LaserJet 3030: problem with number of copies

Similar Questions

• Color laserjet 4600 - problem with one color (yellow) for the most part does not print

  Colors look purpleish when printing photos.  It turns out that this is a problem with yellow print.

  We tried to replace the yellow toner cartridge, and it was not fixed.

  PQ troubleshooting, the yellow page is empty except for a thin (16th of an inch) to 99% a horizontal line at the top of the page.

  In the configuration page, all the different areas that should have the yellow are mostly empty, with the exception of the same sort of thin horizontal line at the top of each of these areas.  After updating the firmware from 03.001.0 to 03.016.0: in addition to what is described on the configuration page, some of the fields in the configuration page that should be yellow, have a pale magenta and more this yellow line.

  Our technician came several times and has so far tried to replace the hvps, scanner laser, toner alignment and trainer kit Board.  Nothing has improved the question.  Then for the replacement is the regulator dc ($1000).

  Anyone here have an opinion on what could cause this problem?  It seems they are just throwing parts at home and we're about to tell them to give up.

  It wasn't the dc controller.  I figured out well out - somehow, there was a spring missing behind one of the speeds in the train of drum roll.

• HP LaserJet 4100: Problem with the universal print driver

  Desktop: HP Envy 700-214

  OS: 10 64-bit Windows

  Printer: HP LaserJet 4100 (with a USB to parallel cable)

  I was able to properly use my LaserJet for Windows 8.1 through my Windows 10 crossing (which I upgraded to about 18 months ago).  Quite recently, I welcomed Windows Installer a upgrade, and at this time there, I lost my ability to print.   It has been on my default printer, but gave an error message when I tried to print.

  I tried to "Add a printer" and selected the HP 4100 connected to the LPT1 port.  It would not print a test page, and the printer does not like in the reception of data.

  I then tried to install the (PCL6 and Postscript) universal print driver with similar lack of results.

  I tried uninstallinDeg and reinstall the drivers, but once again no joy.  Incidentally, although I'm going to Device Manager > printing queues and remove the drivers, when I set up an application like Word and select the Menu printing, many copies of drivers rest yet.  When I go to remove them using the printui/s/T2, it is said that they are currently in use and cannot be deleted.

  Yet once again, I repeat - it is not a hardware problem because everything worked well before Windows upgrade.  I just need to find a way to reinstall a driver who will speak to my printer.  It of frustrating because I was able to do that before, but may not know what I am doing wrong.

  Thanks in advance.

  Hello GaryLynn,

  You saw did a lot of things to try to solve this issue.

  However the USB to parallel isn't anHP officially supported connection type.

  in any case, what suggests I´d, is that you try this:

  • Unplug the hybrid cable that you use
  • Uninstall all copies of the printer and its duplicates.
  • Stop the print spooler by using the services on windows (type on cortana services.msc) locate print spooler and stop it
  • Go to run and coil type, look at the Printers folder and delete all the files that are there (if any)
  • Restart the spooler to print services.
  • Download and install this driver package
    http://h20564.www2.HP.com/hpsc/SWD/public/detail?swItemId=FP-148007-1
  • Turn on your printer and connect the cable.

  After this exercise, check to see if windows 10 has managed to find the best driver to use your printer.
  If widows did not automatically find it, try the manual on add a Printer Wizard.

  If not reading as LPT1, check ports either USB00 ' # ' or a port DOT4, those who should be the ports to use.

  I hope this helps you get your printer going again.

  Thank you

• HP LaserJet 3200 - problem with printing ink, hoof?

  Product name & OS: HP LaserJet 3200 all-in-One / Windows XP

  When a page prints, there is a gap that occurs on the page that runs the entire length of the page where there is text.  It's like a line, but not a line... the opposite in fact.  Everywhere where there should be text/ink, he is absent.  Gap space is the equivalent of one letter of text width.  Once the page is printed, when you look at the page, it has the appearance of a line of ink missing from the top of the page toward the bottom of the page.  It's as if there's a filibuster any.

  In addition, this only happens in copy mode, NOT print mode.  Specifically, everything I print from my computer comes out perfect with no problems.  It's only the pages I put in the feeder and press the copy that eventually this problem.  Thanks for any help that anyone can provide.

  Hello selectmarketing,

  To get your question more exposure I suggest you post in the trade forums as the HP LaserJet 3200 is a commercial product. You can do the HP Enterprise business community.

