LaserJet Pro m477fdw: incorrect country selected during the installation of the printer

Similar Questions

• LaserJet pro 1415CN torn/shredded paper in the printer. He can't get out

  Does anyone know how to get out the duplex unit? I can't remove paper that is now grated into the printer.

  Sorry, the duplexer does not come off this LaserJet. These printer types have the duplexer incorporated with the rear panel.

  It seems that it can come off, but it won't. He grated JAMMED paper or just lost inside the duplex unit? I asked because if it is loose and you want just outside, you can try canned air to spray the inside of the duplex unit.

• Don't vSphere replication create control points which can be selected during the failover?

  Don't vSphere replication create control points which can be selected during the failover?  Or is the latest version of replication, the only option to failover?

  Thank you

  -MattG

  No, this isn't

  You CAN do this with EMC RecoverPoint (although not on a per VM level).

• LaserJet Pro M477fdw: Use HP M477fdw toner... well work until the software update

  Printer was working fine with the HP - no toner this morning until he did an update of the firmware, just after a print job and now it says there is a memory color error. Call service center Tech says nothing that can be done. Is this true? The printer now allows any toner no HP to use? Altogether, this is BS. I get that it voids the warranty, but it shouldn't stop me to use what I want in the printer. This isn't a problem with the toner cartridges.

  Hello

  You can downgrade the firmware to the previous version in the tool below:

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=7326587&swItemId=t2_159844_1&swEnvOid=54

  Be sure not to interrupt the process until it ends on the screen of the printer and the PC.

  Kind regards

  Shlomi

• LaserJet Pro 400 M401n: How to set the margins for binding up and left for LaserJet Pro 400 M401n

  I am connected to ePremis (medical site) that allows me to print the selected medical forms. ePremis uses the default printer to print the selected form.  The selected form should be printed on a preprinted form that I load into the tray of the printer.

  The problem is that ePremis does not provide an option to set gutter margins and print aligns correctly with my pre-printed form. The print position is a little weak and must also be shifted a little to the left. I need to reduce the high binding margin to move the position of superior print on the page and the left binding margin must also be reduced to move the print a little position to the left so that the printed data will properly align with my pre-printed form.

  Since ePremis does not offer an option to set the margins of the gutter, I need to be able to set the margins of the gutter through the printer driver, but there is also no option provided by the printer driver dialog box to set the margins of the gutter.  :-(

  Is it possible to set the printer LaserJet Pro 400 gutter margins?  I see the margins left and right options in the driver dialog box printer, but they are grayed out and cannot be changed.

  I have another printer, Kyocera laser printer, and I don't have this problem with the Kyocera because it offers the possibility to set gutter margins in the printer driver dialog.  I wonder why the LaserJet Pro 400 does not provide this option?

  I perhaps could solve this problem by sending PCL6 commands to the printer before printing?  I'm a programmer and am open to this option if it would work.

  Your help would be much appreciated.  Thanks in advance!

  Setting margins generally depends on demand - but (you say) that your application does not allow this.

  Some printers provide functionality of saving images , whereby the position of the image of the page onto a physical sheet can be adjusted to the printer, usually on a basis of by-tray.

  For example, with my Laserjet Pro MFP color 400 M475dn, the appropriate menu/menu item is described as follows:

  

  Note:

  • This setting applies to the bar up this that changed, so will have an impact on all the tasks using the specified status bar.
  • Not all printers support these features - I have no idea if your LaserJet M401 exercises or not.

  With regard to the '... sending the commands to the printer before printing... PCL6«» :

  • PCL6 (PCL XL) rather more autonomous than PCL5is, so I'm pretty sure that nothing you can "send" to the device to influence the outcome of the following printing.
  • Even with PCL5 print jobs, standard printer drivers are "overcome and-tail' with universal output language (UEL) escape sequences (which reset the device to the market environment (user - default)), which would be too mount sequences exhaust specific PCL5 previously sent to the device.

• Cannot install roboform 7.9.8.5 in every night, does not allow the selection of Firefox to be selected during the installation. go to address?

  Windows 8.1 last Firefox, Roboform 7.9.8.5.
  During the installation of Roboform and selecting the browser to install it on the only browser which is selectable are IE, firefox and chrome are grey.

  33.0 Nightly of Firefox is a version of alpha 1 pre-release tester.
  Check with Roboform to see if they take over the alpha or beta of Firefox versions.

