English (Singapore) on Window XP SP3 - CRM outlook client cannot connect to the CRM system

Similar Questions

• I had Acrobat Pro 8.3 for awhile. It is a registered product. However, as I updated to Windows 10, repeat me that it cannot connect to the internet to register or update the product

  I had Acrobat Pro 8.3 for awhile. It is a registered product. However, given that I have updated to Windows 10, he repeats that it cannot connect to the internet to register or update the product. I am connected to the Internet. What should I do?

  Thank you

  Reinstallation of my original DVD has solved the problem.

  Charlie

• Can not connect to Windows 8 on a computer that cannot connect to the internet

  Hello. I have a complex version of a common problem. I can't connect to Windows 8 on a computer that I've not used within six months. The following conditions apply.

  1. I forgot the password which was used last on this computer to turn off the line connection
  2. unable to get the computer online because the only modern it might connect to a fried.

  3. it is a Vaio Duo and has no Ethernet port.

  4. I don't care about the data, so don't mind wiping clean but I don't want to pay for the office. Computer has no hard drive, so I can't restore the BONES of the disks.

  What would you suggest here?

  Thanks for any help

  Hello

  Please provide an opportunity to help Microsoft Community.

  If you do not remember the password, you can try to reset the password online. You can use Internet Explorer to reset the password for the Microsoft Account.

  Open Internet Explorer on another computer, and then try to reset the Microsoft Account password by following the steps in the link below.

  Forgotten password and other connection problems

  As mentioned you use computer Vaio Duo which I checked comes pre-installed with Windows 8.

  If the Windows operating system comes pre-installed on the laptop, then you will need to contact the manufacturer of the system for the installation media that allows you to update or reset the settings of the computer.

  Of the manufacturer of the system provides a built in utility to repair the operating system which is known as system recovery partition, I ask you to contact you the Sony Support for more information on how to refresh/reset the settings of the computer.

  Please visit the link provided below for support from Sony:

  http://www.Sony.co.UK/support/en/product/SVD1322Y9E

  Hope that the information provided is useful. We know the results.

• Client cannot connect to the shared folders Windows 10

  I am running VMWare workstation 12.10 on Ubuntu 15.10, with a client Windows 10.  For a few days, something has changed which prevents my Windows client computer to connect to the VMware - shared folders I get error messages or notification of is that there is a problem: just a link to a folder shared!  DOEA anyone know what could be the cause?

  Hello

  Please take a look at this thread for VMware Fusion (whereas it is for the merger, the feature and thus work troubleshooting even for workstation)

  Shared folders - upgrade Windows 10 of 15.11.

  --

  Wil

• In window xp sp3, while I m trying to change the MAC ID of the loopback network adapter, its reflected in the registry but shows don't not in al/ipconfig or network connection details

  In the window xp sp3 while I m trying to change the MAC ID of the loopback network card.

  Its reflecting in the registry but does show is not in the details of network connection or ipconfig/all

  its very urgent for me so please help me out to solve this problem

  Note--> I tried to reproduce the same configuration in 5 systems XP SP3 but no luck! I so think its bug of XP SP3 because even works great for XP SP2 & 2007

  Hello

  You can follow the steps from the link below: http://social.technet.microsoft.com/Forums/en/itproxpsp/thread/0e1bf137-01e3-4dd5-9ce0-d686e6934ce4

  NOTE: Microsoft cannot guarantee that problems resulting from the use of third-party software can be resolved. Software using third party is at your own risk.

• Outlook: "cannot get mail" "cannot connect to the server.

  April 6 at 7:00 PM CST, my iPhone 5 running iOS stopped syncing with my Microsoft Outlook account 9.3.1.

  I did have problems with my iPhone sync with my Outlook email over the past 5 years so far.

  My Outlook account is to these servers-

  web mail:
  https://blu183.mail.live.com/

  for Windows Live Mail 2012:
  https://mail.Services.live.com/DeltaSync_v2.0.0/sync.aspx

  I tried to delete my Outlook account from my iPhone and re-establishment and the account Outlook 'checks' correctly - but this does not solve the problem.

  The iPhone keeps displaying a pop-up message:
  "Cannot get mail" "cannot connect to the server.

  My iPhone is syncing correctly with my Gmail accounts and iCloud.

  Also, I created my Outlook account on iPad to my daughter who is running iOS 8.1.2 and I have the same problem.

  This seems to be a situation of the Apple servers, do not sync with Microsoft servers.

  Thank you

  It seems that Outlook is to have questions, not only with iPhones but W10, see this thread:

  I lost all my contacts.

• Windows cannot connect to the printer. The name of the printer has been correctly entered, or the specified printer has lost its connection to the server.

  A Windows Server 2003 Standard Edition SP2 32-bit computer is a field, the file and print server.

