L2TP between router (BIN) and CVPN3000 (LNS)

Similar Questions

• Difference between routing tables and publish

  Hello
  
  My understanding of a Routing Table and the Table to publish is:
  
  Routing table: it is used to select the different routes for a service based on the results of an XQuery expression in a stream of messages.
  
  Table to publish: it is used to select the service target according to the results of an XQuery Expression.
  
  The two seem to work quite similar, but I guess that in the option table to publish the service for a branch is called asynchronously.
  
  Is this good? There is another difference between the two options?
  
  Any help would be greatly appreciated.
  
  Thank you
  Priya.

  Re: compare routing action against action Service legend against action to publish?

  Same differences between publish and route should be applicable for the table in the publication and the routing table.

• NAT via LAN-to-LAN configuration between router IOS and Cisco VPN 3000

  Hello

  I have the following document on the creation of a virtual LAN2LAN including NAT private network.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2284/products_configuration_example09186a00801ae24c.shtml

  It? s easily do this with the hub. Now, I have to set it up on the IOS router, and for this purpose, I can? t find any information. NAT, I have my private network to a single IP address that must be by tunnel as my local network official.

  Anyone have documentation on this szenario? I can? t is not on the OCC.

  Thanks for the support

  Hello.

  Concentrators are very friendly units (IMHO) to VPN with NAT and VPN.

  You build an acl defined traffic over the vpn (110) based on the nat wouldn't

  You create an acl to set what is NAT had (111) and create a NAT statement accordingly

  Here is an example configuration.

  !

  crypto ISAKMP policy 10

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  vpnsrock crypto isakmp key! address x.x.x.x

  !

  !

  Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac

  !

  10 VPN ipsec-isakmp crypto map

  defined peer x.x.x.x

  game of transformation-ESP-3DES-SHA

  match address 110

  !

  interface Fa0

  NAT outside IP

  VPN crypto card

  !

  !

  interface fa1

  IP nat inside

  !

  IP nat inside source list 111 interface fa0 overload

  IP route 0.0.0.0 0.0.0.0 y.y.y.y

  access-list 110 permit ip fa0 - ip network-remote control-generic generic-mask

  access-list 111 allow local-network ip network-remote control-generic generic-mask

  !

• tunnel from site to site between router IOS and ASA

  I've combed through the configs on both sides of this tunnel 4 x now and the look of policies as they match. I applied the http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a0080094498.shtml note

  My crypto lsits access are good and my nat on the side of IOS are provided with a map of the route and look good. On the SAA traffic side on the side of the remote tunnel ASA is exempt from NAT. Each side already has a site to another tunnel configuration, so I added the appropriate lines to the existing cryptographic cards which include peers, transform set and match address 'access-list. The polcies crypto isakmp on both ends are compatible. I have attached some configs and debugs (from router IOS), but essentially the newspaper on the SAA starts with the phase 1 is complete and then routing not received notification message, no proposal chosen readings and then it goes to IKE lost the connection to a remote peer, connection, drop table correlator counterpart has failed, no match, the deletion and finally disconnected session reason lost service.

  Their other tunnel stay standing as well as the configuration of remote access vpn connection is good.

  I found a note that recommends checking any access security-list, so I removed the, but no luck, and a Cisco associated with a hub, but had a healthy logic

  Is displayed normally with the

  Cisco VPN 3000 correspondent

  message hub: no proposal

  Chosen (14). This is a result of the

  being host-to-host connections.

  The configuration of the router has the

  IPSec proposals ordered so that the

  proposal selected for the router

  with the access list, but not the

  peer. The access list has a larger

  network including the host that

  a cutting traffic.

  Make the router for this proposal

  hub to router connection

  first in line, so that it corresponds to the

  specific to the host first.

  but that didn't work either.

