M475 MFP HP LaserJet Pro 400

Similar Questions

• MFP HP LaserJet Pro 400 M425dn will not print the text to format 72 points or more

  My workplace has recently bought a M425dn of MFP HP LaserJet Pro 400 all-in-one printer. It works perfectly except for the fact that it will not print text that is 72 points or larger in size. I tried many fonts that are installed with Windows, and all them print correctly to the point size 71.5 or smaller; Another thing simply does not appear in prints. Content which is of size to 72 points or more * fact * affect the flow of the content printed on the page, however. It's like the 72 points or larger text takes up space, but it is completely invisible on the printed page.

  I tested using Microsoft Word 2002 on three separate computers, of which two have installed Windows 7 and Windows Vista installed. The problem is the same on all three computers. The printer is connected via an ethernet cable to our wired network. I have installed the printer software included, and I don't think that there are updates for it that have not been installed up to this point.

  Any thoughts on how to solve this problem?

  Hello, I just made an account to solve this problem for you guys because it has been a puzzle to me also...

  I apologize before the huge hand for the terrible grammar and punctuation that I'm in a hurry

  Now it does not work for everyone but I fixed it on my machine with the following

  now before you print it... .use (ctrl + p) in your text editor to open the print window, click (properties), and then navigate to the tab (Advanced) now, I have a section called the characteristics of the printer in this category there is an option to 'send truetype as bitmap' activate this and see if it can help someone of you, for me, with this PERMIT I can print any font size my processor will allow me to type

  in my machine's plug

  Reference Dell d6420

  Win7

  Msoft word 2007

  printer itself is

  HP laserjet 200 color m276

  printer driver is

  HP LaserJet 200 color MFP M276 PCL 6

  I understand that this printer and driver is not identical to yours in itself, but the nature of these drivers makes it highly likely that this solution works for most of you

  If this can help, someone else did post more because I'll probly do not sign in to this site I created this account just for this post and I hope to solve this annoying problem issue for many of you... .no necessary congratulations

• MFP HP LaserJet Pro 400 M425dn cold reset

  Hello!

  Help me! How can I make cold reset HP LaserJet Pro 400 MFP M425dn ?

  You can do 'factory reset' menu of the control panel; or permanent initialization of power first, holding and cover the corner area to the right / left of the control panel when you feed on... release your finger when you see «initialization permanent...» ». After you complete and return the loan, it indicates the reset is complete.

• Help! My M475dn MFP HP LaserJet Pro 400 color printer will NOT print!

  HP LaserJet Pro 400 color MFP-M475dn-CE863A

  Printer on a network and can connect to multiple computers that include: Mac OS X, Windows 7 and Windows XP.

  When I try to print from my iMac, the print queue of the printer says "the printer is not connected.  When we try to print from Windows computers, it is in the right queue and does not print.  When I go the printer itself and try to print a page of demonstration or page supplies directly to him, it says on the screen which is printed, but nothing happens.  This is not hum or anything!  The port where the network cable is connected is switched on green that says HP which means that the network cable is connected.  We've had this printer for a year now, and something like that never happened.

  I did not have any software or anything like that until this happened.  It was working fine on Saturday when we used it, but when we arrived at work today, he just decided that it would interrupt printing!

  I'm puzzled!  I tried 'ping' IP address of the printer from my iMac and it pings fine.  Does anyone have advice?

  (I tried to make of the obvious like too switch the printer on and off and shutting the computer down and nothing!)

  Okay, so I feel a bit stupid right now.  I decided that I would be closed the printer for about an hour to see if it was there, and what you know-it has been!  I had to turn it off several times before but I guess it wasn't long enough.  What a pain!

  Thanks to everyone who took the time to read this!  Sorry to waste time everyone!

• Is the source Support 2 faces 476DW MFP HP LASERJET PRO 400 COLOR document

  A client must be able to analyze and automatically copy 2-sided documents.

  It is clear to me from the leaves of manual and specifications if the ADF of MFP 476DW will automatically handle documents sources 2 faces.

  There is a comment "document feeder of 50 pages with copy double-sided electronic and detection analysis and multiple choice", but nothing in the scan or copy of the sections of the information sheet or manual.

  Can someone confirm that this model will support scanning and copying documents source face double?

  Thank you
  Sean

  Hello Sean,.

  I understand that the MFP HP LJ 476dn Pro and 476dw only supports automatic copy/scan side 2 option.  Automatic 2-sided printing option is not available with the 476nw model, but the ADF scanner always supports the automatic management of document side 2.  Please see the product information available on the following HP to understand the available models & features supported:

  http://www.HP.com/hpinfo/newsroom/press_kits/2014/MWc/ColorLaserJetPro_MFP_M476_datasheet.PDF

  If you are looking for measures actually work to copy/scan, then you can consult the user guide or links to product support available on hp.com (www.hp.com/go/support).

