Lin Bus using a master and a slave 8476

Similar Questions

• Can I put some PFI ports on the same line for use with counters and leave the rest as static DIO? (USB-6218-USB)

  I only need a port of each line for the use of the PFI and want to use the rest for the digital I/o. Before you complete the design of the circuit and test it myself, I would like to check it out. I can't find the answer in the textbooks, either.

  Thank you

  Ben

  Hello Ben,

  If you use all the PFI lines you can use the rest as DI/O. PFI0, 1, 2, 3, 8, 9, 10, 11 are entered digital and PFI 4,5,6,7,12,13,14,15 outputs digital. Another technique you can use is to create a spot on the measurement and Automation Explorer, if it allows you to create it, then it is possible.

  Best regards

• Synchronization of 2 USRP in reception (master and slave)

  Hello

  When I run "niUSRP EX Rx finished Sync.vi " for the device USRP slave that is connected to the master via the cable MIMO. I put:
  -> MIMO frequency reference source
  The basic source of time clock-> MIMO
  I have the following error ""niUSRP Initiate.vi on the PLL reference clock does not lock in the allotted " "

  Can you help me solve this problem?
  Can you help me to synchronize two USRP in reception: a slave and the other is the master connected with cable MIMO?

  Thank you

  Hello

  When I run the master and the slave simultaneousely--> I have no error

  I use this configuration:

  IPAdressMaster = 192.168.10.2

  Frequency-> RefIn reference source
  Time base clock Source-> PpsIn

  IPAdress = 192.168.10.3

  -> MIMO frequency reference source
  The basic source of time clock-> MIMO

  Thank you for the help

• How can I add a hard disk WIN98 in my HP WINDOWS XP (as master and slave, or drive C:\ & D:\?)

  How to install a hard drive that came out a WIN98 and install it in a HP Compaq Home Edition. (Master and slave OR C:\  D:\ ?)

  Thank you please

  George

  Hello

  1. you are trying to attach an internal hard drive?

  You may need to contact the device manufacturer for more information on the physical connection and the BIOS (Basic input output) configuration when you fix the hard disk.

  Note:

  BIOS change / oxide of additional metal (CMOS) semiconductor parameters incorrectly can causeserious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Once you configure the hard drive in the BIOS, you can consult the links below for more information about how to partition and format a hard disk using the Windows XP Setup program

  http://support.Microsoft.com/kb/313348

  See also:

  How to change drive letter assignments in Windows XP

  http://support.Microsoft.com/kb/307844

• How do you change the configuration of the drive in the bios with the master and slave?

  When I bought my Dell Dimension 8300 several years ago, I had installed a DVD player and a CD + RW drive and a floppy drive installed in the system.  Very early the system crashed and the OS discs had to be reinstalled.  The Tech is frustrated and accompanied me by changing the master/slave in the bios.  My DVD player is now the master and my CD + RW is now slave.  My cd burner and DVD player play, but they do not burn or import music.  I was wondering if the fact of change that might help the problem with the stopping cd burner just in the middle of a burn error 4450 or ((0X00001162).)  Thanks for your help.

  Hello
  If you are referring to the sequence of boot Yes the bios is where you want to change it see this url http://helpdeskgeek.com/how-to/change-boot-order-xp-vista/ ... . If you are referring to master vs. slave then that is something else see this url http://www.scribd.com/doc/96827/Master-Slave-Configuration access http://support.microsoft.com/default.aspx/kb/283658 Device Manager and check for the x red or yellow?
  itunes error code points? is this correct
  I do not think that it will make a difference to change the devices around, but there's enough information here to know what to do....
  I don't think that changing the order of stertup is going to fix this problem, but again once there is info here to address this issue...
  I would however check the device mgr if there are brands so you can set from the Device Manager and there is news for this
  I think that your problems stem from itunes, if that's the case, it would be best to see if this is the case, however, if the case is you are using windows media player let us know if this post can help solve your problem, please click the mark as answer check on this page THANKS AND GOOD LUCK

• I use the master password & if I change the passwords on a site, he doesn't want to "change" also does not ask 'to remember' with new usernames/passwords. No one knows how to fix this or add the usernames and passwords on password stored in Firefox pa

  Firefox (I think version 5, maybe 4) does not ask "remember" passwords more or he asked to "change" a password when I did. He asked when I changed my Facebook password and I have to log in every time so I removed my user name and password for FB on the page of "saved the password" of Firefox. When I didn't do this before, he asks "remember" but doesn't work anymore. I use a master password.

