Load the screen doesn't lock

Similar Questions

• Prevents the screen turn off (locked)

  The screen turns off after a short period, as configured in the settings. But sometimes this must be disabled by software, for example the navigation software should not leave the screen get black. (BlackBerry Maps seem to handle this...)

  There are other situations where it might be a good idea to leave the screen in Active mode, perhaps the media players (watch the video) and so on.

  The page settings of the device even informs me in the operative part of security/password on the fact, that applications could extend the time until that the device will be locked with password.

  But I can't find any documentation on how the two that can be made from code.

  What permission is needed and I have to call?

  Hello

  Copy the following code prevents the lock screen:

  #include 
  ...
  Application::instance()->mainWindow()->setScreenIdleMode(ScreenIdleMode::KeepAwake);
  

• After from the screen doesn't say safe mode not optimum mode recommended 1280 104 60 h

  After said that from the safe mode screen (not optimum mode recommended 1280 104 60 h)

  Help me solve this problem.

  Thank you

  It is not a Windows problem.  It is a problem with your monitor.

  Your screen has a maximum resolution... maybe note 1280 x 960 with a 60 Hz refresh.  When you start mode without fail, the resolution of the video card is forced into a mode that will support virtually any monitor (640 x 480)?.  This is done to allow recovery in case you accidentally set your screen resolution to something that is not supported and you end up with a white screen.  When your monitor detects this less-than-optimal resolution from your computer, he takes it upon himself to post a notice on the screen informing you that you will get a better screen if you adjust the display resolution on your computer to match your monitor.  Maybe it's not possible in Mode without failure, then look at your manual of the monitor and the settings to see if there is a way to disable the warning message.

  HTH,

  JW

• I have a B1-760HD, but the brightness of the screen doesn't seem to work.

  Even with the control to its lowest setting, the screen seems to remain at the same brightness level.

  I'm probably missing something somewhere?

  Try a factory reset and then check back brightness:

  (backup all your personal data first)

  backup of the settings / & reset - Reset data

• On display at the screen doesn't work at all

  Well, that's funny... I downloaded from page pilot - HOTKEY software for my R400 with Windows Vista. I installed it, restarted the computer - nothing...
  I looked to install dir, and there in the .log file - opned it and that the joke of jokes:
  [2009-02-15 11:35:27] We Screen Display
  [2009-02-15 11:35:27] "SUCCESS: 'Not installed'-> ' 5.20.01 '.
  [2009-02-15 11:35:28] ThinkPad FullScreen Magnifier
  [2009-02-15 11:35:28] SUCCESS: 'not installed'-> '2.04'. "

  so 'Not installed' is SUCCESS... great! BRAVO! ...

  I tried to run the install again - it is written, that all drivers are installed - but the display on screen or magnifying glass does not at all.
  I tried to uninstall it, restart, then install again... and restart again... but no change - it doesn't work! I'm most update vista, where needs so problem?

  Hello wdolek,

  just a suggestion:
  Basic must install the driver interface system, after that installing hotkey features.

  Maybe it helps.

• IPhone 6 do not turn off the screen and auto lock

  I have a 16 GB iPhone gray space 6. Recently seen her phone is not automatically turn off once the pre set time settings. I tried to change settings at 30 seconds and 1 minute, and still does not.

  My friend is also similar problem on his iPhone 5s javing. The two are running latest ios 9.3.1.

  Anyone facing similar problems? All solutions?

  Have you tried a forced reboot? Hold down the home and Sleep/Wake buttons simultaneously for about 15-20 seconds , until the Apple logo appears. You won't lose anything.

• Windows 7 takes an abnormally long time to load the switch user screen

  After selecting change user in the menu closed, it takes about 30 seconds to actually load the screen of the user on the switch.  Meanwhile, the screen is black and there is no mouse cursor.  I don't remember it takes that long in the past, but I can't be sure.  It doesn't seem fair that it takes so long to load the screen of the user on the switch.

  I recently ran CCleaner and defragged my hard drive in order to fix this problem without success.

  Any help or input is appreciated.

