Location of RT led

Similar Questions

• HP H1W67EA #ABU: static noise in my new laptop computer

  I get a low static sound in my computer hp laptop, also one of the lights on the side of the laptop (seems to be the light of the hard drive) continues to blink on and outside.

  @Laura1989

  Thank you, it works much better. It comes to the support page for this model.

  Drivers & software for computer laptop-15 r101na (ENERGY STAR) - HP

  Also, here is the interview for this series of mobile guide. Inside, you will find other information, such as the locations of the LEDs, to better identify those who may be flashing irregularly.

  HP 15 laptop HP 15 TouchSmart PC Compaq 15 Notebook PC Compaq 15 laptop TouchSmart laptop - Guide Service and maintenance

  Notable static noise still, or is it more when the volume is in place?

  The noise seems to vary depending on what you're doing? (moving the cursor of the mouse, for example)

  Has been present static noise immediately when you first power on the laptop, or was it after using it a bit, or go online?

  There is only the driver on the site of Windows 8.1, but it may be worth put it back.

  Driver Audio Realtek High definition (HD)

  In addition, you should look through the following measures. I realize that you have sound, but many of the steps are still useful for the problems of sound quality.

  No sound from speakers (Windows 8)

  I would like to know if this helps and if not, then please post the answers wonder and I hope, it will point to a solution.

• Portege R111 - where is the 'END' button on the keyboard

  Hello

  I have a laptop Portege R111, model No. PPR11N-01KOK2.
  In the bios, I changed. The changes are applied to the key 'end '. Without changes to the ESC.

  This key 'End' I find it on the keyboard.

  Can someone tell me where the key on the keyboard?

  Thanks in advance,
  Dag

  This portable Portege is not known to me... He doesn't seem to be a European model for laptop so I did find many details on this unit... However, depends on the allocation of key keyboard keyboard language.
  On the keyboard of my computer laptop first END is located between the LED and PGDN (page down) button buttons.

  The other laptop supports another configuration of keyboard and the END key is placed between POS1 and PGUP buttons (previous page).

  Also I recommend you to check out the user manual too.
  Especially different keyboard layouts are described in operating manuals

• LINK-5 HP

  On the quick set up the sheet with the x 4500 hp wireless mouse, it shows the dongle connected to the laptop computer usb port in section 4. In section B of the same sheet show he inserted in the mouse? Why? Is it just a place to store? What does the illustration of the battery?

  Written instructions are much clearer!

  cliff6

  Hello;
  
  Let me welcome you on the HP forums!
  
  I read your post on your HP wireless mouse questions and wanted to help.

  As to the first, Yes, it's all just a place to store the WiFi dongle when the mouse isn't to ludovic.

  As for the second, which shows the location of a LED on the mouse that lights up solid at the start, and (I think) flashes with the battery is low.
  
  Good luck
  
  I'm a volunteer and I do not work for, or represent, HP.
  ========================================================================
  If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!
  
  If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.

• Add another computer to the wireless router

  Wife just HP pavilion.  I have WRT54g hssve.  How can I add his cmptr as cmptr back to the system.  already have portable added.  Cannot find procedure on CD.  What Miss me

  You must log on to your router and copy all the wireless & wireless security settings.

  Make sure that the wireless adapter on your computer is turn on.  The switch is located between the led power and your touch pad just below the word wireless. The light must be blue

  Click Start, and then connect you to.  You should see your network listed. If this is not the case, go to network and sharing Center Center and turn on network discovery.  If so, click your network name and password entry or key.

  You may have to go to set up a connection or network, and follow the instructions to manually connect to a wireless network.

• Solution on how to remove always on location service in the status bar

  Think about the last apps that you use which has led to the appearance of the purpose of the location in the status bar

  The problem is most likely due to resources are still used by these applications even if you restart your iPhone, many times

  The sign of location service can keep here.

  I tried the solution without help.

  It's a chance that I remembered the last apps I used is Runkeeper

  I went to this apps and ended.

  The problem can be solved.

  Disable background refresh App

  And also go to turn OFF the location for that Service the app & confidentiality if you think that location services is not useful for the App

• Locator is not displayed correctly

  What location opens hot link, PLACE BAR IS EMPTY. Select history to make it appear.

