Level of security by default RV180

Similar Questions

• Easy VPN setup with interface to multiples with the same level of security

  Hello

  I want to configure an ASA 5505 with 7.2 (4) software and dual license ISP and when I configure two interfaces with the level 0 on two security interfaces and enable vpnclient the trace message appear:

  ERROR: Cannot determine the internal and external interfaces Easy VPN remote: multiple interfaces with the same levels of security.

  vpnlclient of configuration above:

  vpnclient Server x.x.x.x where x.x.x.x
  vpnclient mode network-extension-mode
  vpnclient nem-st-autoconnect
  vpnclient TUNNEL_EZVPN_TUNNELSPEC vpngroup password *.
  vpnclient username usr_ezvpn_tunnelspec password *.
  vpnclient enable

  interfaces:

  interface Vlan200
  nameif outside1
  security-level 0
  IP x.x.x.x 255.255.255.252
  !
  interface Vlan300
  nameif outside2
  security-level 1
  IP x.x.x.x 255.255.255.128
  !

  monitor the SLA to the routing:

  monitor SLA 100
  type echo protocol ipIcmpEcho 200.221.2.45 interface outside1
  NUM-package of 5
  frequency 30
  monitor als 100 calendar life never start-time now
  ALS 200 monitor
  type echo protocol ipIcmpEcho 200.154.56.80 interface outside2
  NUM-package of 5
  frequency 30
  Annex monitor SLA 200 life never start-time now
  ALS 300 monitor
  type echo protocol ipIcmpEcho 4.2.2.1 interface outside1
  NUM-package of 5
  frequency 30
  Annex monitor SLA 300 life never start-time now
  ALS 400 monitor
  type echo protocol ipIcmpEcho 200.244.168.149 interface outside1
  NUM-package of 5
  Timeout 3000
  threshold of 3000
  frequency 30
  Annex monitor SLA 400 life never start-time now

  Follow-up:

  !
  track 1 rtr 400 accessibility
  !
  Track 2 rtr 200 accessibility
  !

  routes:

  Route 0.0.0.0 outside1 0.0.0.0 x.x.x.x 100 track 1
  Route 0.0.0.0 outside2 0.0.0.0 x.x.x.x 200 track 2

  The track works normal.

  Kind regards!

  Try using the command "backup interface" on the secondary ISP interface.

  http://www.Cisco.com/en/us/docs/security/ASA/asa72/command/reference/b_72.html#wp1338585

  You need to increase the level of security to 1 for this interface.

  By default, EasyVPN uses the highest level of safety inside and the lowest outside.  Anything between the two must be set manually.  I assume you have an interior vlan defined but not added to the posted config.

• Users and levels of security in the client of the lookout

  I would like to setup users with different levels of security in my client application of Lookout 6.7. When I try to add a user, I get an error message that says "add user operation failed. See system drive disk space» There are a lot of disk space, 50GB. Is it possible to have the users connect to the client with different levels of security?

  Thank you

  Brad Adams

  Communications Group Inc.

  Launch Manager users in administrator mode

  C:\Program Files (x 86) \National Instruments\Shared\Logos

  Right-click "usrmgr.exe", select run as administrator

• Levels of security ASA Firewall interface and access lists

  Hello

  I am trying to understand the correlation between the ACL and the levels of security on an ASA of the interface.

  I work with an ASA using both! ??

  Is this possible?

  Assumptions: Any ACL applied below is on the wire of transmission (interface) only in the inbound direction.

  Scenario 1

  interface level high security to security level low interface.

  No ACLs = passes as I hope

  What happens if there is an ACL refusing a test package in the above scenario?

  Scenario 2

  Low security to high

  No traffic = ACL will not pass as I hope

  What happens if there is an ACL that allows the trial above package.

  I have trawled through documentation on the web site and cannot find examples, including the two (using ACL in conjunction with security levels).

  Thank you in advance for any help offered.

