L2l multiple rays routing traffic

I have a problem I hope you can shed some light on this. I have all 3 sites connected with VPN/IPsec ikev2 tunnels using ASA 5505 and 5510 with 8.4 + code. Please see the image below for more details on my installation. All VPN tunnels are up and send traffic across the immediate neighbor, the problem is that I can't ping or access the ASA2 subnet ASA3 subnet or ASA2 of ASA3, that I'm missing in my setup? Please see below and thank you in advance for any help you can provide this.

ASA 3 VPN Config:
protocol esp integrity sha-1
crypto ipsec security-association pmtu-aging infinite
crypto map crypto_map 1 match address AS3_ACL
crypto map crypto_map 1 set peer 1.1.1.1
crypto map crypto_map 1 set ikev2 ipsec-proposal aes_256
crypto map crypto_map interface outside
crypto ca trustpool policy
crypto ikev2 policy 1
encryption aes-256
integrity sha256
group 2
prf sha256
lifetime seconds 86400
tunnel-group 1.1.1.1 type ipsec-l2l
tunnel-group 1.1.1.1 general-attributes
default-group-policy ipsec_group_policy
tunnel-group 1.1.1.1 ipsec-attributes
ikev2 remote-authentication pre-shared-key *****
ikev2 local-authentication pre-shared-key *****
vpn-idle-timeout 6000
vpn-session-timeout none
vpn-tunnel-protocol ikev2
nat (inside,outside) source static all_inside_networks all_inside_networks destination static all_outside_networks all_outside_networks no-proxy-arp route-lookup
object-group network all_inside_networks
network-object 10.0.1.0 255.255.255.0
object-group network all_outside_networks
network-object 10.0.0.0 255.255.255.0
network-object 10.0.18.0 255.255.255.0
access-list ASA3_ACL extended permit ip object-group all_inside_networks object-group all_outside_networks

Hello

Seems to me that your ASA1 missing certain rules in the 'card crypto' ACL

ASA3_ACL list extended access permitted ip object-group objects ASA3 ASA2-group

ASA2_ACL list extended access permitted ip object-ASA3 group ASA2 object

You miss also the "nat" command I mentioned

public static ASA2 ASA2 destination NAT (outside, outside) static source ASA3 ASA3

You do not have a second order of "nat" because this must match the connection management training is the

Hope this helps

-Jouni

Tags: Cisco Security

Similar Questions

L2l Tunnel upward, without traffic transits

Two 5505 ASA s for the main site of a customer and a local office. I have the tunnel upward. But I am unable to pass traffic through it. I thought I got it, but it turns out I was wrong so I'll let the pros have to him. Thank you!

Main site:

ASA Version 7.2 (4)

!

City of hostname

activate iNbSyJZ1ffmb9kn1 encrypted password

2KFQnbNIdI.2KYOU encrypted passwd

names of

!

interface Vlan1

nameif inside

security-level 100

IP 192.168.100.254 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

IP address 24.x.x.97 255.255.255.248

!

interface Vlan3

prior to interface Vlan1

nameif dmz

security-level 50

no ip address

!

interface Ethernet0/0

switchport access vlan 2

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

passive FTP mode

clock timezone IS - 5

clock to summer time EDT recurring

DNS server-group DefaultDNS

outside_in list extended access permit tcp any host 24.x.x.98 eq 3389

outside_in list extended access permit udp any host 24.x.x.98 eq 1194

outside_in list extended access permit tcp any host 24.x.x.98 eq www

extended vpn 192.168.100.0 ip access list allow 255.255.255.0 192.168.199.0 255.255.255.0

extended vpn 192.168.100.0 ip access list allow 255.255.255.0 192.168.1.0 255.255.255.0

outside_1_cryptomap to access extended list ip 192.168.100.0 allow 255.255.255.0 192.168.1.0 255.255.255.0

pager lines 24

Enable logging

timestamp of the record

exploitation forest-size of the buffer of 100000

recording of debug console

debug logging in buffered memory

asdm of logging of information

Within 1500 MTU

Outside 1500 MTU

MTU 1500 dmz

IP local pool vpnpool 192.168.199.10 - 192.168.199.20

ICMP unreachable rate-limit 1 burst-size 1

ASDM image disk0: / asdm - 524.bin

don't allow no asdm history

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 0-list of access vpn

NAT (inside) 1 192.168.100.0 255.255.255.0

public static 24.x.x.98 (Interior, exterior) 192.168.100.3 netmask 255.255.255.255

Access-group outside_in in external interface

Route outside 0.0.0.0 0.0.0.0 24.x.x.102 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

AAA authentication enable LOCAL console

AAA authentication http LOCAL console

the ssh LOCAL console AAA authentication

Enable http server

http 192.168.100.0 255.255.255.0 inside

http 192.168.100.50 255.255.255.255 inside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

card crypto outside_map 1 match address outside_1_cryptomap

card crypto outside_map 1 set pfs

card crypto outside_map 1 set 24.x.x.54 counterpart

map outside_map 1 set of transformation-ESP-3DES-MD5 crypto

outside_map interface card crypto outside

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

sha hash

Group 2

life 86400

crypto ISAKMP policy 20

preshared authentication

3des encryption

md5 hash

Group 2

life 86400

crypto ISAKMP policy 30

preshared authentication

3des encryption

md5 hash

Group 1

life 86400

Telnet 0.0.0.0 0.0.0.0 inside

Telnet timeout 5

SSH 0.0.0.0 0.0.0.0 inside

SSH 0.0.0.0 0.0.0.0 outdoors

SSH timeout 60

Console timeout 0

attributes of Group Policy DfltGrpPolicy

No banner

WINS server no

DNS server no

DHCP-network-scope no

VPN-access-hour no

VPN - connections 3

VPN-idle-timeout 30

VPN-session-timeout no

VPN-filter no

Protocol-tunnel-VPN IPSec l2tp ipsec webvpn

disable the password-storage

disable the IP-comp

Re-xauth disable

Group-lock no

enable PFS

IPSec-udp disable

IPSec-udp-port 10000

Split-tunnel-policy tunnelall

Split-tunnel-network-list no

by default no

Split-dns no

Disable dhcp Intercept 255.255.255.255

disable secure authentication unit

disable authentication of the user

user-authentication-idle-timeout 30

disable the IP-phone-bypass

disable the leap-bypass

disable the NEM

Dungeon-client-config backup servers

MSIE proxy server no

MSIE-proxy method non - change

Internet Explorer proxy except list - no

Disable Internet Explorer-proxy local-bypass

disable the NAC

NAC-sq-period 300

NAC-reval-period 36000

NAC-by default-acl no

address pools no

enable Smartcard-Removal-disconnect

the firewall client no

rule of access-client-none

WebVPN

url-entry functions

HTML-content-filter none

Home page no

4 Keep-alive-ignore

gzip http-comp

no filter

list of URLS no

value of customization DfltCustomization

port - forward, no

port-forward-name value access to applications

SSO-Server no

value of deny message connection succeeded, but because some criteria have not been met, or because of a specific group policy, you are not allowed to use the VPN features. Contact your administrator for more information

