M1000e configuration

Similar Questions

• Config port / VLAN on switch MXL

  I'm not a network engineer, but I try to set a port to my MXL switch to a VLAN that will route traffic on virtual machines on a local network of calculation.

  This is the port Te 0/52 on the back of the MXL and I am running ESXi on servers in my m1000e.  In fact, I have two MXLs in the tissue A of the m1000e configured with VLT via the interfaces of the FourtyGig.  This part has been implemented by people of Dell Tech Services, making the installation.

  Here's what looked like the config to start:

  dsa1 #show vlan

  Codes: *-Default VLAN - VLAN, GVRP, R - G remote control Port Mirroring VLAN, P - primary, C - community, I - isolated
  O Openflow
  Q: U - no identified, the T - tag
  x - unidentified Dot1x, X - Dot1x tag
  o - unidentified OpenFlow, O - OpenFlow tag
  G - GVRP tag, M - Vlan-stack, H - VSN tagged
  i unidentified intern, I - labeled internal, untagged, V v - VLT - VLT tag

  Ports Status Description Q NUM
  * 1 U active Po33 (0/33.37 Fo)
  U Po41 (Te 0/41-44)
  Te U 0/1-32
  115 active Mgmt T Po41(Te 0/41-44)
  V Po33 (0/33.37 Fo)
  Te T 0/1-32
  486 active VMGuest T Po41(Te 0/41-44)
  V Po33 (0/33.37 Fo)
  Te T 0/1-32
  Te U 0/49-50

  And I wanted to add VLAN 1000 to calculate, so I did the following:

  dsa1 #conf

  dsa1 (conf) #interface Te 0/52
  dsa1 (conf-if-you-0/52) #show config
  !
  interface TenGigabitEthernet 0/52
  no ip address
  MTU 12000
  hybrid portmode
  switchport
  FlowControl rx tx off
  spanning tree rstp edge port bpduguard stop-on-violation
  no downtime

  dsa1 vlan (conf) #interface 1000
  dsa1 (conf-if-vl-1000) #show config
  !
  interface Vlan 1000
  Description information
  name computer
  no ip address
  Tagged TenGigabitEthernet 0/1-32
  Unmarked TenGigabitEthernet 0/52
  no downtime

  VLAN now looks like:

  dsa1 #show vlan

  Codes: *-Default VLAN - VLAN, GVRP, R - G remote control Port Mirroring VLAN, P - primary, C - community, I - isolated
  O Openflow
  Q: U - no identified, the T - tag
  x - unidentified Dot1x, X - Dot1x tag
  o - unidentified OpenFlow, O - OpenFlow tag
  G - GVRP tag, M - Vlan-stack, H - VSN tagged
  i unidentified intern, I - labeled internal, untagged, V v - VLT - VLT tag

  Ports Status Description Q NUM
  * 1 U active Po33 (0/33.37 Fo)
  U Po41 (Te 0/41-44)
  Te U 0/1-32
  115 active Mgmt T Po41(Te 0/41-44)
  V Po33 (0/33.37 Fo)
  Te T 0/1-32
  486 active VMGuest T Po41(Te 0/41-44)
  V Po33 (0/33.37 Fo)
  Te T 0/1-32
  Te U 0/49-50
  1000 active Compute T Te 0/1-32
  Te U 0/52

  But I wanted to add THAT VLT Po33 tag to the new VLAN because there is in others, not because I really understand what it does.  In my view, it is used for load balancing?  If I label it with the command 'tag Po33' in the config of vlan, out with the status "T" instead of "V".

  Here are the details of the VLT:

  dsa1 #show vlt detail
  Local LAG Id counterpart LAG Id status Local Peer status Active VLAN
  ------------  -----------  ------------  -----------  -------------
  41 41 UP UP 1, 115, 486
  dsa1 #show brief vlt
  VLT area in brief
  ------------------
  Domain ID: 100
  Role: secondary
  Primary role: 4096
  ICL Link Status: to the top
  Status of heart rate: upward
  VLT Peer status: to the top
  The local unit ID: 0
  Version: 6 (4)
  Local system MAC address: f8:b1:56:09:70:b1
  MAC address of the remote system: f8:b1:56:09:70:fd
  Configured the system MAC address: 00:01:00:01:00:01
  Version of the remote system: 6 (4)
  Restore delay timer: 90 seconds
  Delay-restore Abort threshold: 60 seconds
  Routing peer: disabled
  By the peer-routing-Timeout timer: 0 seconds
  Multicast peer-routing timeout: 150 seconds

  So my questions are, I'm on the right track?  It will do what I want it to do is send traffic on port 0/52 Te which is labeled in ESXi with 1000 VLAN?  Should I worry the VLT marking stuff and if yes, how should I do the VLT marking rather than normal marking?