  Levels of security on the interfaces on the SAA are to define how much you agree with the traffic from this interface.  Level 100 is the most reliable and 0 is least reliable.  Some people will use a DMZ 50 because trust you him so of internet traffic, but less traffic then internal.

  That's how I look at the levels of security:

  A security level of 1 to 99 always two implicit ACL.  To allow traffic down interfaces of security and the right to refuse traffic toward higher level security interfaces.  100 has a security level IP implicitly allowed a full and level 0 has implicit deny ip any one.

  In scenario 1, if you apply an ACL to deny a security level of 1-99, it will eliminate implicit permit than an entire intellectual property and deny traffic based on the ACL and all traffic.  You create an ACL to allow some other desired traffic.  If this ACL is applied to a security level of 100, he'll refuse essentially all traffic because it will remove the authorization implicit ip any any ACL.  Once again, you will need to create an another ACL to allow traffic.

  In scenario 2, if you apply a permit ACL to an interface of level 0 of security, it will allow that traffic, but continue to deny all other traffic.  However, if the security level is 1-100, it will be all traffic to that destination and remove the implicit ACL (permit and deny)

• What level of security is the best in the OSI model, which is the application level?

  Hello

  I'm curious to know what level of the model OSI protects best against pirates, which is the application level?

  Thank you

  Johan

  Hello Johan,.

  The OSI networking reference model (ISO 7498 - 1) is designed around seven layers arranged in a stack.

  The OSI security reference model architecture (ISO 7498-2) is also designed around seven layers, reflecting a high level of different requirements in the security of the network.

  In the OSI model, each layer has its own functionality and according to which it has features of different security as shown below.

  Application - authentication

  Presentation - access control

  Session - non-repudiation

  Transport - the integrity of the data

  Network - Privacy

  Data binding - insurance / availability

  Physics - certification / Signature

• I need to restore the security permissions default to all files on drive c of a Windows XP workstation

  I changed some security permissions on all of the C: drive, which is my boot drive system on a network under Windows XP Pro SP3 (32 bit) desktop.  I had shared the drive several years ago, and I believe that the problems were built from the other. I had to rebuild my server and choose a different domain name and connected workstations to the domain. I would like to restore default settings for the C: drive of the workstation (not shared?, permissions and security on all files of Windows and the default user restored to the default values.)

  Anyone know where I can find a list of the rights and permissions for each of the folders and subfolders on the WIndows system drive? Or is there an automated routine that will restore the default permission?

  Hi ArtMinds,

  Your Windows XP question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please ask your question in the Forums Pro Windows XP IT on Technet. You can follow the link to your question:

  http://social.technet.Microsoft.com/forums/en/category/windowsxpitpro

• question about the level of security at netwerk

  Hello

  safety of newterks and computers occur in the OSI model on the application level, or there are also security level nested, if so, who are?

  Thank you

  Johan

  Hello

  safety of newterks and computers occur in the OSI model on the application level, or there are also security level nested, if so, who are?

  Thank you

  Johan

  The seven layers of the OSI model defined and functions explained http://support.Microsoft.com/kb/103884/en-us

• Levels of security and access lists

  I have DMZ1 (security50) that needs to access DMZ2 (security20). However, for access to the work I need to modify the access list that controls access of DMZ1 inside (Security 100). My understanding is that you only need statements of access list for the access of low to high not top-to-bottom.

  I simply get it wrong?

  Andrew,

  In general what you say is true. That is how the PIX is designed. But, once you apply the acl on the security interface higher than its interior or the demilitarized zone, default behavior is no longer there. In this case, you must allow exclusively the superior traffic lower. So, it's flexibility as security engineer to check our our strictly secure LAN traffic. Although we know that the inside is always fixed, but an acl can be applied to control which traffic is allowed outside or dmz. Your case is a classic example of why you need a lower LCD of higher security interface.

  I hope this helps! Thank you

  Renault

• Applications and levels of under by default UI 5.6?'

  I thought that 5.6 would allow Applications and levels must be created in the default user interface or the custom user interface and then you can view the collection of either env?