  Thank you

  Bill

  Bill,

  Take a look at this

  000610: * PCTime 10:42:15.094 Sep 27: ISAKMP: (2039): need XAUTH

  000611: * 10:42:15.094 PCTime sep 27: ISAKMP: node set 920927400 to CONF_XAUTH

  000612: * 27 sep 10:42:15.094 PCTime: ISAKMP/xauth: application XAUTH_USER_NAME_V2 attribute

  000613: * 27 sep 10:42:15.094 PCTime: ISAKMP/xauth: application XAUTH_USER_PASSWORD_V2 attribute

  000614: * 27 sep 10:42:15.094 PCTime: ISAKMP: (2039): launch peer 74.92.97.166 config. ID = 920927400

  000615: * 27 sep 10:42:15.094 PCTime: ISAKMP: (2039): lot of 74.92.97.166 sending peer_port my_port 4500 4500 (R) CONF_XAUTH

  -Other - 000616: * PCTime 10:42:15.094 Sep 27: ISAKMP: (2039): entry = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE

  000617: * PCTime 10:42:15.094 Sep 27: ISAKMP: (2039): former State = new State IKE_P1_COMPLETE = IKE_XAUTH_REQ_SENT

  It should not go to extend the authentication. Since you have the client and the L2L on the same router and clients are configured for Extended authentication, the router will ask for XAUTH unless you configure the "No.-xauth" command after the pre-shared key

  Please implement the command:

  ISAKMP crypto keys in clear text address 74.92.97.166 No.-xauth

  Thank you

  Gilbert

• PPTP VPN between clients Windows and Cisco 2921 router

  Hi all!

  I have a problem with PPTP VPN between Windows clients and router Cisco 2921 with permission of RADIUS (IAS). When I try to connect to Cisco 2921 of Windows 7 by using MS-CHAP v2 I get the message 778: it was not possible to verify the identity of the server. Can I use PAP - power is OK. On Windows XP, the same situation.

  Cisco config:

  version 15.0

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  encryption password service

  !

  hostname gw.izmv

  !

  boot-start-marker

  boot-end-marker

  !

  logging buffered 51200 warnings

  !

  AAA new-model

  !

  AAA authentication ppp default local radius group of

  !

  AAA - the id of the joint session

  !

  clock timezone + 002 2

  !

  No ipv6 cef

  IP source-route

  IP cef

  !

  !

  Authenticated MultiLink bundle-name Panel

  !

  Async-bootp Server dns 192.168.192.XX

  VPDN enable

  !

  VPDN-Group 1

  ! PPTP by default VPDN group

  accept-dialin

  Pptp Protocol

  virtual-model 1

  echo tunnel PPTP 10

  tunnel L2TP non-session timeout 15

  PMTU IP

  adjusting IP mtu

  !

  redundancy

  !

  interface Loopback0

  IP 192.168.207.1 255.255.255.0

  !

  !

  interface GigabitEthernet0/0

  Description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE $ 0/0

  IP 192.168.192.XXX 255.255.255.0

  IP 192.168.192.XX 255.255.255.0 secondary

  IP nat inside

  IP virtual-reassembly

  automatic duplex

  automatic speed

  !

  !

  interface GigabitEthernet0/1

  no ip address

  Shutdown

  automatic duplex

  automatic speed

  !

  !

  interface GigabitEthernet0/2

  Description - Inet-

  no ip address

  NAT outside IP

  IP virtual-reassembly

  automatic duplex

  automatic speed

  PPPoE enable global group

  PPPoE-client dial-pool-number 1

  No cdp enable

  !

  !

  interface virtual-Template1

  IP unnumbered Loopback0

  IP mtu 1492

  IP virtual-reassembly

  AutoDetect encapsulation ppp

  by default PPP peer ip address pool

  PPP mppe auto encryption required

  PPP authentication ms-chap-v2

  !

  !

  interface Dialer1

  the negotiated IP address

  NAT outside IP

  IP virtual-reassembly

  encapsulation ppp

  Dialer pool 1

  Dialer-Group 1

  PPP authentication pap callin

  PPP pap sent-username DSLUSERNAME password DSLPASSWORD

  No cdp enable

  !

  !

  IP local pool PPP 192.168.207.200 192.168.207.250

  IP forward-Protocol ND

  !

  !

  overload of IP nat inside source list NAT_ACL interface Dialer1

  IP nat inside source static tcp 192.168.192.XX 25 expandable 25 82.XXX.XXX.XXX

  IP nat inside source static tcp 192.168.192.XX 1352 82.XXX.XXX.XXX 1352 extensible

  IP route 0.0.0.0 0.0.0.0 Dialer1

  !