  Location IS NOT UNDER the 'Window' menu (some do; "show more"Mozilla Firefox").

  First tab in the window SHOWS ONLY a '+', then when additional tabs are open, you cannot navigate back to the first tab except by closing all others.

  Very rude behavior.

  I had already tried to turn off all plugins and deleting of plist file. No change.

  Your tip has led me to "help: Troubleshooting Information: Reset Firefox" which seems to have worked.

• HPPhoenixctrl: WANT to series PHOENIX - LED lighting control Solution

  I'm new to the forum and just got my new PHOENIX envy 860 - 180st, personalized with the following text:

  Windows Pro 64-bit 10

  Intel core i7-6700 4.0 GHz

  16 GB OF RAM

  512 GB SSD

  GeForce GTX 960 2GB

  No secondary drive (I store all the data on a NAS)

  Several Web pages featuring LED façade lighting, I understood that the 860 series provided a method to customize these lights.  I also believe I read that the 850 series could only turn.  However, I can not locate ANY documentation regarding the LED lights.  After hours of searching online, I only now have an interest to stop and reduce my electricity bill.  HP not me was not impressed by this "feature" negotiable.

  There is an application called HP Phoenix lighting (or LED) control which is used to control the LEDS.

  I found it in an old net while browsing through the subject.

  http://h30434.www3.HP.com/T5/desktop-operating-systems-and-recovery/missing-software-HP-envy-Phoenix-850se/m-p/5146673/highlight/true#M111153

  Check in the Control Panel, or type it in the search box on the systray next to the symbol for Windows. There could even be an icon that represents the control of lighting in the systray. My last HP 15 Omen product loan had an app called HP Omen Control, which allowed for control of groups of the backlight on the keyboard. She allowed the owner to make changes to custom groups of key color.

  If she needs relocation, then it must be done in the HP Recovery Manager. See reinstalling software and applications to the HP Recovery Manager.

  @NewEnvyOwner

  Try the following softpaq. It's called the HP utility control of Phoenix.

  http://ftp.HP.com/pub/SoftPaq/sp71501-72000/sp71672.exe

  BTW, the HP representative, that you talked to was wrong. The softpaq were found in the download of the 850 self-service portal want to Phoenix by HP Expert @Dragon-fur.

• Satellite Pro P300 LED to the bizarre behavior

  I have a portable Satellite Pro P300-1AY, bought just for more than a year. A few hours before after saving my galleries of photos on my external hard drive, a function LED (located below the touchpad) began to blink once every 2 seconds and has done since then. I can't say I've noticed this before but maybe I'm a bit on the side hypersensitive and prudent? I've never had a system failure (yet) or any error message telling me that something is wrong in particular.

  Unfortunately I don't know quite what this led to specific standards for, no power supply mains or battery either. The hard disk activity? More likely.

  As indicated, perhaps I am worrying for no reason, but it's not something I picked up before and it doesn't seem to be anything on a Google search that describes something like that.

  I appreciate any comments on this one.

  Best regards

  Gavin

  Be cool and watch what happens the next few days.
  Let us know if the same thing will happen tomorrow.

• Need driver of bright LEDS for Satellite A300

  Hey,.

  Can you tell me which driver is responsible for the A300 LED illiminated?
  I reinstalled the system, and I noticed that there is a possibility to turn on or turn off the LED through the BIOS, but it's kinda not inviting to use this way every time.
  So my question is what pilot allows me to use the first contact button on the left (sign) to light and down the diods (as in the installed oryginally system)?
  Thanks for the help,

  Kind regards
  Kuba

  Hello

  Lighting can be changed in the Toshiba HWSetup tool.
  This tool is located in the control panel.

  Start the tool and choose the lighting tab.
  It can enable and disable touchpad, the function key lighting, LED lighting.

  Check it out!

• 15-p151nr Pavilion: Pavilion 15-p151nr dead, power supply LED flashes 3 times but does not start

  With or without the adapter is connected to the computer (well known socket), the computer will not turn on.  The LED located on the left side of the computer where the socket is attached blinks 3 times (white), but does not supply power to the top.  Another post I saw said "continuous" flashing would be the power adapter, but wanted to ensure that it is in fact the problem before buying a new...  Any help would be great!