SVC no

SVC Dungeon-Installer installed

SVC keepalive no

generate a new key SVC time no

method to generate a new key of SVC no

client of dpd-interval SVC no

dpd-interval SVC bridge no

deflate compression of SVC

tunnel-group 24.x.x.54 type ipsec-l2l

24.x.x.54 group of tunnel ipsec-attributes

pre-shared-key *.

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the netbios

inspect the rsh

inspect the rtsp

inspect the skinny

inspect esmtp

inspect sqlnet

inspect sunrpc

inspect the tftp

inspect the sip

inspect xdmcp

!

global service-policy global_policy

context of prompt hostname

Cryptochecksum:5180fc35fcb77dbf007b34bc2159c21b

: end

# Sh crypto isa city its

ITS enabled: 1

Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)

Total SA IKE: 1

1 peer IKE: 24.x.x.54

Type: L2L role: initiator

Generate a new key: no State: MM_ACTIVE

# Sh crypto ipsec city its

Interface: outside

Tag crypto map: outside_map, seq num: 1, local addr: 24.x.x.97

outside_1_cryptomap 192.168.100.0 ip access list allow 255.255.255.0 192.168.1.0 255.255.255.0

local ident (addr, mask, prot, port): (192.168.100.0/255.255.255.0/0/0)

Remote ident (addr, mask, prot, port): (192.168.1.0/255.255.255.0/0/0)

current_peer: 24.x.x.54

#pkts program: 56, #pkts encrypt: 56, #pkts digest: 56

#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0

compressed #pkts: 0, unzipped #pkts: 0

#pkts uncompressed: 56, #pkts comp failed: 0, #pkts Dang failed: 0

success #frag before: 0, failures before #frag: 0, #fragments created: 0

Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0

#send errors: 0, #recv errors: 0

local crypto endpt. : 24.x.x.97, remote Start crypto. : 24.x.x.54

Path mtu 1500, fresh ipsec generals 58, media, mtu 1500

current outbound SPI: 16409623

SAS of the esp on arrival:

SPI: 0xFC3F0652 (4231988818)

transform: esp-3des esp-md5-hmac no

running parameters = {L2L, Tunnel, PFS 2 group}

slot: 0, id_conn: 21, crypto-card: outside_map

calendar of his: service life remaining (KB/s) key: (4275000/28514)

Size IV: 8 bytes

support for replay detection: Y

outgoing esp sas:

SPI: 0 x 16409623 (373331491)

transform: esp-3des esp-md5-hmac no

running parameters = {L2L, Tunnel, PFS 2 group}

slot: 0, id_conn: 21, crypto-card: outside_map

calendar of his: service life remaining (KB/s) key: (4274996/28514)

Size IV: 8 bytes

support for replay detection: Y

Remote Desktop:

ASA Version 8.2 (5)

!

water host name

activate rAAeK7vz0gtMeIgU encrypted password

2KFQnbNIdI.2KYOU encrypted passwd

names of

name 192.168.100.0 City City LAN description

DNS-guard

!

interface Ethernet0/0

switchport access vlan 2

!

interface Ethernet0/1

!

interface Ethernet0/2

!

interface Ethernet0/3

!

interface Ethernet0/4

!

interface Ethernet0/5

!

interface Ethernet0/6

!

interface Ethernet0/7

!

interface Vlan1

nameif inside

security-level 100

IP 192.168.1.2 255.255.255.0

!

interface Vlan2

nameif outside

security-level 0

IP address 24.x.x.54 255.255.255.248

!

