JOINT-2: Tips for the initial configuration of the network?

Similar Questions

• The settings saved on this computer does not meet the requirements for the network

  My old laptop connects fine but my other not.  When I go to connect to the network, it says "the settings saved on this computer does not match the requirements for the network."

  Hello Tazdmx83,

  Thanks for posting on Microsoft answers Community Forums.

  This problem usually occurs on wireless network connections. I suggest that you turn off any wireless security feature by following the steps below.

  1. click on start and control access panel.

  2. double-click on network connections

  3. right click on the wireless adapter and select Properties.

  4. Select wireless networks, click the name of your wireless network and choose Properties.

  5. in network authentication, select open to disable wireless security.

  6. Please try to connect.

  If the problem persists, I suggest that you remove the connection and re-create the wireless network connections. The following Web site can help you on the creation of the wireless connection.

  http://windowshelp.Microsoft.com/Windows/en-us/help/297fa2dc-B20B-4327-B673-707a968c86801033.mspx

  Important note: Microsoft provides third-party contact information to help you find technical support. These details may change without notice. Microsoft does not guarantee the accuracy of this third-party contact information.

  If the problem persists, I suggest you reinstall the driver of card wireless network and Re-create the connection.

  Remove the driver for the card
  ========================

  1. click on start. In the start search box type "devmgmt.msc", and then press ENTER.
  2. expand "Network adapters", double-click the entry for the wireless network device.
  3. click on the "Driver" tab, click "Uninstall".
  4. click on start. In the start search box type "appwiz.cpl", and then press ENTER.
  5 remove the entries related to the wireless network adapter.

  Reinstall the driver with your CD of drivers on the manufacturer's Web site. After installation, create the connection.

  Also access the link and try to follow the steps in troubleshooting network related issues on Vista-based computer:

  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  It will be useful.

  Thank you and best regards,

  Srinivas

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think

• 'the settings saved on this computer for the network do not match the requirements of the network.

  original title: securtity settings in my computers. where should I go and see what are my security settings?

  the settings saved on this computer for the network do not match the requirements of the network.

  where should I go and see the settings?

  Hello Arturito1,

  Thanks for posting in the Microsoft Answers forum! For assistance with your question, I would recommend that you follow the steps provided by Srinivas R in the thread below:

  http://social.answers.Microsoft.com/forums/en/vistanetworking/thread/a82432f2-9312-480A-b2ea-720033c73387

  Hope this helps J

  Adam
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• ' Error' the settings saved on this computer for the network do not match the requirements of the network "while trying to connect to the wireless network

  Title: Cannot get an Internet connection!

  Connection Wi - Fi comes with a warning that 'the settings saved on this computer for the network do not match the requirements of the network"what should I do to get a connection?

  Hello

  -Did you do changes on the computer before this problem?
   
  Method 1: I suggest you follow the steps to run the troubleshooter from the
  link and check if the problem persists.
  Using the troubleshooter from network in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7
   
  Method 2: I also suggest you to follow the steps from the link and check if it helps.
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows
   
  Method 3: Follow the steps below to remove and add the wireless network.
  (a) click Start and select Panel.
  (b) select network and sharing Center and manage the networks without wire (on the left).
  (c) in the list, click on your network and Remove top.
  (d) you can then search for available wireless networks again and reconnect it to your network.
   
  Hope this information helps.

• Tips for the replacement of DVD burners on Tecra series

  I think I need to replace my DVD burner. I used a carpet * a UJ-811 t came with the laptop, but it is no longer Burns correctly, although he continues to play well. Initially, I thought it was a problem with Nero (calibration error), but it doesn't matter what burning program I use. I spent a weekend through various forums looking for a solution: I ran a lens clean and updated drivers, looked for the firmware updates (nobody seems to be able to find for the carpet *, including on the Firmware Page), tried the brands of different media (although I initially using Sony and TDK in any case). All with no luck. So I think that he has reached the stage that I need to replace the burner itself.