  Hi @joshuaj21,

  Welcome to the HP Forum!

  It's a great place to find answers and advice! You have the best experience in the HP forum, I would like to draw your attention to the Guide of the HP Forums: first time here? Learn how to publish and more

  I understand that the computer will not turn on. However, when you connect the AC adapter of the power port light flashes 3 times.  Please check that the power cord is not one of the recall. HP laptop AC Power Cord Safety retirement program and replacement announced August 26, 2014 .  You use a power bar?  Have you tried a different outlet? Here is a link to the HP laptops - tests and using the AC adapter which can also help.

  Please let me know the results.

  Thank you! If it helps you to find a solution, please click the button "accept as Solution"down below in this message. "If you want to say 'Thank you' to my effort to help, click on the" ""Twww.Mountainview.rsb.qc.ca Up ' give me a Kudos. : catvery-happy

• Not able to turn Mute or LED on / off on Satellite Pro P300 - 19 p

  I am more able to turn the Led lights on and off via the touch button with a picture of a light with a cross through it.

  Any ideas?

  First of all, you should check if this button has been configured correctly in the Toshiba button control.
  This utility is located in the assistance of Toshiba-> optimize

  Check if on / off lighting or Mute has been selected.

• Tecra 8100 - led flashing light

  LED on my Tecra 8100 6 flashes, then turns off then 2. I used this morning on battery until he died and then plugged in, no battery light is lit and used to power up. Anyone has any idea what it could be?

  Thank you

  Hello

  I can give you just that suggestion:
  try to remove the memory modules or just trade. Putting a module in a different location and/or a test module in both slots.

  If your machine has a serious hardware problem and should be checked by a technician...

  See you soon

• Satellite A100-590 does not fuel upward, that a single LED works

  Hello Toshiba-Crew,

  first of all I want to say sorry if you don't understand some parts of my text, but my English isn't the best more :(

  As explained in the topic I have a Satellite A100-590. I got it as a gift from my father-in-law after the A100-590 no longer works and he bought another new laptop because the customer terrible service from Toshiba.
  As much as I want to try if someone of you can help me.

  Now to point to the problem of my A100-590.
  It worked very well for my father-in-law for about a year. Then all of a sudden it no longer turns.

  The only thing that happens is the power led (the one in the middle of the five) flashes, when the power cord is connected and the power button is pressed. This light flashes 10 times and that's all that happens.
  It flashes only when the power cord is not plugged in, if only the battery is put in.

  I mention that the battery is totally empty, because the Satellite has not been used for about a year and a half now.
  The A100-590 was sent to Toshiba already, but the only thing Toshiba has done has been to send everything back one put a paper in that the motherboard needs to be changed and it would cost around 650.

  I think they don't even look at the satellite, I know that from my other computer laptop manufacturer too.
  It seems as if changing the motherboard is the best way to repair a laptop. FS said it too, but it was only one my card WIFI which was broken.

  Maybe someone of you had an idea of what might be wrong with the Satellite?
  I think this isn't a big thing, but does not fit my technical knowledge of the laptop.

  Kind regards
  Basti

  First you need to isolate the problem to the motherboard.

  Try to swap the memory modules around and try to start with a single Module, try the other location.

  If you can access the Wifi card, remove and see if it boots.

  If it still fails, then its likely to be a faulty motherboard or video card if the laptop has a.

• Satellite U400-22n - how to change the button mute for Led lighting

  Hello

  I can't turn off lighting on shortcut keys. The shortcut key to disable the LED has decided to change himself to put on mute. Does anyone know how I can pass this mute button to turn off the lights, or simply how can I turn off?

  Thanks in advance,

  Andy

  Hello

  If you are using Vista, then you should have installed VAP (value added package).
  In Toshiba Assist-> optimize you will find the configuration of buttons of Toshiba utility.
  This utility allows you to configure the buttons again.

  You must choose your button and should point to the dimmer.exe file that is located in the folder C:\Program Files\Toshiba\TBS

  Assign the dimmer.exe to the light button and complete the configuration. This should help.