Light pink screen working area

Similar Questions

• CS5-screen work area turns black when cropping?

  I use Windows 7 and CS5.  When I try and crop a photo, the work area will become black.  Here's a clip of screen what I see.  I then cancel cropping and will sometimes return to the tool move, click the picture, black screen will return.  Suggestions or ideas why and what to do?

  

  It's a problem of display driver.

  Have you installed the 12.0.1 update for Photoshop?

  Have you recently updated your display drivers?

  Have you tried to disable OpenGL drawing in Photoshop preferences (to temporarily work around this problem)?

• Light orange vertical lines after he saw work area

  

  Problem:

  I got this funny problem. When I go to the work area, I get a strange orange lines light when I have the video playback (see attached image).

  I tried the things:
  
  -Imported the video into a sequence of AVCHD 1080i where I edited my prior full HD video. After I make the work area, some lines is not clear.
  D ' other hand, when I stick the videos in full HD on DV - PAL the sequence and make, I get same bloody light orange lines as shown above.

  Video: Screen 16:9, 720 h 576v, 25 frames, .mpg. (taken from DV camera before)

  Sequence: DV - PAL screen 16:9, 720 h 576v, 25 images

  PC: Quad Core,... enogh for this * video, published full HD on it without any problem...

  No image in your post.  I'll take a guess anyway.  NVIDIA card?

  If Yes, go to the Nvidia Control Panel and set the parameter to 'Let the 3D application decide' 3D application.

  Jeff

  EDIT: now I see the images.  My dose must resolve.

• When I turn on my computer, it gets stuck on the ultra-portable gigabyte 3 screen and custom which leave me there 2 hours still no luck the only button that works are TAB rebooting too

  Original title: stuck

  When I turn on my computer, it gets stuck on ultra-portable gigabyte 3 screen and custom wide movement which I gave 2 hours still no luck the only button that works are TAB restart too it can someone help please

  Follow these steps:

  Step 1: Start the computer in safe mode and check if the problem persists.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Start, run.

  (b) type msconfigand click OK.

  (c) the System Configuration Utility dialog box appears.

  (d) click the general tab, click Normal startup - load all services and device drivers and then click OK.

  (e) when you are prompted, click on restart to restart the computer.

• Screen works until I am asked my password to connect

  So my screen works until I am asked to connect to the place where it shows everything what image you chose for your profile.  If I boot in SafeMode the screen works properly... If I do the test and other things the screen work how it supposed to work.  But if I try to connect my regular profile it will go true dark but not black.  If I shine a bright light, I can see what I'm looking to connect and move it to my tc screen and use a keyboard wireless and mouch only problem is what use this computer for school nd cannot understand what is wrong.  I spilled a little water, but I opened and dry.  Anyone know what could be the problem for this...

  I don't know if I mentioned that works a little keyboard, but not really most of the keys are wrong or don't work.

  Hi lclutchl, welcome to the Forums of HP. If water damaged keys, you might have trouble getting the brightness comes back with the keyboard controls. I've included a few troubleshooting documents that should help you to solve the problem of brightness, if this isn't a physical problem.

  The display is Dim during or after the boot or startup

  The problems with the brightness of the screen

  If they do not contribute, or you need more help feel free to ask. If Yes, please include your computer model number and the version of Windows installed. I have included instructions on finding this information below.

  How can I find my model number of the laptop?
  Operating system Windows am I running?

• Windows 8 - start screen tiles are black after waking from sleep

  Recently installed Windows 8 Pro x 64. Whenever I have wake my computer from sleep and go to the home screen all the tiles are black, and the upper right corner where it shows my login and my avatar is missing. The rest start screen works as expected, and hovering just mouse over the tiles (or allowing the more alive to receive an update) will have show correctly.

  I was running the pre-release of windows 8 without this problem.

  My pc is completely up to date with drivers.

  Data sheet:

  I7 920

  Gigabyte ex-58-extreme (bios f12)

  2 x nvidia geforce gtx 580 in sli (310.97 driver whql)

  Samsung 840 pro 256 GB ssd (windows disk)

  2 x wd caviar black 2 TB

  Creative xfi titanium hd (newest driver 3_00_2004)

  Between the previews and update windows 8 retail I made a few changes, the only hardware change is the addition of the samsung SSD (previously on a wd raptor drive). The pilot 310.97 nvidia is also new, I was using an older version before.

  I couldn't find anyone else with this issue a web search or a search here.

  Anyone able to shed some light on this?

  Screenshot: https://skydrive.live.com/redir?resid=DB7140570445443B! 107

  I solved this problem by updating the video card drivers. I lived this question about the version of the nvidia geforce 310.97 driver, but upgrading to 313.96 has solved the problem.

• Screen works only after a hard reset.

  Hello.