  The connection only 1 port of MXL 1 to a device, this device is considered a switch/host an orphan. A VLT connection will have 1 port each MXL placed in a port channel and connected to a device.

  Here is a good article that covers the VLT in use with different Topologies.

  http://Dell.to/1wfDl3n

  And the User Guide is a good source to have as well.

  http://Dell.to/1Hy70bb

• Reference Dell M1000e + aggregator MI/O port mapping

  Hi all

  I intend to install a new chassis Dell M1000e with Dell M/o aggregator. During the time of solution, I have a few questions about correspondences between the physical uplink with NDC blade ports ports. A Please check the config below and specify my queries?

  My hardware:

  • 1 x Dell M1000e
  • 2 x M i/o aggregator (A1 & A2)
  • 16 x M630 Blade (Qlogic 57840 S ANC four ports card)

  Reference DELL M/o aggregator:

  (reserved for Future use) module QSFP + 2 ports (Port No1:33 - 36 & No2:37 Port-40)

  I want to use these two modules for my blades 4-port Quad and the confusion I had, how to associate these 16 ports (8 ports of each module) to the server blade and the amount of bandwidth I will get by blade with redundancy.

  Module 4-port SFP + 10 GbE (Flexi-O of the Bay) (Port No.: 41-48)

  Module 4-port 2/4/8 Gb FC FlexIO (Flexi Bay 1) (Port No.: 49-56)

  FYI - I would like to install ESXi 6.0 on all blades

  Thank you!!

  Vinay

  Oriented server ports are configured automatically as part of the aggregation of links groups if the server is configured for the LACP Protocol. Static GAL is not supported.

  You will use the segregation network VLAN. A VLAN for network traffic and the other for the CF. Here are the commands to configure interfaces for different VLANS.

  Unidentified:

  Dell (conf) # tengigabit interface 0/16

  Dell(conf-if-te-0/16) # vlan unidentified 4

  Output Dell(conf-if-te-0/16) #.

  Tag:

  Dell (conf) # tengigabit interface 0/16

  The tag vlan Dell(conf-if-te-0/16) # 4

  Output Dell(conf-if-te-0/16) #.

  Traffic from servers will follow the path of the VLAN. For example, if an internal server, facing the port is set to VLAN 4, that traffic will be transmitted on the uplink port which has also set to VLAN 4.

  By default, all external ports are placed in a single whole LAG. However, you can change the configuration to support several shifts of uplink. Page 159 of guys configuration takes you step by step on setting up several shifts of uplink.

  The aggregator automatically configures to match the FCoE parameters used in the switches to which it connects through its uplink ports. FIP snooping is automatically configured on an aggregator. Automatically configured port channel (LAG 128) works CWF port mode. See page 86 for more information and examples of config.

  For redundancy, you could stack the units together. 241 page details the process of stacking.

  Page 54 of 102 of the Guide blade IO has one other diagram that details more internal server port mapping for each blade.

• Rename the name of Module e/s in M1000e

  Hi friends, is it possible to rename the name of Module e/s in M1000e? For example, in SLOT A1 in the name field displays the switch model and I would like to configure to display the name of switch´s.

  Concerning

  Hello

  There is not a way to rename the switches, only the server slots.

• Networking M1000e

  We ordered a M1000e chassis. We use Dell Force10 MXL blade switches (2) for networking. My question is that the switch MXL comes with 2 ports QSPF +. We also ordered (1) of these (Module 10GbE SFP +, 4 ports, Hot Swappable, 4 x SFP + ports (optical or direct attach cables needed) (331-8187)). WE have 1 but we want redundancy. My question is can I use a cable QSFP + who has a connection to 40 GB on the end of switch MXL and use 1 or 2 of the 10 GB SFP + cables on the other end in my Cisco switch? WE have not enough ports 10 Gbit/s at the moment to use all 4. I don't know if we need to use all 4 cables of 10 Gbps or can use 1 or 2 and develop in all 4? We think just go back the 331-8187 and using the drop cable.

  Using an extension cable for the connection of the switch will work fine. With cable bypass, you are not required to run all the lines on the same unit, or use them all at the same time. Each of the four 10 GB cables will act as a single port.

