Connect (2) s RV082 directly to simulate the WAN?

Similar Questions

• Internet does not connect unless it is directly connected to the computer

  This problem occurred yesterday.

  Internet has suddenly stopped working. Things were going to turn power off, then on and distributed. I did check the lights on the modem and the router, but they were all working well. I have plugged on both computers. This does not solve it. I called Charter to see if there was a failure. Unfortunately, it's a message auto troubleshooting which I have materialized with. He had me hang my modem directly to my computer. This solved my problems of the internet.

  I went to sleep for the night in the hope that the internet, or what the question was, would fix itself. He did not. The internet still works only if it is directly connected to the computer.

  There are other people who need to use the internet here. (Invoices, work schedules and other) So maybe it's very much a problem. Any other computer or phone, will work in the House.

  What is a router problem or a cable, or...?

  If your connection works when you plug the modem but not through the router, this indicates a problem with the router.   This could be a hardware failure or a configuration problem.  A problem with the cable between the modem and the WAN port on the router is possible, but unlikely.  It wouldn't hurt to check if she.  Most routers have a reset button recessed.  I suggest that you reset the router and reinstall as if new.  If this fails, you probably need to replace the router.

  Depending on your technical knowledge, you can also log in to the router and check the status information.

• No option to simulate the peripheral cRIO after installing Labview and RT/FPGA Modules of downloads (lack of driver support?)

  Hi guys -.

  Basically, I need to simulate a cRIO device without yet having equipment on-site, like this:

  How to simulate the FPGA hardware target using with LabVIEW Project Explorer

  Instead, I only get the options presented in the attachment "Add Target Options.jpg.  I guess it's because of missing drivers, which I assume is due to an error that I made during a recent new LV installation installation went like this: I downloaded (not diskettes) and installed the following (in this order, the latest versions all around):

  (1) LabView development system

  (2) real-time module

  (3) FPGA module

  (4) NEITHER-RIO (previous installation-by-installation)

  (5) DAQmx

  At the end of (1) and (2), I got the screen shown in the second attachment ("Drivers Installer Message.jpg"), but could not able to recognize the folder "device drivers OR" (I also downloaded), or one of its subfolders.

  According to me, I'm missing an obvious option to load the necessary drivers after installation, but can't seem to find reference to it in the forums.  Could someone give me a little help in the right direction?

  Thanks a lot and have a nice day.

  
  

• HP Envy 15 j140en: HP Envy connection as an administrator, just white screen the mouse cursor

  Hi all

  A new laptop had delivered today.  I have installed various software that I use and everyuthing was fine for a few hours that I have installed various bit of this and that.

  Then, all of a sudden I have connection and after my password entry screen, the laptop just hangs with the mouse cursor.

  BUT, I created a non admin user and it "s all very well.

  I tried various fixes I found online, including some here, but nothing seems to work.

  It is a unit refurbed FYI direct to laptops.

  Thanks in advance for any help.

  Carl

  Hello

  Yes, a system restore solved all this.   :-)

  Thank you

• HP Pro Plus 6800: error 0 x, 00000057 wireless and wireless Direct properties of the Windows Control Panel printer - print a Test Page

  I have a laptop Toshiba Satellite of Win7 64 bit and a HP 8600 Pro Plus,
  update firmware and drivers about 2 weeks for the 8600 was a
  a long time I have been updated, which is connected wireless has decided to
  Direct to print Wireless Setup once the program installation, I tried to do a windows
  Print the Test Page in the printer property Panel, somewhat normal for
  set up a printer

  Under the connection of the conciergerie, I got the error message 0 x 00000057
  Under wireless direct printing, I got the same error 0 x 00000057

  After spending the time to check the settings, connections and asking
  Why? I decided to see that if I could print the docs, I print a PDF file,
  Notepad and Word documents in each application under the two
  configurations without problem.

  Under the wireless connection, I started the Web Services module
  and was able to make the impression within the Web Services Test page
  module without problem could not yet do the printing Test Page
  in the printer properties panel.

  I ran Print and Scan doctor who, to my surprise mentioned
  a conflict of Driver, I welcomed this program to uninstall the driver,
  went looking upward for the driver and the same driver was so done
  No download but to remove the driver and reinstalled the driver.
  Always error message here.

  I'm now tempted to delete a direct print wireless and see
  What happens if the error disappears, if she does not unstall all
  associated with the printer and do a clean reinstall. In case of emergency
  is there an alternative to the use of the Web Service module to the setting
  When not connected to the wireless network?

  I think that the Panel of the printer would do this (I'll watch this later

  spend enough time on it), or do I need to run Web Services to

  direct wireless installation, just think about this, otherwise I'll shoot

  a usb cable.  Maybe if I install Direct wireless on the printer control panel

  the message will disappear as the installation of the printer program, not software

  on the laptop?

