Lenovo USB 500 GB hard drive not Accessible?

Similar Questions

• Western digital external USB 2.0 500 GB hard drive not recognized by Windows 7 Explorer. How can I fix it? ___Thank you for your help.

  The hard drive worked well until KB2398632 & KB2347290 updates have been downloaded and installed on 16/09/10.  Hard drive works fine on my Vista machine at work.

  On my own machine (Windows 7), the drive is seen in my BIOS.  He also appeared in the "features and properties" of the control panel Windows 7 and the 'properties' indicates that the device is functioning properly.  The pilot is also updated.

  It does not appear in the Windows 7 Explorer under 'computer '. Only the C: drive is indicated.

  My AMD South Bridge set drivers are up to date my USB 3.0 being drivers.

  Western Digital 500 GB external hard drive is several years old.

  two updates have no effect to detect the hardware. It was an IE and and update printer spooler. Remove it from the Device Manager and plug it into another USB port. "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/

• Extermal Toshiba USB 320 GB HARD drive not recognized correctly

  My hard drive does not recognize now them itself as a hard drive just an AT2P RC42 Cypress and is now useless after a few months in use.

  I uninstalled and reinstalled by the Device Manager. I then tried on another computer and I have the same problem, so it's the hard drive and not on the computer.

  It's an external drive USB 320 GB toshiba that previously worked fine, but now think its thing and nothing else.

  What can I do to fix this problem? Please help all my data on this drive...

  Hello

  Check it please this http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=17412 topic. You will find similar discussions.

• HARD drive not accessible

  I have two hard drives (C: and E :) on my computer. E: has been used as a backup. I now use an external HD for backup. When I re-formatted E: it shows the disc to be full when I check its properties. When I try to open Explorer or e: a window opens stating "E:\ is not accessible. The parameter is incorrect. "How can I get this back to a usable HARD drive? Thank you

  Hello

  I suggest you follow the steps mentioned below.

  Method 1:

  I suggest you run the clean command. Follow the steps mentioned below.

  a. Click Start and type cmd in the start search box and right-click on the cmd present in the menu.

  b. click on run as administrator.

  c. type the following commands as follows.

  DiskPart

  List disk

  Select disk 1 (if disk 1 is E :)

  Clean

  Note: Be careful while selecting the disc as it might format the other disk instead of e: take note of the size, and then check the size in the command prompt and then wipe the drive.

  d. check if you are able to recover the system.

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• LaCie 500 GB hard drive not detected on win7

  It has detected the hardrive but when I try to open it he asks me to format it 1st and this is just one month back what happens. Yes he detected before then I uninstalled win7 and installed ubuntu it detected it so I uninstalled ubuntu and installed win 7 and when I plugged the usb drive it displays me the icon in my computer however its not accessible and cannot be opened...

  Using BitLocker encryption applied?

  This is very interesting topic.

  I just found some other threads that might help:
  http://social.answers.Microsoft.com/forums/en/vistarepair/thread/4e153784-3217-4425-9c39-48030af82a13
  http://social.answers.Microsoft.com/forums/en-us/w7hardware/thread/a3e7548d-D16B-468F-A23D-6cfb1255544f
  http://social.answers.Microsoft.com/forums/en-us/vistahardware/thread/4491349a-FF75-4B31-97EE-6900c48908f8

  http://Forum.thewindowsclub.com/Windows-7-management-support/28674-how-disable-you-need-format-disk-drive-z-before-you-can-use.html (This can be recommended).

  Check all, but the last of them is recommended. Itknowledge24.com

  Still doesn't help me a lot.

• Satellite A200-28R - new 500 GB HARD drive not recognized

  Hi all!

  The BIOS cannot recognize my new 500 GB SATA HARD drive. When I connect it to the laptop, BIOS says "No device" in the drive options. Tried jumper allows you to change the interface of disc HARD SATA-1, but without effect.
  How can I force the BIOS to recognize?

  Toshiba Satellite A200-28R
  BIOS version: Phoenix v.2.60 for Vista
  HARD drive: Seagate 500 GB 7200 RPM SATA

  BTW: my old 250 GB HDD works fine

  Hello

  Have you tried the drive in another computer?

  Maybe your new drive HARD isn t working properly or defective so use another rnotebook to test it or request a replacement HARD drive.

