M30X-129: problem ATI after remastering

Similar Questions

• M30X 129: problem of battery or power management road

  Hi all

  I had a lot of trouble with my laptop recently; When using just the battery I can watch it unloads and a minute, he can read about 30% or more, depending on the laptop will be beep like crazy and then go into hibernation. I put it to Hibernate at 5%. I find it incredible that the battery can lose about a quarter of its power in less than 60 seconds.

  I've updated the utility of power management using the Toshiba site, but it has not changed anything. The only time that I have the AC adapter and battery at the same time is when I charge the battery, if I'm near a power outlet and there is no need to reload, I always remove the battery.

  I read on these forums somewhere on the withdrawal of the Toshiba power management and just using windows, but I prefer not to change anything like that, as far as I'm concerned the Toshiba it should do the job! The laptop is still under warranty but my nearest authorized repair center is more than 200 miles away, so, does anyone have any ideas of what I can do or try next? I'm out of ideas...

  Cheers in advance,
  Colin

  Hi Colin,

  You don't say how old is your battery, but it is more likely to be a hardware problem with your battery rather than a problem with the Toshiba power utility.

  It seems that if one or more of the cells in your battery cannot hold its charge properly, and once the remaining cells the battery power exhaustion will fall suddenly.

  HTH

• Satellite M30X-129: CPU fan runs constantly after new XP Pro re - install

  I just installed a new Samsung 120 GB drive in my M30X-129, an upgrade of the 60 GB IBM drive with what it was originally provided.

  Tried ghost XP Home installation of the old drive to the new - but it didn't work for some reason, installation, attached to a page with the "Windows XP" logo on it...

  So, I installed XP Pro with SP2 from scratch on the new drive.

  After having done that, I then installed the Toshiba and utils drivers listed for your laptop:

  NES http://UK.Computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=UK&mode=allMachi & action = search & teddProduct = 555

  The problem I have is that the fan runs at full speed all the time - this isn't the case with the old installation of XP (was rare for it to come on at all when slowed down in the office - running full bore 100% of the time)

  Research by and try a few suggestions:

  -J' installed the common Utils from Toshiba
  -J' installed the Toshieba power management - and set the fan speed to ' Silent' has ', but that doesn't seem to have any effect.

  Any suggestions? for example. where I get the latest versions of the applications?

  The noise of the fan slowly leads me to the top of the wall...

  Ben.

  Hello Ben

  If you have installed your own OS and Toshiba designed drivers, tools and utilities, I assume that this problem cannot be software. I'm really not 100% sure why the fan always runs at full speed but Satellite M30X is around 2 years and I guess it's time to clean up. The second thing can be your new HARD drive.
  It is also possible that new HARD drive produce more heat and sensors to register it and don t stop the cooling fan.

  I recommend you to professionally cleaned the unit and remove any dust inside the unit. I'm pretty sure that cooling fan does not work at all times.

  Also try to put the laptop into a slightly higher position (if possible at the back) and on this brand more interspace between the bureau and the cooling grill fan in the lower corner of your laptop.

• Problem starting after the installation of the NTI Echo Satellite P50-B-11V

  Hi guys. I have problems to start mid laptop computer (Toshiba Satellite P50-B-11V, F04236S) after the installation of NTI Echo3 to migrate the data from the drive HARD original to a new SSD (Toshiba 480 GB Q300 series).

  Error: file/echo not found boot/initrd.gz. Pilot pata-platform...
  Kernel panic not syncing VFS: Don't mount rootfson unknown - black (0,0).

  Anyone facing this problem? Please advice if you have the time.
  I tried several times to repair Windows (F12 key) and I have tried different ways to migrate data but the problem even after reboot.

  Thanks fo your time.

  Posted by marianbur
  

  Hi guys. I have problems to start mid laptop computer (Toshiba Satellite P50-B-11V, F04236S) after the installation of NTI Echo3 to migrate the data from the drive HARD original to a new SSD (Toshiba 480 GB Q300 series).

  Error: file/echo not found boot/initrd.gz. Pilot pata-platform...
  Kernel panic not syncing VFS: Don't mount rootfson unknown - black (0,0).

  Anyone facing this problem? Please advice if you have the time.
  I tried several times to repair Windows (F12 key) and I have tried different ways to migrate data but the problem even after reboot.

  Thanks fo your time.

  Dear marianbur,

  New laptop having same problem here, is now stuck... Have you received still no solution?

  Greetz

• Satellite M30X-129: Microphone does not work

  My Satellite M30X-129 was working well until I reinstalled the operating system.
  Since then, the Microphone does NOT work. I installed the audio drivers from the CD utilities & tools, but it does not work.

  Can anyone help?

  Hello Grondin

  Sorry, but I must ask you something. You speak internal microphone or external?

• Satellite M30X-129 - no video on the second screen

  I have a M30X-129, which for the most part works fine. However, when I have a second monitor attached (for example, an overhead projector) everything is displayed outside a video/film clip, which appears black. This occurs if Windows Media Player or Realplayer is used. All other programs and images are visible on the external monitor or laptop screen.