  A computer on the domain is a machine of Windows 7 Ultimate 64 - bit with HP DesignJet 500 24 printer connected via USB.  The printer is running the latest firmware.  The PC is running the latest 64-bit drivers with no problems to the host machine printing.  The host also has the latest drivers 32-bit (x 86) installed by downloading by other computers on the network.  The printer is configured to share with the share name of HPDJ500.

  Now, on a machine Windows XP Pro SP3 32 bit on the field, I'm trying to connect to the shared printer.  Add a printer > click Next in the wizard of > check "a network printer or a printer attached to another computer" and then click Next > click on "Find a printer in the directory", then click Next > click Find now > HPDJ500 in the list below (the XP machine can see the shared printer on the Windows 7 computer!) and click OK.  At this point, I get an error that says: "Windows cannot connect to the printer.  The name of the printer has been correctly entered, or the specified printer has lost its connection to the server.  For more information, click Help. »

  Alternatively, if I right-click on the HPDJ500 printer listed, then click on connect, I get the same error message but I also see a separate window that says "Connecting to HPDJ500 on H2.ws.net" with the lively projector.  This window also disappears as soon as I clear the error message.

  Please note that this printer worked perfectly as a printer shared, hosted on a machine XP 32 bit on the field.  It works perfectly for the new Windows 7 64-bit machine, but we cannot connect from anywhere else on the network (including the server which translates the same exact error message).  On the server, I also preinstalled drivers thinking there was a problem with a 32-bit computer, trying to grasp the correct drivers from the host 64-bit Windows 7, but that doesn't change anything.

  How connect to this printer?

  Try using the path UNC path of the printer in the Add Printer Wizard.

  Add a printer > network printer > connection to this printer ((deuxieme point)

  Click next to browse (leave blank, the name field) or type the UNC path of the printer (i.e. \\Computername\Printername) path

• Unable to share the printer attached to the XP with windows 7, receive error message: windows cannot connect to the printer: operation failed with error 0x000004f1.

  Original title: printer HP LaserJet 4050 of PCL6 compatible with Windows 7?

  I have a desktop windows xp pro (SP3 5.1.2600) and you have a printer HP LaserJet 4050 PCL6.  The printer works fine connected to the desktop computer with a parallel port.  I'm trying to share the printer on my home network so that Win 7 (6.1.7601 SP1) laptops can use its printing features.  Please help.

  First I tried to add it with \\hostname\printername that returned this error: windows cannot connect to the printer: operation failed with error 0x000004f1.
  I downloaded and installed the Win7 drivers on the HP site on my laptop Win7, that has not changed a thing: http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareIndex.jsp?lang=en&cc=us&prodNameId=18318&prodTypeId=18972&prodSeriesId=25475&swLang=8&taskId=135&swEnvOID=4063
  Thanks in advance for any help / support!

  Hello

   

  1. the two Windows XP, Windows 7 connected in a same workgroup?

  2. can you access files shared XP of Windows 7 computer?

  3. check if the printer is shared or not?

  I suggest you follow these methods and check.

  HP LaserJet 4050 PCL6 printer is not compatible with Windows 7. Printer drivers are available for Windows XP-based computers only.

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=18972&prodSeriesId=25475&prodNameId=18322&swEnvOID=228&swLang=8&mode=2&swItem=LJ-4119-3

  It is not in the Windows 7 Compatibility Center.

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/search.aspx?l=en-us&type=hardware&s=4050%20PCL6

  I sugegst you contact HP support for Windows 7 drivers, after you instaall drivers to check with the question.

  http://WWW8.HP.com/us/en/support-drivers.html

  See also: networking computers running different versions of Windows

  http://Windows.Microsoft.com/en-us/Windows7/networking-home-computers-running-different-versions-of-Windows#section_7

  I hope this helps!

• Dell Inspiron 2650-system of operating Windows XP. I am unable to connect to the internet. Status: Network cable unplugged. Where did this cable located on the laptop?

  I have a Dell Inspiron 2650-system of operating Windows XP.  I am unable to connect to the internet.  Status: Network cable unplugged.  Where did this cable located on the laptop?

  I have a Dell Inspiron 2650-system of operating Windows XP.  I am unable to connect to the internet.  Status: Network cable unplugged.  Where did this cable located on the laptop?

  The network port is the port on the laptop (it is not that large - look around) that looks like a large phone connection.

  You have a router/network to connect to and a cable network to connect with?

  Look at the 'Network option' part of the poster:
  http://support.Dell.com/support/eDOCS/systems/ins2600/placemat1.PDF

• error message: "windows could not find a certificate to connect to the network.

  My NetGear wireless icon shows this error message "windows could not find a certificate to connect to the network.

  Hello

  Did you change your computer before this problem?

  You can follow the procedure in the article.

  Unable to connect to the network: Validation and certificate in Windows XP and Vista errors

  http://KB.NETGEAR.com/app/answers/detail/A_ID/7334/~/unable-to-connect-to-network%3A-validation-and-certificate-errors-in-Windows-XP

  Alternatively, you can contact Netgear support to improve assistance in this regard.

