LW46OUA #ABA: hard drive error. (EFO) Help

Similar Questions

• Satellite L350 - persistent master hard drive errors

  I've known persistent main hard disk errors. Errors, in their first incarnation, were windows freeze at loading screens and screensavers, and then developed by stopping Windows to boot at all. It certainly would not start normally and sometimes would not start in safe mode. I used the recovery partition to restore the computer to its factory settings. A day or two later, the same symptoms began to manifest again, although not as severely. The hard drive errors, freeze on screens and loading screen savers.

  My question is: if I re - format the hard drive master, thus destroying the recovery partition, I could then just restore windows from a newly formed recovery CD? And, in addition, what is the probability that reformatting the drive hard completely would have an effect on the frequency of errors?
  If the hard drive is simply borked, format or not? And if yes, what is the next step?
  Could I restore windows on my drive hard slave and give up on the master?

  Thanks in advance.
  Mike

  Hey Buddy,

  Are you sure that all these problems related to the HARD drive at 100%? How did you check that?

  I don t mean it s not the HARD drive, theoretically, you could be right but before you think to change the HARD drive please use a diagnostic tool special for HDD as Drive Fitness Test:
  http://www.HitachiGST.com/support/downloads/#DFT

  This tool can check your HARD drive for bad sectors.

  If the HARD features of bad sectors disk, formatting will not help you because the sectors are physically damaged. With other words, the only chance is to exchange it.

  But if you have already used the recovery feature of HARD Toshiba drive to reinstall Windows you can say s that no problem of software and it must be hardware related. ;)

• Laptop HP 2000: hard drive error

  Hello
  I have upgraded to Windows 10 one a few days ago and then yesterday when I went to turn on my computer it says this.

  Hard drive error
  Please run the hard drive Test in the diagnostic system
  Hard disk 3 (3F1)

  I ran the test drive and that's what he said

  Smart check: PAST
  DST short: FAILURE

  Help, please!

  You will need to replace the hard drive. Update to Windows 10 had nothing to do with it. After the back if you want to help find a car and its installation and reinstallation of Windows. If your Windows 10 appeared as it is activated, you can do a clean reinstall of Windows 10.

• hard drive error message 1

  Whenever I turn on my laptop, a message appears that there is a problem with my hard drive.  I have prees F2 to get the Diagnostics utility and run the hard drive test. When I do I get this message

  hard drive error

  Failure ID: 90 c 633-6am70r-mfgk0k - 60 c 203

  Product ID: c2n26ua #aba

  Hello

  Error code 24 characters will be a Smart failure or disk Self Test - in both cases, this would indicate that hard is defective and must be replaced.

  If your laptop is still under warranty, contact HP and arrange for the disk replaced - you can check the status of your warranty here.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  If you are out of warranty and would like a guide to replacing the hard drive yourself, let me know.

  Kind regards

  DP - K

• Hard drive error, does not start.

  Computer does not start. I get this failure code:
  Rw1xtw-7ax87b-mfpv6k-619403
  
  Can't find any information on this subject, can someone shed some light on this subject for me?

  Hello

  It decodes for hard drive error 305 or the hard drive has failed, you will need to get the replaced hard drive and reinstall the OS and have a Fresh start, note that all your data is saved on the hard drive will be lost.

• Windows XP does not start, no hard drive error

  I have windows XP installed on my hard drive of 160 GB WD Scorpio Blue PATA on a DELL Latitude D600. One day, I wake up and my laptop does not start. My computer starts up, leaves POST, but the hard drive does not start. He's right there. I try pressing the buttons but it starts a sound signal, so I have to turn it off. Normally, if there is no device that my computer can boot from it displays something along the lines, "no main boot device found. Press F1 to retry boot or F2 to enter the configuration utility. "but the screen does not show anything.
  I ran chkdisk and a number of other diagnostic tools on the hard drive, but nothing helped. I have Ubuntu on a USB key and with him, I can access the files on the hard drive - all files are intact, and I can read/write without problems. It just does not start.
  How would I go about fixing this? Any help is appreciated. It is the third hard drive that has failed inside my D600 (my second WD). I've had enough of this!

  Try to use the last good known Configuration:

  http://support.Microsoft.com/kb/307852

  and see if that clears things up to the top.

  Hope this helps

  Post back if necessary

  ____________________

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Start up and boot problem. Hard drive error. HP pavilion laptop Home Premium. Windows Vista preinstalled. No cd came with it.

  Nothing new added to comp. Got the hard drive error message and followed the instructions to fix/repair. All translations tried (almost every test suggested/memory/hard drive, etc.) could find NO problem with the memory or hard drive.  Once I have pass the problem to boot/start the computer works fine!   Crazy!  Any sugg. would be appreciated.

  Hello

  ·        Since when are you facing this problem?