  I installed Windows XP Pro on the orig XP Home version. All drivers were installed and updated as required. I thnk I have a Raedon graphics card.
  Any ideas on how to have movies/clips on the second screen?

  Thank you.

  Hello

  Most Windows applications and video cards do not support playback of video files on the screens at the same time. You can try to disable the video signal going to the built in LCD screen and display only through the projector.

• Win XP on Satellite M30X does not start after battery was flat

  XP on M30X will not start after battery was flat! Safe mode, last work... nothing works!
  The restore CD offers 3 options1: new installation, 2 toshiba recovery utility (expert mode) und 9 output.

  How do the XP Recovery console, or how to use 2 to restore the system without losing any files.

  Thanks for the tips.
  It is a nite Mare...

  Wolf
  Good day

  The point is that the Toshiba Recovery CD does not have the Windows XP repair console.
  The restore CD contains the image of Toshiba and you can just reinstall the system on the HARD drive and no repair.

  Now you have 2 options of recovery.
  First called standard recovery option would be to format the entire HARD drive and reinstalling the image.
  The second option called recovery expert allows you to reinstall the operating system on a selected partition. Then only this partition will be formatted.

  If you do not want to format the whole HARD drive then you select the second option and select the partition to a new operating system.

• Satellite M30X-129: recovery CD can be run from an external drive?

  My wifi seems to have packed - recognizes nearby wireless networks but does not connect to them - so I will try to use the recovery disk product in the hope that it will bring back wifi.

  However, the DVD Multi drive does not work - light flashes to indicate some sort of activity, but no drive appears in my computer. I think that if I buy the external drive, I can run the product recovery disc for this.
  Is the drive Toshiba external DVD SuperMulti (PA3454U-1DV2) compatible with the Satellite M30X - 129 P - M 735? Product recovery can be run from an external drive (bootable?)?

  Any advice would be greatly appreciated!

  Hello

  According to this page of Toshiba, the drive is compatible with your device:
  e http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/options_and_accessories_search_by_model.jsp?servic = 1 = us & selSeries & selFamily = 2326 & SelCategorie = 2319 & family = 2326 & selP roduct = 98795

  The fact is that only the boot device options available: USB-drive floppy/disk HARD/ODD/LAN
  I know you can only boot from external CD/DVD drive if the device supports this option and the unit.
  In my opinion be100% sure you should ask ASP for advice.

  But know one other question: do you have you boot from the restore CD to recover the operating system?
  If you want to recover the operating system, you have to start on this CD and do not run it under Windows. Check it out

• Satellite M30X-129: card SD2 BT does not work

  I can't get my SD2 BT working on my satellite M30X-129, I get Bluetooth is not ready when trying to make a connection, I'm not sure if it's to do with the SD card drivers or... any ideas please

  Hello

  As far as I know there should be a CD that was shipped with this card.
  There you should find the drivers for this card. If the drivers on the CD don t work then try to update with the latest version.
  For this, you can check this site:
  http://APS.toshiba-tro.de/Bluetooth/

• Using XP Professional... problems caused after the download of Service Pack 3

  Using XP Professional... problems caused after the download of Service Pack 3

  Using XP Professional... problems caused after the download of Service Pack 3

  Only these security updates are not downloaded successfully:

  Security Update for Microsoft .NET Framework 2.0 SP2 on Windows Server 2003 and Windows XP x 86 (KB2742596)
  Security Update for Microsoft .NET Framework 3.0 SP2 on Windows Server 2003 and Windows XP x 86 (KB2756918)
  Security Update for Microsoft .NET Framework 2.0 SP2 on Windows Server 2003 and Windows XP x 86 (KB2789643)
  Security Update for Microsoft .NET Framework 2.0 SP2 on Windows Server 2003 and Windows XP x 86 (KB2804577)
  Security Update for Microsoft .NET Framework 2.0 SP2 on Windows Server 2003 and Windows XP x 86 (KB2833940)
  Security Update for Microsoft .NET Framework 2.0 SP2 on Windows Server 2003 and Windows XP x 86 (KB2844285)

  Microsoft Fix - It ran... computer & rebooted... closed repeatedly...

  Problem persists... Help!

  Lane

  It is a common problem with updates of .NET. Here are the steps I follow

  First try this...

  Download and run the Microsoft .NET Framework repair tool , then visit Windows Update and let it try to reinstall updates. Once it's done, scan again with Windows Update to ensure that they properly installed.

  If the above does not make it...

  Open Add or remove programs, click on .NET 3.5 and choose repair. I got around to test if this fix actually .NET 2.0 and 3.0 of the .NET also, but it's worth it. I do not know if it can also cancel updates already installed .NET. If so, they will reinstall when you perform a Windows update that is the next step after the repair.

  If the repair does not fix it, will add and remove programs and uninstall the .NET Framework 3.5, 2.0, then 3.0.
  Visit Windows Update, select Custom scan and under software, optional install this...

  

  It must be installed by itself. Windows Update will not let you do otherwise.

  When he did install (I forgot if she asks for a restart or what not), scan again and all updates for .NET 2.0, 3.0 and 3.5 of the .NET .NET must appear. Choose to install.
  A new analysis to ensure that they properly installed.

