Standard vSwitch_Custom VM (Vlan200_VM network) port group does not.

Similar Questions

• FC Port-Channel does not

  Hello

  I need help, I'm setup CF port-channel between 9148 MDS and Cisco fabric Interconnect 6248 and the port-channel does not work. He said no operational members.

  For the MDS, see configuration below:

  NPIV #feature SW (config)

  SW (config) #feature fport-channel-trunk

  SW (config) #interface fc1/17-18

  SW(config-f) force Group-channel mode # 63

  SW(Config-if) F #switchport mode

  SW(Config-if) #switchport trunk-allowed vsan 1-2 (I have only vsan 1 and 2)

  SW (config) #no close

  SW (config) #interface 63 port channel

  SW(Config-if) F #switchport mode

  SW(config-f) #switchport trunk-allowed vsan 1-2

  SW (config) - #no close

  Note: the ports are assigned to vsan 2

  See the attached screenshots for interconnection fabric config

  On the fabric of interconnections switchport mode are defined E. What I have to change to F. If yes where can I change since the option is not there in the UCS Manager?

  have you added the VSANS on the UCSM as well?

  What Code are you runnig on the San Norhbound selector?

  You can be hitting

  https://Tools.Cisco.com/bugsearch/bug/ CSCty04686

• Port 139 does not not on Windows 7 after deployment.

  Hello

  I created some images of new installations of Windows 7. But the pack of GPO that is applied in MDT 2012 changes settings in windows 7 so that port 139 does not correctly work with gap analysis network SMB.
  recently we bought workstations that already have a Windows 7 image on them. But because computers OS was deployed hollow some imaging modalities 139 port does not work properly. Is there such a tool from Microsoft to restore the port 139 on a charge CD Windows 7 feature?
  Or any Microsoft employee who has done any research into this problem and tested and found a solution to this problem?
  Thank you.

  You can take this on the Technet forums because I don't know where the sizes are fixed. One thing to remember when the GPO is that in many cases, changes may "tattoo" the registry and must be explicitly changed back instead of be reset to the default value.

  http://social.technet.Microsoft.com/forums/en-us/category/w7itpro

  I hope this helps.

• I am connected but the network properties window does not show the size of the packets to all the

  I am connected but the network properties window does not show the size of the packets to all the

  Hi asaimas,

  You can follow this link & check if it helps:

  Configure the Option of configuring server network packet size

  Hope the helps of information.

• Control Panel is not on the list. Users and local groups does not appear in computer management.

  1. click on start, and then point to setting, control panel is not on the list.  When you try to get to the Panel of control via a link in Help and Support, had an error, "operation has been cancelled due to restrictions in effect on this computer.  Contact your system administrator. »

  2. local Users and Groups does not appear in computer management.

  There is only one profile on the PC, the OS is XP Home.  It seems lost his administrator privileges somehow my user profile.  Could you please suggest how to solve this problem?  Thanks in advance.

  Hi PJohnson,

  You can access the link below and follow the steps in the article to create a new user account and copy the data to the new account.

  http://support.Microsoft.com/kb/811151

  I hope this helps. Let us know the result.

  Thank you and best regards,

   

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Port forwarding does not work on EA6900

  Please help me to know what is the reason for this port forwarding does not work on my Linksys router:

  Model: EA6900 v1.1
  Firmware version: 1.1.42.161129

  I've set up two ports: TCP 22 and 8070 TCP to 192.168.1.10. (192.168.1.10 is up and running, I can reach the LAN ports).

  Yesterday, I had a live chat with Linksys support we tried to re - download the firmware even, but that did not help. Then factory reset and reconfigure the router did not help either.

  Unchecking "Filter anonymous Internet requests" and disable uPNP didn't help either (they have been suggested in similar topics).

  However, the IP displayed tab troubleshooting/Diagnostics reflect my external IP address (the IP displayed by http://whatismyip.com), which is weird, because I never have IP from my ISP from 100, that is displayed on the Diagnostics tab. So I guess it's a fake display or it relates to access to my router via www.linksyssamrtwifi.com ?

  Anyway I tried the two IPs from the outside, but the transfer simply doesn't work. (It works fine when I use my old router TP-Link).

  Please advise!

  Sorry guys, it seems indeed a double NAT problem. My ISP can detected MAC address change when I started using EA6900 (thinking that I couldn't not need public IP?) and since then he sends me IPs for NAT - ed. It is strange that the same day, he was working with my old router, but now it is even not working with my old router and not even working when I connect directly to my windows PC to my ISP (via PPPoE). I called their support line and they said that they will solve this problem within 72 hours. In any case, thanks for your help!