  So, advice on brands and type? I want something that is internal and easy self-installation. I would like to also buy online and get fast shipping (I'm leaving Ireland in about a month) so also website suggestions welcome. Please keep your relatively simple tips; I am a relative novice who learns quickly.

  Thanks in advance.

  Hello

  It's a shame! It of always frustrating when the player no longer works!
  But there is not much to do! You said that the calibration error message appears.
  Well, it seems that the drive cannot calibrate the lens correctly and this leads to problems of engraving!
  As you already assumed the replacement drive is required!

  Usually, the user that was preinstalled on your laptop manual should provide some compatible readers and supported!
  Check it! My user manual contains this info!

  But if you don t find anything, I recommend you contact the ASP in your country for the disk drive!
  You should know that not all readers are compatible because of the master/slave/c-salt settings.
  If the drive supports bad settings of the BIOS does not correctly recognize this device!

  So, make a call to the service provider and ask for more details! Good luck

• HP 15 J8X12UA #ABA: what is the size of tip for the power adapter for laptop HP 15

  Can anyone provide the specifications for the tip of the HP 15 laptop power adapter? I'm looking for more details on the size.

  Thank you.

  Bill

  Reference number:

  45 W HP Smart AC adapter (NFPC, RC, 3-wire, 4.5 mm) 741727-001. 19.5V 2.31 HAS 45W

  Here is a picture with the dimensions of the cutting edge. If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

  

• Satellite A60-142: Tips for the new laptop

  Hi all

  I think to buy a new laptop.
  I currently have a Satellite A60-142 and I only am not too thrilled about this model since the fan makes me crazy... It is constantly running and compared to my old laptop (Satellite 1410-304), it makes a lot of noise...

  So, I want to get a new laptop which is quieter...
  I need basically for email/surfing/Online games/digital still camera.

  Thanks for the tips!
  Ellen

  Hi Ellen

  Well, it is a known issue that, often, the fan works. If you play games or use other applications, the laptop works at high performance and the parts of the device as the processor or graphics card produce a lot of heat. In this case, aeration run also at high speed. It is a simple fact.
  As far as I know, you can try to change the settings of cooling in the power utility.
  In addition it is not easy to say which model of laptop runs more quiet. In the notebooks of high performance fans are bigger and louder by contrast office books are ineffective but easier to cool.

  It's not easy to make a choice

  Good bye

• OfficeJet Pro 8500: Officejet Pro 8500 A910 - unable to access configuration for the network folder screen.

  I can't access my webpage "network folder Setup.

  I can access my page main printer very well using the IP of the printer.   I click on Scan up fine, I then click on "configuration of the network folder" and it tries to load and then goes to a screen "ERR_CONNECTION_TIMED_OUT".

  He warned me the first time that he has been using HTTPS and I approved that.  I currently records on my printer set up awhile back and they work fine but must modify and add a little more.

  I tried multiple computers and devices with the same results.

  Thank you

  Chris Gaines

  MALVERN, AR

  Hello @Cgaines78,

  Thanks for dropping by the HP's Support Forums! I see that you run into issues trying to set up a folder network for your HP Officejet 8500 A910.

  Please continue troubleshooting here: scan to a computer, the e-mail, the device memory or the network folder

  This aid? You are now able to set up a network folder?

  Let me know the results. If this resolves the problem please let others know to mark this message as "accept as Solution".  Just say thank you, please click the ' Thumbs Up ' button. If you need more assistance let me know and I will gladly do whatever I can to help.

• Configuring the private network or disable questions for the network discovery in network and sharing Center.