  ·        What are the fix and repair that you tried to solve this problem?

  ·        Outside this disk verification error, do you get any other error message?

  Method 1:

  I suggest you to do a scan of the SFC. File system (CFS) Auditor verifies that all Windows 7 system files are where they should be as they are by default and not corrupted, changed or damaged.

  ·        Click Start, click principally made programs, accessories, right-click on command prompt and select run as administrator.

  ·        Click on continue or provide administrator credentials if prompted.

  ·        In the command prompt window, type the following text, and then press ENTER:

  ·        sfc/scannow

  ·        You should see the following message on the screen:

  § Begin the analysis of the system. This process will take time.

  § Beginning verification phase of system scan.

  ·        % Of verification complete.

  ·        Once the scan is complete, a test to see if the problem you are experiencing is resolved or not.

  For more information, see the article mentioned below.

  http://support.Microsoft.com/kb/929833

   

  Method 2:

  I suggest you to set Chkdsk to run when the system restarts the next time. Follow the steps mentioned below to set Chkdsk to run when Windows Vista reboots the next time.

  a. click on start, then run.

  b. in open, type cmd, and then press ENTER.

  c. use one of the following procedures:

  Procedure 1: To run Chkdsk in read-only, at the command prompt, type chkdsk, and then press ENTER.

  Procedure 2: To repair errors without scanning the volume for bad sectors, at the command prompt, type chkdsk volume: / f, and then press ENTER.

  Procedure 1: To run Chkdsk in read-only, at the command prompt, type chkdsk, and then press ENTER.

  Note: If one or more files on the hard disk are open, you will receive the following message is displayed:

  a. Chkdsk cannot run because the volume is in use by another process. You want to schedule this volume to check the next time the system restarts? (Y/N)

  b. Type O, and then press ENTER to schedule the disk check, and then restart your computer to start the disk check.

  Procedure 2: To repair errors, locate bad sectors and recover readable information, at the command prompt, type chkdsk volume: / r, and then press ENTER.

  Note: If one or more files on the hard disk are open, you will receive the following message is displayed:

  a. Chkdsk cannot run because the volume is in use by another process. You want to schedule this volume to check the next time the system restarts? (Y/N)

  b. Type O, and then press ENTER to schedule the disk check, and then restart your computer to start the disk check.

  You can see the article mentioned below for assistance.

  Check your hard drive for errors

  http://Windows.Microsoft.com/en-us/Windows-Vista/check-your-hard-disk-for-errors

  Method 3:

  I suggest you to do a system restore. Follow the steps mentioned in the article below.

  What is system restore?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-system-restore

  System Restore: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit ourMicrosoft answers feedback Forum and let us know what you think.

• Hard drive error, but passes diagnostic

  I have a vostro 320 all in one computer. Yesterday he left initializing with a hard drive error, but when I run the hardware diagnostics all past. When I go into the installer the Bious does not see the hard drive. Current Bious is 1.2.0 and current is 1.4.0.

  If the BIOS does not see the hard drive, no - you will need to replace the disk.

  You can take a chance on the resettlement of the player (unplug the system and disconnect and reconnect the hard drive), but if so, it is not detected by the system, it is toast and needs to be replaced.

• I recently installed a new disk of hard on my laptop, is there a way I can still use my OS to a new hard drive? pls help

  I recently installed a new hard drive on my laptop, and Ive had an activation problem my windows 7 OS, it says that I cannot activate my OS on this machine, is it possible that I can still use my OS to a new hard drive? pls help

  You must activate by phone and speak to a representative of activation.

  How to activate Windows 7 manually (activate by phone)

  1) click Start and in the search for box type: slui.exe 4

  (2) press the ENTER"" key.

  (3) select your "country" in the list.

  (4) choose the option "activate phone".

  5) stay on the phone (do not meet all the automatic guests) and wait for a person to help you with the activation.

  (6) explain your problem clearly to the support person.

• Dell Hard Drive Diagnostics fix hard drive errors

  My computer would stop working and say that I had a software problem.

  When restarting it would run for about 15 minutes and the cessation of work and

  show the same error.

  I have run the Dell diagnostic program and it showed that I have several

  Hard drive errors.

  After the diagnosis my computer now works fine.

  The diagnostic programs to correct the mistakes of hard dirve when he finds them.

  My computer is a Dimension 4700 running windows XP Professional

  Service Pack 3

  
  

• Hard drive error (HP ENVY 17 Notebook PC, PN: A9P79UA #ABA)

  at startup, I get the Message disk error hard and please run the hard drive test in the System Diagnostics

  Hard drive 1 (3F1)

  F2 System Diagnostics

  For more information, please visit: www.hp.com \go\techcenter\startup

  I ran boot test, 100% of the system memory is ok, but it took a lot of time

  I ran disk hard test then I get this message

  "Main hard drive Self Test

  Quick test

  Red, I get (HDD 1 fault)

  Hard drive Self Test

  Full test

  Red, I get (HDD 1 fault)

  INTELLIGENT testing of output control

  "color yellow, I get (SMART hard drive SPENT).