  My system takes 20 seconds for the closing of session and prepare for a new user. A lot depends on what must be stopped as to how long it takes, and all systems will be different, so there is no default time. I also have the black screen and no cursor...
   
  CCleaner and that ilke programs rarely fix anything and are more likely to create new problems rather than fix the existing problems, this is why I say "do not use".
   
  Disk Cleanup is a safer way to get rid of some unnecessary things.
   
  /Sfc scannow will replace the corrupted system files
   
  Windows 7 repair disc... http://pcsupport.about.com/od/Windows7/HT/system-repair-disc-Windows-7.htm
   
  Windows performance Info and tools... Control Panel > performance Information and tools... Advanced tools is a useful look at surface.
   

  -Mike Hall MVP Windows: consumer http://msmvps.com/blogs/mikehall/ Mike Hall MVP - Windows Desktop Experience http://msmvps.com/blogs/mikehall/

• Locking the screen 'None '.

  Hey... I can't change the screen to zero lock. At the beginning I didn't change because I like it like that... But after I changed the profile of comments (accidentally typed it because im curious), locking the screen automatically changes to drag... Now, I can't change it because in the security settings, it has no option to put nothing, he just slide, PIN, model and password

  The Tablet is nuber Acer Iconia One 7 (the one with the lowest camera) model is B1-770

  You must remove the user invited to select none on screenlock

  https://support.Google.com/nexus/answer/6115141?hl=en

  If you are not able to remove the guest user, backup your data and do a factory reset:

  backup of the settings / & reset - Reset data

• Outlook express 6. does not full screen load. header bar 20 mm less than full screen. not scroll down bar on the screen

  My outlook express 6 program does not load the screen prperly. The header bar is less about 15-20 mm and the bottom scroll bar is not visible

  You are the very welcome. Glad it worked for you.

• Looking for shourtcut keyboard for the brightness of the screen (office 220-1128hk)

  Dear experts,

  I use a desktop model, HP all-in-1: 220-1128hk

  Although I can use the supplied software 'HP My Display' or Windows "Power Options" change my screen brightness (old one can change the screen contrast too), I always wish it could be done via the keyboard alone.

  I remember that many laptops will have a keyboard shortcut to adjust the screen brightness / contrast, for example Fn + F10 / F11.  I really wish if I can use the Fn + up / down / left / right arrows to change the screen brightness / contrast.  It would be really useful for me that I regularly need to change the setting on the day and night.  Because we have so many assigned to the function keys, it would be wonderful if the same weight is given to the screen settings.

  Are there HP (or third party) tools that can allow me to use the keyboard shortcut to change the screen brightness / contrast?

  Thank you in advance for your help!

  Best regards

  Sam

  Hello Sam_Hui. Thanks for posting on the HP Forums. I understand that you are looking for methods set the brightness of the screen. I will do my best to help you in this business! I can suggest methods that you already know, but I'll post them anyway for the sake of my methods of organization.

  First of all, I will include the product manual: http://h10032.www1.hp.com/ctg/Manual/c03401622.pdf

  Directly from the manual, I quote two possible options to adjust brightness:

  "Press the menu button on the right side of the computer.
  Opens the on-screen display menu, allowing to select the display mode (by default, movie, text, or)
  (Games), adjust the brightness and contrast and other display and sound adjustments. »

  «HP My display TouchSmart Edition allows you to adjust the screen by using the tactile feature.»
  ● You can adjust the sound, the brightness and contrast.
  ● display mode you can set the default value of the plant, or optimized for film, text, games.
  ● Status indicators let you know if the keyboard on the screen, scroll, num lock CAPS LOCK or number are defined.
  ● A settings screen allows you to set the color with the touch of a button.
  ● An options screen allows you to set display options set transparency and updates.
  HP My Display TouchSmart Edition are available from the bar of tasks, or by right clicking on the desktop, or
  on the Start Menu, tap all programs, click HP, and then click HP My Display TouchSmart Edition. Online help
  for HP My Display TouchSmart Edition is available by typing the? button in the upper right corner of the
  application screen. »

  Now, only some keyboards theoretically allow you to adjust the brightness. The standard keyboard for some of the HP Omni Touchsmarts does not do. However, HP has keyboards that have this feature and thus from other manufacturers.