passive FTP mode

clock timezone IS - 5

clock to summer time EDT recurring

DNS server-group DefaultDNS

outside_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 255.255.255.0 city

inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 255.255.255.0 city

pager lines 24

Enable logging

timestamp of the record

exploitation forest-size of the buffer of 32768

logging asdm-buffer-size 512

Monitor logging notifications

debug logging in buffered memory

logging trap notifications

notifications of logging asdm

Within 1500 MTU

Outside 1500 MTU

IP local pool water 192.168.1.15 - 192.168.1.20 mask 255.255.255.0

ICMP unreachable rate-limit 1 burst-size 1

don't allow no asdm history

ARP timeout 14400

NAT (inside) 0-list of access inside_nat0_outbound

Route outside 0.0.0.0 0.0.0.0 24.x.x.49 1

Timeout xlate 03:00

Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

Floating conn timeout 0:00:00

dynamic-access-policy-registration DfltAccessPolicy

AAA authentication LOCAL telnet console

the ssh LOCAL console AAA authentication

AAA authentication enable LOCAL console

Enable http server

http 192.168.1.0 255.255.255.0 inside

No snmp server location

No snmp Server contact

Server enable SNMP traps snmp authentication linkup, linkdown cold start

Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac

Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac

Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac

Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs

Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

card crypto outside_map 1 match address outside_1_cryptomap

card crypto outside_map 1 set pfs

card crypto outside_map 1 set 24.x.x.97 counterpart

map outside_map 1 set of transformation-ESP-3DES-MD5 crypto

outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

outside_map interface card crypto outside

Crypto ca trustpoint _SmartCallHome_ServerCA

Configure CRL

Crypto ca certificate chain _SmartCallHome_ServerCA

certificate ca 6ecc7aa5a7032009b8cebcf4e952d491

308204 4 a0030201 d 308205ec 0202106e cc7aa5a7 032009b 8 cebcf4e9 52d 49130

010105 05003081 09060355 04061302 55533117 ca310b30 0d 864886f7 0d06092a

30150603 55040 has 13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b

13165665 72695369 676e2054 72757374 204e6574 776f726b 313 has 3038 06035504

0b 133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72

20617574 7a 656420 75736520 6f6e6c79 31453043 06035504 03133c 56 686f7269

65726953 69676e20 436c 6173 73203320 5075626c 69632050 72696 72792043 61 d

65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31

30303230 38303030 3030305a 170d 3230 30323037 32333539 35395a 30 81b5310b

30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20

496e632e 311f301d 06035504 0b 131656 65726953 69676e20 54727573 74204e65

74776f72 6b313b30 5465726d 20757365 20617420 73206f66 39060355 040b 1332

68747470 7777772e 733a2f2f 76657269 7369676e 2e636f6d 2f727061 20286329

302d 0603 55040313 26566572 69536967 61737320 33205365 6e20436c 3130312f

63757265 20536572 76657220 20473330 82012230 0d06092a 864886f7 4341202d

010101 05000382 010f0030 82010 0d has 02 b187841f 82010100 c20c45f5 bcab2597

a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10

9c688b2e 957b899b 13cae234 34c1f35b f3497b62 d188786c 83488174 0253f9bc

7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b

15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845

1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8 63cd

18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced

4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f

81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 01 has 38201 02030100 df308201

082b 0601 05050701 01042830 26302406 082 b 0601 db303406 05050730 01861868

7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1 d 130101

ff040830 02010030 70060355 b 200469 30673065 060, 6086 480186f8 1 d 060101ff

45010717 03305630 2806082b 06010505 07020116 1 c 687474 70733a2f 2f777777

2e766572 69736967 6e2e636f 6d2f6370 73302 has 06 082 b 0601 05050702 02301e1a

1 c 687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406

03551d1f 042d302b 3029 has 027 a0258623 68747470 3a2f2f63 726c2e76 65726973

69676e2e 636f6d2f 2d67352e 70636133 63726c 30 0e060355 1d0f0101 ff040403

02010630 6d06082b 06010505 07010c 59305730 55160969 5da05b30 04 61305fa1

6 d 616765 2f676966 3021301f 2b0e0302 30070605 1a04148f e5d31a86 ac8d8e6b

c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973

69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30

1 b 311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301D 0603

445 1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355 c 1604140d 551d0e04

1 230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300 d 0609 d

2a 864886 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80 f70d0101

4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e

b2227055 d9203340 3307c 265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a

99 c 71928 8705 404167d 1 273aeddc 866d 24f78526 a2bed877 7d494aca 6decd018

481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16

b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0

5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8

6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28

6c2527b9 deb78458 c61f381e a4c4cb66

quit smoking

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

sha hash

Group 2

life 86400

crypto ISAKMP policy 20

preshared authentication

3des encryption

md5 hash

Group 2

life 86400

crypto ISAKMP policy 30

preshared authentication

3des encryption

md5 hash

Group 1

life 86400

No encryption isakmp nat-traversal

Telnet 192.168.1.0 255.255.255.0 inside

Telnet timeout 60

SSH 192.168.1.0 255.255.255.0 inside

SSH timeout 5

Console timeout 0

dhcpd outside auto_config

!

a basic threat threat detection

Statistics-list of access threat detection

no statistical threat detection tcp-interception

WebVPN

attributes of Group Policy DfltGrpPolicy

Group internal water policy

attributes of group water policy

value of 192.168.1.1 DNS server

VPN-idle-timeout no

VPN-session-timeout no

Protocol-tunnel-VPN IPSec

attributes of Registrar username

VPN-group-policy DfltGrpPolicy

type water tunnel-group remote access

water General attributes tunnel-group

water of the pool address

Group Policy - by default-water

DHCP server 192.168.1.1

water ipsec-attributes tunnel-group

pre-shared key *.

tunnel-group 24.x.x.97 type ipsec-l2l

24.x.x.97 group of tunnel ipsec-attributes

pre-shared key *.

!

class-map inspection_default

match default-inspection-traffic

!

!

type of policy-card inspect dns preset_dns_map

parameters

maximum message length automatic of customer

message-length maximum 512

Policy-map global_policy

class inspection_default

inspect the preset_dns_map dns

inspect the ftp

inspect h323 h225

inspect the h323 ras

inspect the rsh

inspect the rtsp

inspect esmtp

inspect sqlnet

inspect the skinny

inspect sunrpc

inspect xdmcp

inspect the sip

inspect the netbios

inspect the tftp

Review the ip options

!

global service-policy global_policy

context of prompt hostname

anonymous reporting remote call

Cryptochecksum:06bda38461d2419b3e5c4904333b62e7

: end

# sh crypto isa water his

ITS enabled: 1

Generate a new key SA: 0 (a tunnel report Active 1 and 1 to generate a new key during the generate a new key)

Total SA IKE: 1

1 peer IKE: 24.x.x.97

Type: L2L role: answering machine

Generate a new key: no State: MM_ACTIVE

water # sh crypto ipsec his

Interface: outside

Tag crypto map: outside_map, seq num: 1, local addr: 24.x.x.54

outside_1_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.100.0 255.255.255.0

local ident (addr, mask, prot, port): (192.168.1.0/255.255.255.0/0/0)

Remote ident (addr, mask, prot, port): (Town/255.255.255.0/0/0)

current_peer: 24.x.x.97

#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0

#pkts decaps: 78, #pkts decrypt: 78, #pkts check: 78

compressed #pkts: 0, unzipped #pkts: 0

#pkts uncompressed: 0, comp #pkts failed: 0, #pkts Dang failed: 0

success #frag before: 0, failures before #frag: 0, #fragments created: 0

Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0

#send errors: 0, #recv errors: 0

local crypto endpt. : 24.x.x.54, remote Start crypto. : 24.x.x.97

Path mtu 1500, fresh ipsec generals 58, media, mtu 1500

current outbound SPI: FC3F0652

current inbound SPI: 16409623

SAS of the esp on arrival:

SPI: 0 x 16409623 (373331491)

transform: esp-3des esp-md5-hmac no compression

running parameters = {L2L, Tunnel, PFS 2 group}

slot: 0, id_conn: 126976, crypto-card: outside_map

calendar of his: service life remaining (KB/s) key: (3914995/28408)

Size IV: 8 bytes

support for replay detection: Y

Anti-replay bitmap:

0xFFFFFFFF to 0xFFFFFFFF

outgoing esp sas:

SPI: 0xFC3F0652 (4231988818)

transform: esp-3des esp-md5-hmac no compression

running parameters = {L2L, Tunnel, PFS 2 group}

slot: 0, id_conn: 126976, crypto-card: outside_map

calendar of his: service life remaining (KB/s) key: (3915000/28408)

Size IV: 8 bytes

support for replay detection: Y

Anti-replay bitmap:

0x00000000 0x00000001

Thanks again!