  I just got my laptop all cleaned and had everything updated. When I got it back I was mainly concerned how my network and discovery sharing would work, because we never had a home computer and a laptop computer at a time. Our PC at home has always defined for a private network. Today, they are both defined for the private sector, the laptop will probably always be at home too, but I was curious to see how the printer share everything would work on my laptop. It would not print and I checked just the settings that the guy I of any program for me usually had the top settings. On my laptop that I was first checking out and the network discovery has been to custom on both, one on my PC was on, laptop has never been verified we or off, file sharing has been enabled on both. public folder sharing off on both, printer sharing turned off the PC at home, but on laptop, so much time, I guess me to turn on the PC I don't know yet. Printer password sharing is on the PC and laptop. I try essentially whether it is what you would call a custom setting make for a firewall setting, or could someone please just kinda tell me if the sharing of network discovery should be turned on on the laptop and the PC, or was it not suppose to be turned on to the laptop, but on the PC only? Which should be lit and which should not be enabled in the configuration of the private network? I just want to be able to print my laptop if I want to. Thank you

  [Moved from the community centre of Participation]

  Hello

  What version of Windows are you using?

  This article was written for the two Windows Vista & Windows 7.  Drop-down menu (right) allows you to activate Windows Vista Instructions.

  http://Windows.Microsoft.com/en-us/Windows/install-printer-home-network#1TC=Windows-7

• OfficeJet pro 8600 + scan if there is no configuration for the network folder

  The printer is wireless to my router and I connect to a computer connected to the router with an ethernet cable.  The computer is running Windows 7SP1 Home Premium 64.

  During the original installation of the printer 3 days ago, I used the wizard set up 'scan to a network folder' a record 'scans public '.  He created the 'profile' correctly and worked well the first time I scanned (I scanned the 3 or 4 times with different tweaks to experiment).  However the next day it no longer worked error on the printer was, 'could not connect to \\Computername\Public scan. Check that the remote computer is on. "Obviously, the computer was on, some communication problems only happened from one day to the next day, he was sitting unattended.  Hmmmmm.  Note that the option "Scan to Computer" works very well, so communication is simply no "scan to network folder" option and I really want to scan to a network folder.

  I went in a private "Scans" folder on my account and created a share as 'DadsScans', creating permissions and following all the tips I've come across so far.  Then I tried many times with the wizard to create a new configuration in the profile and all have failed and yes I found the network and turned on file sharing.  Also remember that it worked fine the first night?

  I tried to enter the local path to the folder (C:\users\dad\My analysis) with a share name (DadsScans), but the error message after choosing the option "test and save" was, "error.  Your printer cannot connect to the server.  Press 'Back' to correct the address and the name of the server.  Setting is not saved. »

  I then tried to enter the share name directly in the path of the network folder, like "\\computername\DadsScans", but the error was "error.  Your printer cannot connect to the server.  Press 'Back' to correct the address and the name of the server.  Make sure that network discovery and file sharing are turned on... "Note, I also tried,"\\computer Address\DadsScans IP"and got the same error.

  Finally, I disabled my firewall and my anti-virus in real time and tried again and got the same error messages.

  Once again, my network discovery and file sharing are on and it worked fine the first time I've used suggesting that everything was fine.  What happened during the night, so that the printer and computer sitting idle?  I've changed NOTHING!  Any suggestions would be greatly appreciated!

  Well well, after several hours of attempts to solve the problem, the 'light bulb went on!  The night after that I configured the "scan to network folder" option, we had some difficulties with our network so I reset our modem and DSL router.  Who cleaned the problems of network with devices.  It is apparently broke something with the communications between the scanner and the computer.  A simple re-start the computer tonight and wa - la, the original public scan I configure worked again and I could create new profiles of "scanning to '!

• Tips for the TCP wait of asynchronous Messages with non-standard expression tanks

  Hi all

  I have a PITA instrument that I need to communicate with in a system of greater control.  This instrument communicates via RS232 to a server running on the PC OEM application.  In order to communicate with the instrument, I have to use the TCP protocol on a specific port on Localhost - So far so good as long the protcol is answer command.

  The problem is that the instrument sends several messages asynchronously of different sizes with a double newline as a tank of termination (there are many CR/LFS all these messages so that they cannot be a MOE) and I am struggling to find a way to manage receive asynchronous messages of variable length with a cusom CHARACTER term. without having simply a fast dedicated for TCP loop reads trying to catch these asynchronous status messages.

