locking and unlocking of the actions and workflows in the IDE

Similar Questions

• "The drive where windows is installed is locked. Unlock the drive, and then try again. »

  Have a laptop Envy M6-K010DX. Due to a problem of the internet while improving to win 8 to 8.1, the PC does not start correctly, and Windows Explorer will not load. Has decided to "Refresh" of the operating system and is gone to F11 restore utilities. When I go to the utility of refreshment and follow the prompts that I reach a message that says, 'the drive where windows is installed is locked. Unlock the drive, and then try again. "I was looking for support for the unlocking instructions and apart from some commands bootrec (which did not work - probably because I don't have a Win 8 disc) not much is available.

  The only access I have for execution of orders made by the tasks Manager command-line and F11. What is this 'locked' drive, anyway? Someone at - it any information on that?

  Hello Lara.

  IF you have updated from 8 to 8.1 and the process was interrupted during installation, this may damage the disc and therefore locked error. "Refreshing" the system would not be the answer that you need to clean install Windows 8 again. 8.1 update can break the bond of the recovery partition, especially if it has become corrupted as indicated.

  You must clean up the installation with the recovery discs, you must have created before you updated to 8.1.

  In addition, if you do not have the recovery disks, you can buy a set of HP or install a regular copy of Windows 8 and then update the drivers manually. HP has the Windows key now integrated into the bios.

  This forum is used on a voluntary basis and is not maintained by the HP Support for substitution of contact.

  Your message looks like not it was even 24 hours old before you decided to delete it from the original computer?

  I'm sorry to hear you had to do this.

  If you need to HP support, you must contact them directly to your country or region.

  Contact HP-Assist phone USA | HP® official site

  Contact HP worldwide | HP® official site

  Good luck with the new computer.

  Any brand or model you purchased now, don't forget to create the recovery disks/drive.

• locking and unlocking through the command, 'cacls' locked but not unlock

  Dear Firend I tried locking and unlocking through the command, "" D:\Murali/e/p everyone cacls: n ' "

  afterwards, while liberating, he said like that

  C:\Documents and Settings\yantra > cacls d:/Murali /e /c /p yantra:F
  ACCESS_DENIED: d:\Murali

  Please someone help me

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums:

  http://social.technet.Microsoft.com/forums/en/category/windowsxpitpro

• How to lock and unlock the computer in windows XP

  How to lock and unlock a computer with XP?

  Need to know today.

  Thank you

  Hold down the Windows key while pressing 'L '.

  "How to quickly lock your computer and use other Windows Logo shortcut keys"
    <>http://support.Microsoft.com/kb/294317 >

  HTH,
  JW

• The referenced account is currently locked and cannot be logged on to. How to unlock it?

  This is the error I get when I enter the correct password also. I have Windows VISTA and I have a set a local policy for the account lockout threshold. My friend wanted to break my password without knowing it. It is not a domain account. Mine is an independent home PC. There is a single account that is my account. I tried in safe mode (even with the command line too), but even then I get the login screen & tell me to enter the password. If I enter the password, it says "the referenced account is currently locked and cannot be saved in. There is no fingerprint reader in mine either. So how I now access my account & see my Office I couldn't since 4 days now! Suggestions, please WELCOME!

  Next time consider that to have a friend who does not really know what there mess in this connection with your computer isn't a good thing. Nor is defining an account lockout policy without knowing what you do or creating an additional administrative account so hot either.

  The faster and easier to solve this problem is to enable (disabled by default) built-in Administrator account and set a null (blank) password. Allowing this account will put an icon for it on the logon screen so that you can then you connect, make an emergency administrator account (call it something like 'CompAdmin' or 'Tech' or other), change the passwords of other accounts, etc.. When you are finished, log on the built-in Administrator and in the "CompAdmin" account and disable the administrator built-in again if you want this additional security (recommended). Leave the account "CompAdmin" rise and future emergency situations given that the account for your daily work must be a Standard account. See the end of this post for general information on configuring user accounts in Vista.

  http://home.eunet.no/~pnordahl/ntpasswd/

  Download CD (.iso) image and burn as an image, not as data. You will need a third party burning software. Then boot with the CD that you created and follow the directions.