In addition,

Now that I actually think...

The original ICMP you did would go as follows
- 192.168.100.x send ICMP messages to echo
- Happens on ASA local
- Gets sent through the VPN L2L connection
- Arrives on the ASA remote
- ASA forwards traffic on the LAN Host 192.168.1.x
- LAN forward host to respond to its default gateway 192.168.1.1 (NOT ASA)
- ICMP Echo traffic gets lost because of no real route for the return traffic
  - Therefore, you see no encapsulated traffic to destination, ASA, decapsules only traffic that origin of the host that sends the ICMP messages to echo through the VPN L2L
-Jouni

L2l AAS behind router

Can an ASA initiate a VPN L2L on NAT - T behind a router?

The VPN can be established successfully, when our third party start the connection, but not when we leave it to our end.

Many providers do not support this scenario, I would like to know if Cisco do.

Yes it will work. The SAA can be behind a NAT as an originater IPSec as an IPSec responder. Of course As NAT is configured correctly if the ASA's answering machine.

--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni

Impossible to route traffic through a tunnel "will" in a frame relay Center and spoke environment.

Hello

I have a network star frames environment.

Headquarters (hub) and around seven remote branch offices.

I'm trying to encrypt all data between the hub-and-spoke is borrowing point gre tunnels to point of the hub-spoke.

I made the necessary set up on all routers and using SDM and all tunnels appeared.

The problem when I tried to redirect all traffic to the respective subnet through the tunnel s assigned

nothing is happen.

I decided to do a bit of troubleshooting with a radius of one and test the connection to the hub.

Ping from Headquarters to the tunnel endpoint

Router01 #ping ppp.168.140.14

Type to abort escape sequence.

Send 5, echoes ICMP 100 bytes to ppp.168.140.14, wait time is 2 seconds:

.....

Success rate is 0% (0/5)

Ping of speaks to the tunnel endpoint

router04 #ping ppp.168.140.4

Send 5, echoes ICMP 100 bytes to ppp.168.140.4, wait time is 2 seconds:

.....

See nearby networking is learned by talking about following the eigrp process

router04 #sh ip eigrp not

Neighbors of the EIGRP intellectual property to process 10

H address Interface Hold Uptime SRTT RTO Q Seq

(s) (ms) NTC Num

14 40 2280 0 2493678 2d21h Se0/0/0.1 0 10.x.x.1

See nearby networking learned by Hub following the eigrp process

H address Interface Hold Uptime SRTT RTO Q Seq

(s) (ms) NTC Num

8 ppp.168.160.16 Tu2 31 00:00:26 1 5000 1 0

7 ppp.168.150.15 Tu1 13 00:00:47 1 5000 1 0

3 ppp.168.170.17 Tu3 14 00:00:59 1 5000 1 0

2 ppp.192.168.190.19 Tu4 13 00:01:05 1 5000 1 0

0 ppp.168.140.14 Tu0 31 00:01:18 1 5000 1 0

11 10.x.0.6 Se0/0/0.4 12 02:40:20 53 318 0 399684

1 10.x.x.9 Se0/0/0.7 11 02:41:20 1380 5000 0 377427

9 10.x.x.5 Se0/0/0.3 11 02:44:28 47 1426 0 370651

4 10.x.x.7 Se0/0/0.5 12 51 306 0 363006 1d23h

5 10.x.x.8 Se0/0/0.1 12 77 462 0 1210492 2d06h

12 11 51 306 0 395295 2d21h Se0/0/0.8 10.x.x.11

6 10.x.x.4 Se0/0/0.2 14 53 318 0 284379 2d21h

Router01 #.

I have a closed configurations of the hub and one of the RADIUS (the problem as outline above that happens for all the rays).

There is also the pre-shared keys were Strip and IP set up for security reasons.

Concerning

Jomo

Sure no problem.

Have a good holiday.

ASA - Tunnel all traffic, allow rays to communicate with each other

Well, I hope someone can help me with this headache! Switching to employ a PIX and VPN 3005 concentrator Office at home in an ASA5510 for firewall and IPSEC tunnels. It is pretty much a
- VPN on a stick, multiple rays.
- All traffic sent by tunnel
- Internet access through main office (using the web filter) of
- VOIP to VOIP between rays
- All departments are using the clients VPN 3005 HW or ASA 5505 s
HEADQUARTERS: 10.0.0.0/24

Speaks 1: 192.168.11.0 / 24

Speaks 2: 192.168.12.0 / 24

Speaks 3: 192.168.13.0 / 24

-continues to 192.168.31.0 / 24

Spoke with the current configuration, 1 can communicate with all the resources in the home, office and Internet integrated properly checked by a tracert. However, the rays cannot communicate with each other. This is required for VOIP traffic, when all TALK TALK calls are made (sites).

Logging information when talk of talks initiated icmp:
- No group of translation found for icmp src, dst outside: 192.168.31.1 inside: 192.168.11.1 (type 8, code 0)
If I remove the nat (outside) 1 192.168.0.0 255.255.00 - rays will begin to respond to each other, but then the rays cannot tunnel through the Home Office Internet traffic. My brain is so scrambled after the cramming of VPN configurations for these days, so I hope someone has an idea. I've always used concentrators 3005, so it's a little different! In the search for documentation for this configuration, I was surprised that this isn't a most common topology. It seems that this article would (http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00805734ae.shtml), but there is no rays! In any case, I'm sure this has something to do with NAT rules and perhaps who need access for traffic list speaks of talking.