• HP LaserJet Pro MFP M125-M126: cannot set the default printer

  Hello

  We have HP LaserJet Pro M125 - M126 PCLmS network MFP all in one printer, as the installation of all users was a success and was working fine the day of installation, after a day all users face the question cannot set default pritner, cannot print, all users are faced with question at a time ,

  quick response is appreciated,

  Hi @darshan9 ,

  I see that you have problems affecting the default printer for users and you cannot print over the network.
  I'd love to help you.

  Do you mean the configuration of individual computers with the printer on the network users, or a computer with multiple users?

  You have administrative rights on the computer to make changes?

  What is the name and the product number of your printer? How can I find my model number or product number?

  Download and run the Print and Scan doctor. It will diagnose the problem and could solve it automatically. http://www.hp.com/go/tools > using HP diagnostic tools for printers under Windows HP.

  I suggest you to check if you have another account user or an administrative account.

  I also suggest to create a new user account and check if you are able to set the default printer.

  Create a user account. Create a user account.

  If you're still having problems, run the Fixit tool. Diagnose and automatically fix problems printing and printer.

  What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  If there is anything else I can help you, let me know.

  Good day!
  Thank you.

• LaserJet Pro M127fn - failed to get on the network MFP

  I'm the wired network, but config report shows the ip address is 0.0.0.0. With the help of Windows 10. What ip address to use?

  Hi @kckeene117,

  I see that you are having problems, install the printer on a wired network. I will definitely do my best to help you.

  When the ethernet cable is connected to the printer and the router, the router is supposed to send an IP address to the printer automatically. (192.168...)

  Power cycle the router and restart the computer and the printer. You may need to try a different port on the router or another ethernet cable if you have not found an IP address. Check the connections at the back of the printer.

  Do you have Mac filtering on the router?

  What type of network setup you have and what is the brand name? (modem/router, router, switch)

  Check if you have a valid IP address.

  Here is a document to set up the printer on the network.

  Configure the printer to a wireless or wired network for the HP LaserJet Pro MFP M125, M126, M127, Color LaserJet MFP M176 Pro and and M177 Printer series.

  If you appreciate my efforts, please click on the "Thumbs up" button below.

  If you have any questions, please let me know what steps you have taken and the results. Thank you.

• Windows XP Pro can't find HD during the startup of the CD process.

  Lately, when my computer starts, it began to automatically run the disk check process. During the process, several files are either deleted or recovered. It's embarrassing so I tried to repair Windows XP Pro OS. The problem is that Windows does not detect the drives. I tried the ASR system, the R option to repair, and continues even with the start of the CD but Windows reports it cannot locate my hard drives. My motherboard is GA-81955 X Royal Gigibyte with 2 IDE hard drives of 40G and 2 DVD/CD players. Thanks for any help.

  The problem is in the AVG Antivirus software that I had to uninstall and remove all references to it in the registry. With no antivirus on the computer software, everything worked fine.

  Then, recently, there was an automatic update of Windows that enamored System32 of the computer records. Due the Gigibyte motherboard and how second HDD and DVD/CD player were to be installed to operate Windows has not found any drive C.

  To get the C drive to work again I had to remove it and install it in another computer as a slave drive XP then manually restore the files of System32. The restored files are not the same that have caused other problems. I tried to reinstall only the C drive and 1 DVD/CD drive but windows still not able to perform automatic recovery. Spent several weeks to correct the problems and reinstalling the software.

  The best solution would have been to reformat the C drive and reinstall the software, but I didn't know if I had backed up all my data.

• HP LaserJet Pro M1536dnf MFP: Inaccessible Scanner for the HP LaserJet Pro M1536dnf MFP

  Problem:    When I try to scan a document I get the following error: (see screenshot below)

  "Scanner inaccessible.... Scanner communication cannot be established. Make sure that your product is powered, check it out connection and ensure that your network is working properly. If these conditions are correct, restart the product and try to scan the image. If you are running a software firewall, it can block scan communication. Please visit www.hp.com/go/wirelessprinting for help to configure your firewall. »

  

  Shortly before this error message appears the scan on the printer function active (i.e. the scan head heats up and moves on the glass while kindled) , but no preview picture ever, only the error message. This error has just occurred within the last few weeks and before the scanner and printer worked flawlessly, although I'm not sure what happens if something changed to cause the problem. Printing features appear to be affected and functioning properly.

  Background:     
  (1) I use a HP LaserJet Pro M1536dnf multifunction printer (product #: CE538A), fax, scanner, copier.

  (2) my OS is a Windows 7 Home Premium SP1 64 bit.

  (3) I also run Norton 360 first worm 21.7.0.11 and System Mechanic Professional worm 14.5. Disabling the Norton 360 Firewall has no impact and I get the same error "scanner inaccessible."

