limit bandwidth telepresence Tandberg ex90
Hello
I have 5 ex90s.
Location1 (L1): 2
Location2 (L2): 1
Location3 (L3): 1
Location4 (L4): 1
When ex90 in place call each other, then they can use all the bandwidth as they wish.
When a place ex90 calls ex90 in another place, they can use only 1.5 M b & w.
How to implement?
Help, please!
Hello!
I wouldn't be that concerned by the individual links and tips. They will be automatically created for you when you make the subzones. You can get what you want in your simple deployment with just the configuration of the subzone. The unlimited bandwidth in a subarea and limit calls out of it to all the other subfields or areas.
1: create 4 sub-zones on your VCS.
VCS configuration > Local area > subzones.
2: for each sub-area, create a membership rule.
I guess that the TYPE can be subnet. So as a membership rule, add the subnet for the site corresponding to this subarea.
VCS configuration > Local area > subzone of the membership rules.
Subnet address and prefix length
These two fields determine the range set
of IP addresses that belong to this subarea.
(Applies only if the Type is subnet.)
Address field shows the range of
Addresses IP to assign to this subarea
based on the combination of the subnet
address and prefix length.
If you have a network at the site THAT has a network 10.1.1.0 as a C-net IP address, membership rule should be:
Subnet address: 10.1.1.0
Prefix length 24
If you have a network to the TWO site that has an address of IP 10.1.2.0 as a C-net network, membership rule should be:
Subnet address: 10.1.2.0
Prefix length 24
and so on...
3: set up the limits of subzones for your four subzones
As you can see, there is no need to set up the individual links and pipes, unless you want to do more advanced boundaries between your locations.
Robert
Tags: Cisco Support
Similar Questions
-
Certification on Tandberg Ex90 input HDMI HDMI standard.
Hi all
Recently, our client is using the mooring of the PC as a with the Tandberg Ex90 HDMI input, however, defective with the docking of Tandberg Ex90 is relatively high (about 15%). So, we discussed with the seller of mooring, and they would like to provide us with the HDMI from the Ex90 standard certification.
Anyone know the details of the certification Standard of Tandberg ex90 device?
Best regards
Ben
Hello
can you give us a detailed care of the used docking station?
Do you mean after the docking station is connected, the input HDMI 1 becomes unusable?
-
Hello, I had a question about the Tandberg EX90, I am trying to connect to a projector in the HDMI Out of the Tandberg, but it's not give signal to the projector, right now, that is - this installer is that the HDMI output:
xConfiguration video output HDMI 1 resolution: 1920_1080_60
xConfiguration video output HDMI 1 OverscanLevel: Medium
xConfiguration video output HDMI 1 EAC Mode: Off
xConfiguration video output HDMI 1 MonitorRole: second
It's not giving a signal in the projector via the HDMI Out, I checked the Option keys and it isn't a dual display Option key:
* s SystemUnit software OptionKeys DualDisplay: "false."
I need a key option for a second screen to work? It's making to work as a single monitor, which means having the same video on two screens, one of the EX90 and projector.
Kind regards.
Yes, you will need option double screen (reference number: LIC-EX90-DD).
-
Limit bandwidth consumption on a monthly
Hello
We have a customer with a Cisco CISCO1941/K9. The router has a WAN 2 connection. 1 connection has a monthly bandwidth of 20 GB/month limit and a connection high speed. The second connection is unlimited and used as a backup connection in case the main line is inaccessible.
Avoid the main connection to serve more in the cases where he used 20 GB and 20 GB/monthly make the router switch to the second connection until the new billing period begins.
Is it possible to do on a CISCO1941/K9 Cisco without premium costs / extra/software Cisco?
Thanks in advance for any response.
Sven
There is a political use of EEM on the link below. It was built to monitor the use of more than 4 G interfaces but there is no reason why it would not work for your use cases as well. Current policy alerts via syslog on BW messages and additional logic must be added to the failure of delivery on your main to backup interface.
https://supportforums.Cisco.com/document/12098671/monitor-byte-count-Ove...
-
How can I limit bandwidth used by a program on my internal network?
I am running windows 7 64 bit edition Home premium
I have a live duo network storage peripheral Western Digital mybook.
Sometimes I access multiple programs simultaneously.
I want to know how to limit speed programs access to bandwidth for one or more programs at once through my intranet.
It would help me greatly.
Kind regards
uhdunno
Hello
The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the link below.
http://social.technet.Microsoft.com/forums/en-us/w7itpronetworking/threads
Hope this information helps.
-
Hi guys,.