  I got this dv6220la of Pavilion with a strange screen problem.

  In normal use, the screen never lights up, all lights come on, I see the drive hard drives work, but completely black screen, not even the backlight remains on.

  If I keep the power button until the laptop turns off and then turn it on, while the screen works normally.

  Whenever I turn it off normally (press the power button or use the stop dialog box) will not work after turning on the screen and whenever I have the strength it will work normally until the next power off.

  What could happen?

  ----------

  When something does not work as it is supposed to, then it works as expected.

  You have to love how useful HP support forums are always =)

• touch screen works not (windows8)

  I can't find a driver to update my touch screen. Since I put windows 8 on my all in one pc, the option of touch screen does not work. When I search for a touchscreen Windows driver, what it says that it cannot find an and to go to the site (which is hp) and watch. I've looked everywhere for a way to solve this problem. Any ideas out there for me? Help, please!

  Hello

  I had the same problem when I upgraded my TouchSmart 320-1030. I got the touch screen works in this way:

  1. Press Windows + X logo.
  2. Select Device Manager from the list.
  3. Click on the small arrow next to Interface devices to expand the list.
  4. Click on the touch screen driver (in my case, Voltron NextWindow touch screen - your driver may be different).
  5. Right click and select Disable from the list.
  6. Click Yes in the dialog box that asks you if you are sure you want to disable the touch screen driver.

  Another option:

  1. Press Windows + X logo.
  2. Select Device Manager from the list.
  3. Click on the small arrow next to display adapters to expand the list.
  4. Click the driver.
  5. Right click and select Disable from the list.
  6. Click Yes in the dialog box that asks you if you are sure you want to disable the driver.

  Another thing: I had to reinstall the NextWindow Voltron touchscreen. I went to HP drivers and downloads page, download the WINDOWS 7 driver, which was under pilot - Original.

• Equium L40 - 17 M: WLan connection but the light no longer works

  I recently transferred my laptop Equium L40 17 M. ROM Vista to Windows 7 64 bit and since that time my WiFi light has not worked - of ideas?

  Help!

  Hello

  I guess you are not able to activate the WiFi network and therefore the wifi does not work in Windows 7.

  First of all, you must make sure that the WLan card driver has been properly installed and that wireless network card has been recognized in the Device Manager.
  No yellow exclamation point must be visible in the network adapters.
  Here is a page with drivers WLan:
  http://APS2.toshiba-tro.de/WLAN/?page=downloads

  I think that your laptop support REALTEK RTL8187B WLan 802.11(B/G) card so you have to choose Realtek WLan driver.

  In addition, you should make sure that WLan is enabled;
  You must switch the WLan POSITION to allow the led WLan
  In addition, you have to use FN + F8 buttons to choose the wireless network adapter.

  If the buttons Fn would not work, then you must install the VAP (value added package) and Flash memory card Support utility. You can choose the tools available for Satellite L500...
  I did and it worked

• B590 - Main screen works only with Windows 10

  Hello.

  I have just updated to Windows 10. The first time he start it worked fine, but now the main screen does not work. During start up I see the Lenovo logo on the main screen, after that the screen goes black. The external screen works. It seems that Windows does not detect the main screen, because the Device Manager shows only 1 screen (external)! have disconnected the external screen and I made a screenshot, then some screens are shown on the Device Manager:

  Hi spidey101.

  Thanks for responding.

  It is not an arrow icon to the bottom, the icon is an icon of the Board of Directors.

  In any case I just solved it. I don't know exactly how I did it. I restarted many times, I changed the resolution of the screen for all possible modes, I tested all dual screen modes (mirror, expand, only external,...), I started in safe mode,... In the end, I unplugged everything, I removed the battery, and now it works

• CD drive does not open and the light does not work

  original title: single CD player problem

  The problem with my CD player seems to be unique I can't find an answer, or someone else with the same problem online.

  My computer is custom built, the CD player lasted me 1.5 years no problem, not until one day I realize, it does not open and the light does not work on it, I ordered a new drive and installed that one, still does not work. so, I replaced the SATA cable which connects to the motherboard, still does not.

  When I go to my computer the drive appears but when I right click > eject it says: "year error occurred while ejecting CD drive D".  It also appears in devices such as SCSI CdRom Device Manager but I am not sure if it's actually my CD player.

  I also tried troubleshooting http://support.microsoft.com/gp/cd_dvd_drive_problems and no solution.

  WTFFF ideas? I really hope that its not the motherboard

  There are two cables you need to connect to the drive, one for data and one for power.  You must connect both training at work.  If you only have the data cable is plugged and not cable power which would be a possible cause of the problem that you see.

  "Ryanb1290" wrote in the new message: * e-mail address is removed from the privacy... *

  Sorry, im just of knowledge about computer hardware.  you say that I should try a different agreement or another port to plug in?

