Lrt224 direct traffic through ports wan by device

Similar Questions

• VPN traffic through incoming port

  On my ASA 5510 I want for the VPN clients can connect on the outer harbour and have their internet traffic directed back on that same port, with the internal traffic inside port.  Is this possible?  If so, how does do this?

  Will be transmitted traffic VPN based on the routing table after out of the tunnel.

  If you do not want to let Internet traffic to turn on the external interface, you must add

  -permit same-security-traffic intra-interface

  -make the Association NAT change such as

  Global interface 4 (external)

  NAT (outside) 4

• RV 320 won't internet traffic through the SMC modems

  We have recently installed a RV320 to use primarily as a gateway for FTP traffic. The router is installed power 2 60/10 circuits of our Internet service provider who provided 2 edge of the MSC devices and which have Wifi capabilities and router. When connect on modems in factory default state the RV320 connects but does not take advantage of the double connections in terms of speed. When disable us the wifi modems and router running the RV 320 connects but do not traffic through to the modems.

  Since the two modems are identical, we get the same news IP and gateway of each. I would prefer not to have the modem in router mode. Is there a setting on the RV that will connect and pass internet traffic with modems in mode 'dumbed down '.

  Graham Saywell

  Wanted to sound and image

  Toronto

  Hi Graham,

  The best scenario is to have both SMC routers on bridge mode and configure both on RV320 WAN interface with (PPPE, static IP, DHCP... He expense of your WAN connection)

  Can you please share with us what kind of WAN connection you use in the SMC routers?

  -Ensure the RV320 you have the latest firmware 1.1.0.09, otherwise you can download it from this link:

  http://software.Cisco.com/download/release.html?mdfid=284005929&softwareid=282465789&release=1.1.0.09&relind=available&rellifecycle=&RelType=latest

  -On RV320 under the management of the system--> Dual WAN and check Load Balance

  -After that, you set up the RV320 with the same type of WAN connection as a router SMC and SMC router mode Bridge and in this case, you should see the two public IP on RV320 of audit system summary

  If you do these steps and still you can not the public IP address RV320 and the SMC router in Bridge mode, please share with us the configuration file RV320 and screenshots of two CMS about the WAN configuration

  If in the case the SMC router does not have the option of working in Bridge mode, in this case, you will need to have the local of the SCM with subnet different e.g. 192.168.1.1/24 and other a 192.168.2.1/24

  on RV320 you can leave the configuration in DHCP on both WAN Ondaaah (if you have the DHCP Server enable SMC router) or you can configure the static IP address on the two wan

  * Please answer question mark or note the fact other users can benefit from the TI *.

  Thank you

  Mehdi

• Connect (2) s RV082 directly to simulate the WAN?

  Does anyone know if this is possible and how I need to set this up? I would like to create VPN Tunnel directly between 2 interfaces to simulate WAN it operating on the internet.

  Thank you

  Joe

  Hello!

  I think you should make some corrections in the parameters of intellectual property:

  Router 1:

  WAN IP ADDRESS: 10.10.10.1

  Subnet mask: 255.255. 0.0

  Default gateway: 10.10.20.1

  Primary and secondary DNS: do not necessary

  LAN IP: 192.168.1.1

  Subnet mask: 255.255.255.0

  Router 2:

  WAN IP: 10.10.20.1

  Subnet mask: 255.255. 0.0

  Default gateway: 10.10.10.1

  Primary and secondary DNS: do not necessary

  LAN IP: 192.168.2.1

  Subnet mask: 255.255.255.0

  Please, pay attention to the ports WAN subnet mask - it should be 255.255.0.0, other wise with an old a WAN IP 255.255.255.0 in the subnet that is different and may not have a direct connection.

• High utilization of the processor in Mode VSS when traffic through the internet.

  Hi all

  I have a problem with the installation of VSS. The VSS service install act as a central office switch of transit for internet traffic and the problem arises when there are about 600 Mbps of traffic through the switch. We notice that there are a lot of packages being softswitch and the rate is quite high, almost like 100 to 200 k per second.