• Network adapter driver does not work with the recovery discs provided by hp

  Hello

  My wireless light does not illuminate. The network adapter driver does not install from the recovery of the driver CD.

  Here is the hardware ID. Please provide a link to the drivers:

  PCI\VEN_10EC & DEV_8176 & SUBSYS_1629103C & REV_01

  PCI\VEN_10EC & DEV_8176 & SUBSYS_1629103C

  PCI\VEN_10EC & DEV_8176 & CC_028000

  PCI\VEN_10EC & DEV_8176 & CC_0280

  Thank you

  You are the very welcome.

  It does not sound like a heat problem.

  I don't know a lot about the repair of hardware issues beyond replacement memory and hard drives.

  I could try to clean the area of fan/radiator with a can of compressed air and see if that clears any dust that may accumulate.

  To do this, disconnect the laptop from the AC adapter and remove the battery.

  Insert a rod through the air fan to keep the blades turning when you spray air.

  Spray through the air intake fan and watch to see the dust out of the exhaust.

  Repeat once or twice and blow air from the other direction of the drain line to the fan.

  The other driver, you need is the driver of protection Protectsmart hard.

  See if it works.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-116584-1&cc=us&DLC=en&LC=en&OS=4063&product=5278311&sw_lang=

• When I plug my portable hard drive to the usb port it does not read and display the contents...

  When I plug my portable hard drive to the usb port it does not read and display the contents...

  Hi deaza,.

  Ø Have you connected the USB hard drive to the computer directly or you have used an external USB hub to connect?

  O trying to connect to another USB port to check if it works?

  O the hardrive shows in windows of the computer when you connect it?

  Method 1:
  If you have installed security software, I suggest you to temporarily disable the security software and connect the USB and check to see if the same problem happens. Make sure that you enable the security software after checking.

  Alternatively, you can try to plug the USB key into a different USB port and check if it helps.

  Method 2:
  I suggest trying to launch hardware and troubleshooting of devices and check to see if it helps, here is the link:http://windows.microsoft.com/en-US/windows7/What-to-do-when-a-device-isn ' t-installed-correctly

  Method 3:
  If this does not help, then follow these steps:

  (a) remove all your USB devices. Use the safely remove the feature to turn them off.

  (b) open Device Manager and navigate to the section for USB. Uninstall all USB drives. There should be one for each USB port, and then restart.

  To open Device Manager, go to the link below and follow the steps:

  http://Windows.Microsoft.com/en-us/Windows7/open-Device-Manager

  (c) Windows should re - find all of the devices. If it is not the case, note the error message and let us know.

  You can also navigate to the link below and follow the steps to install the USB device.

  http://Windows.Microsoft.com/en-us/Windows7/install-a-USB-device

  I hope this helps. Let us know the results.

  Thank you and best regards,

  Srinivas R

  Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Auto answer for the members of the group does not

  Oracle Communications 7u4 - 27.01 (7.0.4.27.0) e-mail server 64 bit (built 30 August 2012)
  libimta.so 7u4 - 27.01 64bits (built 08:49:27, August 30, 2012)
  With the help of /u5app/opt/sun/comms/messaging64/config/imta.cnf (updated)
  
  Automatic response of users who are part of a group does not work when the email is sent to them through the email address for the group. If the email is sent directly to those users with their own email address then their autopreply work. Auto answer may work for users when they receive mail from a group address? If so, how can I go about setting up that?
  
  Thanks in advance.

  It is expected that mail sent to a list is not automatic response of the members of the list. This is explained, as well as possibly the means to get there, if you really want that in the following Article in the Knowledge MOS:

  How to configure the automatic response for members of a mailing list? (Doc ID 1511284.1)

• Automate the network port group selection in vsphere replication

  Hi, when you use the vsphere replication tool to recover servers in the data center of DR, the tool does not gives option to select network settings. I have to manually add the port groups and turn on the system remotely vcenter. Is it possible to automate this process, when the replication of a major part of the vms ~ 100-150. I would like to know if there is another way to fix the process and avoid the manual load.

  I use replication of vsphere device version 5.8

  Thank you

  The only way to automate this process is through the Site Recovery Manager.  Automate and orchestrate BC/DR is a big part of the value offered by SRM. The other advantage is the ability to test your recovery plans without disruption of service.

  Does that answer your question?

• ACS network access Restriction does not. He denies it, but allow.

  I have a problem with the restrictions of access to the network on the Group of ACS configuration.

  I configured the NAR in a group field and set it to deny access besed on client AAA, a wireless LAN controller.

  But users of this group is still able to connect wireless controller.