  I wish the functions VISA TCP has worked with the local host, given that the properties that can be set to change the chariot of non-standard term.

  Open to suggestions-

  Thank you

  Ronin

  Yes, I'll be streaming in my own string buffer and then to choose the messages out of the buffer when you find the stop character.

  A technique to improve performance, rather than reading a single byte at a time is to use the "immediate" on reading TCP mode and use a high value for the "bytes read" - in this way, it will return all of the data that is there without waiting for all the specified bytes or the time-out. He will wait only the full timeout if 0 bytes are received (which you can ignore) - set to a low value such as 100ms.

• Some tips for the Windows Live Mail 2011 0x8E5048 fixing error code?

  Live Mail not keep open, indicating that my calendar is corrupted.  Above the error code

  Hello EugenePressman,

  The best place to ask your question of Windows Live is inside Windows Live help forums. Experts specialize in all things, Windows Live, and would be delighted to help you with your questions. Please choose a product below to be redirected to the appropriate community:

  Windows Live Mail

  Windows Live Hotmail

  Windows Live Messenger

  Looking for a different product to Windows Live? Visit the home page Windows Live Help for the complete list of Windows Live forums to www.windowslivehelp.com.

• Tips for the uprgrades to HP Pavilion 500-281

  I would switch to another power SUPPLY and a better video card and 4 GB of ram. What should I know about the upgrade of each party and to ensure that it works with other parties?

  Bob, welcome to the forum.

  Here is the memory upgrade information for the computer:

  • Dual channel memory architecture

• Tips for the custom transformation script change the Associations of FK table

  Hello
  
  I try to write a transformation script that will scroll through tables in a large model and change some
  FK associations to change the remote table at CF. By the way, the reason is that our logic model
  the logical entities that represent many areas of codes of small research. However, our relational and physical model has a
  utility single physical filing table of codes that contains all areas of these codes. Therefore, a part of the transformation
  our logic model for the relational model is to swing all FK associations for these areas of research codes
  in the table of common code. Then the paintings representing the research areas can be removed from hard.
  
  In any case, I'm looking at the
  
  oracle.dbtools.crest.model.design.relational.FKIndexAssociation
  
  or the
  
  oracle.dbtools.crest.model.design.relational.Index
  
  to see if one of them can be manipulated to perform the transformation I want to accomplish.
  
  When I perform the equivalent process manually via the property sheets there are several ways to address this problem.
  
  (a) the method more jolise seems to change the FK in place by clicking on the FK in the relational schema and changing
  the property called ' PK / UK Index'. Change that to the pharmacokinetics of utility code repository table that replaces the original
  table (which represents the research field). A side effect of this translates into CF mapping
  columns being nulled out. They must be remapped to original columns (which are kept).
  So in two stages, the existing FK is detached from the original, attached table to the new table, and then
  FK columns are reused in place for new CF mapping.
  
  (b) the brute force method is to remove the original FK and then create a completely new FK to the new table. There are
  several dialog boxes that allow you to keep the original FK columns and use them in the new FK.
  
  I realize, this is a somewhat complex transformation, but I would like a few algorithmic advice on which path to take
  to try to achieve. In particular, there is a script that is equivalent to that of the first process above?
  
  I don't even know if the CF which is represented on the relational schema is represented by the FKIndexAssociation or Index
  class in the script object model. In other words, I have to loop through the tables in the relational model what would be my
  starting point:
  
  FKS = table.getFKAssociationsList ();
  
  or
  
  fkIndexes = table.getAllInds_FKeyInds ();
  
  or something else. The names of the properties in the user interface are always with the properties of scripts not so
  It's a little difficult to understand such things.
  
  Once I have access to the object that is equivalent to the FK in the property/diagram worksheet, which
  is the best way to handle via script. How can I change the end of parent and away from CF to point to the new table.
  Or if I have to delete the original CF and then re-create - is there a way to save the original FK columns and reuse them
  While creating the new FK?
  