  The VSS switch manages ospf and BGP and have plenty of internet routing. After investigation of high CPU usage, I noticed that the AAGR switch is full and has tried to set the course of max mls to the maximum cef and restarted the VSS service.

  Unfortunately, the problem persists after restarting.

  We had planned to filter the full internet routes and enable by default and ospf route only in the VSS service and restart the VSS service to make sure that the table AAGR is not overloaded.

  If I fail the next step is to return to autonomous mode and hope that the processor will not pull up.

  My Question: These step will prevent the issue? Suggestions or the reference similar to the problem I am facing in?

  Hello Sophie,.

  unless you have a PFC 3CXL and all the DFCs the AAGR 3CXL can manage only 256 000 IP prefixes and nowdays that complete a table is in order or 310-320 000 routes.

  See

  http://www.Cisco.com/en/us/prod/collateral/switches/ps5718/ps9336/product_data_sheet0900aecd806ed759_ps708_Products_Data_Sheet.html

  http://www.Cisco.com/en/us/prod/collateral/switches/ps5718/ps708/product_data_sheet09186a0080159856.html

  See table 1 in the second link it tells what I wrote in the first line.

  > We planned to filter the full internet routes and enable by default and ospf route only in the VSS service and restart the VSS service to make sure that the table AAGR is not overloaded.

  You should not need the device after accepting only the default route in OSPF or BGP AAGR use will be greatly reduced this is just wait a few minutes (unless there is an underlying SW bug) for the MSFC to update CFP and then all DFCs

  Hope to help

  Giuseppe

• no tab port in XP Device Manager

  Adding a printer to add a printer, and when it gets to the tab port selection, there is no sheer USB001, only Com and Lpt, port...

  where the selection of the USB port,

  There is no tab port in the Device Manager either...

  win xp pro sp3

  HELP PLEASE

  Adding a printer to add a printer, and when it gets to the tab port selection, there is no sheer USB001, only Com and Lpt, port...

  where the selection of the USB port,

  There is no tab port in the Device Manager either...

  win xp pro sp3

  HELP PLEASE

  Your question is confusing.

  What is the Device Manager has to do with your question?

  You have the printer driver on CD-ROM or downloaded?

  If you mean there is no entry in the drop-down list, as shown in this image: http://screenshots.modemhelp.net/screenshots/Windows_XP/Printers/Add_Printer/03_%28Local%29/01_%28Use_Port%29_%28Select%29.shtml then you need to check the "Create a new port" to create the USB port.  Especially with HP printers, however, it is preferable to use the installation software as HP uses a USB port to measure.

• WRT 1900 ACS - Impossible to carry web traffic through openvpn

  2.3.11 OpenVPN windows 7 X 86. Router information

  Firmware version:	1.0.0.169041
  Serial number:	18E1060B503339

  By default, OpenVPN only sends traffic over the VPN, which is intended for the VPN. Normal traffic to Web sites, for example, is not sent by the VPN. Which can be modified to send all traffic through the VPN?

  @alexdemon

  Router WRT1900ACS is a SOHO router. It doesn't have a feature of access rule where the web traffic can be managed and regulated. The tool of Parental control of your Linksys Smart Wi - Fi account is designed for local customers only.

  Note:

  OpenVPN can create the tunnel from the remote host to the main network and thus web traffic cannot be routed through the router firewall.

  Ann_18678
  Linksys technical support

• Traffic that overlap on the device with the power of fire

  Hello world

  How should I handle the traffic that overlap on the device of firepower?

  I am inspection 2 VLANS using switches virtual, one VLAN is my edge of the internet and the other VLAN is my internal servers VLAN.

  Sometimes my internal servers to THAT VLAN needs access to internet and that traffic is superimposed on the inspection of my internet edge VLAN.

  Is there a configuration to avoid connections between connected/inspected twice?

  Thank you

  Hello

  You can create rule of the trust with areas / vlan specific or IP source/destination if you want a specific traffic does not inspect.