=============================================

ASA Version 8.2 (1)
!
hostname asa5510

interface Ethernet0/0
Speed 100
full duplex
nameif outside
security-level 0
IP address 97.65.x.x 255.255.255.224

interface Ethernet0/1
Speed 100
full duplex
nameif inside
security-level 100
IP 10.0.0.40 255.255.0.0

permit same-security-traffic inter-interface

permit same-security-traffic intra-interface

the DM_INLINE_NETWORK_1 object-group network
object-network 10.0.0.0 255.255.0.0

object-network 192.168.0.0 255.255.0.0

access-list sheep extended ip 10.0.0.0 allow 255.255.0.0 192.168.0.0 255.255.0.0

Allow Access-list extended wccp servers ip host 10.0.0.83 a

Redirect traffic extended access-list deny ip any object-group DM_INLINE_NETWORK_1

Redirect traffic scope permitted any one ip access-list

Global 1 interface (outside)
NAT (outside) 1 192.168.0.0 255.255.0.0
NAT (inside) 0 access-list sheep
NAT (inside) 1 10.0.0.0 255.255.0.0

Route outside 0.0.0.0 0.0.0.0 97.65.x.x 1
Route inside 192.168.0.0 255.255.255.0 10.0.0.1 1
Route inside 192.168.2.0 255.255.255.0 10.0.0.1 1
Route inside 192.168.3.0 255.255.255.0 10.0.0.1 1

Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto ipsec df - bit clear-df outdoors

Crypto-map dynamic dynmap 1 transform-set RIGHT

map mymap 65535-isakmp ipsec crypto dynamic dynmap

mymap outside crypto map interface

crypto isakmp identity address

crypto ISAKMP allow outside

crypto ISAKMP policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400

crypto ISAKMP policy 10
preshared authentication
3des encryption
md5 hash
Group 2
life 86400

crypto ISAKMP ipsec-over-tcp port 10000

management-access inside

a basic threat threat detection

no statistical access list - a threat detection
no statistical threat detection tcp-interception

WCCP web cache redirect-list Redirect-traffic group-list password xxxxxxx wccp-servers
WCCP 90 redirect-list traffic Redirect wccp servers group-list password xxxxxxx

WebVPN

internal MJHIvpn group strategy

attributes of Group Policy MJHIvpn
value of server WINS 10.0.10.1 10.0.10.2
value of 10.0.10.1 DNS server 10.0.10.2
allow password-storage
Split-tunnel-policy tunnelall
mjhi.local value by default-field
allow to NEM

username field-3002 SjfS1Pq2xZGxHicx encrypted password

attributes of username field-3002
VPN-access-hour no
VPN - 250 simultaneous connections
VPN-idle-timeout no
VPN-session-timeout no
Protocol-tunnel-VPN IPSec
allow password-storage
type of remote access service

remote access to field tunnel-group type

General-field tunnel-group attributes
Group Policy - by default-MJHIvpn

IPSec-attributes of tunnel-group field
pre-shared-key *.

class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
inspect the they
inspect the icmp
!
global service-policy global_policy

Hello Ala,

In Act got to be with the Nat configuration.

So basically you want to tunnel the traffic on the rays to communicate with each other.

OK, it would be with a nat 0 with the access list with the corresponding traffic outside.

Also on the crypto ACL for each site configuration, you must add an entry for the traffic of other offices.

I hope that I have explained myself.

Have a good

Julio

Note all useful posts!

Traffic generated by router IOS inspect IPv6

I try to configure the IPv6 packets on a router 2911 deep inspection (IOS 15.1 (2) T5) but I'm not able to inspect the traffic generated by router. It is not an option "ipv6 inspect name xxxx udp router-traffic' as in IPv4. So I am unable to ping to the router to a remote host.

I could solve the problem of ping by simply adding a "permit any any icmp echo response" on my ACL, but I still can't access TCP or UDP based services (DNS, HTTP,...).

Anyone knows if it is possible to activate the traffic generated by IPv6 router, or is there another solution for this problem? If so, how can I do that?

Partial configuration:
```
ipv6 unicast-routing

ipv6 inspect name SPI_DIALER1_OUT tcpipv6 inspect name SPI_DIALER1_OUT udpipv6 inspect name SPI_DIALER1_OUT icmpipv6 inspect name SPI_DIALER1_OUT ftp
```
```
interface Dialer1 ipv6 inspect SPI_DIALER1_OUT out ipv6 traffic-filter acl6_dialer1_in in
```
```
ipv6 access-list acl6_dialer1_in sequence 10 permit icmp any any nd-ns sequence 20 permit icmp any any nd-na sequence 30 permit icmp any any router-advertisement sequence 40 permit icmp any any echo-reply deny ipv6 any any log
```
Former Cisco's IOS 'inspect' system has indeed been deprecated. You should use zone based firewall now.

Here is the guide for the care of the IPv6 zone based firewall.

http://www.Cisco.com/c/en/us/TD/docs/iOS-XML/iOS/sec_data_zbf/configuration/XE-3s/sec-data-ZBF-XE-book/sec-ZBF-IPv6.html

If you want to go at a faster speed for the area based ipv4 firewall, try to use my Config Wizard and copy the bits you need.

http://www.IFM.NET.nz/cookbooks/890-ISR-Wizard.html

Routing of traffic for a specific user through vpn Ipsec

I want to route traffic to a specific host on the internet through our external interface (for example, 7.7.7.0/27) instead of the internet connection of the client (for example 9.9.9.9).

I have already added 9.9.9.9 in the split dns acl so that the road is inserted on the client workstation and a default route on the external interface is defined as follows:

CISCOASA # run HS | I have the route outside

Route outside 0.0.0.0 0.0.0.0 7.7.7.30 1

Nat config

object obj-InsideNetworks network

NAT 7.7.7.3 Dynamics (indoor, outdoor)

No nat

NAT (inside, all) source static obj-InsideNetworks obj-InsideNetworks destination DEST-Interior-SHEEP inside-DEST-SHEEP no-proxy-arp static

object obj-InsideNetworks network

range 10.0.1.0 10.0.255.255

object-group network inside-DEST-SHEEP

network-object 10.0.3.0 255.255.255.0

object-network 10.0.2.0 255.255.255.0

object-network 10.10.10.0 255.255.255.0

object-network 10.0.4.0 255.255.255.128

The static IP assigned to the vpn client is 10.0.4.150 if it is not the scope of the Interior-DEST-SHEEP. If again I traceroute

9.9.9.9 when connected, I get the first bond 7.7.7.1 and it stops there.

