Linksys wireless-G USB wireless network monitor

Similar Questions

• Wusb54g v2 - problem with Linksys Wireless Network Monitor Software

  I have a card Linksys USB wireless (WUSB54Gv2) that is currently used with an old HP Desktop running Windows XP Service Pack 3.

  I also have a Linksys Wireless PCI Adpater (WMP54Gv4.1) that is currently used with an old Dell desktop running Windows XP.

  I have a wired and wireless home network... My broadband provider is Verizon FIOS; I use their supplied router because the coaxial cable that provides the internet connection plugs only into their wireless router, not in a modem and a router. I have an encryption key for 128-bit WEP on the side of the network wireless; It is even once managed via the Verizon FIOS router via a web browser (like most routers).

  Two other computers I own are a desk custom-made to date with a direct link to the Verizon router and a laptop from Apple. These two computers are NOT having internet connectivity problems.

  I've updated to the latest drivers for my USB adapter and the car PCI.

  ---

  Here's my problem:

  When I try to connect to the internet using the Wireless Network Monitor software provided by Linksys, computers, I can connect to the "access point", but not internet. This product only when I don't have the key WEP 128 bits in place, when security is disabled.

  If I right click on the Wireless Network Monitor icon in the taskbar and select "Use Windows XP Wireless Configuration", enter my network through windows manually information (including the WEP key), I can connect to the internet perfectly.

  However, when I restart or stop two PC, the Linksys Wireless Network Monitor reactive software itself, where it automatically attempts to connect to the internet, but fails, after which I right click on the icon of the monitor again and select «Use Windows XP...» "and then I connect to the internet.

  Is anyway to disable the Linksys continuously monitor software WITHOUT uninstalling the software or drivers? (I tried this; Windows cannot use or recognize the network adapter).

  ---

  I might just re - activate the Setup Wireless Windows XP every time I close / restart, but other users of PCs on my network (my family) are exceptionally illiterate computer/network and would not be able to learn how to do whenever they want to connect. There is very little practice.

  If there is a way to solve this situation, please help! If all goes well there are other solutions I am open to suggestions.

  I must emphasize that our Apple laptop connects fine when the WEP key is set.

  Once more, looking for quick help!

  Thank you advance!

  Remove the Linksys adapter and uninstall the Linksys software menu programs... Re - install drivers insert the CD of Linksys install in your CD-ROM drive, when the welcome is displayed click on exit, connect your USB adapter now... When the Hardware Update Wizard window appears, click on install the software automatically (recommended) and then click Next... Click Finish when the installation is complete.

  NOTE: The hardware installation screen may appear indicating that the adapter has failed the Windows Logo test. Ignore the window and click on continue to continue the installation because the adapter has been tested and it works with Windows XP. When Windows has finished installing the driver, click Finish.

  Click Start and open the control panel and double-click on network connections. Right click on wireless network connection, and then select view available wireless networks "-If you see your network wireless in the list, the highlight by clicking 'single' on it now, click on the 'Connect' button below-if your wireless network is secured, it asks you to provide the network key - provide the wireless network key and confirm again in the confirmation box and click 'Connect'." It should work...

• When you try to run Linksys Wireless Network Monitor error: cannot load ProcNICs.dll, Can t Load Res_dll

  Original title;

  Linksys wmp54g & windows vista

  When you try to run Linksys Wireless Network Monitor I get the following errors:

  Cannot load ProcNICs.dll

  Failed to load Res_dll

  Linksys wireless adapter is installed and running properly, but I can't use the application linksys to establish a new network connection.

  Any suggestions?

  Thank you.

  Hello

  I suggest you contact Linksys for assistance:

  http://home.Cisco.com/en-us/home

  Linksys Support link:

  http://homesupport.Cisco.com/en-us/support

  I hope that helps!

  If you need help on Windows, please keep us informed.

  We are here to help.

• Linksys Wireless Network Monitor Software

  I have Wireless-G Notebook Adapter v.5.0

  Need help to locate Linksys Wireless Network Monitor Software.

  I bought the Wireless-G adapter for 3 years ago and recently lost HD Crash.And software, I know that I have the disk somewhere, but cannot find it... still looking...  I tried looking for Cisco and could not find it.

  Any advice?

  Thank you

  
  

  

  I found it!, online.

  http://homesupport.Cisco.com/en-us/wireless/LBC/WPC54G

  THEN

  On the tab for:

  DOWNLOADS

  then SELECT BOTTOM LIST drop-DOWN select hardware version.

