Tecra 8100: Need exact specifications

Similar Questions

• Need a specification complete for Tecra R10 - 147

  Hello!
  Can someone give me please the specifications (especially for the 3G chip embedded) for my Tecra R10-147.
  I need some specific technical information that I can't find anywhere on the net. Tecra model doesn't even exist on the Toshiba site. I'm french, and perhaps that is an exclusive model for the France or Europe.
  Thank you

  Matt

  It is not easy to find the complete specification.
  I'm sure you know what components are inside.

  About 3G I just make it is - 3 G HSPA FOR EU - 7.2/2.0MBPS DIVERSITY and supports the European region.

  What do you want exactly?

• Need driver Ethernet for Tecra 8100

  I need a driver ether c16 ether c16 for Tecra 8100

  Hello

  All the drivers that are released by Toshiba are on the European driver Toshiba-> archive page

  http://EU.computers.Toshiba-Europe.com-> support download &-> download drivers

  I m not sure what driver do you need exactly, but all Toshiba drivers are located on the driver page.

• Need a display driver (s3) for Tecra 8100

  I installed Windows XP pro on my tecra 8100 and cannot get a full screen.
  Someone knows what's the problem? Do I need a new display driver voor the S3 Savage MX, or is it something else?

  Hello

  check in the Bios if the "Fullscreen/Widescreen" setting is enabled.

  Best regards

  Ben

• Tecra 8100 did poster need nothing on LCD - LCD cable

  Hi, my Tecra 8100 13.3 "laptop does not display anything on the LCD screen. It works with the VGA. I'm looking for a LCD cable for this laptop. Any body know where I can buy one. Any body know what is the part number FRU for this. Not the cable of the LCD screen for this model and other model is different?

  Aryabhatta

  Hello

  You will be very happy if someone has so much information for you. In my opinion, you should check if you can find the same parts and don't forget that you can exchange it. Tecra 8100 is about 6 years old and find new parts can be difficult.

  I put t know which country you live but try to pick up a few pieces of notebook offering online in your country. Second option is to check eBay. From time to time, you can find there defective laptops, but many pieces can be used for replacement.

• Need of SDRAM for my Tecra 8100

  Hello everyone.

  I would like to buy a souvenir for my Toshiba Tecra 8100
  It is and must be SDRAM 256 MB PC100 144pin - may by already used but functional

  It is too difficult to buy in my country
  I can pay for it about 20 euros

  Thank you

  Already find you on sites like Ebay or Amazon?
  Several months ago I ve bought a 512 MB RAM PC100 because my old module is dead.

  I ve found some modules of second hand on eBay but I ve decided to buy a new Amazon module

  Good bye

• Need driver graphics card for Tecra 8100

  I have a Tecra 8100 810-1With Win98 series.

  I format the HARD drive and installed Win2000pro but some drivers not found on CD as graphics card, sound card and Ethernet card.

  After my laptop have only the 16colors and the small window that opens.

  I upgraded W2000pro by Microsoft Update for IE7, and service pack 4.

  Other readers to another device, I founded, I installed them and they work well.
  Only for the graphics of the very hard to find map drive for S3 savage/IX w/MV.
  I find 79036agplogo_S3.zip

  I tried to install it, the installation is OK.
  But when I started PC I have an error message in French, I translate it:
  "The pilot \Systemroot\system32\drivers\s3gsavm not found the point to enter the VideoPortSetEvent on the VIDEOPRT.sys drive.

  I tried to download it, but never found the driver for the graphics card, this is the link [http://fr.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=FR]

  Perhaps the drive on which I founded are not good? Where can I find it? Can you give me the link please correct?

  Thanks for help.

  Follow the link you have posted.
  Choose the category "Archive". Here you will find all Tecra 8100 drivers for windows 98 and Windows 2000.

• Tecra 8100 - exchange of motherboard

  Hi all.

  Sorry, my English is not very good, but I need help. My Tecra 8100 does not only turn on the leds of power, battery and drive hard, but does not (Nothing on the screen).
  I need to replace my motherboard and it is B36084962019-a (Tecra 8100 model PT810E-01152-IT) but I think only B36086672015-A motherboard.