  Page 406 of the configuration guide details how to divide the QSFP port in ports SFP +.

  http://Dell.to/1IIq8r2

• M1000e with M8024 (problem connecting to pass)

  I have a Dell Poweredge M1000E Blade chassis with two switches of the M8024.

  I configured the IP addresses of the M8024 (B1 and B2) on the CMC web.

  All ports on the controllers of chassis are connected to my network.

  I can connect without problems to the M8024 into the slot in B2, but cannot connect / ping / access the M8024 in B1.  I have tried power cycling/replace the switch but no luck.

  Any suggestions?  I tried not to do anything via a SERIAL connection.

  I understand the problem!

  CMC M1000e chassis preview / network / config VLAN.  The VLAN Tag parameter has been activated for the M8024 in B1.  This prevented work properly on our network, because the vlan defined for the specified VLAN ID was not set up.  I unchecked the box in the column "Enable" (for B1) and he now available!

  Thank you!

• M1000e send much alarm power supply

  Since the update of the firmware of MCC to 5.12 my M1000e sends this alarm several times per hour:

  Power supply 3 functioning normally

  I spent PSU-3 with POWER-4 block already, no change. All 6 power supplies are fine, 1 and 2 are online, 4 to 6 are on standby and 3 is go to sleep and online. How to configure to send only real alarms?

  E5-2660

  What you see is due to enabling a dynamic commitment PSU on the M1000e, the PSU will engage and disengage to meet the power requirements by the chassis. The commitment of feeding generates messages that you see. There is nothing to be worried about, it works as expected. Now because it looks like you have it set up for alerts, you will continue to see them coming, but there is a update down the road that will allow you to control the PSU Audit alerts / information to stop notifications.

  Let me know if this helps to clarify the situation.

• Chassis & 10GbE blade M1000e through Modules

  We rotated M620 blades with 1 GB Pass Through modules without any problem. The M620s have the Qlogic\Broadcom cards mezzanines KR 10 GB for slots chassis A1\A2.

  We have just bought a few Pass through modules of KR 10GbE and exchanged out them. in the same locations of A1\A2. When the configuration of the BIOS, we get green link is turned on with our Cisco Nexus switch which shows a connection on the port, but when ESXi6 is loaded there is no link (orange light just on the module). NIC in ESX is set to automatic (will not force the 10 GB according to VMWare).

  Tested updates, driver updates, change cables Twinax Dell SFP + and fiber but no link. If I put the 1GbE modules back in they work fine.

  Strangely, at one point I did get network link in ESX running a single passthrough but have not been able to recreate it. Am I missing something that I do not see a reason for this which is why they should not work? This chassis we test on is quite old (2008) and we use just to test before deploy us in our new M1000e chassis. What is the material inside the frame at the origin of a problem that has subsequently been updated?

  You should be fair exchange in the chassis with the median plan 1.1.

• M1000e chassis, CMC, M6220 OOB, IDRAC and network management

  Hello

  I'm currently trying to isolate all elements of management on our network to a VLAN dedicated.

  For the moment, I'm a bit confused by how the OOB of the M6220 in my M1000e chassis communicates with the rest of the network.

  It would be correct to say that the MCC is the interface used for all blade IDRAC communications as well as the M6220 OOB?

  Since the OOB cannot be marked a VLAN would not enough to affect my management VLAN IPs to all above mentioned interfaces and then just by linking the CMC to a port of LAN VIRTUAL marked on one of my main past?

  I hope someone can enlighten me here.

  Thank you.

  Yes. You are right. All Modules IO (M6220) and the iDRAC management interface is through CMC. You can set the VLAN for all Modules IO and the iDRAC. To configure VLAN for the CMC and other modules in the chassis, connect you to web interface CMC and cross 'Chassis overview-> network-> VLAN.

• Configuration profile to apply a blade to other blades

  Hello

  Can someone tell me pls to a how-to on a blade Configuration capture profile and apply that to the other blades in a m1000e chassis?

  Is the material must be exactly the same (the same model and size of hard drives, as SSD vs non - ssd? What happens if the disks are different)?

  Also, applying a profile will inform as this automatically causes a reboot?

  THX,

  John Bradshaw

  Bradje1,

  If you follow this link, it will guide you through to replicate the configuration between the blades. Which, when applied, causes a reboot. The blades will also have to match the level you are replicating, for stability I also recommends that the revisions to the BIOS, controller of life cycle, as well as the iDrac are updated and current as well.

