LaserJet M750dn: LaserJet M750 light print in all colors
I printed the print quality troubleshooting pages and all the colors are uniformly low (no streaks or lines). I checked to make sure that the printer was connected to the wall and not a surge protector. I have cleaned the inside, checked the contacts of high voltage and ran the Windows Laser cleaning procedure. I also ran a full calibration. None of this has worked. Then I went in pre-launch and cleaned the disc then updated the firmware to the last 2305090_000473.
The client uses the brand HP toners. The transfer Kit is 90% and in good shape, so it is hard to imagine that it is defective. Should I try one or both power supplies high voltage? There a PCA HV of imagery and a secondary transfer HV ACP? Who would try? Or both?
I replaced the secondary transfer HVPS to solve the problem. So happy that the repair has been resolved.
Tags: HP Printers
Similar Questions
-
Good evening, everyone.
I have a printer J4680 AIO that I had for a while. Last night, I installed the new ink and ran a test page and it looked ok, but when I went to print a chart, I noticed that the colors were COMPLETELY shut down.
I went online and print a test page which includes all colors including shade and hue of these colors.
The result is... interesting...
The yellow is a lime.
Red is a deep blood red
Magenta is magenta, but deeper... almost purple in hue
Black is fine
The Green is very good.
Blue is fine
Cyan is fine
What it boils down to, is that cyan is printing in all colors.
Anyone had this happen and have any idea of a resolution for this? I do a lot of graphic design and when I am doing a project that does not require my printer super high resolution (aka REALLY expensive of ink), I need it to be precise.
EDIT:
I should mention that I use ink official HP (901) so I know it is not the question (or shouldn't be).Be troubleshooting steps described here can help, it seems that you have in the mixture of the color cartridge. It is unlikely that running a cleaning cycle will solve this problem, you will probably need a new cartridge. You can check the warranty on the cartridge (valid even if the printer is no longer guaranteed) as indicated in the paper here.
A new cartridge will almost certainly fix the problem.
-
Printer Epson stylus CX 6600 print perfectly all colors except black who is hitting and missing
Printer Epson stylus CX 6600 print perfectly all colors except black who is hitting and missing
This looks like a printhead clogged for me.
It's more of an Epson problem than a problem of Windows.
Check the Web site of the Epsom for utilities seeking to lead the printheads.Here is a link to the CX6600 troubleshooting page:
<>http://www.Epson.com/cgi-bin/store/support/erscripts/start_er.jsp?BV_UseBVCookie=Yes&OID=41664 >HTH,
JW -
Print all colors with the exception of cyan, so blue and green print under rose. I have cleaned the nozzles according to the instructions, there is a lot of ink in each cartridge and it worked a few days ago.
Hello
Check with Canon support, their documentation and online drivers. As Canon OEM is responsible for
for the proper functioning of the printer and drivers provided.Canon - Support and drivers
http://www.USA.Canon.com/Cusa/support/consumerCanon - Windows - Vista and Windows 7 support
http://www.USA.Canon.com/Cusa/consumer/products?pageKeyCode=windowsSupportI hope this helps. Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.
-
printer is, BUT only with black and blue, all other diagnoses print with all colors
Initially, the installation of the printer REFUSED to align, took 7 attempts (OK, I've heard of Einstein quote!). Whenever I used the printer to ALIGNER PRINTER screen - the process has failed. So I looked on the web, and:
Clean the cartridges,
Erased the vents
Removed and cleaned the print head
Prayed
Tried again
To nothing not done, so I tried to make the diagnosis via PC software and here deepened the mystery.
When the HP Photosmart B210 series Toolbox running I got three different results between the three print options
A Diagnostics Page of print quality gave me five Ba's maximum color printing
Align the print heads gave me the black and blue boxes/lies/grids and the message alignment successful
The print Diagnostic information gave me all four colors with a lot of useful info, including the print head 73 calibration trust level: 0
Ideas anyone, before I bin it and buy a Kodak or disgusted Epson
What exactly is the problem? Alignment aligns the print head color to the black print head, and black and one color (cyan for your printer) are required for this. (There is probably an extra set of blocks that prints gray blocks fade to white. This section is used to calibrate the energy for the colors). The other test pages that you printed will be print various diagnoses or test pages that will use all colors.