• Impossible to pass traffic through the VPN tunnel

  I have an ASA 5505 9.1 running.   I have the VPN tunnel connection, but I am not able to pass traffic. through the tunnel. Ping through the internet works fine.

  Here is my config

  LN-BLF-ASA5505 > en
  Password: *.
  ASA5505-BLF-LN # sho run
  : Saved
  :
  : Serial number: JMX1216Z0SM
  : Material: ASA5505, 256 MB RAM, 500 MHz Geode Processor
  :
  ASA 5,0000 Version 21
  !
  LN-BLF-ASA5505 hostname
  domain lopeznegrete.com
  activate the password
  volatile xlate deny tcp any4 any4
  volatile xlate deny tcp any4 any6
  volatile xlate deny tcp any6 any4
  volatile xlate deny tcp any6 any6
  volatile xlate deny udp any4 any4 eq field
  volatile xlate deny udp any4 any6 eq field
  volatile xlate deny udp any6 any4 eq field
  volatile xlate deny udp any6 any6 eq field
  passwd
  names of
  !
  interface Ethernet0/0
  switchport access vlan 2
  !
  interface Ethernet0/1
  !
  interface Ethernet0/2
  !
  interface Ethernet0/3
  !
  interface Ethernet0/4
  !
  interface Ethernet0/5
  !
  interface Ethernet0/6
  !
  interface Ethernet0/7
  !
  interface Vlan1
  nameif inside
  security-level 100
  IP 192.168.116.254 255.255.255.0
  OSPF cost 10
  !
  interface Vlan2
  nameif outside
  security-level 0
  IP 50.201.218.69 255.255.255.224
  OSPF cost 10
  !
  boot system Disk0: / asa915-21 - k8.bin
  passive FTP mode
  DNS server-group DefaultDNS
  domain lopeznegrete.com
  network obj_any object
  subnet 0.0.0.0 0.0.0.0
  the LNC_Local_TX_Nets object-group network
  Description of internal networks Negrete Lopez (Texas)
  object-network 192.168.1.0 255.255.255.0
  object-network 192.168.2.0 255.255.255.0
  object-network 192.168.3.0 255.255.255.0
  object-network 192.168.4.0 255.255.255.0
  object-network 192.168.5.0 255.255.255.0
  object-network 192.168.51.0 255.255.255.0
  object-network 192.168.55.0 255.255.255.0
  object-network 192.168.52.0 255.255.255.0
  object-network 192.168.20.0 255.255.255.0
  object-network 192.168.56.0 255.255.255.0
  object-network 192.168.59.0 255.255.255.0
  object-network 10.111.14.0 255.255.255.0
  object-network 10.111.19.0 255.255.255.0
  the LNC_Blueleaf_Nets object-group network
  object-network 192.168.116.0 255.255.255.0
  access outside the permitted scope icmp any4 any4 list
  extended outdoor access allowed icmp a whole list
  outside_1_cryptomap list extended access permitted ip object-group LNC_Blueleaf_Nets-group of objects LNC_Local_TX_Nets
  inside_nat0_outbound list extended access permitted ip object-group LNC_Blueleaf_Nets-group of objects LNC_Local_TX_Nets
  LNC_BLF_HOU_VPN list extended access permitted ip object-group LNC_Blueleaf_Nets-group of objects LNC_Local_TX_Nets
  pager lines 24
  Enable logging
  asdm of logging of information
  Within 1500 MTU
  Outside 1500 MTU
  no failover
  ICMP unreachable rate-limit 1 burst-size 1
  ASDM image disk0: / asdm - 741.bin
  don't allow no asdm history
  ARP timeout 14400
  no permit-nonconnected arp
  !
  network obj_any object
  NAT dynamic interface (indoor, outdoor)
  outside access-group in external interface
  !
  router ospf 1
  255.255.255.255 network 192.168.116.254 area 0
  Journal-adj-changes
  default-information originate always
  !
  Route outside 0.0.0.0 0.0.0.0 50.201.218.94 1
  Timeout xlate 03:00
  Pat-xlate timeout 0:00:30
  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
  timeout tcp-proxy-reassembly 0:01:00
  Floating conn timeout 0:00:00
  dynamic-access-policy-registration DfltAccessPolicy
  identity of the user by default-domain LOCAL
  the ssh LOCAL console AAA authentication
  AAA authentication enable LOCAL console
  Enable http server
  http 192.168.2.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  Server enable SNMP traps snmp authentication linkup, linkdown cold start
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
  Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
  Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
  Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
  Crypto ipsec pmtu aging infinite - the security association
  card crypto outside_map 1 match address outside_1_cryptomap
  peer set card crypto outside_map 1 50.201.218.93
