Licenses of telepresence

Similar Questions

• Telepresence - who ensure license on telepresence in VCS

  Hi guys,.

  I need to check the license of telepresence equipment reference in VCS, but I Don t have any experience on the VCS. That I can check this license on VCS. I know that models telepresence recording in CUCM and anothers in VCS.

  Thank you

  Wilson

  When you connect in the VCS, you can check the status on the landing page to see the use of the license. To see more specifically what licenses are installed, click the Maintenance > Options keys.

• License of telepresence screen

  Hello world

  As my topic above on the telepresence Server License screen,.

  I have several point endpoint entering CUCM 10.x as SIP:

  1 unit TX9000

  1 unit SX20

  6 units SX10

  How telepresence license screen I need so that all them endpoint can join the boardroom at the same time if the resolution for each endpoint that I need is HD 720 p 30 720 p 5 video content and?

  Please advise,

  Kind regards

  Ovindo

  Hi Ovindo,

  I would advise looking at the TPS date of issue of the graph that details license use screen beginning on page 20 to ensure you have the correct amount:

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/infrastructure/TS/...

  The TX9000 will use 1 and 1/2 license screen

  7 other units, 1 SX20 and SX10 6 would use 1/2 of a license of each

  -Jonathan

• Licenses on telepresence servers table in data sheet is not not to screen?

  I have deployed CUCM with driver version XC3.0.3 and vTPS (telepresence virtual server) version 4.1 (2.29).

  I made a model of the Conference on the driver to use HD 720 P 30 and content sharing 720 p 5.

  When I start a conference call with 2 endpoints VC I see 2 screen licenses are used, one for each endpoint.

  According to table 8 'telepresence screen of the license server by call for each Type of call' in the telepresence Server data sheet

  http://www.Cisco.com/c/en/us/products/collateral/conferencing/telepresen...

  Such resolutions should take license screen 1/2.

  Is this a bug or a configuration problem?

  If I call the Conference with audio only I see that no license used at all while the table indicated 1/52 of a license to screen will be used...

  You must be looking at the driver to see the actual number of resources on the server of telepresence.  The GST will report the number of screens are used, but driver will report the number of licenses of screen used for each call.

  See images attached to a test that I made just now with a GST which has only 3 licenses of the screen, but I'm able to connect up to 6 endpoints, each connected end point uses 1/2 a license of the screen.  The Conference model I use is set up similar to yours, but it has 720 p 5 active content.  Appeal of bandwidth is 1152 kbps.

• Telepresence Server / conductor

  I have a question about setting up locations and licenses on telepresence Server/conductor.

  In the lab guide, you can create a site with AD Hoc and conferences go to one location. This require two licenses of location?

  So you must put in place an MCU on telepresence BLAH ad hoc calls?  I use the telepresence server and conductor on VMware. It is connected to an IX5000.  Video calls go work with the three end points... but I can't have special video calls to work and that's really the question. I suspect that it's because I have only one license and the only defined place ad - hoc and configuration of Rendezvous.

  When I try and add the third endpoint video none of the video is active and the conductor was not aware of any current conference.

  Hope make sense

  Hello

  The ix5000 works in the same way that the CTS and make endpoints TX, she doesn't have the ability to promote a conference for a multimedia resource with a MRGL, only to make an audio call only and it fill in the call or the Conference on what it is. If you try to use it on a video endpoint it will join an audio only.

  An another endpoint that supports ad-hoc escalation as endpoints software TC can make climbing to the multimedia resource (conductor in this case) and bring the ix5000 to a conference.

  -Jonathan

• Join TMS MCU fails with "no ip bandwidth...". »

  We are trying to install a telepresence VTC system. We are trying to register the MCU (5320) (4.5) for TMS (14.6). We use a virtual VCS as the doorman. When attempting to add the TMS MCU, we get a warning "no bandwidth set to the system - system has bandwidth IP or ISDN bandwidth..." MSD displays zeros (0) for Ports and bandwidth. We have defined the bandwidth of the MCU on parameters of the H.323 MCU. There must be some little thing that we have not been configured correctly. We rechecked SNMP parameters, parameters H.323, etc. anything.

  Someone at - it have this problem before?