  Make sure that you are not Firefox running in permanent private browsing mode.

  • https://support.Mozilla.com/kb/private+browsing

  To view the history settings and cookies, choose:

  • Tools > Options > privacy, choose the setting Firefox will: use the custom settings for the story of
  • Uncheck the box: [] "always use the navigation mode private.

  The Web site may use autocomplete = off to prevent Firefox to record the name and the password.

  You can remove autocomplete = off with a bookmarklet to register the name and the password of Firefox.

  • http://KB.mozillazine.org/User_name_and_password_not_remembered
  • Saved password Editor: https://addons.mozilla.org/firefox/addon/saved-password-editor/

• Using Windows 7 and 8.1 of Windows via a shared house group the WF-2540 Epson printer is off line.

  Original title: printer is offline

  using Windows 7 and 8.1 of Windows via a shared house group the WF-2540 Epson printer is off line.  This printer uses with two PCs using Windows 7 and a PC using Windows 8 with no problems.  Today it usually just printing using 1 PC with 7-1 8.  It is connected to the PC works well.  This isn't wired wireless we have wireless at the office.   Use this way for years with no problems, then suddenly this morning its all stopped.  I read so much information on it with no satisfactory response.  Epson will not know that it is not connected via radio or directly with a PC, so I'll through in circles.

  I reinstalled the PC on Windows 8 PC nothing works.  Any suggestions as to what I can try next as business has ground to stand without the printer!

  Thank you

  Hello

  Thank you for visiting Microsoft Community.

  I suggest you to post your query on our TechNet Forums social as this question right here.

  Please refer to the reference to the link below to send your request:

  https://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w7itpronetworking

  Sincerely,

  Ankit Rajput

• Adobe Acrobat XI - commenting tools: comment Cloud, polygon & lines connected cannot be selected and cannot be used

  Comment of cloud, polygon and connected lines can not be selected and cannot be used, their symbols appear lite gray. Use other tools to comment as a rectangle or circle. I already uninstalled and reinstalled the program but wihout success. Is it possible to reset the commenting tools to the State where they are provided?

  Hi Dirk Heidemann,

  Can you please make sure that "Touch Mode" is disabled in Acrobat XI. You can disable or enable the touch mode to view-> show / hide-> items-> touch Mode Toolbar. (see the screenshot below)

  

• Using Lr test, I managed to copy photos in the Catalogue and in development. Now, I want to use the photo developed/published as master and delete the original. So using the "modified" as the new source version. What is the process to do this?

  Using Lr test, I managed to copy photos in the Catalogue and in development. Now, I want to use the photo developed/published as master and delete the original. So using the "modified" as the new source version. What is the process to do this?

  This is to manually remove the master files. But are you sure you want to do this? Especially if these files are raw files? If you do, you throw a lot of precious image data. Remember that the main files are completely intact and in their original state at any time. The catalog stores all the changes that you make. But if you really want to delete your master files, you need just to delete them individually or as a group.

• I get an error (twelve updates), trying to update CS5 Master Collection.  I used the chat and was told to come here.

  I get an error (twelve updates), trying to update CS5 Master Collection.  I used the chat and was told to come here.

  update directly, http://www.adobe.com/downloads/updates/

• Hello, we have a company agreement and we are entittled to use the master collection package. Based on thi

  Hello

  We have business agreement and we are entittled to use the master collection package. Based on this, we want to upgrade Flash builder 4.7. Please let us know how can we do it and how to get the keys.

  -Med

  @Anamika018: please contact Adobe volume licensing representative technical support to access Fb 4.7 under a volume license business - they'll be able to give the right for the product.

• Lines / white space between symbols and png using grid

  Hi all

  I am having a frustrating problem:

  I am importing a bunch of images png 64 x 64 pixels. I have my set grid in place to be 32 x 32 pixels. I have snap to grid on.

  I created my scene with a bunch of these tiles 64px and everything seems perfect and lined up in the editor.

  When I debug, however, as I move around the screen, sometimes I'll see a space or a line to the intersection of the two tiles.

  Is this a common problem? Does anyone know how can I fix?