  Can I use these model instead of my?
  Thanks in advance to all.

  Hi tibi_1,

  Your English is ok and train me it s understandable so don t you worry about this and welcome to the forum :)

  About your problem, I can t give an exact answer, but a Council: contact an authorized service provider. I think that in this case you need 100% sure answer and you can get it from professional people only because it s a user to user forum where you can talk with normal people like you and me.

  Then get in touch with the guys, they will help you and if you are not familiar with laptop disassembly, they can help you to swap the motherboard.

  Good luck! ;)

• Tecra 8100 - screen goes black sometimes

  Hi members,
  I recently got a Tecra 8100 for cheap on eBay.

  The screen sometimes goes black its still on I need to press the shaft close to the screen and it beeps sound sounds and back on.

  I removed the frame of the screen and it made the difference for a about a week but just happen again:(mais je croise les doigts pas très souvent.)

  I read on google etc. it can be sumtin with led, etc. I just want to know how to replace the part?
  What part I need to replace etc.?

  I disable all power management things, and sometimes even of it is would no doubt something with the screen.

  I need ideas how to resolve this because it's a good laptop for a student lol prity.
  Thanks for reading and any rear power

  Hello

  Sorry, but it's really not easy to say what needs to be replaced.
  But it s certainly a hardware problem I put t know what should I PIN you meant exactly, but maybe a loose connection is causing this problem I mean a FL-inverter connection

  Here's a useful page [how remove and replace card ups FL on Toshiba Tecra 8100 | http://www.irisvista.com/tech/laptops/Toshiba-Tecra-8100/remove-replace-fl-inverter-board.htm]

  Maybe it could be useful for you

  In any case, these hardware issues are always delicate, and in most cases, each unique piece, and the connection must be checked. It's not easy, and in most cases and the computer laptop technician should take a look on this laptop

• Tecra A11-125 - technical specification on the integrated chip

  Hello

  Where can I find more info for the Tecra A11-125? Specifically, I need to know the SATA standard for the chip: is Sata150 and Sata300?

  Thank you

  Oliver

  Hello

  I found an article on this laptop:

  http://www.notebookcheck.com/test-Toshiba-Tecra-A11-125-notebook.28130.0.html

  According to her, it is equipped with motherboard Intel HM55

  http://www.Intel.com/products/Notebook/chipsets/HM55/HM55-overview.htm

• Tecra 8100, upgrading the BIOS, whitch that hard drive is taken in charge (40 GB)?

  Hallo,

  I have an old Tecra 8100 one I want to update BIOS. Who knows who is supported (20 GB, 40 GB) hard drive and where can I find the specifications?

  Thanks for your information.

  Georg

  Hello

  As I m wrong not the Tecra 8100 does support an IDE HDD controller.
  In this case, it should be possible to use the 2.5 IDE HDD.

  I can't say much about the formats supported, but the fact is that the size of HDD supported depends on the HARD disk controller. The old controllers IDE up to what the ATA - 5 (also called Ultra ATA/66 or Ultra DMA/66) supported LBA 28 bits, which allows you to use the 120 GB HARD drive max.

  Since ATA - 6 (also called Ultra DMA mode 5 or Ultra-ATA100), you can use IDE hard drives of more than 128GB.

  So if you want to, you can check your IDE HDD controller using a hardware diagnostic tool (IE Everest home edition). Then you might find out what IDE controller is and what drives are supported.

  See you soon

• Install W2K on Tecra 8100

  Hi all

  I am trying to install W2K on a Tecra 8100, but I think I'm doing something wrong, because it keeps failing.

  If I just insert the CD it starts to start a load several files at a time when the Setup starts Windows 2000 (present at the bottom of the screen) and the installation crashes with a blue screen and the c0000221 error material unknown error \systemRoot\System32\ntdll.dll
  I read that, during installation, you will need to press F5 (in the screen where you can load a SCSI or raid driver) and then choose Advanced Configuration and Power Interface (ACPI) PC, but after doing this I get the same error.
  I have no additional material attached, it's original configuration.