  The support of your product page can be useful in the meantime:
  HP Support Center.

  I hope this helps!

• LaserJet 1600: problem with printing on color laserjet 1600

  I just replaced all color cartridges, but the left side of the print is faded.  I cleaned it up, and I don a supplies status page.  black and cyan colors print correctly.  yellow - the left third of the color bar is faded to white.  Magenta hardly shows in color at all.

  any suggestions?  Thank you

  Problem running on this series with the Magenta.  Yellow it is possible also, but more than likey you have a bad toner.  See instructions attached on how to fix.  A lot of work but not so hard.  Usually I leave the track of wire black plastic which crosses the upper part as it is a bear to get back up and is not necessary.  A couple of tie wraps will do the trick.

• LaserJet P2035: Problems with a LaserJet P2035

  I have two HP LaserJet P2035 and both will send jobs not from the paper tray.  They two fine prints from the manual feed tray 1.  When I close the manual feed tray 1 and try to use the paper in the paper tray, the paper light keeps blinking and will not clear. I have performed the update of the firmware on the two units that made no difference.  I would greatly appreciate any suggestions.  Thank you!!

  Thank you freginold.   I found the culprit.  I have slightly bent a metal cross bar support located under the paper tray upward toward the printer.  This bar triggers the lifting of the paper tray mechanism to lift the paper in place and of course, there was no contact. This solves the problem.

• Problem with number blackBerry Smartphones

  Hi all

  A few days ago, I had my cell phone number changed because I had malicious calls from unknown numbers ect. But my old number still shows upwards in line 1 when I discover call logs and it also appears when I connect my BB to my computer.

  How can I change line 1?

  Hi and welcome to the forums!

  Try the steps listed in the attached article.

  Thank you

  Bifocals

  KB01889 "My number - unknown" is displayed instead of the number of the user on the BlackBerry smartphone

• LaserJet 600 m602: Laserjet 600 too large print the number of copies

  I work at the public library, and we have a Laserjet 600 m602 to our public access computers to use. It is a network printer. We have problem with printer what impression of the office 2010 products, if more than one copy is requested printer will go crazy and print several copies much more than requested. The printer screen will say 1 X print the number of copies. Only way to stop it is to remove as many jobs he sees. It acts as if it were several jobs. We do not see this problem when printing from the Internet. Driver HP laserjet 600 M601, M602 M603 PCL6 HPCM600c. processor is set to WinPrint - Raw. Bidirectional support is disabled.

  Firmware is 2305090_000468

  I had already installed the pilot PCL6 universal and implemented to date to 600 M601, M602 M603 PCL6 thought that could be the problem but it has not fixed the problem.

  I would appreciate any help on this matter before going to is broken on paper.

  Thank you

  Melanie

  Solved.

  After a lot of research on reading and tests finally discovered the problem with drivers print and collate. Default settings for Microsoft Office 2010 and Adobe Reader are to gather if one that one copy is activated. For some reason any that caused printer to go crazy.  I tried the Standard driver and universal for the printer, but always had the problem of printing too many copies. I used the PostScript driver and it solved the problem.  Now just get the number of copies required. Thank you for your help.

  Melanie

• Problem of the printer prints do not number of copies

  I was using a HP LaserJet 1160 for 4 years with no problems to speak of. I had a computer of my last XP computer crash and bought this new Vista system 3 months ago. Since installing my printer on this new system Vista no matter how many copies I choose to print from a print window it will give me only 1 copy.  Very simple problem, one might think. I had my team Lightspeed System Support remote access to my computer and they have checked drivers and tested the problem. When I go to print something, I enter the number of copies that I want, and then click on print. I put in 5 copies and it will give me only 1. No matter how many copies I request so that it will only give me a. Nobody knows how to solve this apparently simple problem? I reinstalled the printer. I reinstalled the drivers. I went to Vista Home Premium, Vista Ultimate, I always have this problem.

  Hello

  When was the last time it was working fine?

  Try to uninstall then reinstall the printer drivers.
  http://h10025.www1.HP.com/ewfrf/wc/siteHome?lc=en&DLC=en&cc=us

  All the best!

• Printing problems - number of copies squared

  We have two different computers with Windows 7 Pro.  One is 64-bit, 32-bit.  Both have problems with the number of copies being squared when print on some programs - the 64-bit HP printer, and Word is the program of boredom.  the 32-bit has a cannon, and Printshop 23.1 is the program of boredom.
  By checking on the web, it seems that this problem exists also in Vista and many other types of printers.  Help!