  Newspapers in GBA shows that the fields are right. the right user in the right of the group in good AAA client, but does not deny.

  Put in place DNIS also supports the restriction. This is how it should be configured,

  -Procedure for the configuration of NAR:

  (1) go to User Configuration---> select the user name that you want to restrict.

  2) go into Restrictions on access network (OAN) option.

  (3) by user defined network access Restrictions.

  (4) check "define CLI/DNIS-based access restrictions.

  (5) select "reject the call or Access Point.

  (6) in the dropdown AAA client list - select the name of the device on which the user does not connect.

  (7) for Port - Development *.

  (8) in CLI - use *.

  (9) for DNIS - development *.

  (10) click on submit

  Kind regards

  ~ JG

  Note the useful messages

• New for iPhone charging Port 6 does not

  Recently, I had the charging port on my iPhone replaced 6, because the original had stopped working properly. With the original, I had to shake the charger autour so he could load, but it was so bad that I could only load if I it held in place. I went to a store local tech to g

  With the new port, I am able to load it with a standard charger Apple iPhone or iPad. However, it does not charge to something else - in the car, with a cell phone charger, when it is connected to my Mac - nothing. When it is connected to these other devices, the phone doesn't even it is plugged.

  Thoughts?

  Means, "went to a store local tech to fix.

  Looking for advice!

• Support for devices on network HP service does not start

  Product: HP Photosmart Premium all-in-one (C309g)

  OS: Vista Business 32-bit

  Errors:

  When running the part 'Add a device' overall upward to add the printer to my PC, so it can be accessed without thread that appears in the background: "the specified service does not exist as an installed service."

  The result of the above process is the following message is displayed in the installation of HP screen: "the HP software that allows networking is not responding. Cancel the installation and then restart the PC. »

  As you can guess, I had this printer for some time a couple / few years at least and I did turn it wireleslly for some time.

  The printer is active on my wireless network, print the printer wireless network Test report proves. I can also access the printer Web page by entering its IP address in a web browser.

  We perceived first of all the question when the HP Solution Center reported that the printer is connected is no longer. And he suggested to do something with the installation, which sent me down the road to unintalls and installs.

  I ran printing HP and the Scan doctor, who tells me that the printer is installed for use via the USB port, but the instance networking is not installed.

  I still have the original installation CD for this printer. Run the installation off the coast of the root of the CD, I get the 'latest Version already installed"or something to that extent.  I also downloaded the latest Basic and full functionality installed on HP site.

  I used Revo Uninstaller to my uninstall and I ran CCleaner once all applications have increased from the list of programs.

  I read somewhere that it is related to the "HP network devices Support" service

  In computer management, I see that its not working do not and it is configured to start "automatically (delayed start)".

  When I try to start the service I get this: "Windows could not start the service of supported devices in HP Network on the computer local error 2: they system could not find the specified file.

  Somethings that have been made on this machine recently, I don't know when the problem of the printer started...

  Installed Quicken 2013

  ITunes installed

  Changed my home network from the Public to the private sector on this machine so I could implement the media servers.

  I check through all files updated my antivirus quarantined and it doesn't seem to be HP files in there.

  I hope my question is in fact this service, and somehow replace the missing his refferencing file will fix this.

  My next step is to uninstall once again and make sure that service falls off the list too, then reinstall HP DOWNLOAD.

  I suggest using the scrubber software integrated into the installation of clean up. The steps below will guide you through it.  Before step 10 from a CD or step 15 leave a download, check the two program folder files to make sure that the HP files are deleted.

  Of the original printer installation CD:

  1. Insert the CD in the drive and then cancel Setup

  2. open my computer and click right then on the CD from the drive and select open

  3 open the Util folder

  4 open the CCC folder

  5. run the L4.bat uninstall_ for computers not HP.  For HP computers, run the Uninstall_L3.bat

  6. once the uninstall is complete, restart the computer

  7 run the Accessories\ System Tools Disk Cleanup

  8. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  9. use this tool to clean the registry.  Note: This utility is not HP sponsored or approved.  HP and I are not responsible for damage or loss of data caused by the utility.  This step is optional.   You can skip if you want.

  http://download.CNET.com/advanced-SystemCare/3000-2086_4-10407614.HTML?part=DL-6271865&Subj=DL&tag=button

  10 download the drivers and full software features

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-73652-3&cc=us&DLC=en&LC=en&OS=2093&product=3793676&sw_lang=

  11 start the download to reinstall the printer

  Starting a download:

  1. run the disk cleanup on your computer

  2. download and run the software and the drivers below.