  Welcome to the NETGEAR support

  http://support.NETGEAR.com/

• NO wireless network connection - message "Windows could not find a certificate to connect to the network Shaida. How to fix this problem?

  I had just restored my Thinkpad T60 the default setting. Reformatted and reinstalled Windows XP, but I am unable to connect to the wireless network connection - message "Windows could not find a certificate to connect to the network Shaida.

  Shaida is my wireless modem.

  How to fix this problem?

  Before the resumption of connection Internet worked normally.

  Hello

  I suggest you to follow the steps in this link and check if it helps:

  http://support.Microsoft.com/kb/870702

  It will be useful.

• Unable to connect on the internet on another computer - "Windows could not find a certificate to connect to the network (named).

  When I try to connect to internet on my other computer I get a message saying "Windows could not find a certificate to connect to the network (name)". It's only since I've had a second computer as it does on my old computer which is

  a laptop HP Pressario with Windows XP Home Edition. Someone told me to go to authentication in wireless networks, but can highlight something here as everything is gray.

  Hello

  · What type of encryption do you use on the router?

  · You have the latest drivers for your wireless network card?

  Make sure the authentication IEEE 802. 1 x wireless card is disabled, and check if that helps.

  a. Click Start, then select run.

  b. term ncpa.cpl type dialog box and then click OK.

  c. right click on wireless network connection icon and select Properties.

  d. click the wireless network tab.

  e. click on the properties button next to remove it.

  f. click on the Authentication tab, and then clear the authentication 802. 1 x IEEE select this network check box.

  g. click OK to update the settings.

• Windows cannot connect to the Internet using HTTP, HTTPS or FTP. __This is probably caused by settings of firewall on this computer. __

  I recently installed the version of Norton, after that I was unable to use the internet, I thought it was the Norton firewall settings. After having playing with her for 30 minutes, I gave up and uninstalled Norton. I have disabled the firewall, I have reset the default settings. Here is the message I get when I run a diagnostic. A crazy thing is that I can connect to internet when I connected to this same computer as a guess.

  Please help me!

  Windows cannot connect to the Internet using HTTP, HTTPS or FTP.
  This is probably caused by the settings of firewall on this computer.

  Check the settings of firewall for the HTTP port (80), HTTPS port (443) and FTP port (21).

  Hi rhonda9937,

  1. what browser you are using to connect to the internet?

  It is not recommended to keep Windows Firewall disabled on the computer.

  This would happen if the ports are not open in the Windows Firewall.

  I suggest that you open ports in Windows Firewall and check if it works.

  How to manually open ports in Internet Connection Firewall in Windows XP

  http://support.Microsoft.com/kb/308127

  Troubleshooting settings of Windows Firewall in Windows XP Service Pack 2 for advanced users

  http://support.Microsoft.com/kb/875357

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Problem adding network printers; received this message error «Windows cannot connect to the printer or the name of the printer...» »

  Hello

  I have a Windows XP pro (Lenovo) that I recently ran the recovery and returned to certain configurations of 1.5 years. Now I can't add a network printer and get always the message error «Windows cannot connect to the printer or the name of the printer...» ». I ping the printer and all on my network can add these printers, it's just that a machine that fails to add network printers.

  I disabled the firewall, but were still unable to add the printer. Then I found some difficulties to register for a similar problem, but they were not useful... It really becomes a big headache, especially Windows restore does not work...

  I strongly suspect that 1.5 years, someone has renamed the printer.  Use Windows Explorer to navigate to the print server through My Network Places and see what it's callednow .  Otherwise, you could ask your network/system administrator.  You should know... Please vote if this has been helpful!  Please, click on Brand or propose as answer if that answered your question!

• Windows cannot connect to the printer. Access is denied.

  From: Steve

  Desperately, I try to print from my laptop Windows Vista Home Premium to a shared printer on my home wireless network.  The shared printer is connected to a XP Home machine.  This machine is wired (via a LAN cable) to the wireless router.  I can 'see' the printer that I want to use but trying to to connect to it. I get the error message "Windows cannot connect to the printer.  Access is denied. "I would be grateful for any help.

  Kind regards.

  -Steve

  From: Alan Morris [MSFT]

  Since the XP machine is HOME, I don't think that the permissions dialog box is accessible.

  Run the XP network sharing wizard again and see if it affects safety correctly on sharing.

  Is the printer you share one that has drivers provided with Windows XP?

  In the meantime we will at least get the printer works for you.

  Create a local printer on Windows Vista; Creation of a Local Port in the form \\XPMACHINE\Printsharename (this will send the files by using the redirector instead of the RPC service).  Install the Windows Vista driver for the device.

  You can print because print$ access is required for printer drivers.

  -Alan Morris

  Windows printing team

  Another response of the community of Windows Vista discussion groups