  card crypto outside_map 1 set transform-set ESP-3DES-SHA ikev1
  outside_map interface card crypto outside
  Crypto ca trustpoint _SmartCallHome_ServerCA
  no use of validation
  Configure CRL
  trustpool crypto ca policy
  Crypto ca certificate chain _SmartCallHome_ServerCA
  certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
  308204 4 a0030201 d 308205ec 0202106e cc7aa5a7 032009b 8 cebcf4e9 52d 49130
  010105 05003081 09060355 04061302 55533117 ca310b30 0d 864886f7 0d06092a
  30150603 55040 has 13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b
  13165665 72695369 676e2054 72757374 204e6574 776f726b 313 has 3038 06035504
  0b 133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72
  20617574 7a 656420 75736520 6f6e6c79 31453043 06035504 03133c 56 686f7269
  65726953 69676e20 436c 6173 73203320 5075626c 69632050 72696 72792043 61 d
  65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31
  30303230 38303030 3030305a 170d 3230 30323037 32333539 35395a 30 81b5310b
  30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20
  496e632e 311f301d 06035504 0b 131656 65726953 69676e20 54727573 74204e65
  74776f72 6b313b30 5465726d 20757365 20617420 73206f66 39060355 040b 1332
  68747470 7777772e 733a2f2f 76657269 7369676e 2e636f6d 2f727061 20286329
  302d 0603 55040313 26566572 69536967 61737320 33205365 6e20436c 3130312f
  63757265 20536572 76657220 20473330 82012230 0d06092a 864886f7 4341202d
  010101 05000382 010f0030 82010 0d has 02 b187841f 82010100 c20c45f5 bcab2597
  a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10
  9c688b2e 957b899b 13cae234 34c1f35b f3497b62 d188786c 83488174 0253f9bc
  7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b
  15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845
  1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8 63cd
  18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced
  4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f
  81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 01 has 38201 02030100 df308201
  082b 0601 05050701 01042830 26302406 082 b 0601 db303406 05050730 01861868
  7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1 d 130101
  ff040830 02010030 70060355 b 200469 30673065 060, 6086 480186f8 1 d 060101ff
  45010717 03305630 2806082b 06010505 07020116 1 c 687474 70733a2f 2f777777
  2e766572 69736967 6e2e636f 6d2f6370 73302 has 06 082 b 0601 05050702 02301e1a
  1 c 687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406
  03551d1f 042d302b 3029 has 027 a0258623 68747470 3a2f2f63 726c2e76 65726973
  69676e2e 636f6d2f 2d67352e 70636133 63726c 30 0e060355 1d0f0101 ff040403
  02010630 6d06082b 06010505 07010c 59305730 55160969 5da05b30 04 61305fa1
  6 d 616765 2f676966 3021301f 2b0e0302 30070605 1a04148f e5d31a86 ac8d8e6b
  c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973
  69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30
  1 b 311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301D 0603
  445 1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355 c 1604140d 551d0e04
  1 230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300 d 0609 d
  2a 864886 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80 f70d0101
  4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e
  b2227055 d9203340 3307c 265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a
  99 c 71928 8705 404167d 1 273aeddc 866d 24f78526 a2bed877 7d494aca 6decd018
  481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16
  b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0
  5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8
  6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28
  6c2527b9 deb78458 c61f381e a4c4cb66
  quit smoking
  crypto isakmp identity address
  Crypto isakmp nat-traversal 1500
  Crypto ikev1 allow outside
  IKEv1 crypto policy 10
  preshared authentication
  aes-256 encryption
  sha hash
  Group 5
  life 86400
  IKEv1 crypto policy 65535
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400
  Telnet timeout 5
  SSH stricthostkeycheck
  SSH 0.0.0.0 0.0.0.0 inside
  SSH 0.0.0.0 0.0.0.0 outdoors
  SSH timeout 5
  SSH version 2
  SSH group dh-Group1-sha1 key exchange
  Console timeout 0
  management-access inside