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-73652-3&cc=us&DLC=en&LC=en&OS=2093&product=3793676&sw_lang=

  3. once the download is done retrieve, cancel the download.

  4. click on the start menu.

  5. click on run.

  6. type %temp% enforcement

  7. Locate and open the folder starting with 7z (example: 7zS2356)

  8 open the Util folder

  9 open the CCC folder

  10. run the L4.bat uninstall_ for computers not HP.  For HP computers, run the Uninstall_L3.bat

  11. once the uninstall is complete, restart the computer

  12 run the Accessories\ System Tools Disk Cleanup

  13. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  14 use this tool to clean the system and the registry.  Note: This utility is not HP sponsored or approved.  HP and I are not responsible for damage or loss of data caused by the utility.  This step is optional.   You can skip if you want.

  http://download.CNET.com/advanced-SystemCare/3000-2086_4-10407614.HTML?part=DL-6271865&Subj=DL&tag=button

  15 download the drivers and full software features

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=MP-73652-3&cc=us&DLC=en&LC=en&OS=2093&product=3793676&sw_lang=

  16. run the download to reinstall the printer

• N2048 port security does not

  Hi Experts,

  Only, we have deployed a new site that uses the Dell N2048 switches in a stack.

  Now we would add port security to the switch, Port-MAC locking to lockdown one port if another computer.

  According to the manual, to put in place we only need of to the port to locked under the MISTLETOE under switching, network security, port security.

  This does not activate it.

  We tried to add via the command line, in the ports of test, it now shows:

  switchport security of dynamic ports 1

  Still, port security is not enabled. There is another thing that must be enabled in the world to do this job or other commands?

  Thank you

  The output of port security-# show is as follows:

  Port Security Administration Mode: enabled

  It is possible that the tests were not done fast enough. I spent the time-out and ask them to test again.

  Thank you

• Several networks in cryptomap does not.

  Hello.

  I have 1 ASA 5505 to a site and a 5510 on another site... I have 4 5510 subnets on different interfaces.

  I have a vpn between the 2 ASA´s, and on the 5510, LAN is defined as all subnets that I want access.

  I have the 5505 subnets in the remote network.

  But when I want to access the network via vpn... He used...

  The link is pointing upwards, but under the SMDA, vpn and details connections monitor. I don't see one of the nets of the encryption card.

  and I can just ping on this net.

  If I do a trace of package on the net in the details. I can see that it delivers it via vpn, if I try an other nets. He road via vpn.

  the DM_INLINE_NETWORK_1 object-group network
  object-network 172.26.1.0 255.255.255.0
  object-network 172.26.2.0 255.255.255.0
  network-object 172.28.0.0 255.255.248.0
  object-network 192.168.0.0 255.255.255.0
  access extensive list ip 192.168.173.0 whatsup_nat0_outbound allow 255.255.255.0 192.168.0.0 255.255.255.0
  access extensive list ip 192.168.173.0 outside_4_cryptomap allow 255.255.255.0 DM_INLINE_NETWORK_1 object-group

  Another question.

  How to allow ping the address of the interface of the other interfaces... That is to say on the interface.

  And the last one...

  Is it possible to do a static nat from one single interface KR Int1 192.168.100.10-> Int2-> 10.10.10.10 and then connect to Int1, int3 192.168.100.10 20.20.20.20?

  / Rene

  Hello

  The reason why this does not work is because the NAT-0 rule you

  configured.

  the DM_INLINE_NETWORK_16 object-group network

  object-network 192.168.0.0 255.255.255.0

  network-object nitron 255.255.255.0

  object-network dmz_zone 255.255.255.0

  Access extensive list ip 172.26.0.0 MPLS_nat0_outbound allow 255.255.252.0

  DM_INLINE_NETWORK_16 object-group

  NAT (MPLS) 0-list of access MPLS_nat0_outbound

  In the above lines, you can see that 172.26.0.0/22 will UN-natted to

  subnet 192.168.0.0/24 (inside). SHEEP rule takes precedence over the static NAT.

  So, you are not able to connect using 192.168.0.199 address. Please insert

  the following lines in your configuration:

  MPLS_nat0_outbound of access list 1 line deny host ip 172.26.2.5 all

  allow the ip host 172.26.2.5 access list pnat1 a

  allow the ip host 172.26.2.5 access list pnat2 a

  not static (MPLS, inside) 192.168.0.199 172.26.2.5 netmask 255.255.255.255

  static (MPLS, inside) 192.168.0.199 access list pnat1

  static (MPLS, inside) 172.26.2.5 pnat2 access list

  I hope this helps.

  Kind regards

  NT