• HP LaserJet Pro 400 M425 MFP: M425 MFP HP LaserJet Pro 400 drivers

  I tried to use the software and the download page driver at HP, but when I use the full installer happens to the party 'detect the product' of the installation, it is 100% and then said it failed because it took a long time.

  Then anyone would be able to direct me to the necessary drivers for my printer please

  I was able to give up the usb connection and went straight to the network to connect but thanks for the help

• grinding noise when my HP LaserJet Pro 400 color MFP M475 calibrates

  When my color HP LaserJet Pro 400 MFP M475 recalibrates, I get a grinding or gear sliding noise.  No idea how to fix it or what to look for?

  Noise problems are difficult to troubleshoot remotely and they could easily mislead even when we are near the unit.

  Please confirm if the noise is a squeak or a noise squeky/hum.

  As you mentioned that this happens only during calibration, it is why I suggest you to double check & validate your toner cartridges.  Among the toner cartrdige is maybe defective and causing this problem.

  If not the toner cartridge, then it would be one of the components of hardware printer that is at issue, where a Tech HP may need to perform a physical inspection of the aircraft and the error condition.

• LaserJet pro 400 mfp wil not install

  I tried setting my new laserjet pro 400 color mfp m475dn, two upward ways described in the installation guide; either via the automatic installation and CD rom. I followed the instructions exactly each 10 times I tried. I even downloaded the software again on the HP site and tried to install that. Each time the same result:

  "Install operation has been too long..." Fatal error etc."after he had reached and hung 99% installed.

  Any ideas guys?

  I am running Windows Vista Ultimate 64-bit.

  See you soon,.

  Neil.

  ndpadgett,

  You have two options:

  1. If you try to install this printer via a USB port, please do a network install and use the driver from hp.com.

  M475 solution print driver full

  2. If you unble to do a network installation, then please look to see if you have a universal print driver installed on your machine. If you do, then you must remove the UPD driver, re-boot and re - install the m475 SW.

• turn off the broadcast without wire - HP laserjet pro 400 color mfp m475dw

  How do I disable broadcasting SSID for HP laserjet pro 400 color mfp m475dw.  I disabled the configuration via the web console wireless printer, but it is still broadcasting.  I also updated the firmware to 20131028 last available.

  Since it is wiered one of the scenario, I could solve this with the help of the HP Support is by doing factory reset/NVRAM reset the unit by turning the printer and holding right arrow and cancel on the touch screen of the device (cancel is on the lower right of the touch screen on the black area and right arrow is just above him (one in the middle of the Panel) in the same black box) and the device of turning on until the message something like storage reset... is displayed and can release the two buttons/zone button.

• LaserJet pro 400 m425dn mfp: mfp laserjet pro 400 m425dn will not connect to the network

  I just bought a mfp laserjet pro 400 m425dn printer/phtocopier and I can't seem to connect to our network.  I have it plugged into the router and it says "cable disconnected" without an IP address.  I don't have the USB cable to configure the machine and I was hoping to do it via the network (which tells me is an option).  I don't know if that has something to do with it.

  Any help would be greatly appreciated.

  The printer should be released the box set up using DHCP for addressing.

  When plug you it into the router it should pull an IP address, if it is its cable disconnected then you might have a bad port on the router, a bad cable or a bad printer.

  Plug something else into the same port with the same cable and see if it works, if you have a defective printer and need to return it and get a replacement.

  You may also be able to find someone to replace the trainer who has the network port to it.

  If my post is solved your problem and click the accepted as button solution under him.

  In order to thank a Tech for a post click the thumbs up button under the post.

  You can even click on the two keys...

• LaserJet Pro 400 MFP: LaserJet Pro 400 prints not Google Chrome

  Sorry, please answer my question in the forum somewhere but I can't find.

  Since I got my new LaserJet Pro 400 MFP I can print is no longer things such as my weekly payroll tax receipts.  I use Google Chrome.  When I try to print, I get only the options to 'Save' or 'Cancel' so I have to save it, then go to My Documents, find it and print it out.  I would really like to continue to use Google Chrome, so it's an another printer driver that I need to use?  Thank you!

  Hello

  You need not of any other driver, just point Google chrome to the right pair...

  Google chrome opens the print dialog box, and then press the button change.
  Select your printer from the list instead of the default save as PDF option and try to print again.

  Shlomi

• HP LaserJet Pro 400 MFP M425 - paper supply is still legal

  HP LaserJet Pro 400 MFP M425

  IM unable to have paper paper feed use.

  I can scan with the scanner bed and there select the paper letter correctly, but when I try to use the paper feed its still legal size

  Ive has restored to the default factory settings, but still the problem persists.

  How can I make the change to have select letter size.

  Thank you

  Hi @biggddc and welcome to the Forums of HP.

  I'm sorry, but to get your question more exposure I suggest posting in the trade forums since it is a commercial product. You can do to Commercial Forums of LaserJet HP.

  I hope this helps!

