loop label

Similar Questions

• Nestled in the issue of the loop

  Hello

  I have something like this

  begin
    for r in (select * from table_a where data_start <= sysdate) loop
      <something>
      for r_prod in (select * from table_b) loop
        for p in (
          select * from table_c where ....... and rownum = 1
        ) loop
  -- <do something>
          -- and then I want to exit from the current loop (p), and r_prod also, and jumping to the next iteration of "r" cursor.
        end loop;
      end loop
    end loop;
  end;
  /
  
  
  

  Is it possible to get out of the third loop, the second also and go to the next iteration of the hand for... loop (with continue statement)?

  Thank you!

  Just the outer loop label and use...

   

  CONTINUE outer_loop;

• How to quit the nested loop

  I have a nested loop
  
  loop1 start
  ...
  loop2 start
  ...
  end loop2
  ...
  end loop1
  
  I want to know how can I come out the two loops of the inner loop.

  Hello
  Out of the inner loop in the use of nested loops labels

  SQL> BEGIN
    2          <>
    3            FOR i IN 1..2 LOOP
    4                 <>
    5                 FOR j IN 1..4 LOOP
    6                      DBMS_OUTPUT.PUT_LINE('I am in Inner Loop');
    7                 END LOOP inner;
    8       DBMS_OUTPUT.PUT_LINE('I am in outer Loop');
    9            END LOOP outer;
   10   END;
   11   /
  I am in Inner Loop
  I am in Inner Loop
  I am in Inner Loop
  I am in Inner Loop
  I am in outer Loop
  I am in Inner Loop
  I am in Inner Loop
  I am in Inner Loop
  I am in Inner Loop
  I am in outer Loop
  
  PL/SQL procedure successfully completed.
  
  SQL> BEGIN
    2          <>
    3            FOR i IN 1..2 LOOP
    4                 <>
    5                 FOR j IN 1..4 LOOP
    6                      DBMS_OUTPUT.PUT_LINE('I am in Inner Loop');
    7       exit inner;
    8                 END LOOP inner;
    9       DBMS_OUTPUT.PUT_LINE('I am in outer Loop');
   10            END LOOP outer;
   11   END;
   12   /
  I am in Inner Loop
  I am in outer Loop
  I am in Inner Loop
  I am in outer Loop
  
  PL/SQL procedure successfully completed.
  
  SQL>
  SQL> BEGIN
    2          <>
    3            FOR i IN 1..2 LOOP
    4                 <>
    5                 FOR j IN 1..4 LOOP
    6                      DBMS_OUTPUT.PUT_LINE('I am in Inner Loop');
    7       exit outer;
    8                 END LOOP inner;
    9       DBMS_OUTPUT.PUT_LINE('I am in outer Loop');
   10            END LOOP outer;
   11   END;
   12   /
  I am in Inner Loop
  
  PL/SQL procedure successfully completed.
  

  Twinkle

• Twice in loop and stop at a record label?

  Hello community,

  
  My question:

  How can I loop my entire animation twice * and after that judgment to label a frame?

  It's the same question about it , but this time to animate the CC.

  Example:
  A banner has 100 images. It must be a loop twice from 0 to 100, then plays entre0 and stop at frame 80.

  
  Thank you

  Michael

  * Copy the following code loops all the animation twice:

  {if(!this.alreadyExecuted)}

  this.alreadyExecuted = true;

  this.loopNum = 1;

  } else {}

  this.loopNum ++;

  {if(this.loopNum==2)}

  This.Stop ();

  }

  }

  You can place this code in the frame of 80, and he would do what you ask for. Make sure that in the publication settings, you have the chronology of verified loop box.

• The entire animation twice in loop and stop at a record label?

  Hello community,

  I can't find out how my banneranimation stop a label after completing two loops.

  I tried different approaches I found in Google searches, but none of them seems to apply to the way my banner is constructed

  Can anyone help?

  You can download the entire project here

  Hello

  You have 2 examples with your own project here: read and stop a movie.