  TIA,

  Mark

  Areas are used in routing when creating the Conference schedules.  You can assign areas after adding points of termination or infrastructure in TMS, or while you are being added to them.  You can read more about which areas are in the TMS administration Guide, starting on pg 46.

  Regarding your MCU, if you are devoid of multimedia ports, it is probably the root cause of the problem.  Cisco have added to them, you'd only you you receive the product similar to how you added the activation keys and encryption.  If you go to the Cisco Licensing Portal, navigate to obtain other licenses > license of telepresence to return, then enter the serial number of the MCU.  It returns all the keys related to this MCU option if media ports were purchased, they should appear on the screen.  You are looking for something that says "L-5300-4PL.

• Software Version Upgradation

  Hi Experts,

  We have Cisco VC configuration with details as below:

  1. Control of VCS with version X.7.0.1
  2. MCU 4501 with software version 4.2 (1.46)
  3. Codec C40 with version TC4.2.1.265253

  The existing installation works independently and not integrated with Cisco Call Manager. Now, since we need to integrate VC with Call Setup Manager 10.5, so, we must update the versions of above material according to the link thebelow

  http://www.Cisco.com/c/en/us/TD/docs/voice_ip_comm/uc_system/unified/communications/system/versions/IPTMtrix.html#pgfId-1163447

  So, my question is on the pre-requistie to keep in mind as any DRAM or we can simply upgrade to the latest version now and later on we can upgrade integrate with Call Manager 10

  Finally, I can find the firmware TC6.3.3 and TC7.3.0 to C40. Which one should I go to?

  regds,

  Aman

  You can go directly to TC 6.x or TC7.x if you want to, with all the different security issues, probably the best going with the latest version of the software. Just need a version key valid since it is a major release of the version you currently have.

  Looking to register your telepresence to CUCM codecs? If so, suggest you read Administration of running TC7.2 on 10.5 UCM endpoints.  If you plan to save your end points of CUCM, you CUCM destined firmware.  If you plan to save your VCS or use as a standalone codec, then the software package that you have surrounded in your image, it is what you want.

  VCS will require a release key as well, since it will be a major version upgrade, the latest version is X8.5 that came out last month. MCU requires that no key release at all, so you can improve it without concern.

  If you have valid support contracts you can get the keys to release of Cisco Licensing Portal, select "Get the other licenses", then "Telepresence Software Release Key.

• telepresence license server problem

  After you install server telepresence (ova 4.2.4.23) and install license keys, under configuration > upgrade > have management got the keys next feacture: encryption of media - activation of the VM - what other permits are required for the server of telepresence? is another way to install the license to activate the function keys

  So, you have activated the multiparty licensing on driver?

  As for the question on voice only, you must look at your config, you configured following the integration of CUCM-conductor guide.

• Telepresence server pool exceeds the capacity of the license

  1, CUCM 11.0;

  2, cisco TelePresence driver XC4.2

  3, cisco TelePresence server on VM 4.3 (1.13)

  LIC-TP-SMP

  and especially the licenseis on the way.

  When I tested the video-conference with these devices that I have, I got an error:

  conferencefactory. "" "Controller: Level ="INFO"Event ="alarm triggered"Id ="50099"UUID ="fd65270e-9426-42f0-b27a-b6ad733c0e43"gravity ="error"detail ="telepresence server pool exceeds the capacity of the license: cannot create conferences as insufficient TelePresence Server license resource is available in the pool"

  I can say that the error I've met, because of the License (LIC-TP-SMP) I missed?

  You mentioned that the SMP license is "on the way"-If you have not all installed licenses? Conductor will support the old model of the "display license" or multi-stakeholder model, but whatever you use you must installed licenses or it won't work. That error seems to indicate that you have no license installed, it won't work until you solve that.

• Cisco Telepresence Server/Cisco Telepresence driver/Cisco VCS - C / Cisco TMS license

  A big problem with the fact that I'm stuck is licensing. Really, I have tried many things to find the solution for it, but could not.

  I have actually made all of these servers (mentioned in the title) in my lab in preparation for the CCNP Collaboration certification at home.

  I am not able to complete some laboratories due to license issue (I guess). Y at - it an option to get the demo license for all these servers?