  NAT_ACL extended IP access list

  deny ip 192.168.192.0 0.0.0.255 192.168.YYY.0 0.0.0.255

  deny ip 192.168.192.0 0.0.0.255 192.168.YYY.0 0.0.0.255

  deny ip 192.168.192.0 0.0.0.255 192.168.YYY.0 0.0.0.255

  deny ip 192.168.192.0 0.0.0.255 192.168.YYY.0 0.0.0.255

  permit tcp 192.168.192.0 0.0.0.255 any eq www

  permit tcp 192.168.192.0 0.0.0.255 any eq 443

  permit tcp 192.168.192.0 0.0.0.255 any eq 1352

  permit tcp host 192.168.192.XX no matter what eq smtp

  permit tcp 192.168.192.0 0.0.0.255 any eq 22

  permit tcp host 192.168.192.XX no matter what eq field

  permit tcp host 192.168.192.XX no matter what eq field

  permit tcp host 192.168.192.XX no matter what eq field

  allowed UDP host 192.168.192.XX matter what eq field

  allowed UDP host 192.168.192.XX matter what eq field

  allowed UDP host 192.168.192.XX matter what eq field

  !

  host 192.168.192.XX auth-port 1645 1646 RADIUS server acct-port

  Server RADIUS IASKEY key

  !

  control plan

  !

  !

  !

  Line con 0

  line to 0

  line vty 0 4

  line vty 5 15

  !

  Scheduler allocate 20000 1000

  end

  Debugging is followed:

  14:47:51.755 on 21 oct: PPP: Alloc context [294C7BC4]

  14:47:51.755 on 21 oct: ppp98 PPP: Phase is

  14:47:51.755 on 21 oct: ppp98 PPP: using AAA Id Unique = 8 b

  14:47:51.755 on 21 oct: ppp98 PPP: permission NOT required

  14:47:51.755 on 21 oct: ppp98 PPP: via vpn, set the direction of the call

  14:47:51.755 on 21 oct: ppp98 PPP: treatment of connection as a callin

  14:47:51.755 on 21 oct: ppp98 PPP: Session Session handle [62] id [98]

  14:47:51.755 on 21 oct: ppp98 TPIF: State of the event [OPEN] [initial check]

  14:47:51.755 on 21 oct: ppp98 PPP LCP: switch to passive mode, State [stopped]

  14:47:53.759 on 21 oct: ppp98 PPP LCP: exit passive mode, State [departure]

  14:47:53.759 on 21 oct: LCP ppp98: O CONFREQ [departure] id 1 len 19

  14:47:53.759 on 21 oct: ppp98 TPIF: MRU 1464 (0x010405B8)

  14:47:53.759 on 21 oct: ppp98 TPIF: AuthProto MS-CHAP-V2 (0x0305C22381)

  14:47:53.759 on 21 oct: ppp98 TPIF: MagicNumber 0xF018D237 (0x0506F018D237)

  14:47:53.759 on 21 oct: ppp98 TPIF: event [UP] State [departure at REQsent]

  14:47:54.351 on 21 oct: ppp98 TPIF: I CONFREQ [REQsent] id 0 len 18

  14:47:54.351 on 21 oct: ppp98 TPIF: MRU 1400 (0 x 01040578)

  14:47:54.351 on 21 oct: ppp98 TPIF: MagicNumber 0x2F7C5F7E (0x05062F7C5F7E)

  14:47:54.351 on 21 oct: ppp98 TPIF: PFC (0 x 0702)

  14:47:54.351 on 21 oct: ppp98 TPIF: RAC (0 x 0802)

  14:47:54.351 on 21 oct: LCP ppp98: O CONFNAK [REQsent] id 0 len 8

  14:47:54.351 on 21 oct: ppp98 TPIF: MRU 1464 (0x010405B8)

  14:47:54.351 on 21 oct: ppp98 TPIF: State of the event [receive ConfReq-] [REQsent to REQsent]