• HELP linksys wireless USB adapter: (model # WUSB54GC) "acquiring network address" not actually connect to the internet! ?? Windows xp pro

  Hello. Ive been at this for 4 days now, I can't find a solution. I'll try to remember as much as possible regarding what ive tried.

  here goes...

  long story short, due to unfortunate system errors, I have reinstalled my OS XP home to xp pro. PC works great now! problem is... now my wireless adapter wont connect to the internet.

  When I had xp home edition installed, I could just plug in the adapter, and a few seconds, it would connect to the favorite network. (with all settings on Auto) no problem.

  now that ive put in OS, it's just cycling "absorbing the network address" infinitely...

  his watch the access point, the preferred network, showing the signal strength and do not show errors in Device Manager. right-click and choosing fix do not work. It gets stuck @ renewing IP address scene. its not send or receive packets under status.

  He EXPECTED to be functional? It uses a 10-digit WEP key.

  Ive tried both the linksys wireless monitor and the windows zero configuration utilites.i since removed the lynksys software screen because it never worked anyway. WZC is that used to work on xp family.

  I used " ipconfig/all" to determine the values of the network on the host pc. I tried manually punching in those values (IP address, subnet mask, gateway and DNS settings, according to the suggestion of a networking of friends) on the adapter wireless itself; using tci/ip options. still does not connect.

  Ive tried different USB ports, all that seems to do is to change the number of the wireless connection.

  It just does not connect to the internet.

  I have the driver I need for this after contacting linksys. I also disabled windows firewall and the firewall/antivirus of 3rd party associated with the network.

  He knows questions w / windows xp professional and this particular wireless adapter? (WUSB54GC) that's the only reason why I can think of that is not connected.

  what I forget? internet hard wiring of an ethernet port is not an option because there is no ethernet card installed in the pc.

  any help is greatly appreciated in advance.

  Thank you.

  Sorry it took so long for me to return.

  It was a setting under working group which had to be adjusted from reinstalling windows. (something that has been disabled I forgot, don't remember what it was since its been like 3 weeks)

  that he got the running dhcp... That is to say. allowed 4 dependence to work progrmas, boom, problem solved.

  the adapter now works with the automatic settings, using WEP encryption. as it should, and it was.

  Thank you very much for the replies, I appreciated the help.

• Linksys wireless-g usb network adapter unable to detect the router using windows XP desktop PC

  I've changed in broadband Orange yesterday and since then my adapter is unable to find the network (it was working fine with TalkTalk until I changed).

  He managed to find a couple of other networks that are nearby but nothing else.

  I have a laptop (windows 7) who finds the router Orange immediately. I tested the adapter with the laptop and it finds the router Orange plus about 10 other nearby networks.

  I rang Orange who crossed their tests and not found any problems. I uninstalled and reinstalled the adapter on the windows XP desktop, but I get the same result.

  Can anyone help?

  Thank you

  Thanks for the reply.

  I got it finally work last night after a day of cleaning up!

  Even if the network does not have to be detected in the available wireless networks "choose" I tried the "New Connection Wizard" and entered all the details that came with the router. The adapter found the Orange router but nothing else in the region.

  For now, it works but there is a problem somewhere, because I don't see any networks, I can see on my laptop.

  See you soon.

• How can I install the driver for my monitor Linksys Wireless adapater?

  Hi, network monitor is installed when you set up the installation does not work properly so I want to install the driver for my Linksys Wireless adapater only. I've done it before, but I don't remember how.

  WUSB54GS model number

  I seems that you try this with the installation CD... Uninstall the drivers will flow and the monitor. Put the installation CD in the CD drive. and as soon as the Installer starts out out of it.

  Go to Device Manager... Try to install the drivers for the cards by selecting the location as the CD drive in my computer.

• The Epson Workforce 600 is connected via a usb cable, the other is a wireless network. I reinstalled the software of the printer (Epson) and it shows in printers and devices, but it does not list

  I have two printers installed on my laptop, only appears.  The Epson Workforce 600 is connected via a usb cable, the other is a wireless network.  I reinstalled the software of the printer (Epson) and it shows in printers and devices, but it is not the list when I go to print something.  When I select "Find a printer", it gives me a list of computer icons.

  Hello

  Check with Epson support, their documentatiion online and drivers. As it's Epson OEM
  responsible for the proper functioning of the printer and their drivers provided.

  Good luck, you need to update or reinstall the latest driver.