  I use a meter to check your movie using the dashboard API: sym.setVariable () and sym.getVariable ().

  • I have create a counter: sym.setVariable("loop",1);
  • I increment the counter: sym.setVariable ("loop", sym.getVariable ("loop") + 1);

• How to make a label refresh when it is used as a counter in a loop?

  Hello

  I would like to have a label or any other control refreshes and displays some kind of progress in a loop like this:

  for(var z:int=0; z<Something.length; z++) {
   // Do some processing ...
   
   // Display the progress ...
   lblProgress.text = "Progress: " + z.toString() + " / " + Something.length.toString();
   lblProgress.validateNow();
  }
  
  

  The problem I have is that the update happened once at the end of the processing loop.  How could force the system to display each loop?

  Thank you.

  See Event.ENTER_FRAME

• Loop of random image labels

  Hello.  I recently received a code from the blog of David Stiller I like a lot.  It is about how to get a series of labels of image to read in random order without ever repeating.  It's great, and I understand most of the code.

  However, when all the labels image have been "played", I don't just go and rest/stop on the last image.  I want that he begin the process again.  Is there a way to do this?  Here is the code that I currently have:

  function shuffle(arr:Array):Void {
  var len:Number = arr.length - 1;
  for (var i:Number = len; i >= 0; i--) {
    var p:Number = Math.floor(Math.random() * (i + 1));
    var t:Object = arr[i];
    arr[i] = arr[p];
    arr[p] = t;
  }
}

var labels:Array = ["a", "b", "c", "d", "e"];
shuffle(labels);

var currentLabel:Number = 0;
function gotoNextLabel():Void {
  if (currentLabel < labels.length) {
    gotoAndPlay(labels[currentLabel]);
    currentLabel++;
  } else {
    stop();
  }
}
gotoNextLabel();

  Here's the blog entry, I got it from: http://www.quip.net/blog/2007/flash/how-to-jump-randomly-to-frame-labels-without-repeatsht tp: / /

  I guess I have to replace 'stop' towards the end with something else, but what?  Repeat?

  use:

  function shuffle(arr:Array):Void {
  var len:Number = arr.length - 1;
  for (var i:Number = len; i >= 0; i--) {
    var p:Number = Math.floor(Math.random() * (i + 1));
    var t:Object = arr[i];
    arr[i] = arr[p];
    arr[p] = t;
  }
}

  var labels:Array = ["a", "b", "c", "d", "e"];
  shuffle(labels);

  var currentLabel:Number = 0;
function gotoNextLabel():Void {
  if (currentLabel < labels.length) {
    gotoAndPlay(labels[currentLabel]);
    currentLabel++;
  } else {
currentLabel = 0;

  shuffle(labels);  //<-if you want to re-randomize labels. otherwise, omit this line

  gotoNextLabel();


    }
}
gotoNextLabel();

• RunState.ProcessModelClient. how to access the results of markets located in the loops?

  Hello

  In my sequence, I have to perform an analysis of the results before I have the MainSequence and return to the process template. Basically, I need to check made some steps has passed.

  I access the results using RunState.ProcessModelClient. Using what I have access to the list of results. I would like to write that I have access to each result but I can't because I spotted the results of steps which are curly are not accessible (they are not there); However, they are on the report.

  How is it possible? How do I access results in a loop? Where are they?

  K.

  Hello

  not too painful:

  the loop results in the usual place online, it's just the layout that will look like a little confusing:

  You use some revisions of my TestStand (you are in 3.1)

  

  The Runstate.ProcessModelClient is actually a copy of the space of time edit, not space running - it's the SequenceFile type, which means that even if you can see the layout of the result containers that belong to each step, they are there permanently, and not filled in this place from the moment of execution.

  At the level of the mainsequence, you're still in your client, then you can go to Locals.ResultList directly.

  In there, you have the singular element that is the result of the first and the only stage of your Mainsequence of your.

  Inside there is the. TS. SequenceCall container. It is effectivey the resultlist gait that calls (always Mainsequence) seq1 so inside that, there is an another ResultList.