  14:47:54.751 on 21 oct: ppp98 TPIF: I CONFACK [REQsent] id 1 len 19

  14:47:54.751 on 21 oct: ppp98 TPIF: MRU 1464 (0x010405B8)

  14:47:54.751 on 21 oct: ppp98 TPIF: AuthProto MS-CHAP-V2 (0x0305C22381)

  14:47:54.751 on 21 oct: ppp98 TPIF: MagicNumber 0xF018D237 (0x0506F018D237)

  14:47:54.751 on 21 oct: ppp98 TPIF: State of the event [receive ConfAck] [REQsent to ACKrcvd]

  14:47:54.915 on 21 oct: ppp98 TPIF: I CONFREQ [ACKrcvd] id 1 len 18

  14:47:54.915 on 21 oct: ppp98 TPIF: MRU 1400 (0 x 01040578)

  14:47:54.915 on 21 oct: ppp98 TPIF: MagicNumber 0x2F7C5F7E (0x05062F7C5F7E)

  14:47:54.915 on 21 oct: ppp98 TPIF: PFC (0 x 0702)

  14:47:54.915 on 21 oct: ppp98 TPIF: RAC (0 x 0802)

  14:47:54.915 on 21 oct: LCP ppp98: O CONFNAK [ACKrcvd] id 1 len 8

  14:47:54.915 on 21 oct: ppp98 TPIF: MRU 1464 (0x010405B8)

  14:47:54.915 on 21 oct: ppp98 TPIF: State of the event [receive ConfReq-] [ACKrcvd to ACKrcvd]

  14:47:55.275 on 21 oct: ppp98 TPIF: I CONFREQ [ACKrcvd] id 2 len 18

  14:47:55.275 on 21 oct: ppp98 TPIF: MRU 1464 (0x010405B8)

  14:47:55.275 on 21 oct: ppp98 TPIF: MagicNumber 0x2F7C5F7E (0x05062F7C5F7E)

  14:47:55.275 on 21 oct: ppp98 TPIF: PFC (0 x 0702)

  14:47:55.275 on 21 oct: ppp98 TPIF: RAC (0 x 0802)

  14:47:55.275 on 21 oct: LCP ppp98: O CONFACK [ACKrcvd] id 2 len 18

  14:47:55.275 on 21 oct: ppp98 TPIF: MRU 1464 (0x010405B8)

  14:47:55.275 on 21 oct: ppp98 TPIF: MagicNumber 0x2F7C5F7E (0x05062F7C5F7E)

  14:47:55.275 on 21 oct: ppp98 TPIF: PFC (0 x 0702)

  14:47:55.275 on 21 oct: ppp98 TPIF: RAC (0 x 0802)

  14:47:55.275 on 21 oct: ppp98 TPIF: State of the event [receive ConfReq +] [ACKrcvd to open]

  14:47:55.295 on 21 oct: ppp98 PPP: Phase is AUTHENTICATING,

  14:47:55.295 on 21 oct: ppp98 MS-CHAP-V2: O CHALLENGE id 1 len 28 of 'gw.izmv '.

  14:47:55.295 on 21 oct: ppp98 TPIF: State is open

  14:47:55.583 on 21 oct: ppp98 MS-CHAP-V2: I ANSWER id 1 len 71 of "domain\username".

  14:47:55.583 on 21 oct: ppp98 PPP: Phase TRANSFER, tempting with impatience

  14:47:55.583 on 21 oct: ppp98 PPP: Phase is AUTHENTICATING, unauthenticated user

  14:47:55.587 on 21 oct: ppp98 PPP: request sent MSCHAP_V2 LOGIN

  14:47:55.591 on 21 oct: ppp98 PPP: received LOGIN response PASS

  14:47:55.591 on 21 oct: ppp98 PPP AUTHOR: author data NOT available

  14:47:55.591 on 21 oct: ppp98 PPP: Phase TRANSFER, tempting with impatience

  14:47:55.595 on 21 oct: Vi3 PPP: Phase is AUTHENTICATING, authenticated user

  14:47:55.595 on 21 oct: Vi3: given msg No. MS_CHAP_V2

  14:47:55.595 on 21 oct: Vi3 MS-CHAP-V2: SUCCESS O id 1 len 46 msg is "tG @ #QDD @(@B@ (@[email protected]/ ** / @I @:[email protected]/ ** / @@@ EJFDE)).