  For more options, I'll give you this Microsoft Web site for your greater pleasure: adjust your screen brightness and contrast

  Please note that the site is intended for Windows 7 and Vista. However, certain information suggested applies on Windows 8 (if the computer uses Windows 8, if not, disregard this comment).

  I will propose an alternative method to close this note. However, I will not provide a lot of details. What I propose is not tolerated by HP and is a little risky If you are unsure of what you are doing 100%. This is the idea:

  You can try to apply the driver of a keyboard which contains functions of light for the keyboard you are currently using. Theoretically, if this is done correctly, you pourriez be able to configure your keyboard to adjust the brightness. There is information on the Internet about how to do it.

  I hope you find this information useful. If you have any questions or concerns, please let me know. I'm only here to help!

  Mario

• Crash of Windows Vista after the SCREEN of HOME Toshiba

  Greetings,

  My father work laptop, a Toshiba Satellite L300D, running on Windows Vista, seems to have fallen, and it is promised (because he recently ordered a new laptop) that if I fix it it gives me.

  The problem is that as soon as the laptop turns on, after the start of toshiba, but before the vista screen start loading screen, the system stops and everything is white '_' in the top left corner that flashes and disappears, leaving me with an empty black screen. I tried all below, in vain.

  • Press F8, no matter how long, when and how many times, seems to have no effect. After pressing it enough times, the laptop starts beeping for a second every time I press another key.
  • Removing the battery and pressing the power button for 60 seconds seem to have no use either.
  • The recovery disks do not work. After that they load, the screen empty boring, with the small '_' rises again.

  Please note that before any loading screen, it crashes. I tried going in the system (by pressing F2) Setup and see if there is a way of fixing it. I don't see a possible solution.

  Help, please!

  Create a Ubuntu Live CD ( http://www.ubuntu.com/desktop/get-ubuntu/download ) put it in your CD-ROM drive, and then try to start with it (go to the start menu, use the arrow keys and enter to select your CD-ROM drive), and then selecttry without any change to your computer.

  If you can boot from this summer with success, it means that it is certainly a software or a hard drive problem.
  replace the hard drive will correct these two questions (you will need to get a new operating system) or you can try to clean the drive with a live Ubuntu CD and just buy a new OS (or use ubuntu).

  to retrieve all the files you need are on the disk, read this article http://www.howtogeek.com/howto/15761/recover-data-like-a-forensics-expert-using-an-ubuntu-live-cd/

  teengeek.freehostingcloud.com

• tx2550ee starts but the screen is black after some time

  Hello

  I have pavilion tx2550ee and for a month only, it displays strange problem

  the problem:

  some time after reboot that he didn't watch anything, but windows is loaded and I hear the sound and everything is ok, but since the boot until windows is loaded, the screen is black I try to change the battery, working directly with the adapter, but nothing has changed! the screen is always black

  I leave a few time approx. 30 min it works and the display shows each thing and its ok!

  I don't know why I should leave some time at the screen to work?

  In brief

  the Tablet is booting and windows is loaded but the screen is black but after 30 minutes, it works well

  
  

  any idea?

  Thanks in advance.

  For this device, the BIOS has been certified for Windows 7 and Windows Vista only. (If you should be able to Flash the BIOS on Windows XP too, I would not recommed it).

• After the loading of barbie, equestrian club, his game is ok but the screen is black and doesn't let me do anything

  After the loading of barbie, equestrian club, his game is ok but the screen is black and doesn't let me do anything

  Hello

  1. what operating system is installed on your computer?
  2. is it works much earlier?
  3. don't you make changes before the problem?

  Check if the game is compatible with Windows 7 Compatibility Web site. The game mentioned above is not listed in the compatibility Web site, it may or may not be compatible with Windows 7.

  I suggest that you follow these steps and check if the problem persists.