  I tried to connect on a couple different SATA ports on the motherboard.

• Double screen of Windows 7, second screen works not properly

  I recently spent professional XP to windows 7 Home premium. I had a strange dual screen (ie. a monitor and a TV), with windows 7, I got a new drive hard (Hitachi sister hard 1 TB SATAII 7200 RPM 32 MB Cache - OEM) and installed windows 7, I have no other hardrives installed. the problem is I have a work screen (the main one) and the other is blue all the time, if I move the mouse to the edge it will disappear as if the screen works but do not reappear on the second screen. This could be the cause?

  For any question on Windows 7:

  http://social.answers.Microsoft.com/forums/en-us/category/Windows7

  Link above is Windows 7 Forum for questions on Windows 7.

  Windows 7 questions should be directed to the it.

  You are in the Vista Forums.

  See you soon.

  Mick Murphy - Microsoft partner

• Envy Touchsmart M6 Sleekbook screen works but is not lit

  Hey guys. I went to open my laptop yesterday and the power came the keyboard lights but the screen do not have. I was trying to understand if it is a physical problem or a software problem. It turns out that, when I plugged it into another monitor with a HDMI cable, the computer is always on and I can use it. Because it is a touch screen, I tried to use the screen to browse the Internet and it still worked. So, basically, the laptop still works and the screen works (because I can browse the Internet by using a different screen and the touch screen still works), but the screen itself is not lit. This sounds like a software problem or a physical problem? What ideas you guys have to fix? Thank you

  Hello dblack678,

  Welcome to the HP Forums! I hope you enjoy your stay!

  I understand that your computer screen is not lit. I'll do what I can to help you! To help you properly, I need the following information:

  1 the model number of the computer. If you need help to find this information, please see this site: find the model number of the computer

  2. the operating system. If you need help to find this information, please visit this site in order to determine the Windows operating system.

  3. have you installed new hardware on this computer, before the problem appeared?

  4. have you installed new software or drivers on this computer, before the problem appeared?

  However, since it is a new unit, I would just contact HP support. They will resolve the issue quickly, or service or replace this computer. You can use this Web site for information about how to contact HP properly, based on your region: Contact HP worldwide

  Please let me know if you have any questions or concerns. Thank you for choosing the HP Forums. Have a great day!

  Mario

• Windows 7.0 Professional, continues to crashing producing Pink Screen of Death with blue go on every start of my PC? any help please?

  I have Windows Professional 7.0 installed on my PC, which has been upgraded from Vista Premium some time ago about 18 months ago.  But recently it began to abandon the problems at startup.

  It shows a pink screen of death with blue dashes, and I must close with force by putting off circuit. On reswitching PC then start - Windows automatically selects in safe mode to "start Windows normally".  But why all the cool PC starts the screen pink death appears?  Can anyone help?

  What happened to repair Windows 7.0 Pro, (can fix you) I have the drive of the original software, I bought?  and how to on this subject, any help please? I don't want to go to the duration of backup everything and the disc Format and reinstall everything.

  If your data are not saved, at some point, you will lose this data.

  Your PC has a problem with the graphics hardware.

  This problem occurred after you installed or updated something?

  Is what brand/model PC?

• Alienware Aurora ALX lights does not work master of e/s part #.

  I tried to get the lights on my Alienware Aurora ALX job. The only lights that works are the head alien and the flange. Work, I mean that they are white. When I Command Center, it doesn't even show fan/readings of temperature or light speeds. I think that my I/o card is bad.

  I can not get something to change in Comand Center.

  I tried all the solutions on the forums and nothing seems to work.

  I reinstalled windows 3 times. Nothing.

  I reinstalled Alienware Command Center 6 times (correct version and the different)

  I tried shutting down the computer, unplug the power cord and hold the power button for 1-2 minutes thing, didn't work.

  I went to reset the map using the Green rider, did not work.

  I ran a diagnosis and everything seems fine, don't know if it's testing the Master Control I/O Board.

  I'll order an Alienware Aurora ALX Alien FX / Master Control I/O Board, because I am sure that my i/o board is bad.

  The reference is 02JXP2 and version 1.1 mine said A02

  The white mark on my map of IO said A02, but it has the same part number 02JXP2 and version 1.1.

  My question is can I use a Board with the same part number but it says A04?

  Here is a picture of the map of IO with the A02, I want to buy a economy part number 02JXP2 and at the bottom says A04 instead, but is a version 1.1.

  

  If anyone as any advice before ordering the card / advice to see if I can get the lights work on my computer?

  ThatOne_Gamer

  I don't have the cable that connects the motherboard to the MIO card.

  I'm sure that's why my ect lights do not work.

  Right... If it is not connected, it cannot work.