M3 C220 problem (Cycle start "config... Screen)

Similar Questions

• Go off & on several times before the monitor turns on. Comp seems to start OK but the problem is with the screen.

  Original title: XP start help please...

  ... are to be turned off & on several times before monitor lights. Comp seems to start OK but the problem is with the screen. Do I have to make a boot disk & if so - HOW?

  Hello

  ·         What is the brand and model of the computer?

  ·         You get the error message?

  ·         Did you check the connection of the cable to the monitor?

  ·         Have you tried to update to the latest graphics card and motherboard chipset drivers?

  First, try to connect your monitor to a well known PC, maybe the old laptop that you use now. If the monitor works, the problem is with the video card in your PC. If the monitor does not light, the monitor. It is usually cheaper to buy a new monitor that in order to be an old repaired, unless the monitor is still under warranty.

  Try connecting a monitor well known to your PC. If the monitor works, your old monitor is fried and needs to be replaced.

  If your monitor works when connected to another PC, the problem could be your video card. First, and then you turn on your PC, the power and cooling case fans run they. If they do not, it could be the power supply.

  Then, open the computer case. Before you do anything inside, unplug the power supply.

  IMPORTANT! Touch any metal part of the computer case to connect to the PC. A single static spark can destroy computer circuits.

  If the video card is the type of card that plugs into a slot on the motherboard, remove the screws or attached at the top of the card, remove the card, to manipulate the card by the edges to avoid disturbing the circuits on the card, carefully and re - install the card. Sometimes simply reinstalling the card corrects the problem.

  If this does not work, replace the video card with a card of similar type. Perhaps now is the right time for an update of video card.

  If the video card is integrated into the motherboard, you can install a new card in one of the PCI slots on the motherboard. When the PC starts for the first time, go into the bios and disable the onboard video.

  Resources for troubleshooting problems in Windows XP

  http://support.Microsoft.com/kb/307960

• Failed to start; dark screen extended

  On the attempt to start, the screen was black. Screen brightness then returned; It appeared that I was in 'safe mode' and that, perhaps, I forgot my password. I then initiated a reboot, but the same cycle repeated, starting with a black screen. Help. MacBook Pro OS X El Capitan.

  Reset the NVRAM/PRAM memory.  http://support.Apple.com/kb/PH18761

  Reset the SMC. Choose the method for "on Mac Laptops with non-removable battery.

  https://support.Apple.com/en-us/HT201295

  If this does not help, please contact Apple.

  Click 'Contact Support' at the top right of this page.

• 12 Firefox guard start full screen mode.

  Since upgrading to Firefox 12, he wants to start full screen mode. I don't want to say extreme full screen mode where even the menu bar is hidden. I mean the most "typical" full screen mode where it just gets as large as possible, but has the same content. I tried to force a new profile (in renaming ~/.mozilla/firefox) and that fixed it. But then, as soon as I got the personal bar is released, it was again full-screen mode. I wish that there was something in the preferences for this. I NEVER want it to start full screen mode. It is Ubuntu 11.10.

  Last night I upgraded to Ubuntu 12.04 (aka specific Pangolin), and the problem disappeared. No more car don't maximize at startup.

• Mail is stuck in a loop, force quit/restart it closes, and then when I opened the Mail once again, the cycle starts over.

  I am El Capitan OS X 10.11.3, Mail is stuck in a loop, I was responding to a message, and I tried to send it. Now, he presents this message, and then switch to another message / desktop /, mail inbox home screen, then the loops again.   Force quit and restart it closes, then when I open the Mail once again, the cycle starts over.

  I can't use the mail app at all.

  Open the menu go with down option - Open Library - containers and move the folder "com.apple.mail" on the desktop.

  Restart your Mac and check if it works very well.

• After that start monitor/screen becomes black with visible vertical lines

  After that start monitor/screen becomes black with visible vertical lines. Move the mouse shows an activity going on behind the disorder. My son says video card?

  Hi Melissa,

  ·         Since when are you facing this problem?

  ·         Have you checked the issue by connecting a different monitor?

  Step 1: It seems to be a hardware issue to me. Check if the cables are well connected.

  Step 2: Connect another monitor to the computer and see if the problem persists.

• Problem event name: Blue Screen, locale ID: 1033

  Hello

  I have a HP Pavilion computer with windows vista home premium. The computer was working well, but for the last ten days, he began to be planted in the middle. When I try to start it, it is not able to boot and start in safe mode. I get the following problem description

  Problem event name: BlueScreen

  OS version: 6.0.6000.2.0.0.768.3

  Locale ID: 1033

  More info

  BCCode: 116

  BCP1: 8A36D008

  BCP2: 8DC9CF40

  Also sometimes when the computer starts in safe mode the screen is split horizontally two equal haves. I tried to restore the system to an earlier date when I have not had the problem and everything seems to work fine for a day or two, but again, the problem has started to come. Can someone help me please in the present.

  Thank you very much!

  Bug Check 0 x 116: VIDEO_TDR_ERROR

  This indicates that an attempt to reset display driver and recover a timeout failed.

  Update the drivers of graphics card, updating the BIOS and check the RAM for errors.