  It is a minor problem since I can still print but question why!

  See other issues about this error message I thought

  spend my experience with this error.

  Always had a number of things to think and try, once again.

  If your getting this error message I would suggest trying a test page printed

  within the module of Web Service to see if the message developed.

  Could not back the driver so I removed the printer driver

  by deleting.

  19/07/2011 Date print driver
  Print driver version 26.0.0.0

  and removed software in Add and Remove software Hp also had to turn

  disable the wireless module directly on the printer to reinstall from the CD.

  Reinstalled printer/software form the CD supplied with the printer, the

  Driver date is 08/12/2009 Ver.9.0.0

  No more error in configuration.

  is the answer to the error message 0 x 00000057 or 0x00000xx

  associated with the driver? Or just the 0 x 00000057?

  Could not find a list of drivers between the driver and

  the driver on the CD.

  Will not update the driver for a good while or until I have too.

  The dates on the drivers are only about two years apart, the

  The version numbers are an issue questable.

• LRT224 hickups: abandon the WAN connection?

  Hello

  my new LRT224 shows hickups in my regard.

  It is connected to a fiber-optic 100Mbps of my ISP connection.

  If I try to stream video, it creates every minute or so a second or two to break up the transmission.

  Obviously, this breaks my video stream.

  The newspaper of the device (see below), says 'WAN connection fell', which seems rather strange and unexpected for me.

  If I don't stream video and data binding is almost at rest, these messages of 'WAN fell' intermittent continue.

  If I take the LRT outside and connect my PC directly to the line of ISP (Yes, bad practice) I don't have these hickups, and fine video streams (to a few Mbps).

  I have updated the firmware to v1.0.1.01 but that has not made a difference.

  In fact, I have disabled the 2nd WAN port.

  "Dual WAN', the 'activate the Network Service detection' is not marked in the config. By selecting "Connection failover" or "Load balance" shows no difference (no improvement).

  No idea why the LRT report "WAN connection is dropped?

  I need urgently a solution, but the issue seems beyond my skills...

  (In the newspaper, I also see "violation of policy. I don't know why they happen: I have no rules of firewall on the LAN or WAN IP addresses...)

  Thanks for any idea!

  Jos

  He is a legend of the newspaper of the device:

  Feb 26 18:28:37 2014  System Log  WAN connection is down
  Feb 26 18:28:38 2014     System Log  WAN connection is up : 5.199.147.151/255.255.240.0 gw 5.199.144.1 on eth1
  Feb 26 18:30:51 2014     Connection Refused - Policy violation  TCP 192.168.1.106:55059->173.192.114.54:7031 on eth1
  Feb 26 18:30:58 2014     Connection Refused - Policy violation  TCP 192.168.1.108:65516->89.248.168.42:3129 on eth1
  Feb 26 18:31:33 2014     System Log  WAN connection is down
  Feb 26 18:31:34 2014     System Log  WAN connection is up : 5.199.147.151/255.255.240.0 gw 5.199.144.1 on eth1
  Feb 26 18:31:36 2014    ACCESS_RULE TCP 192.168.1.107:65516->157.55.56.153:3129 on eth0
  Feb 26 18:31:37 2014     Connection Refused - Policy violation  TCP 192.168.1.106:55159->199.9.249.46:1935 on eth1
  Feb 26 18:31:37 2014     Connection Refused - Policy violation  TCP 192.168.1.106:55158->199.9.249.46:1935 on eth1
  Feb 26 18:31:37 2014    ACCESS_RULE TCP 192.168.1.107:55158->157.55.56.153:1935 on eth0
  Feb 26 18:31:51 2014     Connection Refused - Policy violation  TCP 192.168.1.106:55059->173.192.114.54:7031 on eth1
  Feb 26 18:32:50 2014     System Log  WAN connection is down
  Feb 26 18:32:51 2014     Connection Refused - Policy violation  TCP 192.168.1.108:49527->78.235.240.121:57236 on eth1
  Feb 26 18:32:51 2014     System Log  WAN connection is up : 5.199.147.151/255.255.240.0 gw 5.199.144.1 on eth1
  Feb 26 18:33:51 2014     Connection Refused - Policy violation  TCP 192.168.1.106:55059->173.192.114.54:7031 on eth1
  Feb 26 18:33:58 2014     Connection Refused - Policy violation  TCP 192.168.1.108:49374->89.248.168.42:3129 on eth1
  Feb 26 18:34:51 2014     Connection Refused - Policy violation  TCP 192.168.1.106:55059->173.192.114.54:7031 on eth1
  Feb 26 18:34:59 2014     Connection Refused - Policy violation  TCP 192.168.1.108:49499->90.24.175.227:57402 on eth1
  Feb 26 18:39:06 2014    ACCESS_RULE TCP 192.168.1.107:49499->111.221.74.31:57402 on eth0
  Feb 26 18:39:13 2014     Connection Refused - Policy violation  TCP 192.168.1.108:49837->89.248.168.42:3129 on eth1
  Feb 26 18:39:13 2014    ACCESS_RULE TCP 192.168.1.107:49837->65.55.223.46:3129 on eth0
  Feb 26 18:39:57 2014     Connection Refused - Policy violation  TCP 192.168.1.108:49584->92.142.109.203:57209 on eth1
  Feb 26 18:42:32 2014     System Log  WAN connection is down
  Feb 26 18:42:33 2014     System Log  WAN connection is up : 5.199.147.151/255.255.240.0 gw 5.199.144.1 on eth1
  Feb 26 18:43:16 2014     System Log  WAN connection is down
  Feb 26 18:43:18 2014     System Log  WAN connection is up : 5.199.147.151/255.255.240.0 gw 5.199.144.1 on eth1
  Feb 26 18:49:53 2014     System Log  WAN connection is down
  Feb 26 18:49:54 2014     System Log  WAN connection is up : 5.199.147.151/255.255.240.0 gw 5.199.144.1 on eth1
  Feb 26 18:50:42 2014     System Log  WAN connection is down
  Feb 26 18:50:44 2014     System Log  WAN connection is up : 5.199.147.151/255.255.240.0 gw 5.199.144.1 on eth1
  