  Once all of your changes, on the account of CompAdmin disable the administrator account integrated yet for security reasons:

  Start Orb > Search box > type: cmd
  When cmd appears in the above results, right-click and choose "Run as Administrator" [OK]. Now, you will get the command prompt. At the command prompt, type:

  NET user administrator / active: No. [Enter]

  General information of user accounts *.

  You absolutely don't want to have only one user account. As XP and all the other modern operating systems, Vista is an OS multi-user with system built-in accounts such as administrator, by default, all users and guest. These accounts should be left alone because they are part of the structure of the operating system.

  In particular, you do not want one account user with administrative privileges on Vista because the administrator account integrated (normally only used in emergencies) is disabled by default. If you use as an administrator for your daily work, and this account is corrupt, things will be difficult. It is not impossible to activate the built-in administrator to rescue things, but it will take third-party tools and work outside the operating system.

  The user account that is for your daily work must be a Standard user, with the extra administrative user (call it something like 'CompAdmin' or 'Tech' or similar) only it for elevation purposes. After you have created "CompAdmin", connect to it and change your normal user account Standard. Then log on to your regular account.

  If you want to go directly to the desktop and ignore the Welcome screen with the icons of the user accounts, you can do this:

  Start Orb > Search box > type: netplwiz [Enter]
  Click continue (or provide an administrator password) when you are prompted by UAC

  Uncheck "users must enter a user name and password to use this computer". Select a user account to connect automatically by clicking on the account you want to highlight and press OK. Enter the password for this user account (when it exists) when you are prompted. Leave blank if there is no password (null).
  ***

  Doing this requires a certain level of computer skills. You know better and if taking the machine to a competent local computer tech (not a type of BigComputerStore/GeekSquad place) is the best course of action.
  MS - MVP - Elephant Boy computers - don't panic!

• Keyboard for blackBerry Smartphones locking and unlocking in my Pocket constantly on the storm.

  Problem I have is that the keypad lock / unlock at the top on the left always gets pushed in my pocket.  When this happens, all kinds of buttons are is pressed and it screwing and calling people.  I had the Blackberry World Edition where you had to hold down two keys to unlock.  Is this something I can do with the storm?

  Password, you can protect the unit.

• How can I bitlock a device without going through the appropriate menus and related software to lock and unlock a device?

  Original title: ILO-locked usb device

  I have a 64 GB... new USB key... and put music on it. After a while, I decided to use it for another use, but could not remove the files because the device is write-protected. I never write protect anything.

  I had an individual look of microsoft cert to the USB and he said it was not locked.

  I did some research on bit locker and Win 7 Pro and discovered that I can't find the Group Policy Editor where all bit locker said tech data is located.

  So, how can I lock bit, a device without going through the appropriate menus and associated software application necessary to lock and unlock a device?

  Hello

  When you turn off BitLocker, you can either disable BitLocker temporarily or to decrypt the volume. Disable BitLocker allows TPM and other minor changes module changes the system. Decrypt the volume means that the volume will be entirely decrypted, and that all the keys are ignored. You must decrypt a computer before the operating system upgrade. Once a volume is decrypted, you must generate new keys through the encryption process again once, if you want to enable BitLocker.

  Before you start

  > You must be logged in as an administrator.

  > The volume must be encrypted.

  To turn off BitLocker Drive encryption

  (a) click Start, click Control Panel, click Security, and then click BitLocker Drive Encryption.

  (b) from the BitLocker Drive Encryption page, find the volume on which you want BitLocker Drive Encryption goes off, and click turn off BitLocker Drive Encryption.

  (c) what level of decryption do you want the dialog box, click disable BitLocker Drive Encryption or decrypt the volume as required.

  (d) by performing this procedure, you have disabled BitLocker or decrypted the operating system volume.

