First problem elements 14 DVD burn

Similar Questions

• Some of the Menus Adobe Premiere element cause DVD burning failures?

  Some of the Adobe Menus cause DVD burning failures?   What should have been a project of 10 minutes for a small 4 minute video took hours as burning DVDs stopped at 4% and then gave a message of "something has prevented completion in progress DVD burning".  I could finally solve it down for the Menu template, and when an audio clip looping has been added.  The Menu was built for an audio clip loop, but when I removed it the fine burned DVD.

  Since my last post, I checked that my drivers are up to date.   Driver updates were made to the display card Intel HD 4600 Graphics and Chipset Intel 8 series/C220 family SATA AHCI Controller.

  I created a new project and changed the flow of work to remove the check mark from selection to 'Add Menu markers automatically for me'.   When the menu has been selected and displayed, only the main Menu was to confirm that I didn't remove the Menu scenes.   At this point, I finished the remaining workflow and tried to burn on DVD using the stated parameters previously.   However, it had the same failed result.

  I went then to the path of Premiere Elements menu bar: Edit > Preferences > General

  The option "use hardware acceleration (works on Intel HD Graphics 2000 and higher)" has been selected.  I unchecked this option and clicked on the OK"" button.   I then tried to burn DVD with DVD NTSC_Widescreen_Dolby preset.

  Success!   The DVD was burned and confirmed to work in older DVD player (AVCHD burning earlier disk did not work in older DVD player, but worked in a new Blu - Ray player).

  It seems that the "use hardware acceleration" option preferred default was the problem in the prevention of burning DVDs.

  A.T. Romano thanks for your quick response and help to solve this problem.

• First 10 Elements: Menu DVD does not work on your stand alone player, file Open_DVD\Sources

  Hallo,

  I have prepared a project with Premiere elements 10 using video clips of 1440 * 1080 with some petite markers and menu structure. The structure of the DVD encoded has VIDEO_TS (as usual) and OpenDVD records which is new to me and that obvoisely contains important information.

  Read the DVD with Windows Media Center, everything is good. Using a stand allone player that the menu not played correctly, the proportions are not correct and there is no possible navigation. I tested the DVD in an electronic market with many players and found only one or two who have been able to read the DVD. My questions:

  How to build a DVD that consists only of the VIDEO_TS folder with all menu information included, and which is compatible with a standard DVD player? (what settings)

  What is OpenDVD folder?

  Thank you for your response, best regards

  Your project Preset should match your Source footage, as close as possible.

  If you go on a DVD, a workflow would be to import and edit your material anamorphic 1440 in a corresponding project. Then, once finished, / the share of exports in DV - AVI, create a new DV (DS) project, import this file DV - AVI inside and do what the authoring, then burn to disc for the DVD.

  Good luck

  Hunt

• DVD Maker does not recognize my DVD burner

  
  

  Not from files from digital camera with Windows Movie Maker, sent the draft to burn movie DVD Maker tells me "no DVD burner installed"...

  Dell PC, 2 GB of ram, only six months, Vista OS, no other software has problems with the DVD burner...

  Any ideas? Any help much appreciated...

  Hello Bladerunner.au,

  You could try the following:

  Fill any DVD burning software. These programs may be trying to use the player, which prevents access to the Windows disk. Programs to look at include:

  • Roxio product family
  • Power DVD
  • WinDVD
  • Direct Media
  • Windows Media Player
  • Nero Burning ROM

  Update the firmware on the optical drive and the BIOS of the computer. In some cases, the firmware of the drive may be damaged or the BIOS can 'lose' the reader. Visit the Dell drivers and downloads site Web and enter your Service tag to get the updates specific to your computer.

  Since you have a new Dell computer, you can go to the Dell site for the support of this new computer.
  www.support.Dell.com

  I hope this helps.