  In ADDITION, install the Vista Sp1 and Sp2, you always use Vista RTM!

  André

  "A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/

• Start of Windows to install updates and then fail, restores the installation then the cycle starts again.

  original title: I continue to receive updates for Windows. Updates begin to install fail, updates to day is awarded automatically installation and then the cycle starts again.

  This process takes about an hour, during which I can't use the laptop.

  Hello

  ·         Update is causing the problem?

  ·         You get the error message?

  Method 1:

  Try to install the update to the clean boot and check if it helps.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135/en-us

  Note: Don't forget to start your machine in normal mode by following step 7 of the link.

  Method 2:

  You can try temporarily turning on all security software and then try the updates again.

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  Important note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 3:

   

  Also refer to this article and check if it helps:

   

  Problems with installing updates

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-installing-updates

• 4 keyboard key opens the calculator, 3 button opens Notepad, - key starts the screen saver.

  You have problems with programs: when I hit the 4 key, my calculator will appear.  I checked hotkey in properties, and he says nothing.  When I assigned another shortcut to the calculator, the 4 button was always popping up the calculator.  The 3 button opens notepad and 0 or - starts the screen saver. 7 pop open my cd-rom drive.  5. I can't use at all (I'll have to use the keyboard to the right of my keyboard to type this message again.

  • Recent changes made to your computer: drivers installed MinoHD.  A refurbished device that my virus scan caught and removed the 2 virus when I first plugged it.  In addition, have updated Mozilla firefox a couple of times on consecutive days - I thought randomly.
  • What you have already tried to solve the problem: Virus scans a couple from different sources.

  I can't type the dollar sign (Maj 4) at all.  Although I hold SHIFT, it always opens the calculator when I press 4.  Someone has an idea?

  It's a laptop Lifebook Fujitsu Series N.  After I posted this, I heard somewhere that it could be a combo of my function key or my windows key.  I started playing with these buttons, including hitting the number lock / scroll lock key.  None of this seems to work, but then 5 minutes later, I tried to work on something else and I hit key 4 by habit and it worked normally.

  I do not know what undid the problem, but it was something in the sense of what you're saying.

• Laptop stuck on "Starting Windows" screen

  So, this afternoon, I tried to start my laptop HPG42-373, and it got stuck on "Starting Windows" screen. I ran tests of memory at startup and primary HD, in which startup failed, and primary HD came out with this: "hard disk 1 (303) Quick '. What can I do to solve this problem, if anything, or just to save what I can from my old files?

  Hello

  303 error code is a disk failure short self-test and would indicate that hard is defective and must be replaced.  This is also consistent with the question of commissioning.

  If your laptop is still under warranty, contact HP and arrange for the disk replaced - you can check the status of your warranty here.

  If you live in the United States, contact HP here.

  If you are in another part of the world, begin here.

  If you are out of warranty and would like a guide to replacing the hard drive yourself, let me know.

  ************************************

  Concerning access to the data on this HARD drive, here are some options you can try.

  1. one possible way to try to recover your files from a disk non-boot is to follow the process described in the link below.  The CD of the Ubuntu operating system you create can launched from the CD alone (IE it doesn't have to be installed on the hard drive) and I've often found to successfully extract data even a hard failure.  When you created the CD, follow the instructions and see if you can save your existing files. 

  http://www.howtogeek.com/HOWTO/Windows-Vista/use-Ubuntu-Live-CD-to-backup-files-from-your-dead-Windo...

  2 another option would be to remove the drive HARD, place it in an external enclosure - is an example of the link below - connect to another PC and see if you can access your files.

  External 2.5 HARD drive caddy ".

  Kind regards

  DP - K

• Stuck on "starting windows" screen during installation of Windows 7

  Hello

  I used windows 10 in dell inspiron13 7000 series. Now, I want to use windows 7 as for my personal use. When I try to boot my laptop with USB stick bootable, because I don't have cd player in my laptop. The problem is when I run the startup it stuck at 'starting windows' screen I can't go any further, so I need force shutdown my laptop. I am unable to install windows 7 on my laptop. What can I do, please help me.

  Thank you.

  Hi Praveen,

  Thanks for posting your question on the Microsoft community.

  We need more information about the issue so that we can help you better.

  1. is Windows 10 still installed on your computer or you have wiped the hard drive?
  2. don't you upgrading from Windows 7 to Windows 10?

  Thank you for details on the issue.

  If Windows 10 is installed, you can downgrade to Windows 7 within 30 days of the upgrade. If it crosses the 30 day limit, the option in the settings that allows you to return to your previous version of Windows will not be available.

  Please see this link:
  Return to Windows 7 or Windows 8.1
  http://Windows.Microsoft.com/en-us/Windows-10/going-back-to-Windows-7-or-Windows-81

  However, if you want to install Windows 7 from an external installation media, you can re-create the rack installation of Windows 7 from this link:
  https://www.Microsoft.com/en-us/software-download/Windows7

  It is possible that the installation media does not develop properly. Please also make sure that you disconnect all the devices connected to the computer before installing Windows 7.

