Mac with 10.6.8 newly installed does not detect printer

Similar Questions

• Total memory of 4 GB newly installed does not appear in the Task Manager

  Total memory of 4 GB newly installed does not appear in the tab of the Task Manager performance. Only 3.3 GB appears. Is something wrong with the chopsticks of mem or mem from Vista 32 bit OS limit uses at this level. I have SP2.

  http://support.Microsoft.com/kb/929605

  "System memory shown in the system information dialog box in Windows Vista is less than expected if the 4 GB of RAM is installed.

  This behavior is the expected result of some hardware and software factors.

  Various devices in a typical computer require memory-mapped access. This is known as memory-mapped i/o (MMIO). For the MMIO space is available for 32-bit operating systems, the MMIO space must reside in the first 4 GB of address space.

  For example, if you have a video card that has 256 MB on-board memory, that memory must be mapped in the first 4 GB of address space. If 4 GB of system memory is already installed, the part of this address space must be reserved by the graphics memory mapping. Graphics memory mapping replaces part of the system memory. These conditions reduce the total amount of memory available to the OS System.

  The reduction in available system memory depends on the devices that are installed in the computer. However, to avoid potential driver compatibility issues, 32-bit versions of Windows Vista limit the total available memory to 3.12 GB. See the section 'More information' for more information on potential driver compatibility issues.

  If a computer has many features implemented, the available memory can be reduced to 3 GB or less. However, the maximum memory available in 32-bit versions of Windows Vista is typically 3.12 GB.

  See you soon.

  Mick Murphy - Microsoft partner

• Designjet 110Plus NR: HP Designjet 110 Plus NR Maintenance Utility does not detect printer

  Hello

  I have a Designjet 110 Plus NR printer that prints, but when you use the maintenance utility, it does not detect printer. I downloaded the latest version H.06.0 and am able to install it. but when the search for the printer it will not find it, and I have no way to pinpoint it too my printer. I have the printer connected to my computer via the USB port on a docking station HP residing in my laptop (Elitebook 800 G1 win 7 pro x 64). Also, it is connected via a parallel to the NIC dongle to make it available on the network for everyone to print too so. All can print, I can print but the Cyan is not always print and before you buy new print heads, I would like to clean and align with the Maintenance Utility. I tried to use the printer in the dock station, plugging directly into the laptop and the network to connect, but won't find printer. I tried the alignment of the front that I found in other forums, and it did not work. Whenever I went to the printer, I uninstalled all drivers and and the computer and rebooted system maintenance utilities. I installed the drivers from the HP website, from the disc initially supplied with the printer and our network, still no change print server. Am still able to print but not to run diagnostics or alignments. I've scoured the forums HP and all the "recommended" patches have never someone who in fact confirms the
  'Fix' worked. Can someone help with this problem? It has been about 4 days that I'm looking into this and frankly it's kinda ridicolous saw that it's a plug-and-play printer. Thanks in advance for any advice you may have!

  Well, the network adapter has failed. I managed to install the software, but he gave a generic IP address of the printer and gave me the same mistake of not being able to communicate with the printer. So, I pulled up an old laptop XP downloaded the drivers from the HP site, rebooted, printed the test page with success and installed the system maintenance utility. And WHOLA, I saw the printer immediately in the USB of Maintenance section and was able to run the diagnostic page and determine our problem. Thanks again for your help Mike!

• HP 8500 replaced, software does not detect printer even though I can't ping / connect to the web interface

  Windows 7 Pro 64

  Reference Dell

  Printer connected via ethernet

  software worked well until the printer has been replaced by HP under warranty

  in the new device, the screen of the wizard to set the time/language etc.

  Software HP does not detect the device and so I can not use all the features.

  I can connect to the printer via IP and also tried to put the TCP/IP port with printer static IP. Can I print using this, but the software "suite" does not detect the printer.

  Removed all software, cleaned the registry, removed the IP port, re-installed the software, does still not detect printer.

  Installed HP printer diags and it passes all the tests, but the suite software HP will always be NOT detect printer.

  Tried without firewall, tried with, still can ping printer, connect to the web interface, the static value, always the software does not detect the printer... so whats left to please other than an another replacement warranty which is used to solve the problem, as it is definitely bad coding in the suite.

  I also tried downloading drivers/full later on the HP site.

  Note that all windows updates are met, reconstruction is out of the question that it is a machine of the company and would almost take me 3-4 days to replace all the software on it (Sage, DW, COFFEE, HMRC).

  Hi-Dillion, Declan

• Newly installed does not open Lightroom CC

  I just install Adobe Lightroom CC. Downloaded fine but when I click on the application there is a quick on my screen flash and then nothing?  Can you help me >

  I tried recording off CC first, the rear connection and then put it back, and it seemed to work

• I have a problem with the cloud creative apps install does not work

  Hi, there is a problem with the Office of cloud when I tried to update or the Office checks the update there is an error message that I need to contact support.

  I am tired of the destop to uninstall and reinstall it but the problem still there.