  Thank you

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Windows DVD burner stopped working

  whenever I try to burn a DVD with windows DVD burner I get a message saying a problem caused windows DVD burner to stop working, when we find a solution I will be notified, well it lasts for a year now, I even wiped my laptop and re-installed windows and I was able to burn 1 DVD until I started getting the same message Although I am sick this, and when I try to get technical support, I wonder how is interesting to me. WTF?  I wonder that Apple makes their customers in the same way, from what my friends me with MACs, if not why say they operate. Then said is I don't van not get help to solve this problem, I'll become another conversion from Apple...  It has been a year and still no solution? Come on.

  If Vista was preinstalled on your computer, you do not qualifty for the FREE Microsoft Support

  All support is the manufacturer of your computer.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Go to the website of the manufacturer of your computer/laptop > drivers and downloads Section > key in your model number > look for the latest Vista drivers > download/install them.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://Windows.Microsoft.com/en-us/Windows-Vista/burn-a-CD-or-DVD

  Burn a CD or DVD

  If your computer is equipped with a CD or DVD burner, you can copy files to a recordable disc. This process is calledburning a disc. By default, Windows Burns discs in the active file system format, but you can also choose to burn discs in ISO image format.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://Windows.Microsoft.com/en-us/Windows-Vista/which-CD-or-DVD-format-should-I-use

  Should which CD or DVD format I use?

  What format you use is determined by the computer that you will use to read the information that is recorded.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://Windows.Microsoft.com/en-us/Windows-Vista/disc-burning-frequently-asked-questions

  Disc burning: frequently asked questions

  Here are answers to some common questions about burning a disc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Microsoft.com/kb/982116/en-AU

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  See if the information above solves the problem.

  See you soon.

  Mick Murphy - Microsoft partner

• Satellite A135 - problem with the CD/DVD burner

  Hey guys,.
  A few days ago as nearly a week ago I had burned an audio CD for myself and it worked perfectly. Today when I tried to burn an image on my DVD, disaster. I use two software. IMGBURN & NERO. Unfortunately both failed me. What is happening is that the burning process starts normally, it shows that the buffering and burning taking place as well as caching of files. "Finally, it shows the burning process has been a success, but when it comes to verification, the drive appears saying: data verification failed - too many errors (Nero) and for IMGBURN it says ' they layouts do not match. When I reinsert the DVD, it shows that it is completely empty. Although both claim that the fire was successful. Later, I tried to burn a data dvd, still no luck, engraving, he shows successfully but verification fails and reinsert is empty.

  My laptop is: Satellite A135
  CD/DVDROM: TSST CORP TS-L632D ATA
  OS: Windows

  the default windows was vista when I bought it.

  Hello

  If you can't burn DVDs, then you should check first if it is a software problem based question or related equipment.

  I've been reading about the reader of CD/DVD burning questions and as many times the registry has been corrupted.
  Means that you was able to burn the DVD after you remove the upper and lower filters in the registry. Google for it and you'll find many pages.

  Is there a problem of CD/DVD drive, then you should find a good update on the page of European Toshiba driver in your laptop. If there is no update firmware, then it means that this firmware is ok and it s not necessary to date.

  Last but not Lea not all CD/DVD drive are compatible with all drives (CD and DVD).
  Why? Because the different CD and DVD manufacturers produce own using different standards. In this case, it may be possible that not all discs will be properly treated

  I had the same problem but might solve this problem by using TDK R CD or DVD

• DVD burning problem: I burn the movie on widescreen PAL on a DVD-R disc. I managed it burned without menu. Now, I've added a "Pan and Zoom" menu with a main marker at 00:00:00:00, 21 scene markers, and a stop at 01:29:32:17 (th

  DVD burning problem: I burn the movie on widescreen PAL on a DVD-R disc. I managed it burned without menu. I have now added a "Pan and Zoom" menu with a main marker at 00:00:00:00, 21 scene markers and a cleat to 01:29:32:17 (the end of the film). The combustion is interrupted with a message to watch a C:\Users\ianle_000\Documents\20151206160446.iso file. There is no file. The message also provides a link for an explanation. This Web page is impossible to obtain. I'm running on a PC with Windows 8.1.

  Thank you once again. I burned the DVD!