  If all goes well, that will solve the problems you face.

  Make sure you come back and let us know which method worked for you or if you still have problems, I have to run a cleaning tool.

  Good luck!

• Can someone help me solve the problem APPCRASH on Windows 7? The problem occurs after installation of Office 2010

  Hi all

  the OS is Windows 7 SP1 32-bit Enterprise Edition.

  I use an important banking software package called ORF more than Misys, the application is critical for the company, the problem occurs after the installation of Microsoft Office 2010 Professional Plus with Service Pack 2; the ORF more crashes when you try to print to a PictBridge compatible printer.

  I get the following message from crash:

  Signature of the problem:
  Problem event name: APPCRASH
  Application name: orfplus.exe
  Application version: 5.0.1.0
  Application timestamp: 3f6f479b
  Fault Module name: StackHash_802d
  Fault Module Version: 6.1.7601.22436
  Timestamp of Module error: 521eaab0
  Exception code: c0000374
  Exception offset: 000c38b7
  OS version: 6.1.7601.2.1.0.256.4
  Locale ID: 2057
  Additional information 1: 802d
  More information 2: 802d0d721d077b7993d17470b8164201
  3 more information: d6a2
  Additional information 4: d6a2e9e6b15ae70428294b9407d7e88d

  Read our privacy statement online:
  http://go.Microsoft.com/fwlink/?LinkId=104288&clcid=0x0409

  If the online privacy statement is not available, please read our offline privacy statement:
  C:\Windows\system32\en-US\erofflps.txt

  ----

  I tried to exclude the orfplus.exe of the DEP, but that does not solve the problem, the application always crashes when I try to print a report.

  ----

  As a result, we are unable to upgrade our office staff of Office 2010 Professional Plus application.

  I appreciate if someone can help me solve this problem.

  Thanks in advance.

  Hello Matt,

  According to the issue description, it seems that you are connected to a network domain, so I suggest you to republish your query on the TechNet forum and I hope that you will receive a response it a better way that they are trained on the computers in the domain and their settings.

  http://social.technet.Microsoft.com/forums/en-us/home?category=w7itpro

  Thank you.

• I have a problem with After Effects and Cinema 4 d Light.

  Good afternoon. I have a problem with After Effects.

  When I try to create a Cinema4d file via the file menu > new > file Maxton Cinema4d gives the error "the version of Cinema4d (16.038) does not record of resources (16.028) version! Please reinstall the Cinema 4 d correctly.

  How to solve this problem?

  Thank you

  Uninstall 13.7

  Look for this folder and delete: C:\Program Files\Adobe\Adobe after effects CC 2015\Support Files\Plug - ins\MAXON CINEWARE AE

  Re-install AE 13.7

• Problemas con after effects cc 2014

  Tengo problemas con after effects cc 2014 are cuando lo ejecuto sell me an error of Quebec don't be esta generating UN archivo dummy ("Advertencia de After Effects: No. is pudo crear el archivo ' / users/aryavila777/Library/Preferences/Adobe/After Effects/13.2/dummy'." "") Esto're lo as sale me

  fix the permissions problem that prevents to start Adobe applications

• Having problems with After Effects on Mavericks

  I'm having some problems with After Effects CS6 on a MacBook Pro. Here is what I get:

  

  I am trying to date:

  

  And receive this error message:

  

  What I am doing wrong?

  There are a lot of people running After Effects on the Mavericks.  My suggestion is, first of all, check your computer for any 3rd party software which may be at the origin of the conflict. This can include games, the codec packs, video players or the graphics drivers that are not compatible with your system. Then, if the uninstallation of suspicious programs does not resolve the problem, run the cleanup tool Adobe and re - install AE by using the latest version of CS6 or download creative cloud App and download and install AE CC from there.

  Use the CC cleaning tool to resolve installation problems. CC, CS3 - CS6

• From problems with After Effects

  Hi, this is Marc of Germany!

  Today, I bought my subscription for 1 year for the creative cloud. Now, I have some problems with After effects from. First of all, after you download the program reported error U44M1P7. I ignored it and opened the program. After 5 minutes, he showed me the following problem: a plug-in could not be opened after effects CC\Support files\ (Media Core plug ins)\Common\ImporterJEPG.prm. I klicked OK a saw, the following error "taking in Anywhere2.aex, MediaBrowse.aex, Monitor.aex RQ Coulnd't ' t be loaded, (39§ 23) is not support and finally 'After effects can't work" - end of my story. "

  I hope you can help me as soon as possible!

  Thank you!

  Ohne Sessepolster Systeminformationen wird das nix. Entweder die Plugins blockiert material oder werden ist nicht scripte mit den entsprechenden sceen fur Videodekodierung und Anzeige Funktionen. Ansonsten:

  Failed installation. Error U44M1P7 | Updates

  Auch gut possible, dass das Ujpdate die hose worse ist und dadurch inkompatible Komponenten originated sind einfach. Einfach das neu installieren und drüber cleaning tool.

  Use the CC cleaning tool to resolve installation problems. CC, CS3 - CS6

  Mylenium