  For more information, see the articles:

  Turning off BitLocker Drive encryption

  How to use the unlock options in BitLocker Drive encryption?

  Protect your files using BitLocker Drive encryption

  Hope the helps of information.

• Lock and unlock the buttons in related specifications

  Hello

  By default for us when we add any requirement under the specification of the material, trade related specifications Spec tab by default is to show the lock button we want it to be unlock position and when I went through the config doc I saw mobile PHONES. GetCustomRevision.FormulationSpecAlternates.Default.Enabled set to true in the custom settings, and then on the release button will be there by default.

  Is - it can be done by setting up or do we need to make other changes in all other files.

  Please suggest.

  Thank you

  Rohini.

  
  

  You are right, if you set which the true will set the lock to be "unlocked".  The location you mentioned is for grid alternate specifications of formulation.

  The specification of trade has its own configs as well:

  "GSM. GetCustomRevision.TradeSpecMaterial.Default.Enabled"will control the grid of Spec material on a Spec of trade

  "GSM. GetCustomRevision.TradeSpecNextLowerLevel.Default.Enabled"will control the next lower spec trade level grid on trade specifications.

  A complete list of locations are in the Configuration page of the guide to-22.

• When I open a photo in CS5 the layer is already locked and will not unlock. Cannot crop etc. This just started happening. Ideas?

  When I opened a new photo layers are automatically locked and not will not unlock. It only started happening. Any ideas?

  Some formats like jpg does not support layers, that's why it opens as a locked background layer.

  You can unlock the layer by dragging the padlock in the trash. This will convert the background layer to a regular layer.

  If this is still insufficient, capture your screen with the open layers panel and everything collapsed expanded layers. Then post here so we can see what is happening.

• Why can't respond to the messages of my lock and the home screen?

  I have the iPhone 6 + and I recently updated for IOS 10 and just discovered that I can't respond to the messages of my lock screen, or when they appear at the top of my home screen; I have to go in the app to answer. The only options I have when I slide right to lock screen is 'view' (which has just expanded the text) or 'clear', I found this quite irritating and regret the update of my phone. In the home screen when I pull down on the text, it just amplifies it and that's all, the keyboard is not pop up. Help, please...

  Hi there Choulian,

  Welcome to Apple Support communities.  I'm glad you brought your question to be able to respond to messages directly from the lock screen, it is a feature I use all the time and I know it's convenient not having fully unlock and go to the app to respond quickly to a text.

  Let's check some settings to make sure that we have everything set up correctly for you to be able to respond to messages from the lock screen.

  The application of settings:

  1. Touch ID & password (enter your access code)
  2. Scroll down to ALLOW ACCESS when it is LOCKED
  3. Don't forget that respond with Message is enabled and set to green

  Take care!

• while sleeping, the computer is locked and cannot be opened by the administrator

  Help. I have an old computer second, forwarded by a friend that I have more contact with. This computer is used daily by another friend who doesn't have a computer.

  every night the computer go to sleep and the next day when he woke up that my bud Gets a message that it is locked and only the admin can open it.

  I changed it to the administrator, but when the screen opens and he tries to enter the password, the screen seems FROZEN and don't let him enter his password.

  . the only way to work around this problem seems to be to restart. as the machine is old, reboot may take 10 minutes or more. What can be done to avoid this mess?

  Oddly it only happened in the last 2 weeks... for almost a year that wasn't a problem...

  concise simple tips are appreciated.

  Steve

  Hello

  See if that helps you.

  The second part is on XP and standby / sleep of password.

  http://www.mydigitallife.info/disable-Windows-XP-and-Vista-from-asking-for-password-to-unlock-on-wake-up-resume-from-sleepstandby/

  And there is an option of password screensaver in XP, too;

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/display_assign_screensaver_password.mspx?mfr=true

  Doing this is reverse:

  http://www.computerhope.com/issues/ch000790.htm

  See you soon.