  Step 1:

  Update of your display drivers and check if the problem persists.

  Step 2:

  Reduce hardware acceleration and check.
   
  a. click the Start button, Control Panel.
  b. now, select appearance and personalization. under display, select adjust screen resolution.
  c. now, select adjust the resolution.
  d. click Advanced settings.
  e. now, click the Troubleshooting tab, and select the change settings button.
  f. in the Security dialog box, click on continue.
  g. move the hardware acceleration slider to the third notch.
  h. click OK.
  i. restart Windows.

  Step 3:

  If the game worked fine in the earlier version of the operating system, I suggest you run the game in compatibility mode.

• My "restore from backup" does not end as the screen lock appears

  I got a new iphone with 64Meg and OIS 9.3.3 6 operating system. Before putting in my business phone; I backed up my data on itunes using my PC with Windows 10. As I'm trying to "restore backup" on an iphone same 6, I was unable to do, when to halfway through the download process, the screen lock appears and disconnect the iphone from itunes and the download stops. It seems to be appx 29 minutes for download; but I never got rained only 7 minutes to download completion before the screen is locked or the battery at 100% load indicator disconnect the iphone.

  I have disabled all notifications, deleted my AOL Mail, set the screen saver to "never", off of password, all without success. Help!

  Hello, Franklytex!

  Welcome to the communities of Apple Support and post your first message! Looks like you have a problem to restore your backup from iTunes. I know how important it is that your iPhone can be restored properly! Read this article which has steps for you If your iTunes backup could not be completed or you can not restore from a backup. More precisely:

  Try again after each step

  1. Make sure you have the latest version of iTunes.
  2. Connect your device to your computer with a cable USB, then Select your device in iTunes. If your device does not appear in iTunes, you must correct this problem until you can continue. Or, if you have forgotten your password or your device is off, know what to do.
  3. Turn off your computer and your iPhone, iPad or iPod touch. Then turn on again them.
  4. If you use a Mac, skip this step. If you use a Windows PC and iTunes will not respond or never ends your backup, you may need to to update, edit, disable or uninstall your security software.
  5. If you have multiple computers, try to make a backup on your other Mac or PC. Otherwise, use iCloud for save your device and restore it from your backup to iCloud.
  6. If you see an alert indicating an error has occurred, your backup is corrupt or incompatibleor there is not enough disk space, find your error message below to learn what to do next.
  7. Contact Apple technical support.

  See you soon!

• 09 pages Document is locked on the screen

  I use a template (end 2012) Mac mini. I have 10 GB of RAM and using OS 10.11.4 (El Capitan)

  Using Pages 4.3, I have developed a document which is long, 1136 pages filled with related bookmarks and many photos, resulting in a 230 MB file.

  When I opened the file, what looks like a with blue band loading zone opens first and then my precious document comes up.  Everything looks good except the so-called box loading remains on the screen and all functions in the menu bar of the application are grey, which is inactive.  so I have to force quit the application. Then, when I try to load a small file by double clicking it, only my precious document opens and the result is the same.  In short, my pages application is now inoperative.  I rebooted the computer, opened a disk check main by using the Checker utility, tried to open this document without any other apps and the problem doesn't go away.  My document seems to be blocked at the request and the opening I can't click even the document window to close.

  My fear is that I have reached a limit with pages 09 application and I do not think that Apple in their wisdom will support 09 Pages for their latest version that I can't use because the new version support not linking them, etc, etc.

  Anyone out there can help me with this problem?   If my request has been screwed is there a way I can get a new version? that is from Pages 09

  Jack

  You try to open a document v4.3 of Pages that contain unsupported features in v5 Pages, and in addition, Pages v5 is horrible when you work with exceptionally large documents bulging with other objects (for example, pictures, or tables). In addition, Pages v5 can asked you will convert the document and is quite confused about what he has found.

  Quit all applications Pages. Restart your Mac. Make at least one backup offline of your document in page 1136.

  Right click on your document v4.3 Pages ' 09 and on the shortcut menu, choose open with: Pages (4.3).