One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it. The location is the root (2 ports) USB hub: 1-unknown device and Port 2-not used

  Original title: USB device not recognized

  Over the last 2 weeks, I get a message on a USB device.  The message said that one of the USB devices attached to this computer has malfunctioned and Windows does not recognize it.  The location is the root (2 ports) USB hub: 1-unknown device and 2-unused Port.  I have no idea what it means.  I hesitated to first click the icon (it does not last very long) thinking it could be a scam.  Can someone help me?  Thank you.

  Hello

  (1) is the specific question of specific USB devices?
  (2) did you of recent changes to the computer before the show?
  (3) have you tried plugging the USB stick on another computer?

  (4) what is the brand and model of the computer?

  I suggest to refer to the following methods and check if it helps to solve the problem.

  Method 1: Hardware devices do not work or are not detected in Windows

  Run Microsoft Fixit mentioned in the article.

  http://support.Microsoft.com/mats/hardware_device_problems/en-us

  Method 2: USB Port may stop working after you remove or insert a USB device

  http://support.Microsoft.com/kb/817900

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 How to back up and restore the registry in Windows

  Reference:--

  Advanced troubleshooting tips for General USB for Windows XP problems: http://support.microsoft.com/kb/310575

• Error - "one of the usb devices attached to this computer has malfunctioned and windows does not recognize it

  Original title: USB device not recognized / dysfunction

  "Unrecognized USB device".
  One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it. Help for this problem, click this message. »

  This is what I get AFTER that I had to reinstall windows XP because a virus has attacked my computer a little before avg and Microsoft security essentials picked it up and destroyed... I have reinstalled twice... then I changed discs since I have two... well, I get this message from my 2 external Seagate Freeagent and my Phillips mp3 go gear aria... player these devices work on the laptop from my friend and she is under vista. It seems that since then they have worked on my computer before they would always run. My mouse and my cam work fine and my Canon printer gets thus detected... a few readers who have the space that is made... Ive looked everywhere for a solution... even upgraded windows media 11 and is player went to service pack 3. restarted several times... tried dPower Management tab and tried to

  Open recognition of the USB device by using Device Manager.

  .. I am at a loss: P please help thanks!

  isable the power management of the USB hub and I couldn't find the

  Hi LadyDefi,

  You can try to uninstall and reinstall the USB controllers and check:

  To remove and reinstall all USB controllers, follow these steps:

  a. Click Start, click Run, type sysdm.cpl in the Open box and then click OK.

  b. click on the Hardware tab.

  c. click the Device Manager button.

  d. expand Bus USB controllers.

  e. right click on each device under the Bus USB controllers node and then click on uninstall to remove them one at a time.

  f. restart the computer and reinstall the USB controllers.

  g. plug in the removable USB storage device and test to make sure that the problem is solved

  For more information, see the following article:

  Advanced troubleshooting tips for General USB for Windows XP problems

  http://support.Microsoft.com/kb/310575

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• I try to install vista on a computer running xp. XP does not even recognize the vista disc is in the drive. XP recognizes any other drive that I use and the vista drive is recognized on other computers, that I put it in it's not a prob with the disk or cd

  I try to install vista on a computer running xp. XP does not even recognize the vista disc is in the drive. XP recognizes any other drive that I use and the vista drive is recognized on other computers, that I put it in it's not a prob with the disk or cd rom

  The Vista installation disc is a DVD. Apparently, you don't have a DVD player. You would need to purchase/install a DVD-ROM or DVD - RW to install Vista. Are you sure that your hardware supports Vista before doing this?

  http://www.Microsoft.com/Windows/Windows-Vista/get/system-requirements.aspx
  Even if a minimum of 1 GB, the requirements in the real world Vista requires a minimum of 2 GB of RAM to run without problem. You will also need Vista drivers for all your hardware.

  http://www.Microsoft.com/Windows/Windows-Vista/get/Upgrade-Advisor.aspx MS - MVP - Elephant Boy computers - don't panic!

• Error "one of the USB devices attached to this computer has malfunctioned and Windows does not recognize it." when you connect Logitech M225

  Original title:

  My wireless mouse works fine for the last 2 months, now, all of a sudden it doesn't work at all.