I use ASA Version 8.2 (1), I want to limit vpn users to use less bandwidth of my Interlink to access something on the inside of the network
example: source vpn pool
Destn: inside the network
Please let me know how to achieve this with QOS config.
Hello
Probably the best would be to match groups of tunnel.
class-map TG1-best-effort
match tunnel-group Tunnel-Group-1
match flow ip destination-address
Then this traffic in police policy-map and apply the service policy to the external interface (since you want to traffic police from your home). You can also use the pool for vpn access lists.
For more details, please see:
http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/QoS.html
-
Incompatibility of speed/duplex on Tandberg EX90
Hello
Hope you are doing well, I'm here today because I have a problem with our Tandberg based @ Zurich Switzerland.
When we connect to the web interface, we have a troubleshooting message: "speed/duplex of Missmatch.
I did the network speed auto, but it changes anything.
Could you please help me?
Often the duplex mode is auto-négocié between the two pieces of equipment; However, auto-negotiation works only if both devices are set to 'Auto '. If a device is set to 'Auto' and the other has other settings, the device of auto adapts as 100/half. The most common cause of problems of incompatibility is the scenario where a device is set to 100/full and the other is set to Auto.
- Check the configuration of the network switch where your TANDBERG end point is connected.
- Change the settings of the device so that the devices at each end of a cable have to be the same speed/duplex (1000/Full, 100/Full, 100/half, 10/Full, 10/half) parameters or are both set to Auto.
Kind regards
Acevirgil
-
For the moment this E2000 is connected to another router. The DHCP service is disabled and a LAN cable is in port 1.
I can connect the E2000 wifi a give me access to the internet.
I want the following, but I'm not able to do.
I want to give free internet access with the E2000 but want to restrict all computers so that they don't your speeds to 200 kb/s
I even if I had to use QoS and implemented by the following:
WMM support: enabled
No ACK: enabledManual 200 Kbps
High priority
port 0-65535STIL, I get speeds higher than 200 Kbps.
Hope you can help me.
He has worked with DD - wrt. I just did some tests of speed and perfect air. TNX a lot
-
How to limit the bandwidth for each different devices connected to my router
Hello
Thanks in advance!
Can you help me to limit bandwidth on perticular devices, I use NETGEAR (WNR1000v2 - N150 wireless router) and the version of the firmware of the V1.1.2.58, like almost 4 devices are connected to this router, I want to limit the speed of bandwidth to each device.
I have not found the Qos in my Netgear.
It might help if you provided in details with screenshots.
Thank you
Samira
Not possible with this model of router
-
Can I limit the bandwidth of comments for the R7000 Netgear network?
Hello dear community,
is there a way to limit bandwidth (not for games) for the network of comments?
Or you can limit the bandwidth with this router for specific mac addresses?
Is it possible to display consumption of direct download (real time) for a specific device, which is connected to the R7000?
Thanks in advance.
Same questions answered in this thread, monitor the use of data by the device X 6 R8000.
-
Bandwidth limit for MAC addresses
Is there a a way to limit bandwidth, based on the MAC address? I would like to limit certain MAC addresses or a group (invited) to about 10% of my available bandwidth.
Thank you!
It can be done by combining the IP - MAC liaison and control frequency by IP address.
-
Limit my bandwidth downloading the applications using the API to control traffic and QoS
I used QoS and Traffic Control API as TcAddFlow and TcAddFilter to control my bandwidth usage download applications.
We manipulate TC_GEN_FLOW, to send and receive FLOWSPEC parameters.
Now, I want to set the exact limit to 5 Mbps, what are the value that I need to set for TokenBucketSize and TokenRate to limit bandwidth to 5 Mbps FLOWSPEC structure?