  Hello

  Thanks for your replies!  I looked in the settings and methods to verify this behavior.

  In the end, I decided that the behaviour of "drop the WAN" is not not to blame the LRT224: it seems really to be created by the ISP (the fiber modem): when I plug a small switch between the router and the modem 'abandonment WAN' messages have disappeared.  Now I 'just' convince my ISP to do something...

• Is there a method of direct printing for the chiseled section?

  Original title: Snipping Tool

  I love this tool and use it quite often.  Have I missed something but, for when I want a copy of the capture, I go to Word and paste the snip in a new document, where it can be printed?  Is there a method of direct printing for the chiseled section?  Otherwise, would be MS please consider including it?  Are there other supported this idea, if any?

  Pelcaro

  Hello

  Correct the Snipping Tool doesn't have a print option.

  Use these resources to provide feedback:

  Microsoft Connect
  https://connect.Microsoft.com/

  Provide feedback to Microsoft
  http://www.Microsoft.com/mscorp/Execmail/feedback.mspx

  I hope this helps.
  --------------------------------------------------------------------------------------------
  Rob Brown - Microsoft MVP<- profile="" -="" windows="" experience :="" bicycle="" -="" mark="" twain="" said="" it="">

• Connection to the Wan to LAN RV320 1 individual

  Hello

  I have a cisco RV320, I use 2 wan with different ISP connections.

  It is possible to come out with an ISP to one of the 4 LAN ports?

  I need a specific LAN port for internet connection comes from a specific or 2 wan1 wan, and other lan ports to use load balancing feature.

  Is it possible?

  Thank you

  Hello

  Thank you for the information.

  After reviewing the chart, it seems that what you need is to create links of Protocol 2, on Router 2 and the other on the first router so that traffic can be directed out of the ISP on the right.

  Unfortunately, this is not supported as the routers were not intended to work like this, so there is no way to guarantee that traffic on the second router will come out of the ISP on the right on the first but you can try.

  Please let me know if it worked.

• blocking direct access to the oracle server

  Dear Sir

  One of our condition of pci - dss to stop direct access to the db. One solution I know:

  TCP.validnode_checking = YES

  TCP.invited_nodes = (192.168.1.91, visionhost.solutionbeacon.com)

  But this option will allow the IP address of the node invited with sqlplus using tns names also. Have any have experience to solve the problem of ending up with pci - dss?

  In which paragraph of the PCI - DSS doc that makes you think that there is a problem? I work with version 3.0 (November 2013) and I can't find anything like that. For example, paragraph 8.7 c, "review of database access control settings and application of database to verify configuration settings that the user access directly to the or queries of databases are limited to database administrators" does not say that the DBA is not able to connect to the application server. And all the stuff of firewall in requirement 1 close the access to the network and between networks, not within the network.

  Are you sure that you have a problem? There is no interest to 'fix' something that doesn't have a reference in the doc.

• I tried to edit a pdf file and it keep direct me to the purchase of subscription and I already have one

  I tried to edit a pdf file and it keep direct me to the purchase of subscription and I already have one

  Hi anthonyt40697810,

  Are you able to connect?

  If Yes, then just Sign In to activate the subscription by using your Adobe ID.

  Kind regards

  Nicos

• vSwitch ESXi 5.1 workaround to virtual machines (direct access to the network)

  Hello world!

  I have a server running properly the 5.1 ESXi hypervisor and got inside the physical grid active router with DHCP. How can I configure the vSwitch on ESXi 5.1 work not managed on the network, without VLAN and have direct access to the network?