  I do not think that the readers and table will be a problem

• Tips to add a VPN router to my current network configuration

  Dear all

  My apologies if the answer to this question already exists, however, I searched in many situations and none seem to match what I'm after.

  I currently have an ISP modem/router in Bridge mode connected to a TC of Apple which is my wireless router, I have 2 Express airport connected to this acting as the extensors of the range.  I have a VPN service through the MyPrivate network I activate on the desired device when required and everything works fine.

  What I want to do now is to be able to use my AppleTV and burning Amazon via the VPN as well so you need to add a VPN router in the configuration.  I want to finish with 2 wireless networks running together for these devices who need VPN and those who are not.  I don't want to lose the opportunity to extend the network to express it however airport.

  If someone could explain to me if this is possible and if so how do I set up the network.

  Thanks in advance

  Mark

  Basically you would need a device that supports VPN-passthrough and VLANS for your goals of networking. MyPrivate network, seems to be a VPN SSL, which is a user-server configuration. In other words, you install a client VPN on your Mac and you connect to the VPN network MyPrivate server to establish a VPN tunnel.

  Networking two or more "separated", should be using a router that supports VLAN services. Each segment of VIRTUAL local area network, in essence, would be a separate, she either wired or wireless network or a combination of both. This would probably be the 'easiest' part for the installation program.

  Now how combining the two would be the question, and I don't know what would be the best way, or even if it is possible.

  A few thoughts:

  • Use a router that supports VLANS. Create at least two VIRTUAL LAN segments. One for Apple TV & Burns, one for Internet access in general. Connect the device to VPN client host on the first segment, and configure for Internet sharing.
  • Download a dedicated VPN network application that supports hosting of third-party VPN clients, like yours. You would still need a router that supports VLAN to provided separate network segments.
  • Hire a consultant network. Let them know what you the goals of networking and ask them to offer potential solutions.

• Configure my email on Thunderbird

  Hello world

  I use a PC for business purposes (I know it's bad) and I would like to set up my email address in a Thunderbird client. I tried to use my email address in @ mac.com, me.com and icloud.com with iCloud vainly password authentication each combination.

  This means that there is a password different email than the one iCloud and if yes, where can I find it?

  Thank you for your support.

  Lionel

  Here are some links that should help you-

  Configure iCloud Mail in Thunderbird

  Download Thunderbird to work with Apple mail

  Cannot get iCloud email must be recognized in Thunderbird

  iCloud: server for e-mail clients - Apple support settings

  ICloud mail in Thunderbird configuration

• Old lock to activate ipad asking for Apple ID and password used to configure icloud, which is forgotten. Help?

  My older ipad bouchoirs activation requires Apple ID and password used to configure icloud. I think I know the ID because she tips ***@outlook.com, but not the old password. Help?

  Try https://iforgot.apple.com

  or

  Contact Apple for the Apple ID account security support

  https://support.Apple.com/en-us/HT204169

• Can automatic unlocking be configured on more than one Mac?

  I can set up this feature on my iMac, but not my MacBook Pro? Can only be used with one machine at a time?

  Hello

  Apple Watch can be used to unlock several Macs using Auto unlock, subject to each Mac meeting the requirements of the system and is configured accordingly.

  Automatically unlock your Mac with your Apple Watch

• Cannot configure the Pop of Hotmail on Mail account under macOS Sierra

  Hello.

  I'm on a MacBook Air - end of 2014 with macOS Sierra installed.

  I decided to perform a new installation of the latest version of Mac OS. As I did this, of course, I've erased completely any configuration, I had: this has the Mail app.

  I want to create access to two accounts different Hotmail via Mail App. Apple unfortunately, it's automatically my IMAP accounts - something I really don't like / want - and I want to create POP accounts!

  I check online on how to do it (because Yosemite, holding the Option key during the initial installation, no longer works.) I write a bad e-Mail and after trying to access it, I get an error message and automatically mail gives me the possibility to choose between an account IMAP or pop. Also, it requires me to give the outgoing server and receiving code «»

  MY QUESTION IS: What are the current codes for Hotmail? Because I searched online and after typing the (I assume) good, Mail tells me that it does not recognize my email address and/or password. (Be aware that during the execution of this, I also write my e-Mail address correctly!).

  I really need my accounts connected to Apple Mail, BUT I really need to make sure that it doesn't copy emails and not delete them from the server!

  Thanks in advance for any information you can give me.

  Ask Microsoft about the configuration necessary to initialize one of their products to access pop.