List of clients WAP200 ¿Connected?

Similar Questions

• List of Clients currently logged on 610N wireless

  Hello. I have forgotten some details in the manual, but where I am able to see that the clients are connected to the router?

  I know that my office is 192.168.1.100, but this does not seem to be recognized as a machine that is connected to the router.

  Is it supposed to show a list of customers, when I log in 192.168.1.1? Thank you for your time.

  Jim

  GoTo [status], then click on the [local area network] from the submenu. Then click on [DHCP Client Table].  That will show you what IPs and computers that are currently leased on the router.

• The VPN client VPN connection behind other PIX PIX

  I have the following problem:

  I wanted to establish the VPN connection the client VPN to PIX on GPRS / 3G, but I didn t have a bit of luck with PIX IOS version 6.2 (2).

  So I upgraded PIX to 6.3 (4) to use NAT - T and VPN client to version 4.0.5

  I have configured PIX with NAT-T(isakmp nat-traversal 20), but I still had a chance, he would not go through the 1st phase. As soon as I took nat-traversal isakmp off he started working, and we can connect to our servers.

  Now, I want to connect to the VPN client behind PIX to our customer PIX network. VPN connection implements without problem, but we can not access the servers. If I configure NAT - T on the two PIX, or only on the customer PIX or only on our PIX, no VPN connection at all.

  If I have to connect VPN client behind PIX to the customer's network and you try to PING DNS server for example, on our PIX, I have following error:

  305006: failed to create of portmap for domestic 50 CBC protocol translation: dst outside:194.x.x.x 10.10.1.x

  194.x.x.x is our customer s address IP PIX

  I understand that somewhere access list is missing, but I can not understand.

  Of course, I can configure VPN site to site, but we have few customers and take us over their servers, so it'd just connect behind PIX VPN and client connection s server, instead of the first dial-in and then establish a VPN connection.

  Can you please help me?

  Thank you in advan

  The following is extracted from ASK THE DISCUSSION FORUM of EXPERTS with Glenn Fullage of Cisco.

  I've cut and pasted here for you to read, I think that the problem mentioned below:

  Question:

  Hi Glenn,.

  Following is possible?

  I have the vpn client on my PC, my LAN is protected by a pix. I can launch the vpn client to connect to remote pix. Authenticates the vpn client and the remote pix makes my PC with the assigned ip appropriate to its pool of ip address.

  The problem that I am facing is that I can not anything across the pix remote ping from my PC which is behind my pix. Can you please guide me what I have to do to make this work, if it is possible?

  My PC has a static ip address assigned with the default gateway appropriate pointing to my s pix inside interface.

  Thank you very much for any help provided in advance.

  Response from Glenn:

  First of all, make sure that the VPN connection works correctly when the remote PC is NOT behind a PIX. If that works fine, but then breaks when put behind a PIX, it is probably that the PIX is PAT, which usually breaks IPSec. Add the following command on your PIX VPN client is behind:

  fixup protocol esp-ike

  See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/df.htm#wp1067379 for more details.

  If it still has issues, you can turn on NAT - T on the remote PIX that ends the VPN, the client and the remote PIX must encapsulate then all IPSec in UDP packets that your PIX will be able to PA correctly. Add the following command on the remote PIX:

  ISAKMP nat-traversal

  See http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pix_sw/v_63/cmdref/gl.htm#wp1027312 for more details.

  NAT - T is a standard for the encapsulation of the UDP packets inot IETF IPSec packets.

  ESP IPSec (Protocol that use your encrypted data packets) is an IP Protocol, it is located just above IP, rather than being a TCP or UDP protocol. For this reason, it has no TCP/UDP port number.

  A lot of features that make the translation of address of Port (PAT) rely on a single to PAT TCP/UDP source port number ' ing. Because all traffic is PAT would be at the same source address, must be certain uniqueness to each of its sessions, and most devices use the port number TCP/UDP source for this. Because IPSec doesn't have one, many features PAT fail to PAT it properly or at all, and the data transfer fails.