  Just to clarify, I would like to first of all virtual machines VMware Workstation works - if it is possible to run several virtual machines and define all NICS (Network Interface Card) as connected by a bridge, that is to say. Each VM gets the specific configurations of IP to the external router.

  Since now, thank you very much for the help!

  Best regards

  Eduardo

  With ESXi the vSwitches work comparable to Bridged networking, so there is really nothing special to do.

  André

• Simulate the wind around a player

  I have a video of me on my green screen, and I am trying to simulate the wind around me, like a fall to the cheese. I want it to look like this: Dear Ryan - stop videos post! - YouTube is a way to do it with any third party plugins?

  I think there's some involved roto and directional blur and or a radial blur together to zoom. Something like that might work. Just a blue background United added so you can see the blur. Here is a sample project using a frame of their video... Dropbox - windEffect.zip

  

  Note that the top layer is the actor without any blur, blur is behind. In a typical production environment I create the key and then return a DI (digital intermediate with an alpha using a lossless codec) and the DI allows you to create composite.

• View 4.5 connect the session ends on the WAN access

  I saw 4.5 upwards and running, although I ran into a problem with connectivity from outside the network.

  I the installation of server Connection View and forwarded ports 80 and 443 to view connect server inside - it's a temporary facility until we run all over SSL VPN.

  I can reach the server, download the client, connect, but when he tries to establish the session on the desktop, it disconnects.  Newspapers the for the user login and logoff, as a the packet capture poster that my outside client ends the SSL connection after trying to connect.  This behavior is the same with the RDP PCoIP protocols.

  My question is: view you must install a server security for external connections, am I missing a port for PCoIP / RDP, or something in the roads is bad?

  I guess it depends on how if you use direct connect to this broker for connections.  If you use directly connect you must put at the disposal of the 3389 of VDI machines to the customer outside. If you are tunneling by this broker for connections, then it should work except PCOIP.   If I'm not mistaken PCOIP uses the direct connect method constantly.

  If you have found this device or any other useful post please consider the use of buttons useful/correct to award points

  Twitter: http://twitter.com/mittim12

• should my time capsule be connected with a cable for backups, after the initial installation?

  should my time capsule be connected with a cable for backups, after the initial installation?

  If you mean that you have to keep your Mac connected to a Time Capsule via Ethernet for future backups, then the answer is no. Time Machine and time Capsule are designed to work over wireless for your Mac would just need to be connected to the wireless network provided by the time Capsule.

• Whenever I start Firefox it directed me to the unknown link-

  Whenever I started Firefox, it directed me to the link -http://istart.webssearches.com/?type=sc & ts = 1420034636 & from = kmp & uid = SAMSUNGXSV4084H_0348J1FR518681 - I don't know why I have already done some actions to remove it->
  
  1 Uninstall using process given in the site link-http://istart.webssearches.com/uninstall/firefox.html.
  2 done restart Firefox multiple times with restart windows.
  3 made refreshing Firefox several times but after I updated this new return of my sync account recorded in the post-* @gmail.com.
  4 removal of the Plugins and modules.
  5. make do, tips, and tricks given in page Firefox tutorials and help.
  All this aid... What's not to synchronize my Firefox but this sync account is quite old and stored several add-ons and my personal stuff, so I can't access it without be sync.
  Please quick help, this site is really annoying, any help would be very useful...
  

  ADMIN EDIT: Please do not post your address private in the forums, thank you email!

  If the home page button works fine, but your shortcut on the desktop to send you to the wrong page, the shortcut can be hacked.

  Right click on the shortcut icon > properties > Shortcut tab

  For Windows XP (default location), the goal should be either not less that what follows. If there are extra things, empty:

  "C:\Program Files\Mozilla Firefox\firefox.exe"

  If that checks well, hmm, I wonder if you could have a hidden extension? Extensions are unable to hide mode without failure of Firefox.

  You can restart Firefox in Mode safe mode using either:

  • button "3-bar" menu > "?" button > restart with disabled modules
  • Help menu > restart with disabled modules

  Not all add-ons are disabled: Flash and other plugins still works

  After stops in Firefox, a small dialog box should appear. Click on 'Start mode safe' (not reset).

  Any difference? Also, you can visit the page modules. Either:

  • CTRL + SHIFT + a
  • "3-bar" menu button (or tools) > Add-ons

  In the left column, click Extensions. Then see if something new appears at the time where you posted from your list:

  • 160by2 1.2 ([email protected])
  • Avast security 10.0.2502.149 online ([email protected])
  • dM tab-Counter 0.4 (jid1-eifaPAhtO6PT4Q@jetpack)
  • Forecasts more 0.1.2 (jid1-w3xH9kJhd3KJUp@jetpack)
  • IDM CC 7.3.91 ([email protected])