  It's the ResultList for sequence "Seq1".

  Which has a single item since this sequence has only one step inside of type SequenceCall.

  [0]. TS. SequenceCall.ResultList.

  From there you can see a lot of results even if you have only 4 effective steps in this sequence.

  12 results covers:

  3 iterations of ('for' 'Test2' 'end').

  and then the last 3 items are "Test1" loop 2 times more.

  When you set a stage of the loop and include you the results of each iteration, you get these results (2 in your case) more a global success-failure based on the criteria (your care ot 100% must pass in order to study the step successful when all iterations are complete.)

  Note in your pre Expression where you change the name of the step on the fly, your labeled Test2 incremental changes the name from 'Test1' + Str (Locals.LI), and the Test1 marked step uses the same expression for this will look slightly confused that you cross your results.

  Hope that helps.

  Thank you

  Sacha

• HP Pavilion: Logo and faulty drum loop

  My flag is stuck in a loop between the faulty battery alert and start HP logo. It's happened since I tried to restore the laptop. I tried all the options available, none worked and what has happened since a failed attempt to restore and delete all files. Some help would be appreciated.

  Hi @shig1,

  The ID of the failure gave me the following information:

  Fault identification label

  GLN0R3 - 6S 6869 - MFPWXF - 61SS03

  Checksum

  Ok

  Date of test

  19/07/2016

  Failure code

  307

  Device

  Storage

  Includes

  Floppy drive, hard drive, memory drive optical drive, SCSI tape drive

  Error message

  Optimized hard drive 1

  The hard drive is a failure. Back up your personal files, and you will need a hard drive replacement.

• How can I browse the labels of a cluster as if they were listed?

  It is possible to loop through the labels of a cluster like this:

  

  However, it forces me to manually maintain the chains in the structure of the case.

  Is there a way to get these labels of cluster in the structure of the case at the time of the design, similar to the use of an enum?  They're right there!

  Unfortunately not.

  You can think to use a different data structure.  If they are all the same type of data, perhaps a table works best for you.

  Another method would be to use the attributes of variant to hold the items of your cluster.  You can search for items in a variant of name it.

• Label chart in the report generator axis

  Hello

  can someone help me with my problem?

  I need to add labels of the graph axis I've done by the Builder of Labview. Is it possible to do?

  I thank very you much.

  Patrik :-)

  I guess you make the graph in Excel.  The LabVIEW Report Generation Toolkit gives you a set of 'hooks' to make an Excel chart - it actually makes an 'object' that has a limited set of formatting options, but is quick and easy to use.  If you need a more detailed field, you're probably better write an Excel macro to generate the Excel data plot, then using LabVIEW for sae data to Excel, and then run this "macro tracing' to make the fantasy plot.

  However, here's how a conspiracy "simple."  The loop For generates data that are plotted (after transposing the data to give a picture of X and an array of Y) with graphic Insert, where I also put the title of the chart.  I then specify a label for the X ("category") and value axes, ('Value') with the result the plot shown below.

  

  Bob Schor

• LabVIEW freezes randomly while loop

  Hello world

  I'm relatively new to LabView, I like to think that I learned a lot through trial and error and read this forum, but I am confused by something here. I hope someone out there has an idea.

  I have a program that controls a pump. I am communicating via a USB-serial cable. In general, how my program works is that it sends a command to the pump, and then he immediately starts querying the pump for its status. I have the query in a loop that repeats every second. While the pump is moving it returns the busy status, and when it finishes it returns to the ready state. When the program receives the ready status, it exits the application and send the following command.

  I have a Subvi, which questions the pump, and I use it in many places in my program. The problem is that all this works 95% of the time, 5% of the time the loop freezes for some reason any. The timing of this gel, location in the main program and the number of iterations of the loop that occur before the Frost are all random.