  a basic threat threat detection
  Statistics-list of access threat detection
  no statistical threat detection tcp-interception
  attributes of Group Policy DfltGrpPolicy
  Ikev1 VPN-tunnel-Protocol l2tp ipsec without ssl-client
  username
  username
  tunnel-group 50.201.218.93 type ipsec-l2l
  IPSec-attributes tunnel-group 50.201.218.93
  IKEv1 pre-shared-key *.
  NOCHECK Peer-id-validate
  !
  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  maximum message length automatic of customer
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the netbios
  inspect the rsh
  inspect the rtsp
  inspect the skinny
  inspect esmtp
  inspect sqlnet
  inspect sunrpc
  inspect the tftp
  inspect the sip
  inspect xdmcp
  Review the ip options
  !
  global service-policy global_policy
  context of prompt hostname
  call-home service
  anonymous reporting remote call
  call-home
  contact-email-addr [email protected] / * /
  Profile of CiscoTAC-1
  http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
  email address of destination [email protected] / * /
  destination-mode http transport
  Subscribe to alert-group diagnosis
  Subscribe to alert-group environment
  Subscribe to alert-group monthly periodic inventory
  monthly periodicals to subscribe to alert-group configuration
  daily periodic subscribe to alert-group telemetry
  Cryptochecksum:e519f212867755f697101394f40d9ed7
  : end
  LN-BLF-ASA5505 #.

  Assuming that you have an active IPSEC security association (i.e. "show crypto ipsec his" shows the tunnel is up), please perform a packet trace to see why it's a failure:

   packet-tracer input inside tcp 192.168.116.1 1025 192.168.1.1 80 detail

  (simulating a hypothetical customer of blue LNC tries to navigate to a hypothetical LNC TX Local site server)

• Enable PPTP through a Cisco ASA device

  I have a Cisco ASA and ISA 2004 server.

  I want to use ISA as a VPN server. So, I need the ASA to allow the

  PPTP VPN traffic through the ISA Server computer so that it can authenticate.

  Can someone help me how to set up.

  Only tcp... If you have an access list applied to the inside interface... Then, you need to add

  access-list extended permitted will host all

• An ASA inspect traffic through a VPN?

  The ASA did inspect the traffic through a VPN using the default inspect the rules?

  Hi Justin,

  The SAA can inspect traffic encryption before or after decryption. The ASA cannot inspect encrypted traffic.

  This means that if the VPN tunnel ends on the ASA, ASA can inspect traffic sent through the prior encryption tunnel and could inspect the traffic post decryption when received.

  If the tunnel is not over on the SAA but pass instead through the ASA, ASA cannot inspect traffic encapsulated inside.

  It will be useful.

  Federico.

• Configuration of the router to allow VPN traffic through

  I would like to ask for assistance with a specific configuration to allow VPN traffic through a router from 1721.

  The network configuration is the following:

  Internet - Cisco 1721 - Cisco PIX 506th - LAN

  Remote clients connect from the internet by using the Cisco VPN client. The 1721 should just pass the packets through to the PIX, which is 192.168.0.2. Inside of the interface of the router is 192.168.0.1.

  The pix was originally configured with a public ip address and has been tested to work well to authenticate VPN connections and passing traffic in the local network. Then, the external ip address was changed to 192.168.0.2 and the router behind.

  The 1721 is configured with an ADSL connection, with fall-over automatic for an asynchronous connection. This configuration does not work well, and in the local network, users have normal internet access. I added lists of access for udp, esp and the traffic of the ahp.