  NAT - T is enabled on both devices of the range, they will determine during the construction of the tunnel there is a PAT/NAT device between them, and if they detect that there is, they automatically encapsulate every IPSec packets in UDP packets with a port number of 4500. Because there is now a port number, PAT devices are able to PAT it correctly and the traffic goes normally.

  Hope that helps.

• VMware vSphere Client - automatic connection

  Is it possible to put in place a shortcut that will automatically log on to a server ESXi?

  The problem here is that the icon that you use to launch the vSphere client is just Launcher. If you have 3.5, 4.0 and 4.1 hosts the Launcher would make the decision on this client to connect with, according to the destination host. The usual method to find what command line options are available in the windows program is program.exe /? Is listed for the vSphere client.

• diadem environment network list network client

  It is possible the list of clients of the network through vbscript in Diadem?

  Is available in the Diadem Navigator network environment?

  Thank you

  Yustas

  Hi Yustas,

  Great, it makes sense now.  You cannot add a name DNS (\\ComputerName\...)  for a list of the 'gray' files listed under the 'My Computer' node in the tree view of the BROWSER.  All external records officially mapped by Windows, such that they have a drive letter (t or Z to appear automatically in the list of "grey" folders.)

  You can add a DNS path to a folder when you create a new field of research "yellow" under the "Areas of research" node in the NAVIGATOR tree.  My recommendation would be to add the folders that you want to load data on these remote computers as areas of research.  This will also give you the opportunity to look inside these data files without loading the and easily load channels selected, get previews of the curve, etc..

  Ask if you have any other questions,

  Brad Turpin

  Tiara Product Support Engineer
  National Instruments

• English (Singapore) on Window XP SP3 - CRM outlook client cannot connect to the CRM system

  original title: English (Singapore) on Window XP SP3

  We have an error on the CRM. CRM outlook client cannot connect to the CRM system. This question because of the language English (Singapore). We cannot locate region & language English (Singapore) on Window XP SP3.

  Hello

  ·         Do you have English (Singapore) installed on the system?

  ·         What exactly are you trying to do?

  ·         What is the exact error message, are you trying to change the system language to English (Singapore) or what?

  ·         What version of the Microsoft CRM client is installed on the system?

  To access the parameters of language and the region on the system, I suggest you to check the below link.

  Regional and Language Options overview

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/int_pr_custom_workspace_regionalsettings.mspx?mfr=true

  I suggest you to post your query in then the link mentioned below.

  https://community.dynamics.com/product/CRM/f/117.aspx

• WAG-120N and static ip - wireless and wired clients cannot connect to the internet

  Greetings,

  I use the N WAG-120 AP and switch for 3 computers laptops and 2 Office. Our Department is assigned only a what IP static of our server, as well as a pc can connect to the server and the internet. I use the first lan port of the 120N Wag as a WAN port and I attribute the static IP address, and the subnet, default gateway, and DNS addresses. Connected clients receive an ip address from the DHCP (192.168.1.10x) router, but cannot connect to the internet. How can I configure my router to allow clients to connect?

  Thank you in advance!

  The default LAN IP of the WAG subnet is 192.168.1.0/255.255.255.0 belongs to 192.168.0.0/255.255.0.0. This means that 192.168.1.0 IP addresses exist side WAN and LAN of the WAG. What makes this configuration completely cannot be routed.

  Change the address LAN IP of the WAG to an IP outside the corporate network, for example using IP addresses private 172.16/12, for example to set the address LAN IP 172.16.1.1 with 255.255.255.0 subnet mask.

  The alternative would be to use the WAG as a point of easy access only, and not as a router. However, due to the 255.255.0.0 subnet in your network company you will not be able to access the web interface except from an IP address corresponding to the LAN IP address subnet of the WAG. Of course, this does not affect the wireless or wireline customers connected to the WAG...