Would appreciate any help on this.

Hello

If you try to NAT the VPN user traffic when it connects to the Internet through the ASA NAT configuration so that the user should then be

network of the VPN-CLIENT-PAT object

subnet 10.0.4.128 255.255.255.128

dynamics of NAT (outdoors, outdoor)

Insert the dynamic PAT public IP in the above configuration. You can either use "interface" parameter to use the public IP address of ASAs or insert a detached public IP address that can be used. I guess the Pool of VPN uses the 10.0.4.128/25 subnet.

You must also make sure you have the following configuration enabled

permit same-security-traffic intra-interface

You can check with

See the race same-security-traffic

Note that there is another similar parameter that ends in "inter-interface" who used to work for this situation.

Hope this helps

Let me know if make you it work

-Jouni

IPSec site to site VPN cisco VPN client routing problem and

Hello

I'm really stuck with the configuration of ipsec site to site vpn (hub to spoke, multiple rays) with cisco vpn remote client access to this vpn.

The problem is with remote access - cisco vpn client access - I can communicate with hub lan - but I need also communication of all lans speaks of the cisco vpn client.

There are on the shelves, there is no material used cisco - routers DLINK.

Someone told me that it is possible to use NAT to translate remote access IP-lan-HUB customers and thus allow communication - but I'm unable to set up and operate.

Can someone help me please?

Thank you

Peter

RAYS - not cisco devices / another provider

Cisco 1841 HSEC HUB:

crypto ISAKMP policy 1

BA 3des

preshared authentication

Group 2

ISAKMP crypto key x xx address no.-xauth

!

the group x crypto isakmp client configuration

x key

pool vpnclientpool

ACL 190

include-local-lan

!

86400 seconds, duration of life crypto ipsec security association

Crypto ipsec transform-set esp-3des esp-sha-hmac 1cisco

!

Crypto-map dynamic dynmap 10

Set transform-set 1cisco

!

card crypto ETH0 client authentication list userauthen

card crypto isakmp authorization list groupauthor ETH0

client configuration address card crypto ETH0 answer

ETH0 1 ipsec-isakmp crypto map

set peer x

Set transform-set 1cisco

PFS group2 Set

match address 180

card ETH0 10-isakmp ipsec crypto dynamic dynmap

!

!

interface FastEthernet0/1

Description $ES_WAN$

card crypto ETH0

!

IP local pool vpnclientpool 192.168.200.100 192.168.200.150

!

!

overload of IP nat inside source list LOCAL interface FastEthernet0/1

!

IP access-list extended LOCAL

deny ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

deny ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

IP 192.168.7.0 allow 0.0.0.255 any

!

access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

!

How the DLINK has been configured for traffic between the site to site VPN subnets? You are able to add multiple remote subnets on DLINK? If you can, then you must add the pool of Client VPN subnet.

Alternatively, if you cannot add multiple subnet on DLINK router, you can change the pool of Client VPN 192.168.6.0/24, and on the crypto ACL between the site to site VPN, you must edit the 180 existing ACL

DE:

access-list 180 allow ip 192.168.7.0 0.0.0.255 192.168.1.0 0.0.0.255

access-list 180 allow ip 192.168.200.0 0.0.0.255 192.168.1.0 0.0.0.255

TO:

access-list 180 allow ip 192.168.6.0 0.0.1.255 192.168.1.0 0.0.0.255

Also change the ACL 190 split tunnel:

DE:

access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.200.0 0.0.0.255

access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.200.0 0.0.0.255

TO:

access-list 190 allow ip 192.168.7.0 0.0.0.255 192.168.6.0 0.0.0.255

access-list 190 allow ip 192.168.1.0 0.0.0.255 192.168.6.0 0.0.0.255

Finally, replace the remote subnet 192.168.7.0/255.255.255.0 192.168.6.0/255.255.254.0 DLINK.

Hope that helps.

Modem or router?

I know this will seem like a dumb question, but please explain the difference between a modem and a router, and when you use one over the other?

A Modem is a device to connect to a network of service providers, while a router is used to share this connection social network ISP among devices on a subnet or LAN. Thus, for example, number of connections DSL or cable home, will have a modem service provider that connects to the outside world, negotiates and manages all traffic between the world and your home. And you have a router (or wifi router) now allow multiple devices on your home network to share this worldly internet connection provided by the modem connection to your ISP gateway (it literally routes traffic between your devices and the tube of the modem to the Internet). Nowadays many features combines a modem and a router in one device.

Problem WCCP or routing

Hello

We have two centres of data logical LAN even.

Two routers ISP and two WAE 674 and the help of WCCP "evacuation-method negotiated return of interception-method wccp.

See the attached file.

The problem is when one of the interface WAN 'line' falls down, some of the network is not accessible from the side LAN and some.

We use BGP as routing protocol in the ISP routers.

Any suggestion for the problem?

Jan

Hi Jan,

What is suspect here is the WCCP.

When you configure, it allocates buckets if you use hash assignment. If you use a mask, it calculates the mask according to your destination / source ip address.

Now, what I understand is - if WAN fails, some networks is not accessible.

When LAN goes down, WCCP breaks down and starts running smooth.

A few questions:

1. what happens if LAN drops but WAN remains upward? WCCP remains active state / usable?

2 when WAN breaks down and the remains of the LAN upward, your WCCP is still in PLACE and so it continues to transmit packets of same WAN interface but because this interface is down, the packages ultimately die / gets blackholed.

3 another speculation is: asymmetric routing. When WAN is down but LAN is in place, you transfer a portion of the traffic off LAN but as WAN falls down, return packets can arrive on a different interface and creates an asymmetric routing.