  Hello

  I'm happy to have helped. Sounds like you were doing a few very good troubleshooting.

  Please check that really helped as the answer so that others can find them.

  Move every day, go further

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• The upgrade to Windows 7 with my Laserjet 3030 scanner

  I retired recently my PC and XP in exchange of new PC (HP) with Windows 7. Most of the time, everything went very well. Nice OS. However, I had to get a new driver for my HP Laserjet 3030 of HP to make it work with Windows 7. Their only choice was a universal driver for this printer. That worked well, except that I lost all my other features All in One printer scanner IE. The scanner is waiting for the PC, but it resets after 30 seconds without analyzing. I looked for additional drivers solve, but HP does not seem to offer to those who understand the scanner. Any suggestions?

  And Yes, I have a PDF reader and a printer. None of them has no menu to offer a solution. All suggestions are welcomed and appreciated.

  After more reflection and lack of comments on this issue, I decided to install XP virtual emulation to solve the problem. I use the scanner from time to time, is important to my home office, but can work with the obligation to switch to XP. I installed the feature on my computer from my wife when its software would not work in Windows 7 and it works fine. I think this solve my problems until HP gets with the program and supports drivers in order to cover all the features of the Laserjet 3030 All in one. Hope that this announcement will help others who have the same problem.

• HP Laserjet 3030 works only with Windows 8

  Original title: NEW COMPUTER AND OLD PRINTER NOT TALKING

  HAVE A NEW INSPIRON 7 SERIES LAPTOP AND AN OLD HP LASERJET 3030 PRINTER

  I TRIED INSTALLING WITHOUT SUCCESS... Help!

  Hi Rachel,

  1. don't you get an error message when you try to install the printer?
  2. are you trying to install the printer driver from the CD of the HP provided software or directly on the site.

  HP Laserjet 3030 is compatible with Windows 8. Here is the link.

  You can install the printer from the HP website driver and check if it helps.
  http://h20565.www2.HP.com/portal/site/hpsc/template.page/public/PSI/swdHome?sp4ts.Oid=378058&AC.admitted=1393155693969.876444892.492883150

  See the articles.
  Problems installing printer with Windows 8
  http://WWW8.HP.com/in/en/support-topics/Windows8-support/printer-install-issues.html

  Set up and install.

  http://h20565.www2.HP.com/portal/site/hpsc/public/PSI/setupInstallResults/?lang=en&cc=us&sp4ts.Oid=378056

  Let us know if it helps. If the problem persists, we will be happy to help you.

• you have tried to contact me to solve my problem with my iMac, but it seems contact you number is wrong

  HI I mayada I have the case Id * and the serial number of my iMac is C0 * NCR you have tried to contact me to solve my problem with my iMac, but it seems the number you contact will not my right number is + *.

  Mayada

  < personal information under the direction of the host >

  If you are referring to Apple is not Apple. Here are the forums of users only. Call Apple directly to deal with your problem.

• Having a problem with payment or purchase of an online number

  Having a problem with payment or purchase of an online number

  Help me to try to have Skype on my cell phone now, thank you very much

• Problem with the number of lines in the channel

  Dear community LabView,

  I'm relatively new to labview and I came across a problem that (I assume) can easily be resolved with your help.

  I need to create a digital signal to trigger a camera, but I have a problem with the configuration of my lines or exit lanes. I would not use that line output to trigger the camera. (I use a card NI PCIe-6353). LabVIEW is telling me that the number of lines in the channel does not have the number of rows of data:

  Possible reasons:

  Specified read or write operation failed because the number of rows in the data of a string is not the lines in the channel.

  If you use the digital waveform data type, make sure that the number of lines in the digital waveforms is the number of lines in the channel. If you are using Boolean data, make sure that the dimension of the array for the rows of the data is the number of lines in the channel.

  Number of lines in the channel: 1
  Number of data lines: 2

  Task name: _unnamedTask<11>

  How and why the number of data rows is connected to the resolution of my analog digital converter?

  I would appreciate your help! Labview code and a screenshot attached.

  Thank you

  Beff

  I got it to work by changing the "data format" "binary not signed" OR by plugging is not the "offset" for the Square Wave VI.  I think that the default "offset binary" data format works correctly if there is a negative value.