Code snippet:
newFlow-> ReceivingFlowspec.DelayVariation = QOS_NOT_SPECIFIED;
newFlow-> ReceivingFlowspec.Latency = QOS_NOT_SPECIFIED;
newFlow-> ReceivingFlowspec.MaxSduSize = QOS_NOT_SPECIFIED;
newFlow-> ReceivingFlowspec.MinimumPolicedSize = QOS_NOT_SPECIFIED;
newFlow-> ReceivingFlowspec.PeakBandwidth = POSITIVE_INFINITY_RATE;
newFlow-> ReceivingFlowspec.ServiceType = SERVICETYPE_NETWORK_CONTROL;
newFlow-> ReceivingFlowspec.TokenBucketSize = ?;
newFlow-> ReceivingFlowspec.TokenRate =?;newFlow-> SendingFlowspec.DelayVariation = QOS_NOT_SPECIFIED;
newFlow-> SendingFlowspec.Latency = QOS_NOT_SPECIFIED;
newFlow-> SendingFlowspec.MaxSduSize = QOS_NOT_SPECIFIED;
newFlow-> SendingFlowspec.MinimumPolicedSize = QOS_NOT_SPECIFIED;
newFlow-> SendingFlowspec.PeakBandwidth = POSITIVE_INFINITY_RATE;
newFlow-> SendingFlowspec.ServiceType = SERVICETYPE_NETWORK_CONTROL;
newFlow-> SendingFlowspec.TokenBucketSize =?;
newFlow-> SendingFlowspec.TokenRate =?;Thank you & best regards
This issue is beyond the scope of this site (for consumers) and to be sure, you get the best (and fastest) reply, we have to ask either on Technet (for IT Pro) or MSDN (for developers)
If you give us a link to the new thread we can point to some resources it -
Limit the bandwidth in the tunnel VPN on Cisco ASA
Hello
I have a site VPN tunnel to create with the local desktop client. I fear that the traffic in the tunnel in impacting the Internet bandwidth for the entire office. Is it possible to limit bandwidth on the speed VPN tunnel. I have attached a configuration that shows the configuration of the ASA at the local office.
Any help would be much appreciate. I watched QoS mapping but it's hard to make sense.
Thank you very much
Kind regards
Michael.
The ASA supported QoS features are:
Police, LLQ and Traffic ShapingTo avoid the individual flows hogging the bandwidth of the network, you can limit the maximum bandwidth used by flow (with the police)
The police is a way of ensuring that no traffic exceeds the rate (in bits per second) that you configure,
so make that person not traffic or the class can return to any of the resource.
When traffic is higher than the maximum rate, the ASA removes the excess traffic. Policy defines also the largest single burst of allowed traffic.Example of font options:
class policing_map_name hostname(config-pmap) #.
Police hostname(config-pmap-c) # {exit | entry} to compliance rates [conform burst]
[action in line [drop | send]] [action exceed [drop | send]]That is to say
HostName (config) # class - police-class card
HostName(config-CMAP) # match any
HostName(config-CMAP) # QoS_policy policy-map
class police_class hostname(config-pmap) #.
HostName(config-pmap-c) # exit police 56000 10500The configuration depends on the "this" base that you want to limit the connection.
Federico.
-
Help to apply the key to unlocking EX90 after upgrade
Hello
I upgraded an EX90 to TC5 without adding the key to release first. After the upgrade, I could still access the web page, but I had to unplug the unit to go home and I contacted TAC for the key to unlocking this morning.
Now I can't the configuration web page to apply the license key.
Any ideas what the problem is?
Ricardo.
You can hava a computer connected to the same network (same switch, same vlan, same IP range).
Best have a wireshark running on this computer to see if you get something of the endpoint and tell us what is the result.
* ping to the endpoint
* ssh access (e.g. PuTTY)
* telnet
* https
* http
If it does not lead to you what it is, you can try factrory default reset:
The serial cable would need to have the touchscreen connector,... not sure the pinout.
If this does not work I would increase it to TAC
-
Hello world
One of my clients wants to answer a call, only with audio without video and video enable, if it is possible on the effects of telepresence as EX90? He doesn´t want to use "private coverage" of the camera.
I appreciate your comments.
When you place a call, you can set the call rate on ' Audio only '.
When you answer a call, I do not think there is one easy way to do it, other than the shutter of protection of personal information.
Wayne
--
Remember the frequency responses and mark your question as answered as appropriate.
Maybe you are looking for
-
I'm not getting the emails to "boxed".
All I get when I open Thunderbird is a screen but not Inbox or email downloads new or old.
-
my last mail account has been hacked and changed you can repair
my apple id changed e-mail address, it was ***@mail.ru can fix you? someone changedit < email published by host >
-
Is it possible to send for my Lenovo laptop, so they can add the Nvidia GPU? I have a T450s with Intel HD 5500, but thought that if it was possible, if they can add the GPU?
-
Wireless driver does not work on Satellite A30-PSA30E
All the ideas that is suitable for the above model driver, I downloaded about 5 drivers wireless on the site, but none seems not to work.
-
Cannot print the portable dm4 Web page
When you attempt to print from a Web page, everything that comes out is a page with "Page 1 of 1" at the top and in this down: file:///C:/Users/Susan/AppData/Local/Temp/Low/HZI6JA0J.htm with the date. I have a Pavilion dm4 and Windows 7. Thank you.