  Could you please help me?

  what I have to do. I validate responses to your help page but nobody not corresponding to my problem...

  Thank you for your kind reply

  Soniablanco please try to remove the following directories from users / Library/Application Support/Adobe

  • AAMUpdater
  • OOBE

  Please make sure that you are in the library folder of the user rather than the main folder of the library.  Remove these files in/Library/Application Support / Adobe / will require a reinstallation of applications to recover the files.

  AAMUpdater and OOBE records are therefore two specific users may be why you see the behavior under only the migrated user account.

• Laptop does not detect WiFi or USB

  My laptop was running on Windows 8.1 and I decided that I wanted to go back to Windows 7. I installed Windows 7 Ultimate, but now my laptop does not detect my Wi - Fi. I thought I should just update the driver associated with a wifi adapter but it does not detect my Flash drive either. I tried to reinstall Windows 7 and Windows 8.1 but I still have the same issues. Help?
  
  Quick notes:
  Computer: HP DV7
  Operating system: Windows 7 Ultimate

  Using HP recovery for your computer media, he would return to a factory State... including all partitions of the plant, operating system, drivers and HP software. The HP recovery media should solve all problems, except those that are from the real hardware.

  Otherwise, you can download the drivers from the page that was provided and install them. Once again, just after the "Hardware ID" string for any unknown devices.

  If you have any other questions, feel free to ask.

  Please click the 'Thumbs Up' white LAURELS to show your appreciation

• Windows XP missing HAL. DLL file. CD ROM does not detect the Windows XP installation CD.

  I received the error message to the Windows startup, that I need to replace my Hal.DLL file.  I can't access a safe mode with command prompt, and CD rom does not detect the CD. I have rebuilt the Boot.INI file and still no luck. I tried to put HAL. DLL on a flash drive, but it cannot read it for some reason any. "Cannot develop"...

  Any help would be appreciated!

  Go to the store and buy an optical drive. They are very expensive. No, you cannot use the optical drive of your laptop. You can possibly create a bootable USB key with a distribution of Linux on it and copy the correct boot hard disk files. I say "may" because not all older computers can boot from a USB device. Look in your BIOS to see if your computer has this capability. If he can:

  http://www.pendrivelinux.com

  If you have not backed up your data, then you have trouble. While you're at the store also buy an external hard drive. You can start the computer with a Linux Live CD (in your new optical drive), and copy the files on the external hard drive. Then you can continue to try to repair your computer.

  MS - MVP - Elephant Boy computers - don't panic!

• Hello, im trying to install CS2 for my mac (yosemite 10.10.3) but it does not work because PowerPC is required! This means that I can't use cs2 with my version? and if I want to use ist what to do? Thank you friends :)

  Hello, im trying to install CS2 for my mac (yosemite 10.10.3) but it does not work because PowerPC is required! This means that I can't use cs2 with my version? and if I want to use ist what to do? Thank you friends

  CS 2 is very old version that uses Power PC, but a newer version than Mac's Intel based processors. CS 2 has been designed according to the Power PC architecture.

• Outer island, I have installed does not appear in 'my computer '. It has been configured for mac. How can I get that back to windows 7

  Outer island, I have installed does not appear in 'my computer '. It has been configured for mac. How can I get that back to windows 7

  What device?

  It appears in the Windows Device Manager?

• Windows XP does not detect any internet at all despite the computer with the modem to work.

  I recently installed Windows XP Professional on my new iMac via bootcamp.  While Windows itself works fine, it won't connect to internet at all.  Despite being connected to a modem ADSL via a Ethernet cable, and also have wireless internet, Windows does not detect any signal.  On the internet in the Control Panel, all connections page that appears is "1394 connection" under the heading "LAN or Internet high speed."  I tried several times to put in place a new internet connection through the Setup Wizard and everytime, no internet is detected.

  I know that the modem works because all the other computers in my house are fine online, including on the side of Mac of the iMac.  If anyone has an idea as to how I should resolve this problem, your help would be greatly appreciated!

  Thank you

  Daniel

  Moreover, these are things I've already tried:

  I've tried to manually and automatically set up an internet connection
  I spoke with my ISP, the modem works fine
  I have re-partitioned the hard drive and reinstalled XP

  The "1394 connection" is the IEEE 1394 (FireWire) from your computer.  There should be cable system and under the heading wireless connections "LAN or Internet high speed."   There is no need to run the Network Setup Wizard or set up a new connection.

  Open the Device Manager (Start > run > devmgmt.msc ) and go to the network adapters section.  You may need to install the drivers for them.

• Cannot install Win 8 - Satellite Pro C660 does not detect HARD drive

  Hello

  My HARD drive died, so I decided to upgrade my Satellite Pro C660 - 1 9 to an SSD.
  I made a USB bootable with Win8 and starts very well.

  The problem is that it does not detect my SSD, so I can proceed with the installation.
  SSD appears in BIOS but not in Windows Installer.
  He said that there is a missing driver.

  I downloaded the AHCI drivers (XP, only ones available) and even in this case, after you have selected the only rider that appears, it says no new device found.