  Epson - Support us.
  http://www.Epson.com/cgi-bin/store/support/SupportIndex.jsp?BV_UseBVCookie=Yes

  Epson - support from Europe
  http://www.Epson.co.UK/support

  =============================================

  The main issue is probably the drivers, but these can help:

  Add or remove a printer
  http://Windows.Microsoft.com/en-us/Windows-Vista/add-or-remove-a-printer

  Solve printer problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-printer-problems

  Open the printer Troubleshooter
  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Find the manufacturer's Web site
  http://Windows.Microsoft.com/en-us/Windows-Vista/find-a-printer-manufacturers-website

  Find and install printer drivers in Windows 7
  http://Windows.Microsoft.com/en-us/Windows7/find-and-install-printer-drivers

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• How to connect a USB-wireless printer to a wireless network without PC

  Some HP printers do not have a Wizard of wireless configuration integrated into the façade to connect to a network.  These models install to a computer via a USB connection and the software then sends information wireless via the USB cable to the printer.  However, you do not always have a present computer and still need to connect these printers to a wireless network.  You can use a wireless, like an iPad device, to do this.  For the example below, I used an iPad and a printer Deskjet 3510.

  The first step is to make sure that your printer is aired at an (Ad Hoc) network.  To do this, turn on the printer and press the wireless or wireless Tower, and then in the Setup menu. Connect the iPad (or other wireless device) to the signal being broadcast by the printer wireless.

  Once the iPad is connected to the printer as long as a network connection, open the Web browser on the iPad.  Type 192.168.223.1 in the address bar and go to this site.  Printer status page should load and look like the picture below.

  

  Click the network at the top of the status page.  You can get a quick warning while being redirected to an HTTPS site.  Click Ok in the message box to continue.  When you click OK, you can get a warning about the identity of the server or the certificate.  Select the option that allows you to continue.  The wording can vary from a browser, but there should be an option to continue anyway.

  Network status page should now be loaded at this point.  Select Assistant wireless to start the installation of the wireless network and click Next.

  

  When then is selected, it must list the available wireless networks.  Select your network from the list and click Next.  When the network is selected, it should be noted.

  Enter the network password if necessary and click Next.

  

  A message should be received indicating the name and if security is enabled.  The message below which must indicate that the settings have been saved successfully.  If it indicates that the settings were saved successfully with an error, the configuration of the network is more than likely operation.  Click Ok at the bottom.

  

  After selecting OK, select status to check that the printer is connected successfully.  It may take a few minutes for light wireless to the printer to stop flashing.  Once it is a solid blue, the printer must be on the network and operation.

  

  Once this is over, then you will be able to reconnect to your wireless (wireless router) normal signal for internet access.  Now, the iPad and the printer are on the same home network.

  I hope this helps.

• Problems with wireless USB adapter. Icon missing "Wireless network connection".

  I recently got a laptop HD malfunction cause me to start my PC from 2004. I bought a Belkin N150 Wireless USB adapter to connect to the internet connectivity. During the installation, I do not get a "Wireless network connection" icon I am running Windows XP SP3. I installed the same USB adapter on a computer running Windows XP SP2 and it works fine. I plugged it in my desktop PC and it just doesn't work! Even with my router disconnected I should still be able to see other networks WiFi available in the range (I live in a community of apartment) as he worked on the other computer it elsewhere too. I double checked the drivers, reboot the cable modem, so that appropriate services were activated and still no dice. I have read forums and I'm almost at the point of paying MS for technical support services, but it's really just my last step before I shell out money for professional help. Notice to lovers? =)

  Hello

  Well, at this point, you should make an executive decision.

  If you think that someone will take just guilt because it's comfortable, it is not going to happen.

  If a new card that is known to work does not work, then you can try to re - install Windows.

  One of the differences between computer enthusiasts and regular users is the availability of the material. I have a set of wireless router, network cards, etc. that are known to be good.

  The components are used for the sole purpose of trying them temporarily on the troubled computers to rule out hardware problems.

  -------------------------------
  My posts reflect my understanding and experience. It does not necessarily reflect the opinion or the vision of Microsoft, or anyone else.

• Linksys WRT54G2 router: I can't guarantee or remove unsecured wireless network

  
  

  1. never use the default SSID "linksys". You should also do a unique SSID. If not, try your computer to connect to the router from your neighbor instead of your.

  2. Windows remembers wireless networks. You must remove the old unsecured network in the preferred networks list to get rid of him. After securing the wireless, you do not "have unsecure Linksys network. It's just that see Windows network called "linksys" and shows that all saved with this SSID wireless networks.

  So, the problem isn't the router or that a computer "picks up" a signal not secure (except even once, you really another router linksys with the default settings in the district), but the computer has a list of networks, he knows and shows that.

  Remove all linksys (SSID linksys) networks in the list of favorite networks on all of your computers. Make sure you set up a unique SSID instead and ensure that. That should do it.