  Please how can I solve this urgent problem. Moreover, how much disk hard comes with the hp envy 17 notebook pc?

  HP ENVY 17 Notebook PC, PN: A9P79UA #ABA {deleted private information}

  Here are the specifications of your laptop of HP ENVY 17-3077NR. You receive the error code indicates that your computer's hard drive has failed or is about to fail. To resolve this issue, you must replace the hard drive with a new one that is similar to the original hard drive. It is clear this form, this model uses a single 750GB 2.5 "SATA hard drive.

  Once you replace the hard drive, you will need to use your HP recovery disc set staff to return the computer to a factory State. If you don't create these disks, you may order from HP or third-party provider ComputerSurgeons.com. If the figure 25 Windows product key on your computer is still readable, you can download Windows and install it using the product key on your computer.

  Please click the White Star of KUDOS to show your appreciation

• 2000-2d19WM HP laptop hard drive error

  My HP 2000 is currently saying that a SMART disk check has detected an imminent failure.

  When running hardware diagnostics gave me a failure ID of: 6CX1VS-70P7AE-MFGJWK-60BA03

  My product ID is: E0M17UA #ABA

  I wonder what my options are. My PC is still under warranty and I would have preferred not to lose the data I have on that hard drive.

  Thank you.

  Hi @RSBlack ,

  Thank you for visiting the Forums HP's Support and welcome. I looked into your problem on your laptop HP 2000-2d19WM and the error message.

  Product E0M17UA number
  Status of the warranty covered under the end of warranty date 2015-01-22 (YYYY-MM-DD)

  Please contact our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click on the link for the number of support in your region. They will be happy to help you immediately.

  Thank you.

• external hard drive error

  Gusy I have my external hard drive from toshiba, it seems that I can copy is no longer the files inside it on another computer or hard drive. its gives me this error ", you can always open or copy the files on the disk, but you cannot save the changes.

  At first it worked fine on my mac I formatted as MS-DOS (fat32) then. I used it for awhile and it was fine, then suddenly it began to appear this error. It tell me to save, but when I try to do, I can't copy it to another somewhre. can someone help me?

  Try to run the help Utility/First on the drive.

• Satellite A200-1AI - Windows has detected the hard drive error

  Hi guys.

  I think its time I replaced my hard drive. Ive done all the checks and his return there is no errors with the hard disk, yet whenever I connect I get a message saying that there is.

  I guess that's only a matter of time before things get more serious.
  Its just now that it unattached restarts automatically.
  Ive gave my laptop below specifications and the specifications of the hard disk drive.
  I do not know which drive hard im supposed to be looking at.

  I don't want to buy one and then duty send because its incompatiable.
  Ive done some reading on the internet and he says I cn buy any production, but I need to know wheather its an IDE or SATA, what are these and what do mean? How can I find out what my current car?

  Also should I look for a hard drive with the same speed? It doesn't matter if its fatser?
  Wise, capacity is also ok for larger, will my laptop be able to handle it. Thanks for help

  MODEL NAME: Toshiba Satellite A200-1AI
  MODEL NO.: PSAECE-00U00JEN

  HDD SPEC:

  TOSHIBA MK2035GSS HARD DRIVE
  CAPACITY: 200 GB
  CERTIFICATION: S.M.A.R.T
  DrRIVE ROTATION: 4200 RPM

  Hello

  The Satellite A200 supports the SATA HDD controller.
  That's why you need to buy a SATA 2.5 HARD.
  The value of the rmp is not really important for compatibility issues with the 4200 RPM HDD or more is possible and compatible.

  SATA controller not limited to any size of HARD drive, you can also use large drives.

• Hard drive error

  Last Friday, when I got a message on my computer. I started my computer and waited for my coming screen lock. But it does not.
  
  To place a display that showed a message (HDD error please run the System Diagnostics hard drive test.) Hard drive 1 (3F1) f2 System Diagnostics. For more information, please visit: www.hp.com/go/techcenter/startup ).
  
  Yes, I ran the test. In fact, I ran two of them. After checking the hard drive, but the test of memory appear Smart check & short DST not installed.
  
  Anyway, when I press exit after the exam he brings me to the SAME screen (HDD error) I went to insects to ask for help and they said I need to contact me Hp.Please help.
  
  My product is a HP Pavilion x 360
  
  And I got it in June 13,2014

  If the computer is less than a year old HP probably fix it at their cost. If you live in the United States, call the 1-800-HP-INVENT and go to the personal computer support to make a claim. Probably they will send a box for it and have shipped to and returned from a repair center.