  It is the first film for which I have reached the stage of burning. I'm not sure why she didn't in the first place. I tried to burn the "no menu" version, but at the time, was shot the DVD itself - I wonder when he reached this point?

  So, I burned the "no menu" version to another DVD, that worked, then the version of menu, with no cleat to a third DVD, which reads perfectly.

  Now that I have a successful routine, I'll stick to it.

  Thanks for all your help.

  I'll close this discussion now.

• Portege A100 - problems recognizing a new DVD burner

  Hello

  I'm looking to replace the Panasonic/Matsu * player UJDA750 combo with a LiteOn SOSW - 852S DVD burner. The LiteOn is CSEL and is not recognized by the Portege A100. I tried to change the master/slave/CSEL and Inverse CSEL using E2MS_WIN_SOSW - 852 S .exe (in an Acer Travelmate 220, which sees all configurations), but the Portege A100 still does not recognize LiteOn.

  I ran IDEDIAG using a WinME boot CD and the Matsu * a Combo drive in Portege reports as secondary master. So, I tried flashing the drive LiteOn (using the Acer Travelmate platform) with MTKFlash version 183 c using the a command? "mtkflash 3 w/b PRS9.bin" (using the original firmware of saved), '3' to change the drive to the secondary master. I came across problems here - the flash appears to hang. The drive is always ok, however. I flashed it back to the original ok CSEL using E2MS program in Acer.

  I have not tried bridging the pins 45 to 47 on the LiteOn - I thought maybe it was a last resort.
  -Can help you with the correct configuration for a CD/DVD drive in the Portege A100? There are a bunch of different ones - primary, secondary, tertiary, Quarternary master/slave and CSEL and Inverse CSEL. Portege A100 'sees' the Matsu * a CDROM model CR-176_B of Acer.

  Or - can you recommend me a DVD burner for this laptop?

  Hello

  The evolution of the master/slave/c-salt settings is not recommended and tell the truth I put t know if its possible. I presume that it of not possible to Flash these settings on medium power.
  In my opinion it doesn't make any sense to do.
  This procedure may damage the drive. Maybe you will not be able to use this drive more and more you will void the warranty!

  I think it s better to buy a compatible device and supported as trying to drive not compatible flash.

  Did you check your user manual? Usually the user manual should provide information on compatible CD/DVD players and supported.

  Good bye

• Satellite P200 - 10 c with a problem of burning in the CD/DVD burner

  I have some problems with my DVD/CD-RW in my Toshiba P200 - 10 c (running Windows Vista Home Premium).

  When I try to burn a CD (audio or data), the software I use (listed below) shows me the progress of burning of 0% to 100% and at the end said "complete engraving process" or something like that, but * when the CD comes out (after burning) *, if I look at his face I see that it is really burnt, because I can see the area where data has been burned. But the problem seems to * when I insert the CD into the computer *, the laser of the CD/DVD-RW drive starts reading and reading and so on... made strange noises and finally, after some time, * windows detect the CD as a void (empty) CD *. And if I try to burn the CD again, the logger simply burn again on the latest burned data and so forth, for the third time, the fourth time...

  This problem only occurs when I try to burn a CD. If I try to burn a DVD, nothing is wrong, and the DVD is properly engraved.

  I already tried the following:

  -Burn a CD with NERO (version 7): same problem
  -Burn a CD with Toshiba CD creator: same problem
  -Burn a CD with MagicISO: same problem

  -Update the drivers (value package)

  -Try to play the CD in my computer (Toshiba laptop)
  -Try to play the CD on another computer
  -Try to play the CD in my audio player (with an audio CD and a MP3 data CD)
  and in all cases, the laser becomes simply crazy, you try to read the CD I burned my Toshiba laptop.

  ----
  I think (it's just what I think), the CD/DVD-RW burn the CD correctly, but do not burn the part of the disk called TOC (table of contents), I think. This is perhaps why the CD may not play in all devices... I think that devices cannot read anything at the beginning of the CD data
  ----

  Please help me... I don't know who do more...
  Need help... Anyone with the same problem?