  I would be really greatfull if someone can suggest me the solution and/or the licenses required to complete all the stuff for my CCNP Collab tag.

  Best regards

  Dipak Singh

  TMS and VCS - C when installed without licenses, are automatically set mode of demonstration/test with some availability of license to test with. If needing a VCS-E, you will need to do to your account manager and they should be able to get you the time limited licenses good because I think that 90 days.

  Conductor Essentials is free, which means that you can install and get full functionality without the need of all licenses, but you are limited to 1 conference bridge and no grouping is allowed.

  TelePresence Server require licenses to function, once again, reaching out to your account manager for this.

  At the end of the day, you should reach to your account manager for all of this, as they should be able to help get timed license if you need.

• Cisco Telepresence Licenses

  Hi all

  We are in the testing phase & integrated 4.0 virtual Telepresence, virtual driver XC2.3 with CUCM 8.6.2 Adhoc & Meetme Conference.

  We have THAT SX 20 recorded in CUCM endpoint. When Dial us the SX 20 its composition keep meeting & not connecting or not answered by telepresnce.

  I just noticed that there is that no license screen is installed in the server TP.

  Is it compulsory for allowing screen to make Conference calls?

  Can I register for the demo licenses file?

  Kind regards

  Francisco

  Yes, you will need licenses from the screen. Regarding the demo, I have not seen but is worth a visit with [email protected] / * /

• MSE 8510 TelePresence Server Migration - Issue of license

  I am following the process of conversion to a MCU 8510 into a server TS 8710.

  I ordered and received the migration SKU 0-dollar and have the code PAK

  Part number of top-level

  L-8000-CHLIC-PAK MSE 8000 chassis Licenses PAK PIDs

  Option part number
  L-8000-TSMO telepresence screen Option Migration, order L-8000-CHLIC-PAK

  Key question: will be recorded against this pak:

  1. The SN # MSE 8050 supervisor blade
  2. The SN # MSE chassis
  3. The SN # 8510 blade to be converted.

  There are good docs on the conversion process of loading software and the process.

  But nothing that I could find references exactly what SN # to use when registering the PAK for this process.

  The option TSMO key will apply to the MSE 8000 chassis.

  You are right, that the document is not clear where to apply, but it is also mentioned (very badly) on pg 12, in the section reference to the function keys.

• Telepresence PMP license doest work without key option TMSPE?

  Hello

  Telepresence PMP license doest work without key option TMSPE?

  The conductor, we have 250 PMP

  The STM is enabled and uses the license PMP.

  On MSDS, we have the solution for

  -Cisco TMSXE 25
  - and 50 system

  No TMSPE.

  If the use of the PMP license without the option TMSPE (license) key?

  Kind regards

  Antra

  You can install the TMSPE, Smart Scheduler and CMR functions are included for free, no license is required.  The licenses are only required if you plan provisioning VCS registered endpoints.

  TMSPE deployment guides

• TMS and ipad jabber video telepresence licenses?

  LIC-JAB-MOB-n

  You must purchase licenses for mobile devices?

  Currently, I have no license, but I'm on ipad

  Thank you

  Please see this thread

  https://supportforums.Cisco.com/message/3736583#3736583

  /Magnus

• Using License screen with local CMR 6 Solution

  Hello

  I bought the last year end Unified Workspace pro & improved part Multi advanced to exploit my Cisco Conferencing Solution, but now the license server when the virtual Cisco telepresence is managed & operated by the conductor. Conductor cannot accept that the PMP & SMP.

  Licensing Cisco team informed me that I can not update my license screen to shared Multi Party (SMP) because they we not directly purchased. Is it possible to use these licenses to screen with the current solution

  My current Versions are:

  CUCM: 11

  STM: 4.2

  Conductor: X4.1

  TMS: 15.1

  Thank you

  Ahmed

  Hi, Ahmed.

  This is the case you can not use both modes of license at the same time, it is a global driver setting.  Have you already PMP/SMP licenses on driver are you using?  If that's the case then you'd probably want to watch SL licenses advanced screen conversion / Basic PMP.   After conversion, these licenses screen would always exist on the telepresence server but PMP/SMP would prevail and they would not be used while the GST is PMP/SMP mode.

  -Jonathan