• Where is the location of the fonts on LaserJet Pro 400 MFP M425dn dimm?

  I recently bought a LaserJet Pro 400 MFP M425dn and to install a strip of memory custom font I bought for another printer that accepts fonts DIMM.

  The problem is that I can't find the font dimm location, even if the configuration of the printer said very clearly that there is a 'Slot DIMM 1. Said user's Guide: 'this product includes a panel of memory which will accept the following third party font and barcode... '. "- but it does not say where is this"sign of memory. "

  There is a door on the left side of the printer, but it has only a rectangular socket, not a DIMM slot.

  Can anyone solve this mystery? Thanks much for any help.

  Thanks - but it was not the question. I'm not trying to add memory to the printer, but instead to add a MEMORY programmed bar that includes additional fonts.

  For the love of someone else who may be interested, I finally found the answer to my own question on TypeHaus website:

  This side door on the left (in fact) the door to the DIMM of fonts. I didn't recognize it as a door of police-dimm because the last style font dimm HP uses different hardware than what they used in the past. The new design doesn't have the pins on one edge of the DIMMs, as do the older styles, but instead uses a rectangular connector on the underside.

  You can see the answer here:

  http://typehaus.com/pubs/custom/Fcd1/insg/Custom_Fcd1InsgHpxx120611AS.PDF

  The illustration is specifically a D401, but the design of the door and socket are identical to the design door and taken on the M425dn.

  I hope this can help someone else who may be as puzzled as I was!

• Unable to connect to the HP ePRINT with Color LaserJet Pro 400 M475dw MFP website

  LaserJet Pro 400 color multifunction m475dw-Just installed. Print, scan, copy and fax all works fine! use of WiFi

  Using IMAC OS 10.8.2 with all updates

  Netgear DGN2200v3 router using

  Printer not connect to the HP ePrint website

  Printer connects using Hp and profile for fax set up etc.  But the "HP Web Services" article when enrecorded and hit the Activate button - it does not connect to the site - it seems just to refresh.

  "If I try to connect thro the printer not the imac and try to activate the web services, it says" connection "on the screen BUT after a few minutes of trying - so says" CONNECTION ERROR - the printer is unable to connect to the service. Check the internet connection

  ANY IDEAS - HAVE I MISSED SOMETHING?

  Thank you very much

  I try to pull up the built-in web server (EWS) by entering the IP address of the printer in a browser and set a static IP & DNS address.

  The information for the default gateway, subnet mask and IP address can be accessed from the Setup menu on the front panel, go to settings > reports > network summary and it will print off the coast.

  Once you entered the IP address in a browser and have the EWS pulled up, go to the tab above titled "Networking". Then click on IPv4 in the left column; who will bring to the top of the address configuration page.  Place the manual radio button and fill in the IP address, the default gateway and the subnet mask with the information from the report. You don't fill the part entitled WINS server, which can be left alone.

  You will then want to fill in the DNS of the page part, the favorite should be set to 8.8.8.8 and the alternative/secondary must be set to 8.8.4.4. Then click 'apply '.

  Power cycle the printer. Turn off the power, wait 30 seconds and then turn it back on. Once it is fully operational, try again to connect to web services.

• LaserJet Pro 400: Watermark not printing on Laserjet Pro 400 on Windows 8

  On the computer of Windows 8, watermark does not print on Laserjet Pro 400 connected by USB. Please note: the function watermark works on other printers not HP, as our networked Ricoh copiers. The printer prints a watermark on a Windows 7 computer. Using the driver package LJM351_M451_Series-12200-drv_installer.

  Very hard to advise without additional evidence (such as samples).

  With my Windows 8.1 Pro 64-bit system, I can print watermarks on my LaserJet Pro MFP color 400 M475dn (equivalent of MFP M451) device.

  Attached is a zip container file:

  • Small text in the abcde.txt file that contains the text "abcde".
  • Print file abcde.prn contains the print job generated by opening the text file in Notepad and by printing the document (using the driver of HP LJ300-400 color MFP M375-M475 PCL 6 (61.120.5.12262) UPD version 5.3.0.12262), by specifying the "SAMPLE" watermark with the default settings; exit 'captured' by using the option "print to a file.
  • Text file abcde.prn_analysis.txt contains an analysis of the contents of the print queue.
  • PDF file abcde_scan.pdf shows a scan of the printed output by sending the contents of the direct .prn file to the printer port.

  Try to send the contents of the .prn file direct to your printer port; for USB connect, you must use something like:

  copy  /b  abcde.prn  \\computer-name\share
  

  in a Windows command prompt session, where:

  the computer name is the name of the workstation;

  share is a share of the Windows printer instance name.

  The resultant prints show the watermark of the SAMPLE ?

  If so, then the printer handles the commands to the printer (in this case using PCL XL) OK.

  Can generate something similar to your driver for analysis?

  [You will probably need help moderating to attach files in this forum].