  Hello

  Have you tried to burn data on blank CD using Vista option (do not use any other burning software)? I've done this several times and in my case works well. I have P200D.

• Satellite P300 19 p - CD/DVD burning problem

  Hi, I'm new to the forum and I hope somone will be able to help.

  I have DVD burning problems. When I use software engraving the image is usually copied ok and then the burning process starts, which usually lasts only a few moments, then the machine spits out the disc burnt and wasted.

  I usually use Corel DVD Copy 6, but have you tried TOSHIBA and other programs such as NERO. With the help of Corel VideoStudio, it burns discs with a success rate of 90%, but the problem comes when you try to copy my own created disks.

  I tried different types of discs (that is to say + R and - R), and I also tried burning speeds.

  Anbody else suffers from this problem?

  I have managed to find an error code 06077-26 - 2A 040902, made this average anyhting for anyone?

  TEMPRO alerts appear to have provided updates firmware for a number of other DVD players, but not for my machine? Maybe it's due a? All the drivers are up to date.

  Thanks for listening and the anybodies help is more than welcome.

  See you soon.

  In my opinion, you should not think about buying replacements. If you think that the drive does not properly contact service. If necessary the reader will be replaced free of charge.

• CD/DVD burner problems said that it is damaged or missing? Anyone has any ideas to help me solve this problem?

  Hello, I'm trying to fix my burner but I tried to uninstall and reboot my computer to see if the problem might be to set but he told me that my driver cd is missing or damaged, and I don't know what to do besides put my computer back to factory settings. So if anyone knows something I can do like that I don't have to put it back to factory settings it would be great.

  Remember - this is a public forum so never post private information such as numbers of mail or telephone!

  Ideas: My CD/DVD burner does not work and it is said that it is damaged or missing. How can I fix it?

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hello

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• DVD Burner problem

  I'm writing a DVD mastered with data. He is preparing to go, and then tells me "There was an error burning disc."  I then put in another disc and it never passes the validation errors entry screen. I bought another brand of DVD media and also a new DVD burner. I put the slow write speed as I can.

  Hello FarmBoy59,

  I suggest that you run the fixit by following the link below. This will automatically diagnose and repair problems with your CD or DVD drive when trying to read or burn media:

  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  If this does not work, I suggest that you follow the steps in the link below:

  http://support.Microsoft.com/kb/314060

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/) how to back up and restore the registry in Windows

  Thank you
  Irfan H, Engineer Support Microsoft Answers. Visit ourMicrosoft answers feedback Forum and let us know what you think.

• DVD burning problems

  I have a compaq presario cumputer with vista OS and it has oem cd burner - dvd - rom and the dvd software burning in it. Lately in trying to put a movie on a dvd disc it gets all the way to 99% and stops. Any type of information is even thrown the disk, what is and how do I do thanks.

  Hello bobo johnson,.

  You might want to look over the following information on DVD burning in Windows Vista.
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  There is also a KB article, that you can use to automatically fix problems burning DVDs in Vista. Click on the number to view the article.
  KB Article ID: 929461 -CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista

  If please reply back and let us know if you still need help.

  Sincerely,

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• DVD burned in first pro cc does not fill the screen. Desire a 4:3 aspect ratio

  I use first pro cc. I burned a dvd several times, trying different presets. Every time the dvd never fills the screen. It does not lool like box (16 x 9) letters. There is space around the photo / video. Need quick assistance, project is already late. Thanks in advance.

  Theo Smith

  Have you used one of the mpeg-2 DVD presets?

  Which one?

  MPE or Premiere Pro?

  Please show a screenshot of your output settings.

• After that the installation of first elements of dvd with the series nr.install 11 is interrupted and uninstalled

  After that installation first elements 11 DVD with the nr.install series is interrupted and uninstalled. What should do?

  Troubleshoot installation, http://helpx.adobe.com/photoshop-elements/kb/troubleshoot-installation-photoshop-elements-premiere.html