  Thank you

  Ryan

  So, I figured this out. Incase this help anyone in the future:

  I was getting caught upward in the fact that the tiles were not perfectly aligned, but it is in fact my object camera was inbetween pixels, and this caused cracks between the tiles. Before I put in the position of the camera, I just used Math.Floor and looks like it has solved this problem.

  -Ryan

• Module NI 9866 LIN bus 28V

  Hello!

  I need test a component car that runs on 28V bus LIN. It is the tension of a LIN bus service in trucks. Tension will be worn to 32V in a surge test. The specification of the 9866 VBAT voltage IS 8V to 18V, although the XNP TJA1028 LIN driver used in this module allows the 40V supply voltage. Is it possible that I can use this modul to 32V? Are there other reasons that the VBAT PIN is limited to 18V?

  Good bye

  The reason why we spec module 8-18 years is for two reasons:

  (1) the LIN standard indicates that the operating voltage of the 8 bus - 18V.

  (2) our current OR-XNET PXI/PCI LIN hardware (and the legacy USB LIN NI-CAN hardware) use a different transceiver which is only rated at 8 - 18V. If you're using something beyond this range, it will be not portable to other solutions.

  The TJA1028 data sheet there contradictory information. They are clear that 40V is their absolute maximum. In the same place, they mention that he can not work > 18V (table 7, note 5 says "to VBAT > 18 V, the transmitter from LINEN can be deleted."), but in other places, they indicate that the work is between 4.5 - 28V (Section 7.2.1: "the action RADIUS is 4.5 v to 28 V".).

  If you run between 18V and 28V, AH1003 tip Application indicates that it should work, but it is not totally guaranteed to work properly "specified functional LIN. Specified full voltage regulator.

  If you run > 28 V (surge test), you are outside the working area of the TJA1028. The TJA1028 is not guaranteed to run properly. It should be safe from damage, but it is not guaranteed to run properly. (from AH1003, "SBC will not damaged. The feature will be ok, but no parameters is guaranteed.")

  The other components in the Module 9866 that connect to VBAT should tolerate the 40V, so no problem. I'm still looking for something (power loss), but I think that even to 40V we will not exceed the admissible power dissipation.

• Is it mandatory to create/use the master page or its up to me (developer)?

  
  Hello

  I develop a form (non-interactive), where in I'm placing a lot of tables (with the approach of the subforms), and these tables is dynamic, I mean, the tables are feeding an backend ERP SAP, where of lines are dynamic (but number of columns are fixed)

  That is why I want to put FLOWED subforms, pages, bcz I have tables on the 1st page 2nd page.

  BCZ I want to mY_cmpany_logo on each and every single page, in any case only 2 pages

  Pls suggest me in this case (above said scenario), is a mandatory rule to create / use a master page

  Thank you

  XFA forms (static or dynamic) always have at least one master page, because it contains the content (s).

  Master pages are used as "wallpapers", as they are good for the items that you need to repeat on each page of the form. Think of header or footer or simly a company logo.

  Anyway, you can't place anything on a master page, if you do not want.

• Master / detail prevent insertion line detail if the master does not exist

  Hello
  
  I have a complex page that has several pairs of master / detail on it. I have what should be a simple problem to work around that I can't understand. On each table (master or detail), I have a button create header and a delete button in each row. I have a few questions, I can't seem to cross.
  
  1. how to turn off the details create button if there is no master of the line or one has not been selected by the user? (At the moment you can create detail without a valid master line rows)
  2. how to disable the removal of main line button, if there is (or not) details of current lines?
  
  I think I only got 2 having a transient attribute on the main line that uses groovy and the accessor to link views to count the detail rows. It seems to work, but if there is a better solution, cleaner I'm all ears. I can't seem to operate 1 little matter what I try.
  
  Thanks for any help you can provide.

  Hello

  You can use iterator estimatedRowCount to disable the button of

  disabled="#{!(bindings.mastervoIterator.estimatedRowCount ge 0)}"
  

  and use the currentRow determint property if the current row is selected as

  disabled="#{!(bindings.mastervoIterator.currentRow ne null)}"
  

  Thus, the combination will be as follows

  disabled="#{!(bindings.mastervoIterator.estimatedRowCount ge 0 and bindings.mastervoIterator.currentRow ne null)}"
  

  I hope this helps...

  Kind regards.