A successful alignment page requires the page be printed on white paper not used and requires that the cyan and black sections print correctly.
-
I have the screen things different impressions on the internet and all the colors showed up... even black. Any ideas on what could be the problem
Hello
I would like to know the out come of the steps in my previous post. You can also follow the steps in the link below.
Solve printer problems
Given that the problem is related to Microsoft Office Word, I suggest you to post the question on Community Support in Microsoft Office Word.
Community office
http://answers.Microsoft.com/en-us/Office/Forum/Word?tab=all
Write us with the State of the question.
-
OfficeJet 6500 new black cartridge installed, but print Brown (all colors) instead
Hello
I replaced the black cartridge in my OfficeJet 6500, and clicking on it. (I triple checked it.) However, when I try to print a document that is supposed to be any black ink, it prints in a Brown shade as if it is mix inks instead of using black-colored. I printed a diagnostic page, cleaned and alignment of the heads of print and even restarted the computer and the printer. Nothing helps! I am still at work and I have documents that need to be printed!
Do you have any suggestions?
Thank you!
What operating system do you have? For Windows 7, you would go to start, devices and Printerss, right-click on the Officejet 6500 and then select Printing Preferences. You can change the setting 'document Type' in the tab 'Features', then click on apply.
The above will change the default value. You can also change the print to a particular print job by selecting the print properties when you go to print.
-
I have an OfficeJet Pro L7590
I tried to print something with a clip, but the colors were incorrect. I then used the align printing functionality and it printed yellow, magenta and black but not cyan. I changed the cyan cartridge (even if she did not show empty on the Panel), but even once it does not print on the cyan. I don't know what steps I can take to fix this problem. Your help would be very appreciated.
Thank you.
Looks like you have a dead cyan printhead. I'm sorry.
-
LaserJet 500 m551 - print CMYK color
Hello!
I need to print separations on m551 color LaserJet 500 files.
In particular, I file separations there was only CMY colors. And black color (gray) got to mix C, M and Y.
I had used PLC and PS driver, changed options, but printer uses all colors. Black color in use, I have seen on the photo printed by microscope.
What should I do to correct printing?
Best regards, Alexander.
I'm sorry, but to get your question more exposure I suggest posting in the trade forums since it is a printer. You can do to Printers - LaserJet. Click new message.
I hope this helps.
-
where can I find the drivers for my hp laserjet cm2320 mfp printer
I couldn't find a driver for hp color laserjet cm2320 mfp printer. My system is win 7.
I couldn't find a driver for hp color laserjet cm2320 mfp printer. My system is win 7.
-You know what you have for hardware: HP Color LaserJet CM2320 MFP
So... what say you HP?
Hardware support - including the drivers and other software that allow the device to interface with other software and hardware - is the manufacturer of the hardware device.
This printer has been essentially abandoned in newer operating systems HP all in time, it seems...
http://h30434.www3.HP.com/T5/printer-all-in-one-software/CM2320-MFP-has-been-abandoned/TD-p/218486Although it should 'work '...
You can get the drivers and software, you can HP. Select your specific printer if...
-
My printer is all colors except black in pink. So I can get black and pink print
Hello
As Canon OEM is responsible for the good operation of the printer and their
drivers provided. Check with Canon support, their books online and
drivers and ask in their forums (if any).Canon - Support and drivers
http://www.USA.Canon.com/Cusa/support/consumerCanon - Support - contact us
http://www.USA.Canon.com/Cusa/consumer/standard_display/contact_us_consumerCanon - Windows - Vista and Windows 7 support
http://www.USA.Canon.com/Cusa/consumer/products?pageKeyCode=windowsSupportCanon printer - page local confirmation - could be from another region.
http://pdisp01.c-WSS.com/OS/I hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="">-><- mark="" twain="" said="" it="">->
-
Printer does not print. All the flashing lights
HP 1300 printer has stopped printing. All the lights flash. any advice?