To reduce this problem, please enter interface in three stages:

1 WAN - LAN - UP, down, is accessible from router ID?

2. IN WAN, LAN - down, is accessible router ID?

3. WAN downwards, towards the low LAN, is the accessible router ID?

CLI to capture logs:

2. show ip wccp
3 view the details of interface ip wccp
4 show ip wccp service
5 show ip wccp details
6. specify ip wccp internal (*)
7 show running-config
8 show ip wccp hash<61 62="">
9 sh wccp mask tcp-promised
10 HS tech

In addition, as you use GRE encapsulation for redirection of WCCP, the router uses the router address IP ID as its IP source address. The router ID IP address is the loopback address higher on the router, or if the loopback interface is not configured, the router ID IP address is the highest address of the physical interfaces. The router address IP ID is used as the source address for redirected packets from the router to the Cisco WAE and accordingly, it is also used as a destination address for the Cisco WAE to the router traffic, therefore, you must be sure that a route is defined between the router Cisco WAE. This is done by configuring a static route on the Cisco WAE to address IP router ID. The router ID can be identified with wccp routers see command on the Cisco WAE.

As in your case, you have multiple routers, a static route must be added to each router IDs. These router command to configure static routes is:

WAE (config) # ip route

Can you please try above and let us know if it works?

Kind regards.

VPN router to the problem of the ASA

Hello world.

I am doing a VPN between a router and a series of ASA5500 and difficulties.

The router part is 100% correct because it is a daily task, but miss me something on the side of the ASA of the things.

The ASA also has remote via IPsec tunnels clients as you'll see below, so I have to make sure that continues to work!

It is a fairly urgent question. So any help or advice can be provided, it would be very appreciated!

Here is the router part:

!

crypto ISAKMP policy 1

BA 3des

preshared authentication

Group 2

isakmp encryption key * ASA-PUBLIC-IP address

ISAKMP crypto keepalive 100

!

!

Crypto ipsec transform-set transform-set esp-3des esp-md5-hmac

!

10 customers map ipsec-isakmp crypto

defined ASA-PUBLIC-IP peer

transform-set transform-Set

match address 102

QoS before filing

!

!

Access-list 100 remark [== NAT control ==]

access-list 100 deny ip 192.168.2.0 0.0.0.255 10.1.1.0 0.0.0.255

access-list 100 permit ip 192.168.2.0 0.0.0.255 any

Access-list 102 remark == [VPN access LISTS] ==

access-list 102 permit ip 192.168.2.0 0.0.0.255 10.1.1.0 0.0.0.255

Access-list 102 remark

(Crypto card has been applied to the corresponding interface)

SIDE OF THE ASA:

permit inside_nat0_outbound to access extended list ip 10.1.1.0 255.255.255.0 10.1.1.192 255.255.255.224

prevpn_splitTunnelAcl list standard access allowed 10.1.1.0 255.255.255.0

access-list Interior-access-in extended permit ip 10.1.1.0 255.255.255.0 any

access-list Interior-access-in extended permit icmp 10.1.1.0 255.255.255.0 any

access list for distance-extended permitted ip network 10.1.1.0 255.255.255.0 192.168.2.0 255.255.255.0

Global (outside) 1 ASA-PUBLIC-IP

NAT (inside) 0-list of access inside_nat0_outbound

NAT (inside) 1 10.1.1.0 255.255.255.0

NAT (inside) 0 192.168.2.0 255.255.255.0

Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac

Crypto-map dynamic outside_dyn_map 20 the transform-set ESP-3DES-MD5 value

card crypto outside_map 40 match remote-network address

card crypto outside_map 40 game peers REMOTE-router-IP

outside_map card crypto 40 the transform-set ESP-3DES-MD5 value

map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map

outside_map interface card crypto outside

ISAKMP allows outside

part of pre authentication ISAKMP policy 10

ISAKMP policy 10 3des encryption

ISAKMP policy 10 md5 hash

10 2 ISAKMP policy group

ISAKMP life duration strategy 10 86400

tunnel-group prevpn type ipsec-ra

tunnel-group prevpn General-attributes

address pool VPN-pool

Group Policy - by default-prevpn

prevpn group of tunnel ipsec-attributes

pre-shared-key *.

tunnel-group REMOTE-router-IP type ipsec-l2l

REMOTE-router-IP tunnel-group ipsec-attributes

pre-shared-key *.

Hi Chris

first on the router make this change to littil than u ned to add md5 as hashing whil employees u th in the asa and the router u did not, so the default is sha!

do

crypto ISAKMP policy 1

md5 hash

now on the SAA as I see that there is a problem in nat0 you line l2l tunnel

so that you need to look like:

permit inside_nat0_outbound to access extended list ip 10.1.1.0 255.255.255.0 192.168.2.0 255.255.255.0

You also need a permit for the ipsec traffic, the following command will allow all ipsec traffic if you want to filter traffic not to use this command and use rather ACLs on the external interface, but following that to allow all traffic to your L2L and remote vpn access:

Permitted connection ipsec sysopt

so, please:

clear xlate and reload the ASA then attempt to leave the expmtion NAT new effects

Good luck

If useful rates

Multiple virtual private networks - one Interface

Hello

I read up on top of the site to create using IPSEC VPN. My question is, if I have a router dedictaed "VPN" in the same place, say the external interface is F0/0. I want to configure different VPN for this site to some remote sites using this router, but I want to be able to each of these VPN connections have got it of own interface, fo the goal, routing some subnets over a VPN connection and routing another subnet on the other VPN sites.

So Hub site, I have an outside interface, but need IPSEC VPN multi-site spoke and each site to have an interface I can route traffic through... If that makes sense?

Thank you

I fear that your post, as written makes no sense to me. You start by saying you have a router with an outside interface. Then, you say that you need more than one interface. On the surface that seems to indicate you need to get a different router which will have several available for VPN interfaces.

Maybe if stress you less the need for multiple interfaces and explain a bit more about what you really need that it would be a way to accomplish what you need with the existing router.