  14:47:55.595 on 21 oct: Vi3 PPP: Phase is in PLACE

  14:47:55.595 on 21 oct: Vi3 CPIW: protocol configured, start state cf. [original]

  14:47:55.595 on 21 oct: Vi3 CPIW: State of the event [OPEN] [Initial report on startup]

  14:47:55.595 on 21 oct: Vi3 CPIW: O CONFREQ [departure] id 1 len 10

  14:47:55.595 on 21 oct: Vi3 CPIW: address of 192.168.207.1 (0x0306C0A8CF01)

  14:47:55.595 on 21 oct: Vi3 CPIW: event [UP] State [begins to REQsent]

  14:47:55.595 on 21 oct: Vi3 CCP: protocol configured, start state cf. [original]

  14:47:55.595 on 21 oct: Vi3 CCP: State of the event [OPEN] [Initial report on startup]

  14:47:55.595 on 21 oct: Vi3 CCP: O CONFREQ [departure] id 1 len 10

  14:47:55.595 on 21 oct: Vi3 CCP: MS - PPC supported bits 0 x 01000060 (0 x 120601000060)

  14:47:55.595 on 21 oct: Vi3 CCP: event [UP] State [begins to REQsent]

  14:47:55.599 on 21 oct: % LINK-3-UPDOWN: Interface virtual-access.3, changed State to

  14:47:55.603 on 21 oct: % LINEPROTO-5-UPDOWN: Line protocol on Interface virtual-access.3, changed State to

  14:47:56.027 on 21 oct: Vi3 LCP: I have TERMREQ [open] id 3 len 16

  14:47:56.027 on 21 oct: Vi3 LCP: (0x2F7C5F7E003CCD740000030A)

  14:47:56.027 on 21 oct: Vi3 CPIW: event [BOTTOM] State [REQsent on startup]

  14:47:56.027 on 21 oct: Vi3 CPIW: State of event [CLOSE] [begins with initial]

  14:47:56.027 on 21 oct: Vi3 CCP: event [BOTTOM] State [REQsent on startup]

  14:47:56.027 on 21 oct: Vi3 PPP DISC: MPPE required not negotiated

  14:47:56.027 on 21 oct: Vi3 PPP: sending Acct event [low] id [8B]

  14:47:56.027 on 21 oct: Vi3 CCP: State of event [CLOSE] [start with initial]

  14:47:56.027 on 21 oct: Vi3 LCP: O TERMACK [open] id 3 len 4

  14:47:56.027 on 21 oct: Vi3 LCP: event [receive TermReq] State [Open to stop]

  14:47:56.027 on 21 oct: Vi3 PPP: Phase ENDS

  14:47:56.027 on 21 oct: Vi3 LCP: event [CLOSE] [off status of closing]

  14:47:56.675 on 21 oct: Vi3 PPP: block vaccess to be released [0x10]

  14:47:56.675 on 21 oct: Vi3 LCP: event [CLOSE] State [closing closing]

  14:47:56.679 on 21 oct: Vi3 LCP: event [BOTTOM] State [closing on Initial]

  14:47:56.679 on 21 oct: Vi3 PPP: compensation AAA Id Unique = 8 b

  14:47:56.679 on 21 oct: Vi3 PPP: unlocked by [0x10] always locked by 0 x [0]

  14:47:56.679 on 21 oct: Vi3 PPP: free previously blocked vaccess

  14:47:56.679 on 21 oct: Vi3 PPP: Phase is BROKEN

  14:47:56.679 on 21 oct: % LINK-3-UPDOWN: Interface virtual-access.3, changed State to down

  14:47:56.683 on 21 oct: % LINEPROTO-5-UPDOWN: Line protocol on Interface virtual-access.3, state change downstairs

  I'll be very grateful for any useful suggestions

  We had the same problem using MS-CHAP-V2 and 3945 router using IOS 15.2. When you add the same combination of username/password locally it worked fine but it wasn't no of course of the solution. We have solved this problem by adding the following line in the config file:

  AAA authorization network default authenticated if

  This is because Windows 2000 clients require the use of a statement of authorization aaa in the router config. Maybe it was default (and therefore not shown) previous iOS releases.