If your printer is a HP LaserJet 1300 so please see if it helps:
-
My HP Laserjet 1320 leaves printing several copies of a single document several weeks ago. Yesterday, I uninstalled, reinstalled, turned off the printer, unplugged, it turned on and plugged in. The computer '' recognized '' a new piece of hardware, installed a pilot... nd then refused to print at all, not even simple. After that, I turned off everything, unplugged and replugged the printer and still nothing. Then I checked the updates and found that HP has had a new update to the 1320 in December, so I tried to install that (three times), but it will not install. I just get a failure message. I have Windows 8 on my desktop PC. I have also (used to) have the printer configured so I could access it from other computers in the House to print via wi - fi. Help! I have a job for which I need to print 600 copies of a single document, and now I can't print anything.
Sure, go ahead and remove the second printer 1320.
My installation of 1320 under Win7.
Strange the HP has a USB port in the support doc.
-
LaserJet Pro 400 M451nw: Laserjet Pro 400 prints documents upside down
My Laserjet Pro 400 prints documents upside down. This only happens when you print in black and white, and from certain applications. Files PDF and Word documents print very well, as plain txt files and files from my accounting software, but files CorelDraw and images in Photoshop CS5 reverse print.
If I saved a CorelDraw file in PDF format, it will print correctly, but not the native file of COR.
From Photoshop, it makes no difference what file format I print - jpeg, tif or even a file not saved - all printed reversed if I select black and white.
Colour printing is fine for all applications.
Like most of my needs to print b & w, I the printer defined as it as default and just change color when the need arises, but it means I lose lots of toner if I don't remember to print in color in CorelDraw or Photoshop. Printing an image to grayscale in color also gives the evil eye.
Any help appreciated.
Hello
Try to use a PCL5 driver, which is likely to solve such a.
First, open the control panel > devices and printers, right click on the printer and select printer properties.
Open the Ports tab, and take note of the path selected for the printer, and then close this dialog box.
Download and install the driver HP UPD PCL5, follow the installation by selecting the traditional model.
Follow the wizard of printwr indicated by selecting the same port as used by the original and complete its installation driver.
The UPD driver can be downloaded from the following link:
http://h20566.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=4157320&swItemId=ds_99378_6&swEnvOid=4158
Once you have finished, try to print using the HP Universal printing PCL 5 driver and check for the difference.
Please let me know if this can help,
Shlomi
-
HP Universal Print Driver for Windows PCL6 (64-bit) will only print black on Color LaserJet CP1518ni
Also, would like to have the complete software program to download rather than just the universal driver.
Hello @wyodude
Try this
Go to devices and printers and right click on printer properties then go to device settings and go almost all the way down to the type of device a color change and save the changes then go in the printer preferences and in the color tab, make sure that in its unaudited grayscale printing option
Maybe you are looking for
-
phone calls do not use the apple device
I get phone calls, saying: do not use your apple device, are these legitimate calls... I'm afraid that I'm a target? I recall once and they wanted me to hang on to my desk top (I have not)... I can't afford to mess up, so I just haven't used :-/
-
When I usually go on Yahoo Mail, I can click just the zone user ID and the ID information and password will like Firefox has that information already saved. This function ceased with the update for Firefox 24. Information ID and user password are alw
-
HP TouchSmart 15-j063cl digitizer ENVY
Hy.I have a TouchSmart from HP ENVY 15-j063cl with a glass of contact of borken. I would change it but I can't finde the number of spare parts. I need only the glass... Thank you!
-
Equipped with 64-bit Vista on Toshiba Satellite M305-S4848KB Can download updates but cannot install the Received error codes above for the updates listed above Clicked on "Get help with this error", but no error is listed among the choices Recommend
-
I got 1344 error during the installation of the software. The missing indicated messsagefile Data1.cab. I am running Windows 64 home premium.