  Cisco VPN clients receive an error indicating that the remote control is not responding.

  I have attached the router for reference, and any help would be greatly apreciated.

  Manual.

  Brian

  For VPN clients reach the PIX to complete their VPN the PIX needs to an address that is accessible from the outside where the customers are. When the PIX was a public address was obviously easy for guests to reach the PIX. When you give the PIX one address private, then he must make a translation. And this becomes a problem if the translation is dynamic.

  You have provided a static translation that is what is needed. But you have restricted the TCP 3389. I don't know why you restricted it in this way. What is supposed to happen for ISAKMP and ESP, AHP traffic? How is it to be translated?

  If there is not a static translation for ISAKMP traffic, ESP and AHP so clients don't know how to reach the server. Which brings me to the question of what the address is configured in the client to the server?

  HTH

  Rick

• Send all traffic through the vpn tunnel

  Does anyone know how to send all traffic through the tunnel vpn on both sides?  I have a server EZVpn on one side and one EZVpn client on the other.  I'm not natting on each side.  I use the value default 'tunnelall' for the attributes of group policy.  On the client side all traffic, even if not intended for the subnet of the side server, seems to pass through the tunnel.  But if I ping the side server, the same rules don't seem to apply.  Traffic destined for rates aside customer through the tunnel, but the traffic that is not pumped on the external interface in the clear.  That's not cool.

  Hello

  Clinet traffic to server through tunnel, that's right, right?

  Traffic from server to client through tunnel, but the rest of the traffic is not, no?

  This works as expected because in ezvpn, politics of "tunnel all ' is for traffic is coming from the client., do not leave the server.

  Side server, customer traffic will pass through tunnel, the rest used.

  Sian

• With direct supply through Griffin PowerBlock load LifeDrive. Can it be done?

  I don't like having to recharge the LifeDrive via USB to the computer.  So, I got this usb Griffin powerblock that I use to power my Zune player.  The power plug match the power of the LifeDrive specs.  I was wondering if it would FRY my LifeDrive by connecting the side usb in usb - next to the power supply powerblock.  I ask because I see other sites that the connector end of the power (the LifeDrive) is small and NOT like that of the connector used for power and synchronization via usb only.

  A bit simpler: the powerblock I plugs into the wall and the usb cable plugs into it.  I'm afraid that somehow power not only to feed the correct contacts (to load), but power also to other contacts that synchronize the device to the computer, effectively blowing my LifeDrive.

  Someone at - it experience with this dilemma?

  Thanks again

  Message edited by sirzune on 07/10/2008 10:42

  If you connect the USB cable into another USB port then the device should be OK. USB standards means the function of each axis in the conector and tensions, they are universal for any cable USB/port.

  You can do a search on Google for a power running to your lifedrive.

  I found one on ebay.

  http://CGI.eBay.com/AC-wall-charger-for-Palm-LifeDrive-%2f-Treo-650-700p-700w_W0QQitemZ300264027458QQcmdZViewItemQQimsxZ20081005?IMSfp=TL081005107003r23611

  Message relates to: Palm i705

• CISCO RV180 - filter on Port WAN MAC

  Hello!

  I have configured the VPN tunnel between the main and remote desktop by using two routers RV180. I also created some additional users so personal is not in one of above mentioned offices can use the VPN from their Windows or Linux laptops and connect to the corporate network. Everything is defined.

  Miss me only now an option to connect to mobile devices like the iPhone or iPad so that they can connect and discovers the company web server internal too. Other devices with MAC addresses that are not those don't connect using their software operating system by default, so I had an idea to pass through the router port 443 to the internal web server, but somehow her filter by MAC addresses, i.e. If a person with a certain MAC address connects to WAN it gets transmitted , gets denied. Is this possible with our RV180 router?

  Slava,

  It is not possible to filter by MAC address. You can filter by IP address by creating an access rule, but you must know the IP WAN address that users will connect. Are they all in the same place and it has a WAN IP address, it would work well.

  -Marty