  If the computers still captures a unsecure linksys network after you clear the list of preferred networks, it may be a different router. Unplug your router to power. Then again search for networks in the neighborhood. If the linksys appears again (probably with a weaker signal than before) is not your router.

• Mac OSX 10.8.4 can't see 5 GHz Linksys EA6500 wireless network

  Hello

  We have an EA6500 of Linksys router work of office. I found that Macs can't see 5 GHz network quite often but can almost always see the 2.4 Ghz network. If I restart the Mac then it can sometimes see the 5 GHz network but it's far from being reliable in trying to connect.

  Once all connected works correctly, it's just the operating system to display a list of network. If I same boot Mac in Windows 8 he can see the 5 GHz Wireless reliable every time.

  The office is in a shared office space, and there are many visible wireless in the room, about 12 now.

  I have the latest firmware of the router Linksys EA6500 (1.1.28.147876) and all software updates on Mac OSX. I fiddled with the network of automotive channels, to the setting of specific channels that seemed empty when I used a phone Android to see how busy they were.

  Has anyone seen or had any sort of resolution?

  When I get home, I have the same router and my Mac connect reliably, 100% of the time on the 5 GHz network.

  Well, I got to the low fo this. My steps, in case someone knocks something similar were:

  1. start of Fedora Core 19 Linux on my Macbook Air

  2 tries to connect to various networks near me, even if I didn't have the key

  3. notes that dmesg responded with 'country setting code' and then run dmesg and grep'd for the game of country codes

  4. after hitting one of the wireless networks, I noticed he would lie TW country code

  5. wireless network was not protected and so that a scan of the network, when her and found some web interfaces

  6. connected to the interface web and found it was a VCR Panasonic connect you

  7. once I had the wireless network manager I walked around the building with my iPhone looking force wireless looking where he was stronger.

  8. since I found that the reception office was where he was

  9. the person at the front desk denied that they had any router or wireless, it

  10. they opened a closet that had, a TV Panasonic inside recorder!

  11 identified the router right next to him.

  12A obtained in the region of router has changed for US

  Mac connect now to 5 Ghz EA6500 reliable, every time.

• wireless network and for baby monitor

  I tried to find a solution for this.  I currently have a WRT160 and a Summer Infant Baby monitor.  When I turn on the monitor during the night, I can not access my wireless network.  When I disable, wireless network is very good.  I read somewhere about that changing my wireless security wpa and has not worked.  I want to see if anyone on the forums have a fix?  There is nothing I can change the way the baby monitor broadcasts so I'll try to see what I can do with the network that just put another wireless security off.  Any thoughts?

  Yes it is.  Select 'manual' and change the channel.  Go here.

• Windows Vista Home Basic Edition, Acer laptop wireless, Linksys router and connect Lexmark X 9350 wireless network.

  I'm tired... I tried everything I can think of, as well as everything I can find online in order to connect my printer Lexmark X 9350 WiFi for my Acer laptop which is connected to my home network wireless via my linksys router. At the same time, the printer has been set up through my existing wireless network and was working properly. (FOR A SINGLE DAY!) Then I got the bright idea to installNorton Anti Virus Security. Since then, my printer stopped working through the wireless network. It works as a stand-alone Copier and fax machine, but nothing of the printer.  I contacted Lexmark via online support, but their suggestions did not work or were so confusing that it would take a computer technology to interpret the instructions to correct the problem. I learned more about the Wi - Fi networks and computer by trial and error, I should be able to re - connect my printer the eyes bandaged.  Help, please... This problem is ongoing for weeks. Thank you so much in advance.

  Just a thought, as you say it started with Norton check his firewall exceptions:

  http://TechNet.Microsoft.com/en-us/library/bb727037.aspx

  Have a read of the link above re Vista file and printer sharing.

  Permissions/Share info is there as well.

  If you use Norton, make that file and printer sharing is enabled in THE Firewall (or LAN enabled, depending on how their Exceptions are formulated in their firewall)

  See you soon.

  Mick Murphy - Microsoft partner

• on USB wireless network settings

  I was wondering if it was possible, days after setting up wireless networks on a computer, to record these settings on USB key, so that they can be used on another computer. I am running Vista family premium, I can't remmeber the keywords used for my desktop pc and I would like to set up my laptop with a USB key if possible.

  Hello deadman98,

  Thank you for using the Microsoft Answers forum.  To my knowledge there is no way to perform this task.  I suggest you connect to your wireless router and change the key.  Once you change the key, you must change the key on all systems connecting to the wireless router.

  Thank you for using answers Forum. Please let us know how it works.

  Joseph
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.