  Any thoughts on how to solve this problem and get W2K on my laptop?

  Hello

  I think that this question has nothing to do with the Advanced Configuration and Power Interface (ACPI) or similar.

  I read about the error systemRoot\System32\ntdll.dll message, and there is no particular reason for this error.
  Sometimes some service packs missing cause this problem and sometimes hardware malfunction (RAM or HARD drive) could be responsible for a BSOD.

  You are able to install Win XP?

• Tecra 8100: Advice replace please - audio card?

  My 8100 Tecra faithful and beloved which is ideal for my purposes locked up the other day, in the middle of a session.

  Restart windows resulted in blocking machine once Windows is running.
  I started in safe mode - no problem.
  I have disabled all devices useless and then through a process of elimination of selectively allowing devices and reboot.
  I found that the problem was the Yamaha audio device - that turn on the machine and it would lock up, disable that and he would normally go.
  It worked fine now for a day with the disabled Yamaha audio device.
  I tried to uninstall/reinstall the device - no change.
  I even did a fresh install of XP - no change.

  I ran XP pro for over a year without problem (so far) and I consider not audio as criticism - just a nice to have.

  My questions are:

  Is there anything else I need to do in the way of diagnosis?

  Tips for common problems?

  Can anyone with experience of fixing these machines or similar notice if replacement of all of the audio card is likely to make a repair?

  I seem to remember the last time that I opened it about two years ago to change the processor that the audio Assembly was on a separate panel but is that all?

  Note that this is a _ancient_ machine and _not_ going to be taken to a repair shop where the Bill would be more that it is worth! I am competent to replace the sound card, more than that and I will probably continue to run without audio - I don't think that it worth replacing the motherboard just for audio...

  Thank you very much in advance for any constructive suggestion.

  Well, as you know these replacements are very delicate
  However, I don t think you will be able to replace this sound card but it s my personal opinion.

  From my experience, I know that the card (audio driver) his Yamaha is not fully compatible with Win XP SP1 and SP2. Update the audio driver is necessary.

  Google for it

  I searched a bit for some instructions how to remove these boards and found this page.

  There you should find a link to the page how to disassemble the Tecra 8100.
  http://repair4laptop.org/disassembly_toshiba.html

  Greetings

• Tecra 8100 freezes after 45 minutes to an hour of use

  Hello

  Have a toshiba tecra 8100 and improved the Win98 operating system is XP Home. After installation, Windows update has installed all updates. Now, after 45 minutes of use, the computer freezes. Furthermore, it is still a Win 98 folder in the computer. Should I remove this? Could it be the cause of the problem? I would appreciate help with this. Thank you.

  Hello

  I agree with asil. It is possible that your device has enough RAM and one moment is easy to much and laptop freezes simply.

  If you need info on writing RAM upgrade again.

  Good bye

• Tecra 8100 white plus-ecran only starts

  I have a Tecra 8100 (disc hard 12 GB 700 MHz, 256 MB of memory) running Windows XP and Win 98 dual-boot. It was OK for ages but suddenly developed the following fault. Any help to heal would be great. When you turn it on, normally, the screen remains blank, the hard drive is ringing and the lights are on, on the front panel. No keyboard entries do start/start etc.

  When you press the off button, sometimes it'll just off as usual, at other times it will be bleep 30 times, then stop. Keep the power off button will require cutting as it should. Sometimes, lights up the screen and you can start up to Windows XP/WIN 98 etc but the PC freezes on the way to start, or when he gets there, you can't do more with it when this happens.

  The CMOS battery is down to 2.77 volts instead of the 3 volts, it should be, I took out memory, tried both sticks of memory in slots and nothing makes no difference. I think that it is an intermittent fault, but it's a common fault, like others on another site to help describe EXACTLY the same symptoms.
  EVIDENCE OF THIS PLEASE!

  Hello

  I saw your ad on http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=15134 and assume that you have found the solution.
  It really works?