• Client VPN connectivity problems

  I use the cisco VPN client to connect to our network, located behind a 515E. The client is authenticated and gets an ip address but cannot ping or connect with one of the hosts. The connection is to a network of customers that is also behind a 515E. I have successfully connected using the same policy to other places and have had no problem. What confuses me, is that we have used to have a Netscreen firewall before and he had a netscreen vpn client which connected since their network with a problem. Is that something they need for their firewall so that we can get through the traffic?

  Try to turn on NAT - T on your pix, by setting up:

  ISAKMP nat-traversal 20

  and configure the client vpn accordingly:

  http://www.Cisco.com/warp/public/471/cvpn_3k_nat.html#conf_client

  I think these discussions are useful:

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=virtual%20Private%20Networks&topic=General&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1dd7dda4

  http://Forum.Cisco.com/eForum/servlet/NetProf?page=NetProf&Forum=virtual%20Private%20Networks&topic=General&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1dd7fe80

• Why I still see other appearing in my list of wireless network connection when network discovery is turned off?

  Why other users who are are my nearby?

  Can I be sure that they cannot see me when discovery of the network on my computer is off?

  Should I worry about these other users?

  I am the only computer in my home group, and my wife uses a Tablet using my wireless network key. but no one else has access to my home group.

  Discovery Network turns off the discovery of other devices that are already inside your trusted network (like your TV system game, tablets, phones and other computers).

  It does not affect the list of wireless network connection, which is actually just a list of wifi nearby broadcasting system has found.  You can not turn off without turning off your wifi.  But this isn't a security problem.

• How to force the client to connect to the specific access point?

  I have a client that connects to an Access Point to the upper floor.  The connection is "Very low" and pings are restless.  Is there a way to force the client to connect to the point of access on its own soil in the hallway.

  Access Points using 1131AG; WLC2106

  PSK + WPA2

  Thank you

  There is not a way to force the client to use a specific side access point controller of things.  According to the specifications, the client decides when and where to associate.  You can try to disable some of the rates below data or lower power tx of the AP to reduce the coverage of each access point cell.  By doing this, the client cannot see the other as favourable AP.

• How do I know if the wireless clients are connected under mode N

  Hello

  I would like to know if there is a way to know that wireless clients are connected in N mode. There is some sort of command where can show me that? I Don t have a wireless controller. My access point is AP-1141N-A-K9

  thnks!

  Unless you have a WLC, the answer is 'no '.

• Aironet 1142 standalone, no clients can connect to this topic.

  Hello

  I have a strange behavior on my standalone 1142, it's been 2 days now. No clients can connect to this topic.

  The config has been reset 5 times already, even tried with 3 different versions of IOS and still nothing.

  I put this up ever since a few years back now and it worked perfectly.

  3 days ago, I changed the PSK, it worked fine for one day and then it happened.

  I get the authentication failure of all devices that tried to connect to this topic, I even changed the configuration with no authentication, radio stations are open, the two SSID with no guarantee whatsoever, and even with no encryption I can't connect on it.

  Really strange, I was setting up Cisco AP for many years and now I have a black out... I don't know I'm missing something, I can't understand what it is...

  Any help about it please?

  Thank you

  Kyriakos

  you have a WLSM?

  If not, you should remove the

   mobility network-id 3

  and the

   mobility network-id 1

  statements that they are for communication with the WLSM

  HTH,
  Steve

• VPN Client TCP connection to router IOS

  Hello

  I try to get a VPN client to connect via TCP to a router. I currently have the router put in place (and work) in using a VPN - UDP. Unfortunately one of the sites I visit will not allow VPN traffic outside of their firewall. I have searched all over the site of Cisco and can't find any information on the IOS configuration to accept TCP - VPN connections. I would like to change the TCP port 80, so my VPN traffic looks like just standard internet browsing my client firewall. Any links/pointer would be greatly appreciated.

  Thanks in advance!