  Note: You may lose programs installed after upgrading Windows 10. I strongly recommend to back up your personal files and data on an external hard drive.

  I hope this information helps.

  Simply answer the required information and let us know if you need more help.

  Thank you

• Try to load windows on the new drive, stuck at 'starting windows' screen

  So I'm actually down ranking of windows 8 pro to windows 7 pro two 64. I was finally able to get the comp not recongize just load the USB. My problem is that when it does not start, I'm stuck at 'Starting windows' screen I was wondering, perhaps, that I need to format a patition first? It's a new Lenovo warranty hard drive. (Kind of funny how to send CD's for a laptop that doesn't have a cd player only) I looked in the formatting of a usb key, have had some difficulty in finding a reliable way... Thank you

  Hi davefromsb,

  Windows 8 computers have a bios "UEFI" and so will come with "Secure Boot" as well as "UEFI" only start enabled. Disable secure boot if you do not have and choose start to the "legacy" methods The problem is most likely that the image of Windows 7 which has been engraved on the USB key was burned using an instead of a TPG one MBR partition scheme. I hope this helps.

  -Brian Chan

• Delay on the 'Starting Windows' screen

  The problem I have is this, whenever I start my PC there is a delay on the 'Starting Windows' screen. The screen does not freeze or anything just ten minutes to bring up the Log In screen. It's the only time where that the PC is delayed, it has no effect on the operation of the PC. I uninstalled my anti virus and that does make a difference and I have made sure all drivers are up to date. Anyone have any suggestions?

  Thanks for your help.

  Hi Duncan,.

  You did changes to the computer before this problem?

  I suggest you to disconnect all external devices and check if it helps.

  I'd like to as you read the following article and try the suggestions in the article.

  8.1 Windows, Windows 8 or Windows 7 hangs or freezes

  See (see (my computer hangs or freezes on Windows startup screen))
  http://support.Microsoft.com/kb/2681286/en-us

  Anti Virus WARNING: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  You can also read the following article, this will help you improve the performance of your computer.

  Optimize Windows to improve performance.
  http://Windows.Microsoft.com/en-us/Windows/optimize-Windows-better-performance#optimize-Windows-better-performance=Windows-7

  Important: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  I hope this helps to solve the problem. Please come back for any clarification on this or any issue of Windows. We will be happy to help you.

• After the last updates of windows have problems with start up and now drivers

  Hello

  After the last updates of windows have problems with start up and now drivers. I get an error code 21 when I try to install the drivers AMD apparently missing.

  May 14, last night I had several (automatically) downloaded windows update

  Today, I was unable to boot my computer with Windows - tried the disk check, start checks etc, and eventually had to use System Restore (for help before the critical update to restore).

  Perfection, everything works, but knowing that windows will attempt to redo an automatic update, tried to check online - no one seemed to have a problem and (naivly) thinking I could always do another restore of the system, I rebooted again.

  Same thing worse. Could not do a sys restore either just before restarting or last night. Chose a date earlier (last week) but then lost the USB drivers and pilots display. Downloaded updated but refuses to let my AMD driver install Windows I have a very unpleasant screen... and I must now stop the installation of this update "critical."

  Would appreciate advice how do my installed display driver or whether anyone else has problems following this update

  Thank you

  Hi Jane,

  You have a disk to install Windows 7 with you?

  I suggest you to check the event viewer for error details report.

  Open event viewer.

  http://Windows.Microsoft.com/en-us/Windows7/open-Event-Viewer

• I have problems with random blue screens - 1st BC Code - of the suggestions?

  I have problems with random blue screens - 1st BC code - all others are zeros.  6_1_7601 OS version, produced 768_1.  Any suggestions?  My computer is a model of HP P7-1235.

  Thank you.

  The minidump files showed two errors blue screen, an error KMODE_EXCEPTION_NOT_HANDLED (1e) referring to the amdxhc.sys and an error SYSTEM_SERVICE_EXCEPTION (3B) referring to the usbfilter.sys:

  Bugcheck 1E, {0, 0, 0, 0}

  WARNING: Unable to verify timestamp for amdxhc.sys
  ERROR: Module load completed but symbols can be loaded for amdxhc.sys

  Bugcheck 3B {c0000005, fffff8000f4770c5, fffff880085feb10, 0}

  WARNING: Unable to verify timestamp for usbfilter.sys
  ERROR: Module load completed but symbols can be loaded for usbfilter.sys

  The amdxhc.sys is the AMD USB 3.0 driver and the usbfilter.sys is the AMD USB filter driver.

  The amdxhc.sys is dated January 3, 2012 and the usbfilter.sys is dated November 16, 2011.

  Two of these drivers should be updated to the latest version to ensure compatibility with the motherboard and between them.

  HP has an available Update for AMD USB 3.0 driver but I do not see an AMD USB filter driver available for your computer updated.

  I might suggest to try to get the package of motherboard chipset from AMD for versions newer and compatible to the two pilots.

  You can try the "AMD Chipset drivers' starting from the following link which should update the two drivers.

  http://support.AMD.com/us/gpudownload/Windows/pages/raid_windows.aspx#2

  I recommend to create a System Restore Point before installing the new motherboard drivers.