  It seems that I can create a group of 'applications' in the default user interface, but not the application levels.  If I create a "pane App" group in default user interface and then create an 'app' group and try to associate the application layer to the app group, it won't let me.

  Also, if I create an application in the custom user interface is not visible as an application in the default user interface.

  -MattG

  It's the custom in the UI by default/vSphere groups are not related.  Your app in the custom user interface groups are not exposed in the user interface of vSphere.

• Level of security for the dashboard pages.

  Hi all
  
  
  I have a question. I want to apply security to the level of the data to the data in dashboard pages.
  
  
  
  All the answers.
  
  
  
  
  Thank you sunny.

  Hello
  Can do this by using the section level security.
  Place the x, y in a section and z report in the other section. Now apply security at the level of the article accordingly.

  Awarded points if the answer.

  Kind regards
  Srikanth

• Page not available due to security policy, default category, it's my homepage which has always been my home page.

  I don't not all of a sudden access to my home page - I get this message: "your page is blocked because of a security policy that prohibits access without the category. This is my homepage for years and I've never had this problem before.

  This is the home page that you use?
  Browser.Startup.homepage: http://www.goarch.org/

  Some added addons toolbar and anti-virus are known to cause
  Firefox issues. Disable all of them.

• Telepresence & ITL (security by default) endpoints

  Hi all

  CTS supports ITL? It is supported by the IP used by a few CENTS, but phones that all the CTS itself? Is it is supported, how you can delete the ITL to migrate between clusters CUCM CTS?

  Thank you!

  Hello

  The CTS codecs use not an ITL, only a CTL if the call manager cluster is running in mixed mode. You can check if a CTL is installed by connecting to the CLI and by running the following command:
  See the security trustlist

  HTH

  Manish

• Security code default from blackBerry to Blackberry Bold 9700 Smartphones

  I bought a blackberry Bold 9700, but don't forget to ask for non-safety for the device code/PIN. Please can someone tell me what it is. Thank you

  OK, and once again, it depends.

  If you are on a corporate BES account, your employer's it policy on the device could prevent you to change the password.

  If it's your own device on a personal account, Options > security or Options > password. The actual location may vary depending on the version of the OS on the BlackBerry.

  That aid is the information you need?

• Highest level of security wireless Photosmart D7460

  Hello

  I'm trying to secure my network and I need to know that the highest safety standards supported on this device.

  Thank you!

  According to the Manual it is WPA - AES.

• Passing the credentials of security for default AIA policies

  We use a single server for development and an area clustered with a for testing external hardware load balancer. We have faced the problem during the migration of single server domain to the domain in cluster. Area of single server, call the basics-the author of the composite adapter read request (or communication between all composites also) didn't have all the identifications must be DISPATCHED, most likely because demand from the same server.
  In the cluster area, the request goes through the external load balancer and requests are failed by SOA server because there is no username/password attached name.
  As a solution, we put the username password in the adapter to read composite.xml and it market.
  

  <wsp:PolicyReference URI="oracle/wss_username_token_client_policy"
                             orawsp:category="security" orawsp:status="enabled"/>
        <property name="oracle.webservices.auth.username" type="xs:string"
                  many="false" override="may">testuser</property>
                  <property name="oracle.webservices.auth.password" type="xs:string"
                  many="false" override="may">testpassword</property>

  But we do not want to hardcode the name of user and password into composite files.
  I tried to create a key identification information in the EM console and using this key in the composite.xml, but it does not work. I could have missed a configuration. What I did was to create a new key identification information under: Weblogic Domain-> domain-> Security-> credentials-> oracle.aia.security-> identification news here (aia.authentication.credentials)
  Used the name of the new credential in the composite.xml like this:
  Right click on the link to the ABC partner applicant-> configure-> added political WS oracle/wss_username_token_client_policy under the Security tab
  Published additional policy:
  Name = LCR - key
  value = Basic.Credentials
  Replace value = aia.authentication.credentials
  
  With these settings it still does not. Any idea what to do?

  Please try with oracle.wsm.security instead of the card oracle.aia.security card