  -Joe

  Take a look at this:

  http://www.Cisco.com/en/us/docs/iOS/12_2t/12_2t8/feature/guide/ftunity.html#wp1310210

  http://www.Cisco.com/en/us/docs/iOS/12_2t/12_2t8/feature/guide/ftunity.html#wp1305478

  http://www.Cisco.com/en/us/docs/iOS/12_2t/12_2t8/feature/guide/ftunity.html#wp1315635

  Please rate if useful.

  Concerning

  Farrukh

• Cisco vpn client to connect but can not access to the internal network

  Hi all

  I have a VPN configured on cisco 5540. My vpn was working fine, but suddenly there is a question that the cisco vpn client to connect but can not access to the internal network

  Any help would be much appreciated.

  Hi Samir,

  I suggest that you go to the ASA and check the configuration to make sure that it complies with the requirements according to the reference below link:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00805734ae.shtml

  (The link above includes split tunneling, but this is just an option.

  Please paste the output of "sh cry ipsec his" here so that we can check if phase 2 is properly trained. I would say as you go to IPSEC vpn client on your PC and check increment in packets sent and received in the window 'status '.

  Let me know if this can help,

  See you soon,.

  Christian V

• Selection of the list of clients using the clause "EXISTS".

  Dear all,

  I have 3 tables, say,

  TABLE1:

   

  CUST_CODE

  (PRIMARY KEY)

  CUST_NAME

  CUST_COUNTRY_CODE

  CUST_CITY_CODE

  CUST_AREA_CODE

  A

  CUST1

  COU1

  CIT1

  A1

  B

  CUST2

  COU2

  CIT2

  A2

  C

  CUST3

  COU2

  CIT2

  A3

  D

  CUST4

  COU3

  CIT4

  A4

  E

  CUST5

  COU3

  CIT5

  A5

  TABLE2

   

  STOCK_SYS_ID

  (PRIMARY KEY)

  STOCK_CUSTOMER_CODE

  STOCK_CUSTOMER_

  COU_CODE

  STOCK_

  CUSTOMER_

  CIT_CODE

  STOCK_

  CUSTOMER_

  ARE_CODE

  STOCK_DOC_

  CREATED

  1

  A

  [Leaving empty as we have reference only to the customers and the date here...]

  10/15/2015

  2

  B

  15/09/2015

  3

  A

  16/08/2015

  4

  C

  18/08/2015

  5

  E

  22/07/2015

  6

  C

  31/01/2015

  7

  A

  15/10/2014

  TABLE 3

   

  AREA_CODE	AREA_COUNTRY_CODE	AREA_CITY_CODE
  A1

  COU1

  CIT1

  A2

  COU2

  CIT2

  A3

  COU3

  CIT2

  A4

  COU3

  CIT3

  A5

  COU4

  CIT5

  How can I find the list of clients of TABLE1, which are present in TABLE2 by 2015 and have country-city-zone, both correct mapping as specified in section TABLE3 using the clause "EXISTS".

  Is that my output will be like,

   

  CUST_CODE (ONLY CORRECT CUSTOMER CODES)

  CUST_NAME

  A

  CUST1

  B

  CUST2

  
  

  Thanks in advance,

  Séverine Suresh
  

  Hello

  So, you want to see 3 columns in table1 correspond to 3 columns in t3.  It is not enough for only 1 column equal:

  Area_Code must be equal

  country_code and must be equal

  city_code and must be equal.

  Here's a way to encode that, by using the EXISTS operator in a WHERE clause:

  SELECT cust_no, cust_name

  FROM table1 t1

  WHEN THERE IS)

  SELECT 0

  Table 3 T3

  WHERE t3.area_code = t1.cust_area_code

  AND t3.area_country_code = t1.cust_country_code

  AND t3.area_city_code = t1.cust_city_code

  )

  ;

  I hope that answers your question.

  If not, please post a small example of data (CREATE TABLE and only relevant columns, INSERT statements) for all of the tables involved and the results you want to start from these data (otherwise what you've posted already).

  Explain, using specific examples, how you get these results from these data.

  Always say what version of Oracle you are using (for example, 11.2.0.2.0).

  See the FAQ forum: Re: 2. How can I ask a question on the forums?