I'll start with what seems to indicate that with an interface of the router would have a card encryption. But a card encryption can have multiple instances of cryptographic definitions it contains with a single instance for each remote peer. So, for example, you could have crypto match GRANT_map 10 of peers A and GRANT_map 20 for homologous B and 30 GRANT_map for C counterpart. Within each instance of the encryption card you would identify a single access list to identify traffic to destination each peer. It might look like this:

map GRANT_map 10 ipsec-isakmp crypto

dieudo game address

defined peer 1.2.3.4

map GRANT_map 20 ipsec-isakmp crypto

match the address peerB

defined by the 5.6.7.8 peers

map GRANT_map 30 ipsec-isakmp crypto

match the address peerC

defined by peer 9.10.11.12

Dieudo extended IP access list

ip licensing 10.1.1.0 0.0.0.255 172.16.0.0 0.0.255.255

peerB extended IP access list

ip licensing 10.2.2.0 0.0.0.255 172.17.0.0 0.0.255.255

peerC extended IP access list

IP 10.3.3.0 allow 0.0.0.255 172.18.0.0 0.0.255.255

Or maybe you can consider using the GRE with IPSec VPN tunnels. You can configure several tunnels, each source just outside of the interface, and each of them would end on a different peer. You can send some 10 to Dieudo tunnel subnets and route to other subnets of tunnel 20-peerB and route to other subnets of tunnel 30-peerC. This kind of solution might meet your requirements.

HTH

Rick

VMotion traffic isolation, vlan trunking

We have 2 full length M910 blade servers sitting in the dell blade enclosure. Installed esxi 5.0 on the two blades and joined them to the cluster.
Each server blade full length a 8 network cards. 2 ports double aboard the card NETWORK and 2-port Ethernet mezzanine card. All are connected to the internal cisco switch 3130 installed on the module e/s A1, A2, B1 and B2. all the internal switches are stacked together by the network team. and there is a link to internal switch (uplink) and an external switch (ports) that are on the vlan 137
All the ports that are connected to the esxi host are configured as trunk on the switches of internal physical cisco blade by the network team. in our total case 16 ports (8 cards x 2 servers) are fixed to the internal trunk on cisco switch and there is internal cisco switch uplink and our external switch (located on vlan 137)
On esxi5.0, we set up a big flat switch affecting all physical network cards to Vswitch 0.
Please refer page for groups of ports configured.

To isolate the vmotion traffic, we have configured tag (150) vlan different for vmotion. but vmotion does not work. Unable to ping of vmotion ips with each other. But if I change brand VLAN to 137. vmkping works on the other and work of vmotion.
If I change brand VLAN other than 137 to any group of ports (for example, management or virtual machine), I'm losing connection to the corresponding port group.

I think that missing configure something on the blade switches internal cisco (3130). Please advise on what needs to be configured. I know that kind of why trunking is required. If you could explain the exact purpose of why the necessary circuits for esx would be great.
What is advised to configure a virtual switch, such as a large flat switch or multiple switches
Assigning to each switch port group. recommended configuration to enable balancing the increased load of incoming and outgoing and fail over. detailed explanation would be really useful for non admins networks

I will try to describe one of the possible configurations.

First some facts/support:
- 2 ESXi hosts
- 4 blade switches
- 1 external switch
- 8 NICs in each server Blade (2 NICs for each of the switches)
- vmnic0 and vmnic4 are connected to two different switches
- different subnets / VLAN for vMotion (100), management (101) and VM networks (102,...)
- all VLANS represent them different IP subnets
Virtual network configuration:
- 2 vSwitches: 1 for management, 1 for VM networks and vMotion
- vSwitch0 for management and vMotion (vmnic0 + vmnic4)
  --> Management ports (VLAN 101) Group: vmnic0 (active), vmnic4 (at rest)
  -> vMotion Port Group: (VLAN 100): vmnic4 (active), vmnic0 (at rest)
- vSwitch1: VM networks (vmnic1.. 3 + vmnic5...) 7)
  -> VM 1 (VLAN 101) port group
  -> Port VM 2 (VLAN 102) group
  -> ...
Blade switches:
- all the VLANS configured in the virtual network are present
- all ports of downlink to the ESXi hosts are configured to trunk mode, all the VLANS allowed
- at least 2 uplinks and the external switch configured as a trunk, EtherChannel (LACP)
- ports of rising and descending liaison (on each of the switches) are a group of track link state
External switch:
- all the VLANS configured in the virtual network are present
- four channels of Port/EtherChannels (LACP), one to each switch blade
You can configure the VLANS on switches separately or by VTP. In any case, all the VLANS should be present on the switches of. If you need to route traffic between some VLANs, you must either set up a router on your network, or - in the case where the switches support and are properly authorized - configure routing ip (Inter VLAN routing).

André

HP8600: Wireless router connection

I installed a new router to my DSL network connection. I configured my HP8600 printer to my new router but I still can't get my nto computer communicate with my printer.

The simplest answer is to restart the computer Windows 8.1. This will help if the problem is an entry port stale in the process of discovery of Windows.

If the problem is more than that, you can try one of the following solutions.

1. make sure the printer and the computer are on the same wireless network. The new router can have several wireless networks and the router can now to route traffic feel between them.

2. set up an IP address manually on the printer and the configuration of Windows printer as follows:

- Define printers by the built-in Web server IP address (video link)

-Follow these instructions for the user ShlomiL to change the printer port configuration Windows 8.1

Update of the intellectual property of the HP software for one of your PCs. software click the utilities tab, then update the IP address, type the current address and save the changes.

Finally, on your PC of Windows 8 open the control panel and select devices and printers.

Right-click on the printer and select printer properties.

On the Ports tab, create a new port by selecting Standard TCP/IP.

Follow the screen by using the IP address and save the changes by keeping the Standard TCP/IP port.

Problem with router SPA2102 Battlefield 2?

I have problems with my Battlefield 2 (all versions). I have the SPA2102.

EDIT: The game freezes when I click to join a server, nothing happens.

I can play other games online.

When I try the demo version which im using this router, it does not work.

But when I try with the same laptop in other places it works completely fine.

I set up a static IP address and forwarded my ports to help

http://www.PortForward.com/English/routers/port_forwarding/Linksys/Spa-2102/Battlefield_2.htm

What else can I do to make it work?

I am running Vista 32 bit.

Thank you in advance!

Basically the SPA2102 is not design to handle the heavy traffic. This unit is designed to route traffic for VOIP devices and not for game features.

L2l multiple rays routing traffic

Similar Questions

Maybe you are looking for