  Success!

  Wil Schenkeveld

• Can what comparison be made between time capsule and Smart RG s505 wireless modem router for wifi

  Can what comparison be made between time capsule and Smart RG s505 wireless modem router for wifi

  Superior...

  After all, the chip is mainly a modem.

  Wireless is there but not designed as the primary connection.

  Wireless 802.11n 300Mbps AP with 2 x 2 MIMO Wireless bridge, WDS multiple SSID, including isolated invited SSID WiFi QoS (WMM) and PowerSave wireless security: • Wi - Fi Protected Access (WPA, WPA2) • AES, TKIP, WEP encryptio

  It is the Wireless N standard.

  The TC is dual-band simultaneous AC1750... even if in fact apple never leaves anything use 300mbit on the 2.4 GHz is more like AC1450... It is also 3 streams on both bands not 2 x 2.

  The fact that aid.

  The only thing to note is that a router from Apple can join never a router wireless not apple... so, there must always be plugged in by ethernet.

• between my computer and router wireless connection (vista, premiem windows 7, 64 bit)

  Hey I recently had problems with my connection Wireless between my computer and the router.
  Normally off during the night is not connected to my router or on the internet the next day.

  I have been in close contact to my isp provider and have received a new router and reset my wireless Internet services provider site but I'm still having problems. I have also updated my drivers for my wireless on my laptop Hp G62 and have found that it will not cut when I do not shut down or sleep during the night.

  When you try to solve the problem, it will come back with "problem with the adapter or wireless access point and then asked to disconnect the power to the router. After doing this it will be fine all day.
  I do also to turn a blackberry 9000 "BOLD" and see first thing in the morning if the wireless is connected or not.

  ask for help, here is my last option I have been through everything and had an expert look at my computer where he found nothing wrong with my computer or wireless set up settings.

  any help or advice would be great

  Hello

  1. do you have problems connecting with Windows 7 or Vista?
  2. you remember of any change to your computer before the problem?

  Make sure that there is no interference between your router and your computer. For example. Mobile phones, like the mobile signals could conflict with your router signals and therefore no connection to your computer.

  You can uninstall and reinstall the Device Manager wireless network card.
   
  To uninstall the wireless device manager,
   
  a. Click Start, type device manager in the search box of start and press ENTER.
  b. Locate the network adapters and expand the same.
  c. Select the wireless connection, right click and choose uninstall.
  d. restart the computer, if prompted.
   
  Pilots should settle automatically after the computer restarts.

   

  Now you can install the latest wireless drivers and check if this solves the problem.

• Unknown device on network adapter between the laptop and the wireless router

  I am running windows 7 64 bit on a laptop computer connected wireless to the router and internet.  The router is Linksys WRT160N connected to the internet.  The map of the network, there is a question mark device unknown between the laptop and the router.  However, I still have access to the internet.  In terms of network, if I hover over the laptop, it does not show an IP address.  It only shows the name of the computer and its MAC address.  Any help would be appreciated.

  Solved my problem.  I checked the button of the IPv6 protocol in the properties of a network connection on the laptop, and now I can see it's the IP address and the unknown device has been replaced by a switch and hub which is part of the router.   I do not uncheck the button IPV4.  I'm guessing that it is a bug in Windows 7 that you need to cut of ipV6 Protocol when you have a Win XP computer on the network if you want to see a map of own network.  As I said before, everything worked before, so this seems to be a cosmetic fix only.  I see that my shared files on the XP computer appear faster after a reboot.

• What is the difference between call queues and priority routing?

  and what is the difference between routing based on skills and the basic skills of routing?

  Suite...

  Priority Queuing - Set Priority step can be used to assign a priority (1-10), or increase / decrease. This allows for a given

  Contact (eg. calling) to priority over higher/lower than the other contacts that are in the same queue. In other words, the contact

  priority for all s CSQ for which he is put on hold. In the script, you must use priority defined stage to assign a higher priority or less in Call Queuing.