  I've attached pictures of the front panel and block diagram of the Subvi. The loop on the left is querying the pump and the Subvi in the Subvi labelled 2 is communication with the pump on the VISA. When I realized that the program has been stuck in the loop, I added the second loop (right) as a kind of "time out". If the program is blocked at this point for a specified number of seconds, it must end the left loop. But it happens, right loop stops but never left, we read the true statement and sticking. LabView itself is not frozen because I can go and the sons of the probe.

  Again, it is really difficult to solve because it occurs only 5% of the time or less. If anyone has any ideas as to why this is happening, I would be very grateful. I didn't post the real VI here would be useful, but please let me know if you want to take a peek.

  Thank you.

  PS Ce happened when executing the EXE in LabView environment

  Opening and closing of the VISA session several times are generally not a good idea.  It is preferable to configure the port outside the loop, do th ereads and written inside the loop, and then close the session after the end of the loop.  I would not be surprised if your serial port gets frozen due to the frequent opens and closes.

  In the end, you should learn about state machines.  This architecture would be appropriate for this type of program.

  Lynn

• Why this disable structure encapsulating the loop for that I'm falling?

  In the middle of coding and debugging I noticed something weird... now I'm just curious.

  Here is what happened (audio WARNING may be a bit much, fans of pumping in a warehouse im in...):

  https://www.YouTube.com/watch?v=vC9BKJ0CwmY

  I'm really just curious to know why this is happening - it seems that there is the note of "make sure wire you the error" fault behind the loop that the disable struc overlapped a bit...

  Why the struc disable that first, I dropped in this video did seize all of the loop?

  -pat

  You have this decoration of the label on your block diagram behind your loop For. When you put the new business structure, he captured this label which is outside the loop For. This forces the case structure to take the loop too, since it is the only way to recover the property node and label.

• How to save cover images everytime a loop iterates

  Then I worked on some optical codes in LabVIEW for awhile, I've read many of these similar questions but I can't seem to apply directly to my situation in all cases.

  I basically have a code that displays a graph of the intensity that is continually being modified in a loop for, I want to save a picture of the graph of the intensity of each loop without having to manually label. Y at - it something similar to the image get node that can do it. I have looked through the acquisition of the image in the screw vision but only see references to material such as cameras.

  A simplified version of a graph of changing intensity is attached. With the image of the GET, I have to put up the names of 10 images and there, the path before it will run and save as I want that there.

  1 million thanks to anyone who can help

  Hello

  You can use the iteration to create your way.

  Otherwise, you can set all paths in an array of strings.

  I ve modified your example.

  Concerning

  Yoost

• Control reference 1055 error when you use a loop for

  Hello

  I'm having a problem using control references to accomplish the following: I a VI that reads data from a text file, and then uses that automatically update the value of a control on front panel on two live different, then set the default values, and then save them. Comes from the array of control references, I tried looping on text labels until I have find the one corresponding to the order, I want to change and then update its value. The problem I have is that if I use a loop for, then 9times of LabVIEW 10 complains error 1055: "LabVIEW: object reference is not valid. If instead I the wiring to the index table and manually extract the reference, then it works every time and for each index of the reference of the order.

  Can someone take a look at my code and just see if its obvious what the problem is? In this case, I have a simple solution, but I would really like to understand what I did wrong. I have included as a code snippet, but also attached the files if that helps (Its Import_Colormap.vi, which is the problem). Persons with disabilities code fails, the active code works but I can't see what is really the difference between them - I can change the index of array 0,1,2, 3. and no mistake.

  Thank you.

  

  Your "Colormap.ctl" is a strict type def that contains a ring.  You define the elements programmatically, make the default values, and then save the "Colormap.ctl"?   I was never practicing this but here is a thread that covers this in detail. I do not understand what you expect reach by running.
  The next thing: at the same time (at the same time!), you open the Colormap.vi (this is what we see in yout PNG) that contains an instance of the Colormap.ctl on the front panel. I'm not pretty sure if LabVIEW can handle this correctly. This could be the reason why you sometimes get the error 1105.
  I prefer StringsAndValues and eventually the value of the ring running.  There is no need to do it with a def of strict type.