  I tried to change the SATA from AHCI mode to compatibility mode and it's the same thing...

  What can I do?

  Thanks for the help.
  Best regards
  Bruno Moreira

  More old Windows XP need a driver AHCI Intel's but I think this isn't a problem with SATA driver missing because as far as I know Windows 8 as well as Win 8.1 already contains the drivers to recognize the SSD or HARD disk drive.
  In addition, the installation of the OS should be possible even if the driver would be added for this procedure, you must use the "compatibility" mode
  As you say, the compatibility mode is not working too, so I think there is another problem.

  However, page driver Toshiba also provides a driver Intel RST (Intel Rapid Storage Technology) (Windows 8 - updated) you can try to add during the installation of the OS.

  But I m wondering if you would be able to install this Win 8 on common SATA HDD.
  Have you tried to format the SSD using a different computer, then install Win 8?
  Give it a try.

• After a clean install of Windows Vista, Intel Wifi card is installed and activated, but does not detect the network.

  Wireless card not working after a clean install of Windows Vista

  I did a clean install of Windows Vista Home Premium on my HP Pavilion of 32 bits. I've completely updated Windows via Service Pack 2. Given that the clean install, my wireless card, Intel (r) Wireless WiFi Link 4965AGN, was not able to detect all the networks. The Wifi card is listed under NICs as being installed and activated. the hardware on my laptop Wifi switch is set on "on" and the light is blue, indicating that the card is working.

  I can connect to the internet if I connect physically my computer to the modem with an ethernet cable wireless, so the modem isn't the problem. Other computers can connect to the wireless modem, so my Wifi modem functionality is not the problem. The problem with my computer.

  I tried to uninstall the Intel driver and reboot my computer with the generic driver. Install the driver generic, but my wireless card has not always worked. I then ran an update of windows, nothing helps.

  I tried to install the "Intel® PRO /? Wireless and WiFi Link"drivers for Windows Vista (32-bit 13.1.1.1 the latest version and the previous version 12.4.4.5 32-bit) for the Intel® Wireless WiFi Link 4965AGN directly from the Intel Web site at http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Wireless+Networking&ProductLine=Intel%C2%AE+WiFi+Products&ProductProduct=Intel%C2%AE+Wireless+WiFi+Link+4965AGN. The map didn't always work with a driver.

  In addition to the pilots, I also downloaded a tool of diagnosis of Intel (Intel® PROSet /?) Utility of WiFi wireless connection for Windows Vista 32 -? Bit). Said diagnostic tool the WiFi card is not installed or enabled, however, Device Manager maintains that he is also installed and active.

  Is there a problem that causes Device Manager to say that all is well with the card, but does not map to realize that they diminish the radio signals? Everything's fine, diagnostic, it just does not detect networks around him. Help, please.

  Hello

  The on/off switch actually works?

  Since it is an internal adapter to ensure it is enabled in the settings of configuration/F2 (BIOS/CMOS) often like you
  Start - so look at the screen.

  Have you tried the computer on other WiFi networks? You had a WiFi type problem before the
  Re-install of Vista?

  ---------------------------------------------------------------------------------------------------------------------

  Your router could be suspicious here, you have successfully updated its firmware as a possible solution? And I would like to
  Update your WiFi drivers on computers. How you are positioned in the router? Are there
  obstacles in the path?

  Actually try updating your driver and disabling the network logon.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Win version first elements 14 rather than Mac version you downloaded. Serial number does not work. How to get the right serial number

  Win version first elements 14 rather than Mac version you downloaded. Serial number does not work. How to get the right serial number?

  It is unclear what problem you are facing... the wrong version or the wrong serial number.  The serial number is likely for the other version.  You don't want the serial number of Windows or the Mac version?

  One of the following conditions may be useful...

  You can exchange languages/platforms for a newer version product if you follow the instructions on the following link:

  l http://helpx.adobe.com/x-productkb/Policy-Pricing/Order-Product-Platform-Language-swap.htm

  To the link below, click on the still need help? the option in the blue box below and choose the option to chat...
  Make sure that you are logged on the Adobe site, having cookies enabled, clearing your cookie cache.  If it fails to connect, try to use another browser.

  Serial number and activation support (non - CC) chat
  https://helpx.Adobe.com/contact.html?step=PHSP-PHXS_downloading-installing-setting-up_lice nsing-activation_stillNeedHelp

• My mac does not detect my hard drive after the upgrade. How to solve this problem?

  My mac does not detect my hard drive after upgrading to Mac OS Sierra. How to solve this problem?

  Please provide more detailed information. You can read write an effective communities of Apple support question. Maybe you could open disk utility and take a screen snap so that we can see what you see.

  To post a screenshot

  1. Press command + shift + 4, that will change the cursor to the line of sight.
  2. Hold down the mouse button and the collimator allows you to select the part of the screen you want to capture.
  3. Release the mouse button and the image will be saved on your desktop.
  4. Click on the camera icon in the toolbar of the message forum Editor.
  5. Drag the image on the button select a file and click the Insert button.