  (4) the computer and printer are both connected by ethernet cable to my wireless router. My router is a NETGEAR R7500-100NAS. I bought and installed yesterday thinking that my scanning error was due to a bad router. This new wireless router has had no effect on fixing my mistake 'inaccessible scanner. The error is the same today as it was before the new router.

  (5) I ran recently updated HP and no new update is available, all windows updates are installed.

  (6) I tried to uninstall and reistalling the full version of the driver without change, I still get the same error.

  7A) when I run HP Print and Scan Doctor 4.6, most of the time, it shows that all controls the scanner, all green checkmarks, are indicated next to Device Manager, the device status, Windows (WIA) Scan, HP Scanner Twain and HP Scan (see screenshot below)

  

  but then, when I try a test analysis, the "inaccessible Scanner...". Communication of the scanner' error occurs.

  7 (b) other times, when I run HP Print and Scan Doctor 4.6, it shows: (see screenshot below)
  Error of scanning of Windows (WIA): the tool has detected a problem with scanning software (WIA]. Remove the software by clicking 'uninstall '. Reinstall the software with t he product CD or by downloading the software full of the latest features of (recommended) HP customer care.

  

  (8) all other aspects of the printer are working very well to my knowledge (it prints and copies without error).

  (9) I am able to view the IP address of my printer in my Internet browser, but there is no available for me WebScan functionality sweep as a workaround.

  Question:

  What can I do to fix the function scan from my printer that worked flawlessly just a few weeks ago? Any help would be greatly appreciated I'm full of ideas on what is wrong or how to fix it. Thank you!

  -Eric

  Hey @Eric_Bucktown,

  Thank you a lot to get back to me regarding this conflict of scanning. Also, thank you for all of the details that you have included in your messages. It is the first time I've heard talk of Mindspark or other spyware cause conflicts of scan. I'll have to remember to have others perform these steps in the future should similar questions arise. Controls only you need to run is the HP print and the tool of analysis of the doctor. It is designed to fix all possible system software driver and conflicts on the computer. However, as you can see, spyware and malware can sneak between the cracks.

  I brought this question to one of my colleagues who works with computers rather than printers. After I explained to him that you had made to solve this problem, it was suggested to keep your system in good working order and to avoid future conflicts of scan, you run the Malwarebytes Anti-Malware and SUPERAntiSpyware Free Edition once a month. Also, just to let you know, Malwarebytes Anti-Malware and SUPERAntiSpyware Free Edition software does not actively scan your system unless you use the complete edition of Malwarebytes for a cost. This means that the software does not always find the infected files and will only scans your system on a regular basis. If you use your computer frequently, you can perform analysis at the same time a couple of months, and not once a month.

  If you encounter any problems in the future, please don't hesitate to reach out for support on the Forums of HP's Support. It was a pleasure to work with you! Good day.

• LaserJet Pro M1217nfw booting is not after the firmware update

  Hello

  My configuration:

  HP LaserJet Pro M1217nfw (USB connection)

  MacBook Pro (mid-2012) running OS X Lion 10.7.5

  My Odyssey:

  The HP scanning software included on the CD is rudimentary to say the least. In particular, it don't will not let me scan multiple pages and combine them into a single PDF file.

  Tried to scan printing & scanning with ImageCapture, an excerpt, and the pane in system preferences: they see any of the MFP.

  Uninstalled HP, reset printing system software, downloaded and installed http://support.apple.com/kb/DL907 according to the instructions on http://h30434.www3.hp.com/t5/Printer-Networking-and-Wireless/Mac-Lion-Scanning-Multiple-Docs/m-p/159... no luck.

  Downloaded and installed the latest HP software http://ftp.hp.com/pub/softlib/software12/COL32660/Im-80903-6/LJM1130_M1210_MFP_Full_Solution.dmg

  Installation goes OK, then asked the installer to update the firmware of the printer and I foolishly said yes.

  Result: the printer will not be in service longer. At the start, it displays "then to initialize... "with the Green (ready) and amber (caution) of fires, then LCD turns off, then"initializing... ". "all over again, to infinity. Needless to say that the HP software or the Firmware utility see the device more and in system preferences, it is listed as "offline". In a Word, it is bricked.

  Of course, I could use some good advice. Thanks in advance.

  Solution in another thread:

  http://h30434.www3.HP.com/T5/Mac-printing-and-scanning/LaserJet-Pro-M1217nfw-non-functional-after-firmware-upgrade/m-p/2323767#M36922

• LaserJet MFP M477fdw Pro: LaserJet Pro M477fdw MFP - cannot sweep off-grid PC

  Oh please can anyone help? Spent 3 hours on the phone today, a refund 2 with tech, the rest of the post sales and pre-sales who was supposed to be calling me back with a list of printers that can do what I need, but all first does not, so I called again and she promised that she would appeal before s/n and still did not! Massively unproductive day. OK rant over.