  ********************
  
  Another question. What is the best way to remove tables from a relational model. I note that there is a remove() undocumented (?)
  a method that is available on the Table. It's probably a superclass to remove other things as well.
  
  When I try to use this method in a loop the script throws up to dialog boxes that are similar to dialog boxes that are displayed during the execution of a removal
  manually through the user interface. Is it possible to intercept and answer dialogs programmatically?
  So for example if I get a window of dialogue as
  
  You want to remove generated columns of FK 'FOO' in the table 'BAR '?
  
  is it possible to intercept this dialog in the script and then answer Yes or no it via the script?
  
  ***************
  
  If it is too difficult to perform this type of transformation with the help of script
  is to do the transformation on the generated DDL file. But it would be cleaner to
  to do the transformation in the relational model DM if possible.
  
  All advice appreciated.
  
  Rgds, BP

  When I try to use this method in a loop the script throws up to dialog boxes that are similar to dialog boxes that are displayed during the execution of a removal
  manually through the user interface. Is it possible to intercept and answer dialogs programmatically?
  So for example if I get a window of dialogue as

  You want to remove generated columns of FK 'FOO' in the table 'BAR '?

  is it possible to intercept this dialog in the script and then answer Yes or no it via the script?

  It's in the preferences - "Data Modeler > model > relational > remove FK column strategy."

  I don't even know if the CF which is represented on the relational schema is represented by the FKIndexAssociation or Index

  Is a pair of two - FKIndexAssociation, that's what you see the pattern, but it is hidden in the table index - isFK() returns true for this type of index and you can take FK with getFKAssociation()

  Once access to the object that is equivalent to the CF in the property/diagram worksheet

  table.getFKAssociations () - returns an array of the foreign keys;
  You can get to them from the relational model:
  model.getFKIndexAssociationSet () .toArray () - FK all model

  How can I change the end of parent and away from CF to point to the new table.
  Or if I have to delete the original CF and then re-create - is there a way to save the original FK columns and reuse them
  While creating the new FK?

  There should be no problem if you use the same number of columns with the same data type and order:

  get the current FK columns
  columns = fk.getColumns ();
  newRefKey is the new key question; referred and child columns must match the data type and the order in the keys - you do not ask how to get
  fk.changeKeyObject (newRefKey, columns);

  function setting in preferences, you will get the question on the columns of FK.

  Therefore, a part of the transformation
  our logic model for the relational model is to swing all FK associations for these areas of research codes
  in the table of common code. Then the paintings representing the research areas can be removed from hard.

  You can create the hierarchy of entities with the root attribute (and PK identifier) KP holding entity and entity - your look-up - empty child relationships will be these entities of the child. With the help of the transformation of the "unique Table" you will get what you are trying to achieve now with script.

  Philippe

• Win7x64 with adapter DWA-160, "Windows could not automatically bind the IP protocol for the network card stack."

  As the title suggests, I am running Windows 7 family, 64 bit. This is a new installation, a few days ago and I have not installed anything on, or changed the settings.

  I installed a DWA-160 D-link Wireless adapter n with the current drivers, fix (before you ask to confirm, they come from Web site of D - link. I used initially the disk included in the box, however, this has generated the same question that I'll explain, so I uninstalled this software and has continued to use the Windows program to connect to the wireless network.

  I can connect to the network, of course; However, I get the message "Windows could not automatically bind the Protocol IP on the network card stack" when connecting each time.

  After searching for an answer, I tried to turn on the WLAN auto configuration service, however, it is enabled by default. If this isn't any help.

  Tried the netsh winsock / netsh int ip / netsh int ipv4 / netsh int ipv6 reset and restarted after each, no change, if this isn't any help.

  Made sure the problem wasn't with the wireless router, and it isn't because I can connect with my laptop.

  Tried to plug in the USB stick on another computer yet. I don't want to plug into my laptop just to test that possibility. So. Yes.

  I also don't know much about all the inner workings of one of these things, so it would be rad If everything was in one step by step. Thanks in advance.

  Try to run This Fix - It.