  I get a windows notification that says-

  "One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it."

  I have Vista 32 bit OS on my laptop.

  My office has Windows 7 32 bit and I am able to use the mouse on this computer, then the M225 is not defective.

  I tried to look for a download of update on the site of Logitech & only found:

  6.32.20 set - point it did nothing to help.

  I also tried to move the receiver to the other 2 ports USB w / still the same results.

  Are there other downloads or solutions that will help w / this problem?

  You can also try searching for devices strangers (with yellow symbols) in the Manager under the mouse devices and other pointing devices and other devices (if any). Right click and uninstall unknown devices. Then restart.

  Also try the steps below to reset the power of USB:
  (a) the laptop off, unplugged from the wall outlet.
  (b) remove the battery for a few minutes, then reinstall it.
  (c) then restart the laptop.

• Windows 7 and install/recognize the problems of printer HP LaserJet P2015 error - USB Device not Recognized One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it.

  Title: Windows 7 and install/recognize printer HP LaserJet P2015 teething problems...

  I have a dell inspiron that was originally windows Vista and I changed to windows7.  I have a LaserJet where I work, a HP LaserJet P2015 printer and when I plug in the USB, it says (peripheral USB not Recognized One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it.

  How and what should I do to get the printer going or to get the computer to recognize.  Installation CD will not work and I looked online and downloaded drivers but still the same thing.

  Hi LOliver,

  Method 1: Run the hardware and peripheral troubleshooting tool and check if it makes a difference.

  Open the hardware and devices Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-hardware-and-devices-Troubleshooter

  Method 2: Disconnect all USB (Universal Serial Bus) devices connected to the computer (unless your mouse and keyboard). Connect the printer and check to see if the problem persists.

  Method 3: Connect the printer to a different USB port and check.

  Method 4: Reinstall the USB (Universal Serial Bus) controllers.

   First of all, please disconnect all USB devices and then perform the following steps:

  (a) click on 'Start', type device manager in the search bar and press "Enter." If necessary, click on continue.

  (b) in Device Manager, double-click to expand the "USB Bus controllers", right-click on the "host controller", click "Uninstall" and click "OK".

  (c) repeat step 2 to uninstall all items under 'USB Bus controllers'.

   

  Then, restart your computer and windows will automatically reinstall all USB controllers.

   

  HP printer drivers- ensure that you download the driver appropriate for your device model package.

   

  Thanks and greetings

  Ajay K

  Microsoft Answers Support Engineer
  ***************************************************************************
  Visit our Microsoft answers feedback Forum and let us know what you think.

• "One of the USB devices attached to this computer has malfunctioned and Windows does not recognize it." Why it does not recognize my device?

  Some time ago I had a huge problem with my computer (I think that my mother-in-law accidentally downloaded a virus) and I took it to a repair shop where they wiped out completely and replaced the hard drive.  Since I got it back when I try to use my wireless mouse and plug the nano receiver he said 'one of the USB devices attached to this computer has malfunctioned and Windows does not recognize it.  Why he says this?  And what can I do about it if anything?  I already tried uninstalling the driver and reinstalling, but that did not work because as soon as I plugged it it again once he says the same thing.  So I don't know what is happening or how to fix it.  Please help me!

  Hi Carla,.

  Please go to the Microsoft Community Forums.
  After the description of the question, I understand that you can not use the mouse on the computer wireless.
  Let me go ahead and help you to question
   
  What is the brand and model of the mouse?
   

  Here are some ways you can follow to resolve the problem:

  Method 1:
  Try to connect to other USB port and verify.
   
  Method 2:
  I suggest for the link and follow the steps in the article:
  Troubleshoot a wireless mouse that does not correctly
  http://support.Microsoft.com/kb/321122#appliesTo
   
  Method 3:
  Remove and reinstall all USB controllers
  Follow these steps:

  a. click Start, click run, type sysdm.cpl in the Open box and then click OK.

  b. click on the hardware tab.

  c. click the Device Manager button.

  d. expand Bus USB controllers.

  e. right click on each device under the Bus USB controllers node and then click Uninstall to remove them one at a time.

  f. restart the computer and reinstall the USB controllers.

  g. plug in the removable USB storage device and perform a test to ensure that the problem is solved.