  Check the following URL, which described on stage "Set priority" to the title of the palette "CIM step Description.

  http://www.Cisco.com/univercd/CC/TD/doc/product/voice/sw_ap_to/apps_3_1/English/admn_app/step_ref/ICD.htm

• 1841 can route between tunnel GRE and IPSEC tunnel?

  Hello everyone!

  See the image below.

  Main office (10.0.1.0/24 LAN) and branch (10.0.2.0/24 LAN) are connected through the GRE tunnel.

  The third office (10.0.3.0/24) is attached to the second branch via IPSEC.

  Is there the way to establish the connection between the third and the main office through cisco 1841?

  Is it possible to perform routing, perhaps with NAT?

  In fact we need connection with a single server in the main office.

  Thank you

  Hello

  It is possible to build this configuration.

  the IPSEC connection between 10.0.3.x and 10.0.2.x should also encapsulate the traffic to main office.

  Steps to follow:

  Central office, to shift traffic to 10.0.3.x above the GRE tunnel.

  The second part, add the 10.0.3.x - 10.0.1.x selection of traffic to the ACL IPSEC with the third

  The third part, add the 10.0.3.x - 10.0.1.x selection of traffic to the ACL IPSEC with the second pane.

  Please rate if this helped.

  Kind regards

  Daniel

• Failed to get the connection between the router WRT54GS and roku

  Hello

  I am new to this. How can I get my router to connect to roku.

  When I enter my password router Roku he can't find the router. And when I use Cisco Network Magic, it does not find the Roku device.

  Thank you... I didn't was not completely able to get in... but I found that my personal wpa password was different from what I used... and then I've always had trouble getting in... but this has certainly helped.

  I entered the MAC address and then I was in!

  I am so grateful to all who have contributed and are looking for me and we all in this forum

• Problems setting up router WRT1900ac and fiber

  I feel that my question is so obscure that I won't be able to get a lot of help here, but I'll post anyway.

  First of all, I live in the Philippines. My ISP is PLDT. I have FTTH - fiber to the home. My internet connection is DHCP - no login or password. I thought that perhaps they checked the serial number on the modem to see if I was an authorized user but apparently not; They told me if I wanted to buy another optical modem, I could and that I wouldn't need to do anything to save it on the network, but that they could not provide me with a list of modems that would work.

  They delivered to me with a router/modem made by a company called FiberHome. "Like the big business of high-tech directly affiliated to belonging to the active state of oversight and Board of Directors of the Council of State, FiberHome Technologies is the company of the kernel located in Wuhan Optics Valley of China."

  The model number is AN5506-04-FG. There are very few configurable on this. Can I change my wifi network name (they insist that the name of the network begins with PLDTHOMEFIBR, no idea why) and a few passwords here and there. For the most part, I just post status on the LAN and WAN.

  Therefore, because it is so little that I can do with it that I decided that I needed a router/gateway and not simply an Extender. I bought the WRT1900ac.

  Brought it home, that he repaired, it connected via ethernet cable between a LAN port on the FiberHome on the Internet on the Linksys port.  I then used the WiFi on my iPad to try on the Linksys Setup, try with Safari and Chrome.

  Went to put in place and smart control of Linksys could not understand my internet connection, despite several reboots, power off and cable disconnected, etc.

  So I went to the manual configuration. I put the connection to a static IP address. Following the minimal instructions in the booklet of FiberHome, I put the IP address of the router to 192.168.1.28; the subnet mask of 255.255.255.0; This gateway 192.168.1.1 (internal IP of the fiber to the home, address) DNS of Google DNS.

  This would actually work - but only for a few minutes at a time. Then the network diagram would show that I was always connected to the FiberHome but no connection to Internet in addition. (Although my PC, connected to the FiberHome via a LAN cable, still had access to the internet.)

  I used the live chat Linksys to ask an agent to this topic. She said that my gateway setting is correct. She had me reset the router and try again, but he could not yet know the connection to the internet on its own. She had me download the iOS app and try there, but same result. So I received a ticket number and ended the chat session.