• Why a popup window that says my computor is locked and cannot be unlocked by my password

  When I go to my computor, a window pops up saying that my computor is locked and can only be unlocked by using my password that I do not have.

  You probably got in place so that it automatically at startup and insert your password.  The likely reason you have this lock w / password problem is that you have set up a screen saver and checked the box "on RESUME, Password Protect."  To verify, right-click on an empty space on the desktop-> properties-> Screensaver (tab) and change the password protection checkbox.

  Even better, once you are on your computer, go to the 'Users' Panel and change your password to something that you will remember.

  HTH,
  JW

• When you run the virus scan, the majority of the files and folders showing locked and impossible to scan in Vista

  When I run my anti-virus, it tells me that almost all my folders and files, or are locked and is not be scanned... How to unlock folders or files that I have windows vista 64-bit

  * original title - how to unlock files and folders on my windows vista 64 bit computer when I run my anti-virus scan all folders and files are locked *.

  Hello

  ·         What program Antivirus do you use?

  This problem may also come from Virus/Malware infection on the system.

  I suggest you to run the Microsoft Safety Scanner and check if that helps resolve the issue.

  The Microsoft Security Scanner is a downloadable security tool for free which allows analysis at the application and helps remove viruses, spyware and other malware. It works with your current antivirus software.

  Note:

  The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.

• locking the computer: if not using computer for a while, it locks and requires the initial password to get in

  So do not use computer for a while, it locks and requires the initial password to get back in. When it becomes available, we've been thrown off internet, or another program we are.

  I don't know why Mr. Murphy suggested a system restore. Maybe he interpreted your post differently I did. You have your screen standby/power options defined on too short a time. You can also disable the requirement for a password during the recovery.

  Right-click on an empty area of the desktop and click on personalize. To customize the applet opens. Click the screen saver. Change the timeout to something reasonable like 10 or 20 minutes. You will see where you can clear the check box next to the "password required on curriculum vitae... ».

  Now do the same in the (Control Panel) Power Options applet. This link contains pictures showing you how to disable this option:

  http://www.mydigitallife.info/2008/06/29/disable-Windows-XP-and-Vista-from-asking-for-password-to-unlock-on-wake-up-resume-from-sleepstandby/

  MS - MVP - Elephant Boy computers - don't panic!

• Wireless use USB ports locks and prevents the Windows shut down

  Hi all. Faced with this one.

  Computer is the laptop, HP Pavilion DM4 - 1150ca. 4 GB of Ram, 150 GB HD

  OS Win 7 Home Premium 64-bit, SP1 and latest updates installed

  Problem: I have 3 ways to connect to the internet: 1 Dongle USB (Device Manager calls "Remote NDIS based internet device for sharing". No problem connecting to the network and to the internet with this device. 2. built in WiFi adapter, "Intel Centrino Wireless - N 1000 and 3. External antenna for high power USB and USB «Realtek RTL8187» adapter Medium 1 and 2, I can normally connect to the network, get decent speed but he declines quickly and then to a random period, usually within a few minutes, I lose my internet connection, and finally my network shows disconnect icon. At this stage all 3 of my USB ports are locked up, removal of the WiFi device does nothing, don't disconnect sound and no USB device is recognized if I try their connection. In addition, Windows will not stop. I get a "shutting down" screen but it stays that way until the expiration time and finally restarts, screen asking if I want to start normally or in safe mode.

  Action taken:

  Several online sites checked and tried solutions including:

  RTL8187 uninstalled and reinstalled several times

  Uninstalled and reinstalled HP wireless several times

  Deleted (Device Manager, see all) entries while grayed, unused network

  So far, no joy, no change. Anyone have any new ideas? Thanks for any help

  Hi Raven,

  Do you have third-party security programs installed on the computer?

  Basically, if the internet works in safe mode and not works in normal mode, not applications or third-party security programs can be in conflict with the drivers from the internet.

  As a solution, I suggest to uninstall the anti-virus program and check if it works in normal mode.

  Warning: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Answer with the results so that we can help you even the question.