  
  I hope this helps. If you have any other queries/issues related to Windows, write us and we will be happy to help you further.

• Computer HP dm4-1160us laptop - does not work - has a white when turned on screen.

  Computer HP dm4-1160us laptop does not work - it has a screen white when turned on.

  See this page for "no starup" advice, if none of these tips help, the laptop will need professional diagnosis.

  Go to this page, select "Error Messages displayed on the computer"

  http://h10025.www1.HP.com/ewfrf/wc/documentSubCategory?tmp_rule=43716&tmp_task=solveCategory&cc=us&DLC=en&lang=en&LC=en&product=4308941

• Loop does not complete

  I have a simple loop in a function I use to remove all elements in the array:
  

  for (var i: int = 0;  I < tempArray.length;. i ++)

  {

  tempArray.pop ();

  trace ("pop:" + tempArray.length);

  }
  
  The probelem I'm having, it's that the loop does not terminate. It seems that to remove a single item, sometimes it will remove two. An event that is triggered in a separate function you may this prevents from running until the end?

  is there another method I could use to remove all items?

  use:

  for (var i: int = tempArray.length - 1; i > = 0; i--)

  {

  tempArray.pop ();

  trace ("pop:" + tempArray.length);

  }

• Conditional loop does not work correctly.

  Hello
  
  If you look at my code, its all about the analysis of a dictionary. IM check the dictionary for the word 'aardvark '. It gives me wrong all the time. When "aardvark" is the first word of the table, IE my_dictionary [0] is "aardvark". I wonder why the conditional loop does not work very well. IM checking if the user string aardvark is == my_dictionary ; he should give me the true value.
  
  Is there an error in the code? Can someone explain to me where im going wrong?
  
  PS-> put everywhere traces gives me the right output. Except for the result of the if() function.
  
  Best regards and many thanks in advance.
  Roshan Kolar

  Hi Raymond,

  Thanks for the reply. I had the problem, actually the conditional loop was perfect, the analysis was not. The reason is, a few words in the dictionary had a return of cart/jump of line/space to the index of the last after the word. It was randomly, so some words have been taken, but some were not as "vicious" == "vicious" - gives the INVALID WORD.

  So I was thinking about the parser, where I removed the unwanted last tank - now the condition has worked well. Thank God I worked even after the publication of the request.

  Thank you very much Raymond.

  Kind regards
  Roshan

• Impossible to join a computer to a domain in workstation 8

  Hello guys,.

  I am Runnig 2 machine Workstation 8 on my laptop, a computer is a Server 2008 R2 after DCpromo and other machine running Windows 7.

  The problem is that I can't join Windows 7 to the domain. I already join the computer in the ad on my server, and still I can't seal the computer to the domain.

  And seriously do not know how to connect the two machines.

  Thanks for any help

  Kudo

  FYI - in the DCpromo Seup to choose the first option (Yes), that it is related to my problam?

  With your NAT configuration, you need to know is:

  Subnet: 192.168.71.x

  Mask: 255.255.255.0

  Gateway: 192.168.71.2

  DNS server: 192.168.71.2

  Static address range: 192.168.71.3... 127

  DHCP addresses: 192.168.71.128... 253

  The DHCP server address: 192.168.71.254

  Broadcast address: 192.168.71.255

  An example of how you can set up your virtual domain environment is to disable DHCP for the NAT network in the virtual network editor and configure a DHCP server with the settings on the domain controller. This would allow you customers who get their correct IP configuration from the DHCP server on the DC, without having to manually configure installation.

  Example of domain controller configuration:

  Name of DC: dc1

  Domain: lab.local

  IP address: 192.168.71.10

  Subnet mask: 255.255.255.0

  Gateway: 192.168.71.2

  DNS server: 127.0.0.1

  Configuration of the DHCP server:

  Range: 192.168.71.100... 127

  Subnet: 255.255.255.0

  Gateway: 192.168.71.2

  DNS server: 192.168.71.10

  The DNS server configuration:

  Transmission to: 192.168.71.2 (all names other than the own domain)

  André