  So I bought the above and it does everything I need IF I want to rise to the printer and scanner as a pdf for printing. My old 8600 OfficeJetPro I stood there, chosen analysis, it would be as if scanning to PC / Email. / USB / Fax etc. I would say PC and scanned and sent to my PC folder on dropbox and open the pdf file automatically.

  The LaserJet printer seems no analysis like that, unless it is connected to a network folder, which tech was able to put in place. He wants only to use Windows fax and scan, which is a JPEG - no good for me.

  It may not really be so complicated and I'm sure it's possible. I tried uninstalling etc and all the drivers on the HP site but nothing worked.

  Can someone help me?

  Glenda

  Hi Glenda,

  HP Laserjet printers don't offer direct scanning to a computer like HP inkjet supply, scan to a computer can only be done by HP itself scanning software and not by the front panel of the printer.

  You can find the manual to the user below, any method of scan supported is listed (see Scan page v):

  http://h20628.www2.HP.com/km-ext/kmcsdirect/emr_na-c04636804-2.PDF

  You can go the HP from your PC only software from the Control Panel before you can only scan to a USB Flash drive, a shared network folder, a mail server, two emails or folder scan network are available for network connected device.

  Kind regards

  Shlomi

• HP Laserjet Pro 1102w: HP 1102w cannot detect the network.

  When you try to install my HP 1102w for wireless through my Motorola modem/router printing the printer is unable to detect the network.  The network on the printer light continues to Flash blue, indicating that it is looking for the network.  I have other devices connected to the router and all work perfectly.

  Counsel pertaining to this matter is greatly appeciated.

  Thank you

  cbs117

  Hey @cbs117,

  Welcome to the Forums of HP Support!

  I see that you experience some problems with your Laserjet P1102w printer connection to your wireless network. I can help you with that.

  To start, make sure that the printer is plugged directly into a wall outlet, not a surge protector. Once done:

  1. Turn the printer off.
  2. While the printer is turned off, disconnect the power cable from the back of the router for a minute.
  3. When the lights come back on the router, turn on the printer.

  Now if the blue light is not solid, the next step is to run the HP installation by clicking on the icon on your PC with a name similar to the Laserjet P1100 series. If you do not have this icon, download the latest drivers at this link.

  Please let me know if you are able to connect the printer after you follow the above. If you are, click on accept solution. If you appreciate my help, please click on the thumbs up icon. The two icons are below this post.

• Premiere Pro is not audio tracks during the ingestion of MP4 video files?

  Everyone runs into a problem importing files .mp4 in Adobe Premiere Pro, in which only the video but not the audio tracks are imported?  Searching the Internet, I see that I am not alone with this problem.  Isn't Adobe Premiere Pro can correctly handle files video .mp4?

  Thank you

  JC

  Well Yes, that's apparently the case. Note 3 was not the problem. It's the fact that the app Android cinema FV-5 recorded the track audio in mono AMR, which is a rate very low bit QuickTime, mono audio format. Where, however, the application is set correctly to record audio to AAC - LC format, first Pro CC has no problems ingesting the blow to both video and audio on the smartphone.

  Thank you very much for your help with this.

  Best,

  JC

• Make a visible selection during the withdrawal in a drop-down list

  Good day all.

  I am putting together a form where I have a drop-down list that contains 3 choices. When one of these choices is selected in the drop-down list, a table becomes visible to the user to fill out.

  The question I have is when the user selects in the drop-down menu, the table is not visible unless the user clicks in the fall down once again.

  I tried an event ' click and exit "and came with the same question.

  Here is the code I use. I would appreciate help with this.

  Chomp

  if (this.rawValue == '5') { }

  term_select. Presence = 'visible';

  }

  if (this.rawValue ! = '5') { }

  term_select. Presence = 'hidden';

  }

  if (this.rawValue == '6') { }

  temp_select. Presence = 'visible';

  }

  if (this.rawValue ! = '6') { }

  temp_select. Presence = 'hidden';

  }

  if (this.rawValue == '7') { }

  act_select. Presence = 'visible';

  }

  if (this.rawValue ! = '7') { }

  act_select. Presence = 'hidden';

  }

  You must use xfa.event.newText to get the selected value.

  The change event:

  var newValue = this.boundItem(xfa.event.newText);
  
  if (newValue == "5") {
      term_select.presence = "visible";
  }
  
  //etc.