  Now, I tried to set the internet connection on the router at the bridge. But once I did, I was unable to connect to the router via WiFi. I needed to do a reset to be able to access it again.

  At this point I called my ISP. They told me that if I wanted to add another router like that, they would need to reset my router/modem FiberHome bridged mode. But they are unable to do it remotely and cannot (or don't want to) give me instructions on how to do it myself.  They need to send a technician to my home. They could not tell me when. I have to wait for a call. (I got a ticket number).

  This means that for now, I have a blue and black, sitting bins there, I can't do anything with.

  So I'm waiting, I thought I'd post this in the hope that someone might have some ideas configuration I could try or for the general amusement of peoples.

  Thank you!

  You may have a conflict between the two routers in IP subnet. In this case the WRT1900AC will change it's default subnet to 10.x.x.x instead of 192.168.1.1

  You can find the new IP address of the router by looking at a customers connect ITI information IP address appears as the default gateway.

• WSN Routing Tables and better path decisions

  Hello

  My team has placed a total of 10 knots in an industrial environment of factory.  Nine are defined as routers, and there is only one end node.  The gateway is a little in the center of this area, and there is no node failed.  The coverage area is four floors with approximately 63000 square feet of floor area per level.  I'm having a problem with a section of the path used to reach the end node: a quality signal between the 3rd and 4th routers gateway has been ignored in favor of a lower quality signal.  If I take this 4th router and move it very closely the 3rd router and do a reset it will pick up the 3rd router signal and remain at about 60% intensity of the signal for several minutes.  However, this 4th router will soon fall sharply to about 20% intensity (much less that NEITHER recommended by 30%) of the signal.  The network is to decide than 3 jumps of signal is relatively good is worse than a jump involving a bad signal?  Also, is there a way to read what are routing tables to determine if it is indeed the case?

  Thank you!

  Garrett

  We suggest you use the least necessary routers for your background. Routers add the chance for the performance of the network has declined due to uninteded jump. Then, even when food is available, the default choice for the nodes must be nodes except routers are needed.

• My connection between my PC and the Internet.

  MY CONNECTION BETWEEN MY PC AND THE INTERNET.

  I sent a message yesterday - don't know if I got a response.

  My question is that something is wrong with my internet connection.  He died in line every 4-10 minutes of use.  I bought a new computer because my technician told me that I had a bad virus on my PC.  But now I have a new PC but my problem remains.

  Can what tests I do to see if the problem is with my wireless router, the Arris modem provided by Comcast, or something else.

  Please help me.

  Dave Fox

  my main email is , but I think I have the address of e-mail as .  so when you meet me you you the man or the other.

  But please reply to this email.

  You have the same problem if you connect directly to your router?

• Problem to create the Internet connection sharing between Windows XP and Windows Vista.

  Original title: Internet connection sharing between Windows XP and Windows Vista.

  Hello

  Recently, I plugged a laptop running Windows XP to a desktop computer running Windows Vista using a standard Ethernet cable with the intention of use sharing of Internet connection. The notebook contains a wireless connection that I've routed to the office via the cable said.  While the initial phase of installation went well (I was too lazy to do it manually, so I just used the Wizard "Set up a home or small business network" Windows XP,) I had to turn off the host computer to install a program. When I tried to set up ICS again, I couldn't connect to the Internet by using ICS. After this failure, I tried to configure the properties of TC/IPv4 (IP, gateway by default, etc.) manually, but I still couldn't run.  I am able to access the shared host PC and client files. It seems to me that some service essential to the proper functioning of the ICS may be disabled in some way, but it's just speculation, as I have no evidence of such a service. Help would be most appreciated.

  Thank you

  FG-man

  I tried this before using a laptop to share internet with my 360.  problem is there was Nat on the router, and it is in contradiction with the ics.

  Anyway long story short I did some research on the Internet and discovered that if you're behind a router ICS will be confllict with her, as ICS also does routing. a much better option is to "bridge the conections ' on the laptop.

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/hnw_bridge_install.mspx?mfr=true

  If you go this route, you need to set a static ip address for the office,

  Either that or if you want to continue using ICS put the laptop in the DMZ in the router may help, but it will be less secure.

  Hope that this helped good luck