• NAS hard drive not accessible more: the device is not configured to accept connections on port 'files and printers sharing (SMB).

  Dear,

  I am desperately looking for a solution for my specific problem how access my NAS.

  I have a hard drive from Western Digital NAS (Book Live) which worked fine until now. Yet, I just changed my internet provider and I now have a new Fritzbox 6360. Now, I can not access the hard disk of the commune of programs in Windows. I contacted two suppliers already, but without success. I think I have some incorrect settings in my Windows 7, 64 bit. This is the situation:

  -NAS is still working with my old Fritzbox, for testing that I went back-> ok

  -I can access the NAS via the dashboard or a TwonkyServer-> ok

  -When I access it via Windows Explorer, I wonder is to give my credentials (which don't work) or I get the error message: the device is not configured to accept connections on port 'files and printers sharing (SMB).

  -J' changed my IP address (dynamic even static) and connections, password-> without success.

  -J' tried SFC with the result that found no violation of integrity. -> ok.

  Any idea?

  Can you please turn off the NAS, unplug the cable and Ethernet cable? Wait about 2 minutes then plug all the cables back in. Any security program or firewall to this computer? Try disabling it for now.

  You have another PC or laptop which has Windows 7/8 and try to access the NAS?

  You have a smartphone or a Tablet and download an application for the WD NAS and then try to access files.

• I have the model of macbook air 2016 with i5 Professor and 8 GB ram... since it's the fastest ssd, but I have not seen all speeds up to now, I want to say is bcz I need to have usb 3.0 USB key or hard drive to see the speed of the ssd to usb 2.0 will work

  I have the model of macbook air 2016 with i5 Professor and 8 GB ram... since it's the fastest ssd, but I have not seen all speeds up to now, I want to say is bcz I need to have usb 3.0 USB key or hard drive to see the speed of the ssd to usb 2.0 will work

  What do you mean, your message is not clear.

• Qosmio G30 - RAID may not reflect new 500 GB HARD drive

  I have installed 2 new identical 500 GB hard in my Qosmio G30 with Windows XP.

  The system works well, but the disc cannot be mirrored. Report of the Raid Controller is 'Normal Operation status.

  This disk cannot be used for mirroring because it is outside the management of the RAID."

  Who can tell me whether it is a disc error or is the drive of 500 GB to big for the toshiba with Windows XP raid controller?

  > Can anyone tell me if it of a disc error, or is the drive of 500 GB to big for the toshiba with Windows XP raid controller?

  Hmm. I m not very good, but it could be possible that the 500 GB HARD drive is too big for the mirroring of the mode.

  But have you tried to change the mode in comforter Toshiba RAID you might find in Toshiba Assist-> Protect Fix & -> RAID Console

  Check if you can switch to the mirroring.

  By the way; RAID-1 is defined in the BIOS?
  Usually, when you use RAID-1 configuration, the RAID is set to mirroring. In this case, the operating system recognizes the reduced ability to both hard drives (in your case, it is not important since you are using the two 500 GB HDD).

  Check it!

• Desktop PC's processor HP 251 - a11, Windows 10, AMD quad core A6-6310 accelerated with 4 GB memory DDR3 system and 500 GB hard drive. I installed I tunes last version and cannot operate.  Error message says Hello not activated.  Tells me to

  Desktop PC's processor HP 251 - a11, Windows 10, AMD quad core A6-6310 accelerated with 4 GB memory DDR3 system and 500 GB hard drive. I installed I tunes last version and cannot operate.  Error message says Hello not activated.  Tells me to go to the Control Panel then administrative tools and allow to Hello.  I followed these instructions, but I can't activate Hello.  What did wrong and how I can activate the Hello?  My email is * any help is greatly appreciated

  < email published by host >

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• Is it possible to change the 500 GB HARD drive with an SSD on my HP Pavilion MS228sc?

  I wonder if it is possible to change the 500 GB HARD drive with an SSD on my HP Pavilion MS228sc?

  If 'yes', I guess I have to go for a SATA SSD if there is. But I have to worry about other specs?

  If 'Yes'... what could be.

  I googled my question but no answers... so I ty Wizzards :-) Forum

  @Lord_Nikon

  In fact, this is not true. As long as he uses a large SSD enough it will be able to use the recovery media. I suggest using a SSD of 256 or 512 GB if budgeted for the upgrade...

  He doesn't have to make a Windows 7 installation USB drive and use the activation key license on the certificate of authenticity from the PC Windows to perform a cleanup to install.

  One of them should be on your PC. The Prodct key is what is needed for installation and activation online.

  

• Hard drive not detected 50% of the time to start up

  I have a model of Macbook Pro mid 2012 with the following changes:

  • Upgrade to 16 GB Ram
  • DVD player, replaced by Bay and old (existing) 500 GB hard drive for storage
  • Hard drive replaced with 250 GB SSD (Samsung EVO 850)
  • Windows via Bootcamp 10
  • Mac OS X Yosemite
  • Refind installed at startup

  Recently, my existing SSD drive gave me a lot of questions - so I'm a new and SuperDuper'ed the existing on it. Formatted the Windows partition and reinstalled Windows 10.

  I have 50 GB on the Mac drive and 200 concerts on Windows.

  The issue that I am facing is that on every other bootup, the Mac does not detect the hard drive.

  If I OPTION-press and hold the button, I see only the 500 Gig data drive (which is not bootable).

  Then, I need to restart and COMMAND + R (or D) to enter the internet recovery mode, wait until the choice of network is displayed.

  Then when I reboot, I am presented with the original hard drive and multiple start options (Mac / Windows) on Refind.

  I don't think it's a matter of refind, as happens even with uninstalled Refind.

  This does not happen when I plug my old (SSD by default).

  What could go wrong on the new hard drive and I can barely turn the question?

  Thank you.

  What are the contents of the disc in hand and Optibay Bay?

• Toshiba 320 GB USB 2.0 HARD drive freezes computer

  I just bought a Toshiba 320 GB USB 2.0 HARD drive and every time I try to transfer the data of light go red after 20 seconds and the computer crashes. The only way I can sort is by turning it off at the wall. The HARD drive works fine via a USB1.0 port and other devices like printers etc joysticks work fine through my USB 2.0 Pci card, but not my HARD drive, any ideas what this could be?
  Thank you

  Hello

  You can also try to use the USB1.0 port. But if you want to use data transfer high, you can try to use the firewire port. Using Firewire USB2 adapter for example.

• Hard drive not found - installing WXP on Equium P200

  Dear all

  I have an Equium P200 with Vista. I decided to remove vista and install windows XP. I put the XP and it goes through a verification process, I guess. At the end of the audit and after I pressed the button to install XP, I get the message "hard drive not found on this computer. Help me with as I want to install XP, my laptop?

  Concerning
  REDA

  The XP operating system could not find the HARD drive because you have not installed the Intel Matrix Storage Manager.
  It is a SATA driver is needed t install the XP.

  During the operating system installation process, you will need to press the F6 key to include the external USB FDD drive SATA driver.

  It you don t have a USB FDD drive then nLite software could be a solution.

  PS; Search this forum for similar topics, because this has already been asked several times

• Hard drive not detected after adding 2nd mSATA SSD for HP Envy 14 1002tx

  Hello

  I'm having a problem when adding an extra mSATA SSD for my HP Envy 1002tx model.

  The laptop comes with a 500 GB HARD drive and I see that there is a 2.5 "mSATA SSD slot under the HARD drive, so I bought the same type of SSD and installed it but when I turn on the laptop, it does not introduce yourself. I don't know why?

  I want to have an SSD for boot up the laptop and HARD drive to store animals.

  If anyone knows if there is any software I have to install in order for the laptop to recognize the SSD?

  OR

  Is - this material is defective?

  Thank you in advance!

  Sings,

  Precious wrote:

  pepe999 wrote:

  Remove the hard drive and try to start only with the mSATA SSD.

  Did this and it showed "No. Bootable Device Insert boot disk and press any key"

  I'm really sorry, I could not find this before, but the slot under the hard drive is not compatible with the mSATA disks. It's for WWAN modules! Your laptop is not like 4 I thought, but Envy 14 equipped with the first generation of Intel processors. Envy 14-Sandy Bridge 2000 series could be BIOS modded to make the miniPCI-e interface works with the mSATA disks but Envy 14-1000 series is not possible to change.

  Edit: 2.5 "drive 256GB solid state drive is listed as compatible.